RF-14-198M
Inspection Worksheet
Miami Shores Village
10050 N.E. 2nd Avenue Miami Shores, FL
Phone: (305)795 -2204 Fax: (305)756 -8972
Inspection Number: INSP- 206559 Permit Number: RF -2 -14 -198
Scheduled Inspection Date: May 09, 2014 Permit Type: Roof
Inspector: Rodriguez, Jorge
Inspection Type: Final Roof
Owner: AQUILINO, NANCY Work Classification: Tile /Flat
Job Address: 9148 N MIAMI Avenue
Miami Shores, FL
Project: <NONE>
Phone Number
Parcel Number 1131010140010
Contractor: PAUL KAWALEK ROOFING CO. Phone: (305)754 -0191
comments
TEAR OFF EXISTING TILE ROOF, REPLACE WITH A
NEW EAGLE BEL AIR COLOR THROUGH 13' FLAT
CONCRETE TILE, COLOR IS CALLED ROYAL PALM
WHICH IS LIGHT GRAY
Passed
Failed
Correction ❑
Needed
Re- Inspection
Fee
No Additional Inspections can be scheduled until
re- inspection fee is paid.
INSPECTOR COMMENTS False
Inspector Comments
May 08, 2014 For Inspections please call: (305)762 -4949 Page 4 of 21
F.I.E.
FLORIDA INTERNATIONAL ENGINEERING
&TESTING LAB
INSIGHT - INNOVATION - INTEGRATION
Owner's Name:
Job Address:
Roofing Contractor:
Permit Number:
Florida International Engineering and Testing Lab LLC
16701 SW 117 Avenue, Miami, FL 33177
Telephone: (305) 378- 1991 -Fax: (305) 378 -1997
Miami -Dade Lab Certification # 07- 0612.11 -State of Florida ca #27273.
SITE SPECIFIC INFORMATION
n
14,
Approximate Roof Height: feet
Type of Access to Roof: 4/ Ladder
f
Type of Tile: � ''F t-0A &a
Slope: l '2- Approximate Square Footage: V& ft2
OtherRequired T sting Force: 35 lbs. Testing Equipment: F.G.E. 100 Shim o Instrument
----------------- Date Installed: `z �L?f� rt Date of Inspection: 1
c�-c �+ {�-� � -� 44--- - - - - --
TEST RESULTS
P= PASS, F= FAIL
--------------------------------------------------------------------------------------------------------------- --- - -•
IN ACCORDANCE WITH THE CRITERIA OF PROTOCOL TAS 106, THIS ROOF ASSEMBLY HAS PASSED THE STATIC UPLIFT QUALITY CONTROL TEST.
ADDITIONAL TEST INFORMATION
Perimeter Width: ft
Area
Units or ft2
No. of Tests
Perimeter
Field
Corners
Hips & Ridges
e— 'Z 5'c�
% %1151ttu®®®
RESP�yD BY:
CEN
®� No 63107 :2
- * � 1� ��
A E Uj
vif>l i1�iT>f3ala e v �}� � � e*
Stay Sft0c 0 ®7
MEME
OMEN
SEEM
NONE
MEME
SEEN
■M■■
mmmmmm
MmMMMM
mmmmmm
mmmmmm
mmmumm
MMMmMM
MM.,MM
MMMMmM
RE: Permit # W —) - -1 q - I "I 6
Miami Shores Village
Building Department
10050 N.E.2nd Avenue
Miami Shores, Florida 33138
Tel: (305) 795.2204
Fax: (305) 756.8972
INSPECTION AFFIDAVIT
DATE: -S 191 I `I
I PavA kowind licensed as a n Contractor / Engineer Weer /Architect,
(Print name and drde License Type) FS 468 Building Inspector
License t ®b 8 S O D O O r7
On or about ), M I H 10!30 N&A , I did personally inspect the roof deck nailing and
(Date &time)
Secondary water barrier work at qJ 9 g v ° ml ckw kve
(Complete Job site address)
Based upon that examination I have determined the installation was done according to the Hurricane Mitigation Retrofit
Manual (Based on 553.844 F.S)
Signature
State of Florida
County of Dade:
The undersigned, being the first duly swom, deposes and says that he/she is the contractor for the above property
mentioned.
Sworn to and subscribed before me this day of Ra i'ch
Notary ublic, Sate of Florida at Large T T COAWWa
rY 9 Dann M Feudarho
a to Expires 01 /12/2016
•General, Building, Residential, or Roo core or any individual cs:rtified under 468 F.S. to make such an inspection. Indude photographs of each plane of the root with
permit # and address # deafly shown marked on the deck for each inspection
Revised on 5I21/2QOkJ
y Miami Shores Village
Building Department
90050 N.E.2nd Avenue, Nami Shows, Florida 33138
Tea: (305) 795.2204 Fax: (305) 756.8972
INSPECTION'S PHONE NUMBER: (305) 762.4949
BUILDING
PERMIT APPLICATION
Permit Type: WELDING
JOB ADDRESS: �� t Kam Ave,
FBC 20
Permit No.
Master Permit No. (L
ROOFING
City: _ County: A JWW+ Dade may
Folio/Pamew.
Is the Building HlstorkaRy Dedpated: Yea NO Flood Zone-
OWNER: Name (Fee Simple 9
a -9ilOf .# -.a
It
state: V7L zip :,.31��
Tenant/Lessee Name: ph,
Email:
CONTRACTOR: company Name: VaW jit7lxwo iej� Roo° jngj Lea phone#: -3o5 f7Sq' —Viq!
Address: 5141 6`w, t b g4JN --re
rr
City: Wl ra- o r State:
QualitiierName: PayJ ln/l E Phone#:
State Certification or Registration #: Certificate of competency #..-0-6 M 0008 r7
Contact Phone#: Email Address:
DESIGNER: ArchitectrEngineer: phonet
Value of Work for this Permit: $ 1 0 Dy
1 SgaarelLinear Footage of Work: 111 00
Type of Work: DAddition O on Mew air/Replace Memo4don
M
Color duu dk:
RA
Submittal Fee $� t )-U J P Fee $ CCF $ MCC $
Scanning Fee $ Radon Fee $ DBPR $ Bond $
Notary $ — Tndmb*WAucadon Fee $ _ Technology Fee $
Double Fee $ 5trnetural Review $
TOTAL FEE NOW DUE $
Bonding Company's Name (if applicable)
Bonding Company's Address
Y City State Zip
Mortgage Lender's Name (if applicable)
Mortgage Lender's Address
City State
�P
Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has
commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating
Construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRICAL WORK, PLUMBING, SIGNS,
WELLS, POOLS, FURNACES, BOILERS, HEATERS, TANKS and AIR CONDITIONERS, ETC.....
OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all
applicable laws regulating construction and zoning.
"WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF
COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR
IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN
FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE
RECORDING YOUR NOTICE OF COMMENCEMENT."
Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must
promise in good faith that a copy of the notice of commencement and construction lien law brochure will be delivered to the person
whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site
for the , first inspection which occurs seven (7) days after the building permit is issued. In the absence of such posted notice, the
inspection will not be approved and a reinspection fee will be charged.
Signature 4
Owner Agent ��!!
The fore going instrument was acknowledged before me this
day of V4f 2011, by C iFd
who is personally known to me or who lilm produced 1
As identification and who did take an oath.
NOTARY PORLIO:e 4 /1
APPROVED BY
Notary Public - State of Florida
My Comm. Expires Apr 9, 2014
ComYnission # DD 949187
Bonded Through National Notary Assn.
Signatare
Contractor
The foregoing instrument was acknowledged before the this -
day of — OQL4 , byT900 j Ica W!q %/ _
o is personally Irno or who haaproduced
es identification and who did take an oath.
Plans Examiner.
NOTARY PUBLIC:
Sign:
F�
Zoning
Structural Review Clerk
(Revised 341=012)(Revised 07110/0WWsed 0000M)(ReWsed 3n s)09)
Miami Shores Village
Building Department
10050 N.E.2nd Avenue
Miami Shores, Florida 33138
Tel: (305) 795.2204
Fax: (305) 756.8972
OWNERS'S AFFIDAVIT OF EXEMPTION
ROOF TO WALL CONNECTION HURRICANE MITIGATION RETROFIT FOR EXISTING SITE -
BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES
PERSUANT TO SECTION 553.844 F.S.
To: Miami Shores Village Building Department Date:
10050 NE 2^d Ave
Miami Shores, A 33138
Re: Owners Name: W-M.-Y K-Qul I t W
Property Address: q 1419 IV, 1%ict v l AVe
Roofing Permit Number.
Dear Building Official:
LINni 4^4 1'- of) Ai 0 certify that I am not required to retrofit the roof to wall connections of my
building because:
M/The just valuation for the structure for purpose of ad valorem taxation is less than $300,000.00. Please attach proof of ad
valorem taxation.
o The building was constructed in compliance with the provisions of the Florida Building Code (FBC) or with the provisions
of 1994 edition of the South Florida Building Code (1994 SFBC)
/ii. / _"
Signature
l
State of Florida
County of Dade
Print Name
The undersigned, being the first duly swom, deposes and says that he/9 Is the owner for the above property mentioned.
Sworn to and subscribed before me this u -day f J `� �/
Z� y o L
GABRIEL GODUR
,�OgiµY P48y4
r o Notary Public - State of Florida
Notary Public, Sate of Florida at Large My Comm. Expires Apr 9, 2014
commissrun b ^f 949,87
'I•�� .` -�� Bonded Th,- ;p 1O , AS<
• When the just valuation of the structure for purpose of ad valorem taxation b equal to or rrrore than $300,OD0.00, and th ngwr��ed arith FBC nor a 1994
SFBC. Then you must provide a building application from a General Contractor for the Roof to Well connection Hurricane Mitigation.
Revised on 5/2111009
•
FEB O 3 2014
Master Permit No.
CITY
Section A (General Infonnation)
Process No.
Contractor's Name �ti ° ° I 1 ®_ 1 l !� n.
Job Address g I q j Iv r i�� l r11 �yVt l N e
❑ Low Slope
❑ Asphaltic
Shingles
❑ New Roof
ROOF CATEGORY
❑ Mechanically Fastened Tile
❑ Metal Panel /Shingles
HIGH - VELOCITY HURRICANE ZONES
�MOrtadAdhftive Set Tile
❑ Wood Shinglewshakes
❑ Prescriptive BUR -RAS 150
ROOF TYPE
Reroofing ❑ Recovering ❑ Repair ❑ Maintenance
ROOF SYSTEM INFORMATION
Low Slope Roof Area (SF) Steep Sloped Roof Area (SF) Total (SF)
0 Woo 91,400
Section B (Roof Plan)
Sketch Roof Plan: illustrate all levels and sections, roof drains, scuppers, overflow
scuppers and overflow drains. Include dimensions of sections and levels, clearly
identify dimensions of elevated pressure zones and location of parapets.
LIS
2010 FLORIDA BUILDING CODE
f �
HIGH- VELOCITY HURRICANE ZONES
Florida Building Code Edition 2010
H10 Velocity Hurricane Zone Uniform PenrQt Appaceyon Form.
Section D (Steep Sloped Roof System)
Steep Sloped Roof Svstem Description
Deck Type:
Un
Roof Slope:
3 :12
1 V- -z'®,nfl wood
ddkrimwv"e -f.
-....1 v-�el+
lation:
. M A
Fire Barrier:
A//A-
Ridge Ventilation? Fastener Type &Spacing: Ei/q =4, �
Nl 11
dheSiYe Type: p f%
ype Cap Sheet: 9®I (A� � d
Mean Roof Height: V; 1
2010 FLORIDA BUILDING CODE — RESIDENTIAL
Covering: r 13 Colarv+
Type & Size Drip li '
dge:
r �
" . }
HIG "- VELOCITY HURRICANE ZONES
Florida Building Code Edition 2010
High Vela Hurricane Zone Uniform Permit Application Form.
Section E (Tile Calculations)
For Moment based tile systems, choose either Method 1 or 2. Compared the values
for M, with the values from M( If the Mr values are greater than or equal to the Mr
values, for each area of the roof, then the file attachment method Is acceptable.
Method 1 "Moment Based T' a Calcula�tiigns Per RAS 127"
x x ►�1� = di - Mt � = Mrt a1l!% Product Approval Mr 4®®y
Ma no 1 - Mr Product Approval M, D
(PA W7 _ x _ - M; - uy =M
rs � Product Approval Nir ®F Y.r
Method 2 "Simplified Tile Calculation Per Table Below"
Required Moment of Resistance (Mr) From Table Below Product Approval Mr
Mr Requited Moment Resistance*
Wean Roof Height - �r
Roof Slope
15'
20'
26'
30'
40'
2:12
34.4
36.5
38.2
39.7
42.2
3:12
32.2
34.4
36.0
37.4
39.8
4:12
30.4
32.2
33.8
35.1
37.3
5 :12
28.4
30.1
31.6
32.8
34.9 '
8:12
26.4
26.0
29.4
30.6
32.4
7:12
24.4
26.9
27.1
26.2
30.0
*Must be used in conjunction with a list of moment based tile systems endorsed by the
Broward County Board of Rules and Appeals.
For Uplift based tile systems use Method 3. Compared the Values for F' with the
values for F, if the F values are greater than or equal to the Fr values, for each
area of the roof, then the tile attachment method is acceptable.
Method 3 "Uplift Based Tile Calculations Per RAS 127"
(P, : _ x I: - = x w: = _1- W _ x cos B.•_ = Fri • F
(P2: - x 1: _ = x w: _ ._) - W: = x cos 0. = Fn'
(P3 : _ x l• _ = _ x w: = _) - W • ,_ a cos 8: _ = Fri' F
-- F'
Where to Obtain Information
Description
S mbol
Where to find
Design Pressure
P1 or P2 or P3
RAS 127 Table I or by an engineering aaal)sis prepared by PE based on ASCE
7
Mean Roof Height
N
Job site
Roof slope
B
Job Site
Aerodynamic Multiplier
b
PtoductAppmal
Restoring Moment due to Gravity
M
FroductAmmal
Attachment Resistance
Mr
Pwdud Approval
Required Moment RcsWance
M
Calculated
Minimum Attachment Resistance
F'
Pmduot
Required Uplift Resistance
F
Calculated
Average Tile Weight
W
Pwdu9tApvrwvaI
Tile Dimensions
1= length
w=widih
Pmduct Appmel
All calculations must be submitted to the Building Official
at the tune of t application.
SECTION 1524
HIGH VELOCITY HURRICANE ZONES REQUIRED OWNERS NOTIFICATION FOR ROOFING
CONSIDERATIONS
1526.1 As it pertains to this section, it is the responsibility of the roofing contractor to provide the owner with
the required roofing permit, and to explain to the owner the content of this section... The provisions of
Chapter 15 of the Florida Budding Code, Budding govern the minimum requirements and standards of the
industry for roofing system installations. Additionally, the following items should be addressed as part of the
agreement between the owner and the contractor_ The owner's initial in the adjacent box indicates that the
item has been explained.
1. Aesthetics - Workmanship: The workmanship provisions of Chapter 15 (High Velocity Hurricane
are for the purpose of providing that the roofing system meets the wind resistance and water intrusion
performance standards. Aesthetics (appearance) issues are not a consideration with respect to
workmanship provisions. Aesthetic issues such as color or architectural appearance, .that are not part of a
zoning code, should be addressed as part of the agreement men the owner and the contractor.
�2. Renalling Wood Decks: When replacing roofing, the existing wood roof deck may have to be
renailed in accordance with the current provisions of Chapter 16 (High Velocity Hurricane Zones) of the
Florida Building Code. (The roof deck is usually concealed prior to removing the existing roof system).
�3. Common Roofs: Common roofs are those which have no visible delineation between
neighboring units (i.e. towns, condominiums, etc.). In buildings with common roofs, the roofing
contractor and/or owner should notify the occupants of acyaoent units of roofing work to be performed.
� 4. Exposed Ceilings: �, open beam ceilings are where the underside of the row
decking
viewed from below. The Duman may wash to maintain the aniitectural appearance; therefore, roofing
nail penetrations of the underside of the decking may not be acceptable. The Fl�ida Building Code
provides the option of maintaining this appearance.
3. Ponding Water. The current roof system and/or deck of the building may not drain well and may
cause water to pond (accumulate) in low- -lying areas of the roof. Ponding can be an indication of structural
distress and may n3quire the review of a professional structural engineer. Ponding may shorten the Irfe
expectancy and performance of the new roofing system. Ponding conditions dlitions may not be evident until the
o ftinal roofing system is removed. Pont ing corX tons should be Corrected.
6.Overflow scupp em (wall outlets): it is required that rainwater flows off so that the roof Is not
led from a build up of water. Perimeter /edge walls or other roof extensions may block this dischmrge
if overflow scuppers (wall outlets) are not provided. It may be necessary to install overflow scuppers in
accordance with the Florida Building Code, Plumbing.
7. Ventilation: Most roof structures should have some ability to vent natural airflow through the
i r of the str umrai assembly (the building its. The existing amount of attic ventilation shall not be
reduces. It may be beneficial to consider additional venting which can result in extending the service life of
the road.
MIAM MIAMI -DARE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF PERM1117ING, ENVIRONMENT, AND REGULATORY AFFAIRS (PERA) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175 -2474
T (786) 315 -2590 F (786) 315 -2599
NOTICE OF ACCEPTANCE (NOA) www.miamidaae.e °o %era
Eagle Roofing Products LLC
1575 East C.R. 470
Sumter ville, FL 33585
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County PERA - Product Control Section to
be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. PERA reserves the right to revoke this
acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to
meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Bel Air, Bel Air Double Eagle, Ponderosa, Ponderosa Double Eagle, Golden Eagle
Low Profile Concrete Tiles
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This revises NOA# 11 -0321.02 and consists of pages 1 through 10.
The submitted documentation was reviewed by Alex Tigera.
i
NOA No.:12-0430.04
Expiration Date: 10/05/16
Approval Date: 08/02/12
Page 1 of 10
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub Category: Roofing Tiles
Material: Concrete
1. SCOPE:
This approves a new roofing system using "Low Profile Concrete Tile" as manufactured by Eagle Roofing
Products LLC in Sumterville, FL and described in Section 2 of this Notice of Acceptance. For locations
where the pressure requirements, as determined by applicable Building Code does not exceed the design
pressure values obtained by calculations in compliance with RAS 127 using the values listed in section 4
herein. The attachment calculations shall be done as a moment based system
2. PRODUCT DESCRIPTION:
Manufactured by
Applicant Dimensions
Bel Air Concrete Tile L= IT'
W= 12'/4"
Thickness =' /2"
Bel Air Double Eagle
Concrete Tile
Ponderosa Concrete Tile
Ponderosa Double Eagle
Concrete Tile
Golden Eagle Concrete
Tile
Trim Pieces
L= IT'
W= 121/4„
Thickness = %Z"
L= IT'
W= 121/4"
Thickness =' /z"
L = 17"
W= 121/4"
Thickness =1 /z"
L =1T'
W= 121/4"
Thickness =1/2"
1= varies
w = varies
varying thickness
Test
Specifications
Product
Description
TAS 112 Flat profile concrete roof tile equipped with two
nail holes. For adhesive set, direct deck or
battened nail -on applications.
TAS 112 Flat profile concrete roof tile equipped with two
nail holes. For adhesive set, direct deck or
battened nail -on applications.
TAS 112 Flat profile concrete roof tile with slate finish
equipped with two nail holes. For adhesive set,
direct deck or battened nail -on applications.
TAS 112 Flat profile concrete roof tile with shake finish
equipped with two nail holes. For adhesive set,
direct deck or battened nail -on applications.
TAS 112 Flat profile concrete roof tile brushed finish
equipped with two nail holes. For adhesive set,
direct deck or battened nail -on applications.
TAS 112 Accessory trim, clay roof pieces for use at hips,
rakes, ridges and valley terminations.
Manufactured for each tile profile.
NOA No.:12- 0430.04
Expiration Date: 10 /05/16
Approval Date: 08/02/12
Page 2 of 10
e
21 EVIDENCE SUBM=D:
Test Agency
Test Identifier
PRI Asphalt Technologies
ERPF -001 -02 -01
Redland Technologies
7161 -03
Appendix III
Redland Technologies
7161 -03
Appendix III
Redland Technologies
7161 -03
Appendix II
Redland Technologies
P0402
Redland Technologies
Redland Technologies
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
Celotex Corporation Testing
Service
Celotex Corporation Testing
Service
Walker Engineering, Inc.
Walker Engineering, Inc.
Letter Dated Aug. 1,
1994
P09647 -01
94-084
25- 7094 -(2, 5, & 8)
25- 7183 -(5 thru 6)
25- 7214 -(l, 5 , & 8)
25- 7487 -2
25- 7496 -(1 & 4)
25 -78046
520109 -1
520111 -4
520191 -1
Calculations
Calculations
Test Name/Report
TAS 112
Static Uplift Testing
TAS 102
Static Uplift Testing
TAS 102(A)
Wind Tunnel Testing
TAS 108 (Nail -On)
Withdrawal Resistance Testing of screw vs.
smooth shank nails
Wind Tunnel Testing
TAS 108 (Nail -On)
Wind-Tunnel Testing
TAS 108 (Mortar Set)
Static Uplift Testing
TAS 101 (Mortar Set)
Static Uplift Testing
TAS 102
Static Uplift Testing
TAS 102
Static Uplift Testing
TAS 102
Static Uplift Testing
TAS 102
Static Uplift Testing
TAS 102
Static Uplift Testing
TAS 102
Static Uplift Testing
TAS 101
Static Uplift Testing
TAS 101
Aerodynamic Multiplier
Restoring Moments Due to Gravity
Date
Aug. 2006
Dec. 1991
Dec. 1991
Dec. 1991
Sept. 1993
Aug. 1994
Aug. 1994
May 1994
Oct. 1994
Feb. 1995
March, 1995
Dec. 1995
Dec. 1995
Sep. 1996
Dec. 1998
March 1999
Sep. 2006
Sep. 2006
NOA No.:12- 0430.04
Expiration Date- 10/05/16
Approval Date: 08/02/12
Page 3 of 10
3. Limirm IONS:
3.1 Fire classification is not part of this acceptance.
3.2 For mortar or adhesive set tile applications, a static field uplift test in accordance with TAS 106 may required,
refer to applicable building code.
3.3 Applicant shall retain the services of a Miami -Dade County Certified Laboratory to perform quarterly test in
accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Building Code Compliance
Office for review.
3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed
section 4.1 herein.
3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated
otherwise by the underlayment material manufacturers published literature.
3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with
applicable building code.
4. INSTALLATION
4.1 Eagle Roofing Products LLC Bel Air, Bel Air Double Eagle, Ponderosa, Golden Eagle, Ponderosa Double Eagle
Flat Concrete Roof Tiles and its components shall be installed in strict compliance with Roofing Application
Standard RAS 118, RAS 119 and RAS 120.
4.2 Data For Attachment Calculations
Table 1: Average Weight (W) and Dimensions (I x w)
Tile Profile
Weight W (lbf)
Length -1(ft)
Width -w (ft)
Bel Air, Bel Air Double Eagle,
11.4
1.42
1.03
Ponderosa, Golden Eagle,
Ponderosa, Golden Eagle,
Ponderosa Double Eagle Flat
Tile
Table 2: Aerodynamic Multipliers - A (ft)
Tile Profile
A (ft)
A (ft)
Batten Application
Direct Deck Application
Bel Air, Bel Air Double Eagle,
0.301
0.278
Ponderosa, Golden Eagle,
Ponderosa Double Eagle Flat Tile
NOA No.:12- 0430.04
ruArn•E courrrr Expiration Date: 10 105/16
Approval Date: 08/02/12
Page 4 of 10
Table 3: Restoring Moments due to Gravity - M9 (ft4bf)
Tile
3 ":12"
4":12"
5 ":12"
6 ":12"
Greater than
Profile
30.9
38.1
17.2
Air Double
Eagle,
7 ":12"
Bel Air, Bel Air
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Double Eagle,
18.2
Deck
2 #8 Screw
Deck
51.7
Deck
Double
Eagle Flat
Tile
Deck
24.3
Deck
Ponderosa,
7.48
7.71
7.37
7.59
7.22
7.44
7.05
7.27
6.86
7.07
Golden Eagle,
31.9
32.2
2 -10d Ring Shank Nails 50.3 65.5 48.3
1. Installation
with a 4" tile headlap and fastemers are located a min. of 2'/2" from head of tile.
Ponderosa
Double Eagle
Flat Tile
Table 4: Attachment Resistance Expressed as a Moment - Mf (ft -lbf)
for Nail -On Systems
Tile
Profile
Fastener Type
Direct Deck
(min 15132" plywood)
Direct Deck
(min. 19132" plywood)
Battens
Bel Air, Bel
2 -10d Ring Shank Nails
30.9
38.1
17.2
Air Double
Eagle,
1 -10d Smooth or Screw
Shank Nail
7.3
9.8
4.9
Ponderosa,
Golden
2 -10d Smooth or Screw
Shank Nails
14.0
18.8
7.4
Eagle,
1 #8 Screw
30.8
30.8
18.2
Ponderosa
2 #8 Screw
51.7
51.7
24.4
Double
Eagle Flat
Tile
1 -10d Smooth or Screw
Shank Nail Field Clip)
24.3
24.3
24.2
1 -10d Smooth or Screw
Shank Nail Eave Clip)
19.0
19.0
22.1
2 -10d Smooth or Screw
Shank Nails Field Clip)
35.5
35.5
34.8
2 -10d Smooth or Screw
Shank Nails Eave Clip)
31.9
31.9
32.2
2 -10d Ring Shank Nails 50.3 65.5 48.3
1. Installation
with a 4" tile headlap and fastemers are located a min. of 2'/2" from head of tile.
�APPROVEDj
NOA No.:12-0430.04
Expiration Date: 10 /05/16
Approval Date: 08/02/12
Page 5 of 10
Table 5: Attachment Resistance Expressed as a Moment Mf (ft4bf)
for Two Patty Adhesive Set Systems
Tile
Tile Application
Minimum Attachment
Profile
Application
Resistance
Bel Air, Bel Air Double Eagle,
Adhesive
31.3
Ponderosa, Golden Eagle, Ponderosa
Ponderosa, Golden Eagle,
3M 2- Component Foam Roof Tile Adhesive AH -160
Double Eagle Flat Tile
Ponderosa Double Eagle Flat
1 See manufactures component approval for installation requirements.
2 Flexible Products Company TileBond Average weight per patty 13.9 grams.
3MTm 2-Component Foam Roof Tile Adhesive AH -160 Average weight per patty 8 grams.
Table 6: Attachment Resistance Expressed as a Moment - Mf (ft -lbf)
for Mortar Set Systems
for Single Patty Adhesive Set Systems
Tile Profile
Tile Application
Minimum Attachment
Application
Resistance
Resistance
Bel Air, Bel Air Double Eagle,
3M 2- Component Foam Roof Tile Adhesive AH -160
118.9
Ponderosa, Golden Eagle,
3M 2- Component Foam Roof Tile Adhesive AH -160
40.4
Ponderosa Double Eagle Flat
Tile
3 Large paddy placement of 45 grams
of PolyProTm.
4 Medium paddy placement of 24 grams of PolyProTm.
Table 7: Attachment Resistance Expressed as a Moment - W (ft-Ibf)
for Mortar Set Systems
Tile
Tile
Attachment
Profile
Application
Resistance
Bel Air, Bel Air Double Eagle, Ponderosa, Golden
Mortar Set
43.9
Eagle, Ponderosa Double Eagle Flat Tile
5 Tile -Tite Roof Tile Mortar.
NOA No.:12- 0430.04
Expiration Date: 10/05/16
Approval Date: 08102/12
Page 6 of 10
5. LABELING:
All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo (See
Detail Below), or following statement: "Miami -Dade County Product Control Approved %
EAGLE�
FLORIDA
BEL AIR, BEL AIR DOUBLE EAGLE, PONDEROSA, GOLDEN EAGLE, PONDEROSA DOUBLE EAGLE
CONCRETE ROOF TILE LABEL, SUMTERVILLE PLANT
(LOCATED ON UNDERSIDE OF TII.E)
6. BumDING PERMIT REQUIREMENTS:
6.1 Application for building permit shall be accompanied by copies of the following:
6.1.1 this Notice of Acceptance.
6.1.2 Any other documents required by Building Official or Applicable building code in order to properly
evaluate the installation of this system.
NOA No.:12- 0430.04
Expiration Date: 10 /05/16
Approval Date: 08/02/12
Page 7 of 10
PROFILE DRAWING
BEL Ant
BEL Ant DOUBLE EAGLE
mo
NOA No.:12-0430.04
Expiration Date: 10/05/16
Approval Date: 08/02/12
Page 8 of 10
�APPROVED�
PONDEROSA
�,m
PONDEROSA DOUBLE EAGLE
NOA No.:12-0430.04
Expiration Dote: 10 /05/16
Approval Date: 08/02/12
Page 9 of 10
�4
GOLDEN EAGLE
END OF THIS ACCEPTANCE
NOA No.:12-0430.04
Expiration Date: 10/05/16
Approval Date: 08/02/12
Page 10 of 10
, 1
1,
KI NHAMI -DARE COUNTY
s
PRODUCT CONTROL SECTION
DEPARTMENT OF PERMITTING, ENVIRONMENT, AND REGULATORY AFFAIRS (PERA) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175 -2474
T (786) 315 -2590 F (786) 315 -2599
NOTICE OF ACCEPTANCE (NOA) eov/uwww.miamldade.era
3M Company
3M Center Building 0220- 05-E-06
St. Paul, MN. 55144 -1000
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County PERA - Product Control Section to
be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to
have this product or material tested for quality assurance purposes. If this product or material fails to perform in
the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately
revoke, modify, or suspend the use of such product or material within their jurisdiction. PERA reserves the right
to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or
material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: 3MTM 2- Component Foam Roof Tile Adhesive AH -160
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This renews and revises NOA# 11- 0124.04 and consists of pages 1 through 7.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 12-0228.18
Expiration Date: 05/10/17
Approval Date: 05/10/12
Page 1 of 7
ROOFING COMPONENT APPROVAL:
Category: Roofing
Sub Category: Roof tile adhesive
Materials: Polyurethane
SCOPE:
This approves 3MTM 2- Component Foam Roof Tile Adhesive AH -160 as manufactured by 3M Company as
described in Section 2 of this Notice of Acceptance. For the locations where the design pressure requirements, as
determined by applicable building code, does not exceed the design pressure values obtained by calculations in
compliance with Roofing Application Standard RAS 127, for use with approved flat, low, and high profile roof tiles
system using 2- Component Foam Roof Tile Adhesive AH -160. Where the attachment calculations are done as a
moment based system for single patty placement, and as an uplift based system for double patty systems
PRODUCTS MANUFACTURED BY APPLICANT:
Product Dimensions Test Product Description
Specifications
3MTM 2- Component Foam N/A TAS 101 Two component polyurethane foam adhesive
Roof Tile Adhesive AH-
160
Foam Dispenser RTF1000 N/A Dispensing Equipment
ProPack® 30 & 100 N/A Dispensing Equipment
PRODUCTS MANUFACTURED BY OTHERS:
Any Miami -Dade County Product Control Accepted Roof Tile Assembly having a current NOA which list moment
resistance values with the use of 2- Component Foam Roof Tile Adhesive AH -160
roof rile adhesive.
MANUFACTURING LOCATION:
Tomball, TX.
PHYSICAL PROPERTIES:
Property Test
Density ASTM D 1622
Compressive Strength ASTM D 1621
Tensile Strength
ASTM D 1623
Water Absorption
ASTM D 2127
Moisture Vapor Transmission
ASTM E 96
Dimensional Stability
ASTM D 2126
Closed Cell Content ASTM D 2856
Results
1.6 lbs. /ft.3
18 PSI Parallel to rise
12 PSI Perpendicular to rise
28 PSI Parallel to rise
0.08 Lbs./Fe
3.1 Perm / Inch
+0.07% Volume Change @ -40° F., 2 weeks
+6.0% Volume Change @158°F.,100% Humidity, 2
weeks
86%
NOA No.: 12- 0228.18
Expiration Date: 05/10/17
Approval Date: 05/10/12
Page 2 of 7
� • 1
Note: The physical properties listed above are presented as typical average values as determined
by accepted ASTM test methods and are subject to normal manufacturing variation.
EVIDENCE SUBMITTED:
Test Aaencv
Test Identifier
Test Name/Report
Date
Center for Applied Engineering
#94 -060
TAS 101
04/08/94
257818 -IPA
TAS 101
12/16/96
Trinity Engineering
25- 7438 -3
SSTD 11 -93
10/25/95
Celotex Corp. Testing Services
25 -7438-4
TAS 101
10/23/98
25- 7438 -7
SSTD 11 -93
11/02/95
25 -7492
SSTD 11 -93
12/12/95
Miles Laboratories
NB -589 -631
ASTM D 1623
02/01/94
Polymers Division
Ramtech Laboratories, Inc.
9637 -92
ASTM E 108
04/30/93
Southwest Research Institute
01- 6743 -011
ASTM E 108
11/16/94
01- 6739- 062b[l]
ASTM E 84
01/16/95
Trinity Engineering
7050.02.96 -1
TAS 114
03/14/96
Celotex Corp. Testing Services
528454 -2 -1
TAS 101
10/23/98
528454 -9 -1
528454 -10 -1
520109 -1
TAS 101
12/28/98
520109 -2
520109 -3
520109 -6
520109 -7
520191 -1
TAS 101
03/02/99
520109 -2 -1
LIMITATIONS:
1. Fire classification is not part of this acceptance. Refer to the Prepared Roof Tile Assembly for fire rating.
2. 3MTM 2- Component Foam Roof Tile Adhesive AH -160 shall solely be used with flat, low, & high tile profiles.
3. Minimum underlayment shall be in compliance with the Roofing Application Standard RAS 120.
4. Roof Tile manufactures acquiring acceptance for the use of 3MTM 2- Component Foam Roof Tile Adhesive AH-
160 roof tile adhesive with their tile assemblies shall test in accordance with TAS 101.
5. Roof Tile manufactures acquiring acceptance for the use of HANDI -STICK roof tile adhesive with their file
assemblies shall test in accordance with TAS 101 with section 10.4 as modified herein.
F W
2
F'=
MS
NOA No.: 12-0228.18
Expiration Date: 05/10/17
Approval Date: 05/10/12
Page 3 of 7
INSTALLATION:
1. 3MTM 2- Component Foam Roof Tile Adhesive AH -160 may be used with any roof tile assembly having a current
NOA that lists uplift resistance values with the use of 3MTM 2- Component Foam Roof Tile Adhesive AH -160.
2. 3MTM 2- Component Foam Roof Tile Adhesive AH -160 shall be applied in compliance with the Component
Application section and the corresponding Placement Details noted herein. The roof tile assembly's adhesive
attachment with the use of 3MTM 2- Component Foam Roof Tile Adhesive AH -160 shall provide sufficient
attachment resistance, expressed as an uplift based system, to meet or exceed the uplift resistance determined in
compliance with Miami -Dade County Roofing Application Standards RAS 127. The adhesive attachment data is
noted in the roof tile assembly NOA.
3. 3MTM 2- Component Foam Roof Tile Adhesive AH -160 and its components shall be installed in accordance with
Roofing Application Standard RAS 120, and 3M Company's 3MTM 2- Component Foam Roof Tile Adhesive AH-
160 Operating Instruction and Maintenance Booklet.
4. Installation must be by a Factory Trained'Qualified Applicator' approved and licensed by 3M Company. 3M
Company shall supply a list of approved applicators to the authority having jurisdiction.
5. Calibration of the Foam Dispenser RTF 1000 dispensing equipment is required before application of any adhesive.
The mix ratio between the "A" component and the "B" component shall be maintained between 1.0 -1.15 (A): 1.0
(B). The dispense timer shall beset to deliver 0.0175 to 0.15 pounds per tile as determined at calibration. No
other settings shall be approved.
6. 3MTM 2- Component Foam Roof Tile Adhesive AH -160 shall be applied with Foam Dispenser RTF1000 or
ProPack® 30 & 100 dispensing equipment only.
7. 3MTM 2- Component Foam Roof Tile Adhesive AH -160 shall not be exposed permanently to sunlight.
8. Tiles must be adhered in freshly applied adhesive. Tile must be set within 2 to 3 minutes after 3MTM 2-
Component Foam Roof Tile Adhesive AH -160 has been dispensed.
9. 3MTM 2- Component Foam Roof Tile Adhesive AH -160 placement and minimum patty weight shall be in
accordance with the Placement Details' herein. Each generic tile profile requires the specific placement noted
herein.
Table 1: Adhesive Placement For Each Generic Tile Profile
Tile Profile
Placement Detail
Single Paddy Weight
Min. (grams)
Two Paddy Weight per
paddy Min. (grams)
Flat, Low, High Profiles
#1
35
N/A
lhgh Profile 2 Piece Banrel
#1
17 /side on cap and 34/ an
N/A
Flat, Low, High Profiles
1 #2
24
N/A
Flat, Low, Ifigh Profiles
1 #3
8
APPROVED
NOA No.: 12- 0228.18
Expiration Date: 05 /10/17
Approval Date: 05/10/12
Page 4 of 7
LABELING:
All 3MTm 2-Component Foam Roof Tile Adhesive AH-160 containers shall comply with the Standard Conditions
listed herein.
BUILDING PERmrr REQumEN[ENTs:
As required by the Building Official or applicable building code in order to properly evaluate the installation of this
system.
ADHESIVE PLACEMENT DETAIL 1
SINGLE PATTY
HandmophdCafflMd
1
io
Fasda
Em ca m a*.
EM Cbm
Keepagedo4p-
4hLupfmmw9qftW
ffil
NOA No.: 12-0228.18
Expiration Date: 05/10/17
Approval Date: 05/10/12
Page 5 of 7
ADHESIVE PLACEMENT DETAIL 2
SINGLE PATTY
............. . . . . . .
........ . . . . .
NOA No.: 1241228.18
anAOE coin Expiration Date: 05/10/17
Approval Date: 05/10/12
Page 6 of 7
ADHESIVE PLACEMENT DETAIL 3
DOUBLE PATTY
Nap through PWftW=m Nap through pbefic
UndwWymed
(under file)
Nap Vmgh pWft cement S419 Fe"
under We mile Paft
\ between tHe
1 'D hLx3bL
,23- 4
sn& Ps"
on undeftmed
END OF THIS ACCEPTANCE
sWgI9 PW under tne
Shopa*betweentle
2 hL x7 bL modkim
size pa* sm
cowse only
T FeWs
�, y1seph*
m damns
DOedp
NOA No.: 12-0228.18
Expiration Date: 05/10/17
Approval Date: 05/10/12
Page 7 of 7
4,004 2r, 0021 "
M-17710�,
Nap Vmgh pWft cement S419 Fe"
under We mile Paft
\ between tHe
1 'D hLx3bL
,23- 4
sn& Ps"
on undeftmed
END OF THIS ACCEPTANCE
sWgI9 PW under tne
Shopa*betweentle
2 hL x7 bL modkim
size pa* sm
cowse only
T FeWs
�, y1seph*
m damns
DOedp
NOA No.: 12-0228.18
Expiration Date: 05/10/17
Approval Date: 05/10/12
Page 7 of 7
F+Ilillrl
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
11805 SW 26 Street, Room 208
BOARD AND CODE ADNIMSTRATION DIVISION
Miami, Florida 33175 -2474
T (786) 315 -2590 F (786) 315 -2599
NOTICE OF ACCEPTANCE (NOA)
www.miamidadexov /economy
Polyglass USA Inc.
150 Lyon Drive
Fernley, NV 89408
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Polystick Underlayments
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This revises NOA #11- 1229.01 and consists of pages 1 through 8.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 12-0713.02
Expiration Date: 09/13/16
Approval Date: 02/14/13
Page 1 of 8
ROOFING COMPONENT APPROVAL
Cateaorv: Roofing
Sub - Category: Underlayment
Material: SBS , APP Self - Adhering Modified Bitumen
PRODUCTS DESCRIPTION:
Polystick Tile Pro Roll: TAS 103 and A rubberized asphalt self-adhering, glass -
Manufacturing Location 61' x 3'3 -3/8" ASTM D 1970 fiber /polyester reinforced waterproofing
#2 60 mils thick membrane. Designed as a metal roofing and roof
tile underlayment.
Polystick Dual Pro Roll: TAS 103 and A rubberized asphalt self-adhering, glass -
Manufacturing Location 61' x 3'3 3/8" ASTM D 1970 fiber /polyester reinforced waterproofing
#2 60 mils thick membrane. Designed as a metal roofing and
roof tile underlayment.
NOA No.: 12-0713.02
Expiration Date: 09/13/16
Approval Date: 02/14/13
Page 2 of 8
Test
Product
Product
Dimensions
Specification
Description
Polystick MTS
Roll:
TAS 103
A homogeneous, rubberized asphalt
underlayment
6558" x 3'3 3/8"
waterproofing membrane, glass fiber reinforced
Manufacturing Location
60 mils thick
with polyolefinic film on the upper surface for
#2
use as an underlayment for metal roofing, roof
tile, slate tiles and shingle underlayment.
Polystick IR Xe
Roll:
TAS 103 and
A fine granular /sand top surface self-adhering,
underlayment
65' x 3'3-'/g"
ASTM D 1970
APP polymer modified, fiberglass reinforced,
Manufacturing Location
Or 65' x 3'
bituminous sheet material for use as an
#1 & #2
60 mils thick
underlayment in sloped roof assemblies.
Designed as an ice & rain shield and as a flat
roof tile underlayment.
Polystick TU
Roll:
TAS 103 and
A heavy granuled surface self adhering, APP
underlayment
32'10" x 3'3 3 /g'
ASTM D 1970
polymer modified, fiberglass or polyester
Manufacturing Location
100 mils thick
reinforced, bituminous sheet material for use as
#1 & #2
an underlayment in sloped roof assemblies.
Designed as a a roof file underlayment.
Polystick TU Plus
Roll:
TAS 103 and
A rubberized asphalt self - adhering, glass -
underlayment
65' x 3'3j/8"
ASTM D 1970
fiber /polyester reinforced waterproofing
(Surface Printing)
80 mils thick
membrane. Designed as a metal roofing and roof
Manufacturing Location
tile underlayment.
#1 & #2
Polystick TU P
Roll:
TAS 103 and
A rubberized asphalt waterproofing membrane,
underlayment
32'10" x 3'3j/8"
ASTM D 1970
glass- fiber /polyester reinforced, with a granular
Manufacturing Location
130 mils thick
surface designed for use as a tile roof
#2
underlayment.
Polystick Tile Pro Roll: TAS 103 and A rubberized asphalt self-adhering, glass -
Manufacturing Location 61' x 3'3 -3/8" ASTM D 1970 fiber /polyester reinforced waterproofing
#2 60 mils thick membrane. Designed as a metal roofing and roof
tile underlayment.
Polystick Dual Pro Roll: TAS 103 and A rubberized asphalt self-adhering, glass -
Manufacturing Location 61' x 3'3 3/8" ASTM D 1970 fiber /polyester reinforced waterproofing
#2 60 mils thick membrane. Designed as a metal roofing and
roof tile underlayment.
NOA No.: 12-0713.02
Expiration Date: 09/13/16
Approval Date: 02/14/13
Page 2 of 8
PRODUCTS DESCRIPTION:
Test Product
Product Dimensions Specification Description
Polystick TU Max Roll: TAS 103 and A rubberized asphalt self - adhering, polyester
Manufacturing Location 65'8"x3'3-3/8" ASTM D 1970 reinforced waterproofing membrane. Designed
#2 60 mils thick as a a roof file underlayment.
MANUFACTURING PLANTS:
1.Hazelton, PA
2.Winter Haven, FL
EVIDENCE SUBNHTTED:
Test Aaencv
Test Identifier
Test Name/Report
Date
Exterior Research & Design, LLC
11756.04.01 -1
TAS 103
04/27/01
11756.08.01 -1
ASTM D 1970
08/14/01
02202.08.05
TAS 103
08/29/05
Trinity I ERD
P5110.08.07
TAS 103
08/29/07
P10870.09.08 -R1
TAS 103
12/04/08
P10870.04.09
TAS 103 /ASTM D4798 & G155
04/13/09
P33360.06.10
ASTM D1970
07/01/10
P33370.03.11
TAS 103
03/02/11
P33370.04.11
ASTM D 1623
04/26/11
P36900.09.11
TAS 103 /ASTM D4798 & G155
09/01/11
P37300.10.11
TAS 110 /ASTM D4798 & D1970
10/19/11
P40390.08.12 -1
TAS 103 & TAS 110
08/06/12
P40390.08.12 -2
ASTM D 1623
08/07/12
P40390.10.12
ASTM D 1970
10/03/12
PRI Asphalt Technologies
PRI01111
ASTM D 4977
04/08/02
PUSA- 005 -02 -01
ASTM D 4977
01/31/02
PUSA - 018 -02 -01
ASTM D 2523
07/14/03
PUSA- 035 -02 -01
TAS 103
09/29/06
PUSA - 033 -02 -01
ASTM D 1970
01/12/06
PUSA- 055 -02 -02
TAS 103
12/10/07
PUSA -083 -02 -01
TAS 103
06/30/08
PUSA - 089 -02 -01
TAS 103 /ASTM D4798 & G155
07/06/09
Momentum Technologies, Inc.
JX20H7A
TAS 103 /ASTM D4798 & G155
04/01/08
RX14E8A
TAS 103 /ASTM D4798 & G155
11/09/09
DX23D8B
TAS 103 /ASTM D4798 & G155
02/18/10
DX23D8A
TAS 103 /ASTM D4798 & G155
02/18/10
NOA No.: 12-0713.02
Expiration Date: 09/13/16
Approval Date: 02/14/13
Paae 3 of 8
INSTALLATION PROCEDURES:
Deck Type 1: Wood, non - insulated
Base Sheet: One or more plies of ASTM D 226 Type H or ASTM D 2626.
Fastening: Per FBC 1518.2 & 1518.4 Nails and tin caps 12" grid, 6" o.c. at a minimum 4" head lap. (for
base sheet only)
Membrane: Polystick membranes self- adhered.
Surfacing: None
1. All nails in the deck shall be carefully checked for protruding heads. Re- fasten any loose decking panels,
and sweep the deck thoroughly to remove any dust and debris prior to application.
2. Place the underlayment over metal drip edge in accordance with RAS 111.
3. Place the first course of membrane parallel to the eave, rolling the membrane to obtain maximum contact.
Remove the release film as the membrane is applied.. All side laps shall be a minimum of 3-1/2" and end
laps shall be a minimum of 6." Roll the membrane into place after removing the release strip. Vertical
strapping of the roof with Polystick is acceptable. Membrane shall be back nailed in accordance with
applicable building code.
4. When applying the membrane in the valley, start at the low point and work to the high point, rolling the
membrane from the center outward in both directions.
5. For ridge applications, center the membrane and roll from the center outward in both directions.
6. Roll or broom the entire membrane surface so as to have full contact with the surface, giving special
attention to lap areas.
7. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product
Control Notice of Acceptance.
8. All protrusions or drains shall be initially taped with a 6" piece of underlayment. The flashing tape shall be
pressed in place and formed around the protrusion to ensure a tight fit. A second layer of Polystick shall be
applied over the underlayment.
NOA No.: 12-0713.02
r7ary7'nA7e aT, Expiration Date: 09/13/16
Approval Date: 02/14113
Page 4 of 8
GENERAL LEmnATIONS:
1. Fire classification is not part of this acceptance.
2. Polystick MTS, TU Plus, Tile Pro and Dual Pro may be used in asphaltic shingles, wood shakes and shingles,
non - structural metal roofing, roof tile systems and quarry slate roof assemblies. Polystick IR -Xe, TU, and TU
P may be used in all the previous assemblies listed except metal roofing. Polystick TU Max may be used in
roof tile systems only.
3. Deck requirements shall be in compliance with applicable building code.
4. Polyglass Polystick membranes shall be applied to a smooth, clean and dry surface. The deck shall be free of
irregularities.
5. Polyglass Polystick membranes and underlayments shall not be adhered directly over a pre- existing roof
membrane as a recover system.
6. Polyglass Polystick membranes shall not be left exposed as a temporary roof for longer than the amount of
days listed in the table below after application. Polyglass reserves the right to revise or alter product
exposure times; not to exceed the preceeding maximum time limitations.
Exposure Limitations (days)
Polystick MTS
MTS
IR-Xe
TU
TU Plus
TU P
Tile Pro
Dual Pro
TU Max
Winter Have AFL
180
180
180
180
180
180
180
90
Hazelto PA.
N/A
30
1 30
180
N/A
N/A
N/A
N/A
7. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code
and Rule 9N -3 of the Florida Administrative Code.
8. In roof file application, data for the attachment resistance of roof tiles shall be as set forth in the roof tie
manufacturer's Notice of Acceptance. Polystick TU, TU Plus, Tile Pro and TU Max may be used in both
adhesive set and mechanically fastened roof tile applications. Polystick IR Xe, and Dual Pro are limited to
mechanically fastened roof file applications. Polystick MTS is limited to mechanically fastened with battens
roof tile applications. Polystick TU P may be used in both adhesive set and mechanically fastened roof tile
applications with the exception of mortar set tile applications.
9. The maximum roof slope for use as roof file underlayment for (direct -to -deck) tile assemblies shall be as
follows: (See Table Below)
Tile Profile
Polystick MTS
Polystick IR-Xe
Polystick TU, TU
Polystick TU
Plus, TU P, Tile
Max
Pro
Flat Tile
Prohibited without
5:12
No limitation
No limitation
battens
Profiled Tile
Prohibited without
Prohibited
No limitation
No limitation
battens
The above slope limitations can be exceeded only by using battens and counter battens in accordance with the
Approved Tile System Notice of Acceptance and applicable Florida Building Code requirements. Battens
are required for both loading and installation of tiles at all times.
NOA No.: 12-0713.02
Expiration Date: 09/13/16
Approval Date: 02114/13
Page 5 of 8
GENERAL LIMITATION5: (CONTINUED
10. Care should be taken during the loading procedure to keep foot traffic to a minimum and to avoid dropping of
tile directly on the underlayment. Refer to Polyglass' Tile loading detail below for loading procedure for all
underlayments except Polystick MTS which shall be loaded onto battens.
0
Q
0
n
:v
t
a ��w
I
t3ot UecK preparea vmm
POLYS 1CKTU PWs
11. Refer to prepared roofing system Product Control Notice of Acceptance for listed approval of this product
with specific prepared roofing products. Polystick MTS, IR Xe, TU, TU Plus, TU P, TU Max, Dual Pro and
Tile Pro may be used with any approved roof covering Notice of Acceptance listing Polystick MTS, IR-Xe,
TU, TU Plus, TU P, TU Max, Dual Pro and Tile Pro as a component part of an assembly in the Notice of
Acceptance. If Polystick MTS, IR Xe, TU, TU Plus, TU P, TU Max, Dual Pro and Tile Pro is not listed, a
request may be made to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control
Department for approval provided that appropriate documentation is provided to detail compatibility of the
products, wind uplift resistance, and fire testing results.
LABELING:
1. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo,
city and state of manufacturing facility and the following statement: "Miami -Dade County Product Control
Approved" or the Miami -Dade County Product Control Seal as shown below.
MII4MI•9►DE N-6-4 1
• 1
BUILDING PERMIT REQUIREMENTS:
Application for building permit shall be accompanied by copies of the following:
1. This Notice of Acceptance.
2. Any other documents required by the Building Official or applicable building code in order to properly evaluate
the installation of this materials.
NOA No.: 12-0713.02
Expiration Date: 09 /13/16
Approval Date: 02/14/13
Page 6 of 8
POLYGLASS GENERAL APPLICATION GUIDELINES FOR POLYSTICK MEMBRANES:
1. Polyglass does accept the direct application of Polystick underlayment membranes to wood decks. Installers
are cautioned to refer to applicable local building codes prior to direct deck installation to ensure this is
acceptable. Please also refer to applicable Product Data Sheets of the corresponding products.
2. All rolls, with the exception of Polystick TU Plus should be back-nailed in selvage edge seam as per Polyglass
Back Nailing Guide. Nails shall be, 11 gauge ring shank type, applied with a minimum 1" metal disk as
required in Dade County or simplex type nail as otherwise allowable in other regions, at a minimum rate of
12" o.c. Polystick TU Plus should be back nailed in designated area marked "nail area, area para clavar" on
the face of membrane, with the above stated nails and/or disks. The head lap membrane is to cover the area
being back-nailed. (Please refer to applicable local building codes prior to installation.)
3. All seal lap seams (selvage laps) must be rolled with a hand roller to ensure full contact.
4. All fabric over fabric; and granule over granule end laps, shall have a 6" wide, uniform layer of Polyglass
Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement,
Polyglass PG500 MB Flashing Cement, applied in between the application of the lap. The use of mastic
between the laps does not apply to Polystick MTS.
5. A maximum of 6 tiles per stack are allowed when loading tile on the underlayments. Refer to the Polyglass
Tile Loading Guidelines. See General Limitations #9 and #10.
6. Battens and/or Counter - battens, as required by the tile manufacturers NOA's, must be used on all projects for
pitch/slopes of 7"/12" or greater. It is suggested that on pitch/slopes in excess of 6'/4 "/12 ", precautions
should be taken, such as the use of battens to prevent tile sliding during the loading process.
7. Minimum cure time after membrane installation & before loading of roofing tiles is Forty-Eight (48) Hours.
8. Polystick membranes may not be used in any exposed application such as crickets, exposed valleys, or
exposed roof to wall details.
9. Repair of Polystick membranes is to be accomplished by applying Polyglass Polyplus 55 Premium Modified
Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, Polyglass PG500 MB Flashing
Cement to the area in need of repair, followed by a patch of the Polystick material of like kind should be set
and hand rolled in place over the area needing such repair. Patching membrane shall be a minimum of 6
inches in either direction. The repair should be installed in such a way so that water will run parallel to or
over the top of all laps of the patch.
10. All self - adhered membranes must be rolled to ensure full contact with approved substrates. Polyglass
requires a minimum of 40 lbs for a weighted roller for the rolling of the field membrane. Hand rollers are
acceptable for rolling of patches or small areas of the roof. Brooming may be used where slope prohibits
rolling.
11. All approved substrates should be dry, clean and properly prepared, before any application of Polystick
membranes commences. An approved substrate technical bulletin can be furnished upon request. It is
recommended to refer to applicable building codes prior to installation to verify acceptable substrates.
12. The Polyglass Miami -Dade Notice of Acceptance (NOA) approval for Polystick membranes and
PolyProtector UDL can be furnished upon request by our Technical Services Department by calling 1 (800)
894 -4563.
NOA No.: 12- 0713.02
Expiration Date: 09/13/16
Approval Date: 02/14/13
Pace 7 of
V
13. Questions in regards to the application of Polyglass products should be directed to our Technical Services
Department at 1 (800) 894 -4563.
14. Polyglass recommends that applicators follow good roofing practices and applicable procedures as outlined
by the National Roofing Contractors Association (NRCA).
PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC
APPLICATIONS. LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND
RECOMMENDATIONS.
END OF THIS ACCEPTANCE
NOA No.: 12-0713.02
Expiration Date:, 09/13/16
Approval Date: 02/14/13
Paae 8 of 8