Loading...
RF-12-1022Inspection Worksheet Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL Phone: (305)795 -2204 Fax: (305)756 -8972 Inspection Number: INSP- 177051 Permit Number: RF -6 -12 -1022 Scheduled Inspection Date: August 08, 2012 Inspector: Bruhn, Norman Owner: PAULSON, ROBERT Job Address: 10205 NE 4 Avenue Miami Shores, FL Project: <NONE> Contractor: QUALITY ROOFING CONTRACTORS INC Permit Type: Roof Inspection Type: Final Roof Work Classification: Flat Phone Number (305)751 -8593 Parcel Number 1132060170770 Phone: (305)953 -3333 Building Department Comments RE ROOF TO A NEW FLAT MINERAL CAP SHEET ROOF WITH 1/2 INCH INSULATION BOARD. Failed Correction Needed Re- Inspection Fee No Additional Inspections can be scheduled until re- inspection fee is paid. Inspector Comments CREATED AS REINSPECTION FOR INSP- 176935. CREATED AS REINSPECTION FOR INSP- 174425. Cancelled by Mary. C_— August 07, 2012 For Inspections please call: (305)762 -4949 Page 21 of 33 RE: Permit# RF -6 -12 -1022 Miami Shores Village Building Department 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 DATE: June 25, 2 01 2 INSPECTION AFFIDAVIT Carlos Arocho licensed as a (n) Contractor / Engineer / Architect, (Print name and drde License Type) License #: 0 0 0 01 7 8 8 9 On or about June 2 6 , 2 012 (Date & time) Secondary water barrier work at 10205 N.E. FS 468 Building Inspector , I did personally inspect the roof deck nailing and 4 Avenue (Complete Job Site Address) Based upon that examination I have determined the installation was done according to the Hurricane Mitigation Retrofit Manual (Based on 553.844 F.S) Signature State of Florida County of Dade: The undersigned, being the first duly swom, deposes and says that he /she is the contractor for the above property mentioned. Swom to and subscribed before me this o2 C, day Notary Public, Sate of Florida at Large NOTARY PUBLIC -STATE OF FLORIDA Marylou Hernandez Commission #DD930046 „;,.s Expires: OCT. 10, 2013 BONDED THRU ATLANTIC BOYDING CO., INC. an inspection. Include photographs of each plane of the roof with `General, Building, Residential, or Roofing Contractors or any individual certified under 468 F.S. to make su permit # and address # dearly shown marked on the deck for each inspection Revised on 5/21/2009 NOTICE OF COMMENCEMENT A RECORDED COPY MUST BE POSTED ON TBE JOB SITE Al' TIME OF FIRST INSPECTION • PERMIT NO. TAX FOLIO NO. -3206-017-0770 STATE OF FLORIDA: COUNTY OF MIAMI -DADE: THE UNDERSIGNED hereby gives notice that improvements will be made to certain real property, and in accordance with Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement. 11111 11111 11111111 1111 11111111111111 FN 2012R0393601 OR f k 28135 Ps 4139; tips) RECORDED 06/015/2012 09:17:03 HARVEY RiJVIN, CLERK OF COURT MIAMI -DADE COUNTY, FLORIDA LAST PAGE 1. Legal description of property and street/address: 10205 N . E . 4th Avenue Miami Shores, Florida 33138 2. Description of improvement: Reroof to a new Flat Mineral Cap sheet roof. 3. Owner(s) name and address: Robert O. Paulson Interest in property: Owner 10205 N.E. 4th Avenue Miami Shores, Fl 33138 Name and address of fee simple titleholder: N/A 4. Contractor's name and address: Quality Roofing Contractor, Inc. 13800 N.W. 1st Avenue Miami, F1 331 68 5. Surety: (Payment bond required by owner from contractor, if any) Name and address: N/A Amount of bond $ 00 6. Lender's name and address: N/A 7. Persons within the state of Florida designated by Ow provided by Section 713.13(1)(a)7., Florida Statutes, Name and address: N/A S E OF FLORIDA, COUNTY OF DADE !HEREBY CERTIFY that t s a true soy o 1 ifitroZnoticeA . m'y nd and Ca,ola CLERK, of Cir_ r document - r%ay,,�k rsty COUO3 ra.O. ra 8. In addition to himself, idles the following person(s) to receive a copy of the Lienor's Notice as provided in Section 713.13(1)(b), Florida Statutes. Name and address: N/A 9.. Expiration date of this Notice of Commencement: (the expiration different date is specified) Signature 9.1 er date is 1 year from the date of recording unless a Print Owner's Name)e ,% 7fy JX'IJe Sworn to and subscribed before me this v (0, day of Notary Public �' yl 1,..r Print Notary's Name / NOTARY PUBLIC-STATE OFFL[ IA My commission expires: ,'" "• arylou Hernandez ,�s d Commission #DD930046. ;,J Expires: OCT. 10, 2013 BONDED THRII ATLANTIC BONDfl G CO, INC. 123.W -52 PAGE 4 1 O/04 Prepared byMarylou Hernandez 20 . Quality Roofing Contraci Address:13800 N.W. 1st Avenue Miami, Fl 33168 (305) 953 -3333 1. ("e.g. .1- Miami Shores Village Building Department 10050 N.E.2nd Avenue, Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 INSPECTION'S PHONE NUMBER: (305) 762.4949 BUILDING PERMIT APPLICATION Permit Type: BUILDING JOB ADDRESS: 10205 N. E. 4th Avenue 111 TggMEWE JUN 0 2612 BY: FTIC20 Permit No. InC 10 Master Permit No. City: Miami Shores Folio/Parcel #: 1 1- 3206 - 017 -0770 Is the Building Historically Designated: Yes County: Miami Dade Zip: 33138 NO x Flood Zone: OWNER: Name (Fee Simple Titleholder): Robert 0. Paulson Phone#: (305)751-8593 Address: 10205 N.E. • 4th Avenue City: Miami Shores Tenant/Lessee Name: State: Fl zip: 3 31 3 8 Phone#: Email: CONTRACTOR: Company Name:Quality Roofing Contractor, Inc.phone#: (305) 953 -3333 Address: 13800 N.W. 1st Avenue City: Miami State: Fl Zip: 33168 Qualifier Name: Carlos Arocho Phone#: ( 786) 367 -2029 State Certification or Registration #: RC 0 0 5 8 6 2 7 Certificate of Competency #: 0 0 0 01 7 8 8 9 Contact Phone #: (305) 953 -3333 Email Address: qualityroofing88 @yahoo.com DESIGNER: Architect/Engineer: Phone#: Value of Work for this Permit: $ 8 , 0 0 0 .0 0 Square/Linear Footage of Work: 4 0 0 s q f t . Type of Work: DAddition OAlteration ONew Description of Work: Reroof to a new Flat Mineral insulation board. XIRepair/Replace ODemolition cap sheet roof with 1/2 inch Color thru tile: ***** * * * * * * * * * * * * * * * * * * ** * * * * * * * * * ** Submittal Fee $ Permit Fee $ Scanning Fee $ Radon Fee $ ** Fees************* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** SlJ oc-1 CCF $ CO /CC $ DBPR $ Bond $ Notary $ Training/Education Fee $ Technology Fee $ Double Fee $ Structural Review $ TOTAL FEE NOW DUE $ d 3:q .6 Bonding Company's Name (if applicable) Bonding Company's Address City State Zip Mortgage Lender's Name (if applicable) Mortgage Lender's Address City State Zip Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be secured for Fi.RCTRICAL WORK, PLUMBING, SIGNS, WELLS, POOLS, FURNACES, BOILERS, HEATERS, TANKS and AIR CONDITIONERS, ETC OWNER'S Ak 'DAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. "WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT." Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must promise in good faith that a copy of the notice of commencement and construction lien law brochure will be delivered to the person whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site for the first inspection which occurs seven (7) days after the building permit is issued. In the absence of such posted notice, the inspection will not be approved and a reinspection fee will be charged. Signature NO 3 ,,r.' Owner or Agent Contractor The foregoing instrument was acknowledged before me this .?% The foregoing instrument was acknowledged before me this gte day of , 20I ±, by 13.4 day of i4t..� ll , 20 Q?- t. , by a i ors ®c.�,L * who is personally y known to me or who has produced who is personalll known to me or who has produced As identification and who did take an oath. as identification and who did take an oath. NOTARY PUBLIC: / NOTARY PUBLIC: Signature Sign: 121/6-- < Sign: / Print: Print: NOTARY PUBLIC•STAT F FLORIDA My Commission Expires " 1 ',. Marylou Hernandez t. 4;, I Commission #DD930046 ,,,,,,;,.` Expires: OCT. 10, 2013 MUD MU ATLANTIC BONDING CO., INC. B*************** ********yyR* pia** B******************************# #***************** *****+i<+i ****************M **** My Commission Expii' Mar 1011 Hernandez Commission #DD930046 J Expires: OCT. 10, 2013 BONDED THRL' ATLANTIC BOYDING CO., INC. APPROVED BY 6'(01- Plans Examiner Zoning Structural Review Clerk (Revised 3 /12/2012)(Revised 07 /10 /07)(Revised 06/10/2009)(Revised 3/15/09) Miami Shores Village Building Department 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 OWNERS'S AFFIDAVIT OF EXEMPTION ROOF TO WALL CONNECTION HURRICANE MITIGATION RETROFIT FOR EXISTING SITE - BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES PERSUANT TO SECTION 553.844 F.S. To: Miami Shores Village Building Department Date: 5 / 2 6 / 12 10050 NE 2nd Ave Miami Shores, Fl 33138 Re: Owner's Name: Robert 0. & Betty Paulson Property Address: 10 2 0 5 N .E . 4th Avenue Miami Shores, Fl 33138 Roofing Permit Number: Dear Building Official: 1 Robert 0. Paul son certify that I am not required to retrofit the roof to wall connections of my building because: q(The just valuation for the structure for purpose of ad valorem taxation is less than $300,000.00. Please attach proof of ad valorem taxation. o The building was constructed in compliance with the provisions of the Florida Building Code (FBC) or with the provisions of 1994 edition of the South Florida Building Code (1994 SFBC) Leeer.4._ Signature &L) "sox/ Print Name State of Florida County of Dade The undersigned, being the first duly swom, deposes and says that he /she is the owner for the above property mentioned. Swom to and subscribed before me this day •f ti(av 0/0/,) `// NOTARY PUBLIGSTATE OF FLORIDA Marylou Hernandez Notary Public, Sate of Florida at Large � � - �n� Commission #DD930046 ry g �� Expires: OCT. 10, 2013 BONDED THRU ATLANTIC BONDING CO., INC. • When the just valuation of the structure for purpose of ad valorem taxation is equal to or more th f $300,000.00, and the building was not constructed with FBC nor a 1994 SFBC. Then you must provide a building application from a General Contractor for the Roof to Wall connection Hurricane Mitigation. Revised on 5/21/2009 Property Information Map My Home Miami -Dade County, Florida Page 1 of 1 Property Information Map Aerial Photography - 2009 0 28 ft This map was created on 5/26/2012 9:45:07 AM for reference purposes only. Web Site © 2002 Miami -Dade County. All rights reserved. Summary Details: Folio No.: 11- 3206 - 017 -0770 Property: 10205 NE 4 AVE Mailing ROBERT 0 PAULSON JR Address: &W BETTY Living Units: 10205 NE 4 AVE MIAMI FL Adj Sq Footage: 33138 -2416 Property Information: Primary Zone: 1000 SINGLE FAMILY RESIDENCE CLUC: 0001 RESIDENTIAL - SINGLE FAMILY Beds/Baths: 2/1 Floors: 1 Living Units: 1 Adj Sq Footage: 2,048 Lot Size: 8,850 SQ FT Year Built: 1939 $50,000/ $65,821 AMD PL OF MIAMI City: SHORES SEC 4 LOT 13 Legal & W1/2 OF LOT 14 BLK Description: 92 PB 15 -14 LOT SIZE 75.000 X 118 OR 10771 - 101701806OR10771- 1017 0180 03 Assessment Information: Year: 2011 2010 Land Value: $110,206 $137,577 Building Value: $155,786 $155,786 Market Value: $265,992 $293,363 Assessed Value: $115,821 $114,110 Exemption Information: Year: 2011 2010 Homestead: $25,000 $25,000 2nd Homestead: YES YES Taxable Value Information: Year: 2011 2010 $55,000 Applied ' Applied Taxing Authority: Exemption/ Taxable Exemption/ Taxable Other disqualified Value: Value: Regional: $50,000/ $65,821 $50,000/ $64,110 County: $50,000/ $65,821 $50,000/ $64,110 City: $50,000/ $65,821 $50,000/ $64,110 School Board: $25,000/ $90,821 $25,000/ $89,110 Sale Information: Sale Date: 1/1980 Sale Amount: $55,000 Sale O /R: 10771 -1017 Sales Qualification Other disqualified Description: View Additional Sales http: / /gisims2 .miamidade.gov /myhome /printmap. asp? mapurl= http: / /gisims2.miamidade.go... 5/26/2012 ROOF ASSEMBLIES AND ROOFTOP STRUCTURES Master Permit No. ality Roofing Contractor, Inc. N.E. 4th Avenue Florida Building Code Edition 2010 High Velocity Hurricane Zone Uniform Penult Application Form. Section A (General Information) Process No. !ijIMCMEWM; JUN 0.5 262 BY: CI New Roof IX Reroofing ROOF CATEGORY ® Mechanically Fastened Tile O Metal Panel/Shingles O Prescriptive BUR -RAS 150 ROOF TYPE 0 Recovering ROOF SYSTEM INFORMATION Low Slope Roof Area (SF) 4 0 0 S q f t . Steep Sloped Roof 0 Repair O Mortar /Adhesive Set Tile D Wood Shingles/Shakes 0 Maintenance Miami Shores Village owl Section (Roof Plan) ZONING DEPT Sketch Roof Plan: Illustrate all levels and sections, roof drainssbn scuppers, o include dimensions of sections and levels, clearly Identify parapets. 15.34 TE scuppers awn ov r&auio ones SUBJECT TO COMPUANCE WITH ALL FEDERAL STATE AND CO( INTY RULES AND REGULATIONS �! i1IIIIIiii!ii!diIIII II 1 1111111111 2010 FLORIDA BUILDING CODE -- BUILDING ROOF ASSEMBUES AND ROOFTOP STRUCTURES Florida Building Code Edition 2010 High - Velocity Hurricane Zone Uniform Permit Application Form. Surfacing: N/ A Fastener Spacing for Anchor/Base Sheet Attachment: Field: 9 ° oc 4- Lap, # Rows 2 9 " oc Perimeter: 6 ° oc @ Lap, # Rows 4 @ 6 ° oc Corner:6 ° oc @ Lap, # Rows 4 6 ° oc Section C (Low Slope Application) Fill in specific roof assembly components and identify manufacturer (If a component is not used, identify as "NA") System Manufacturer: GAF Materials Corp. Product Approval No.: 0 7-1 21 9 . 0 9 Design Wind Pressures, From RAS 128 or Calculations: P1: –42.8 P2: –71 -7 P3: –1 OR. 0 Max. Design Pressure, from the specific Product Approval system: – 52 - 5 Deck: Type: wood Gauge/Thickness: 1 X 6 Slope: . 5 Anchor/Base Sheet & No. of PIy(s): Glas Base sheet Anchor/Base Sheet Fastener/Bonding Material: 1 1/4" R/S nails Number of Fasteners Per Insulation Board: Fully adhered • Field _NA Perimeter _NA Con er illustrate Components Noted and Details as Applicable: Woodblocking, Gutter, Edge Termination, Stripping, Flashing, Continuous Cleat, Cant Strip, Base Flashing, Counter- Flashing, Coping, Etc. Indicate: Mean Roof Height, Parapet Height, Height of Base Flashing, Component Material, Material Thickness, Fastener_Type, Fastener Spacing or Submit Manufactur- ers Details that Comply with RAS 111 and Chapter 16 V vs 4 v 1P d' FT. Ali kr Insulation Base Layer: High density wood fiberboard f Base Insulation Size and Thickness: 1 / 2" Base Insulation Fastener/Bonding Material: Type 1V mopping asphalt Top Insulation Layer: N /A Top Insulation Size and Thickness: N/A Top Insulation Fastener /Bonding Material: Parapet Height Base Sheet(s) & No. of PIy(s): N /A Base Sheet Fastener/Bonding Material: Ply Sheet(s) & No. of Ply(s): 3 plies of ply 1V Ply Sheet Fastener/Bonding Material: Type 1V mopping asphalt Top Ply: (1) Mlneral Cap sheet Top PI Fastener/Bonding Material: Type 1V mopping asphalt 2010 FLORIDA BUILDING CODE — BUILDING Mean Roof Height 15.35 SECTION R4402.13 HIGH VELOCITY HURRICANE ZONES — REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIONS R4402.13.1 Scope. As it pertains to the section, it is the responsibility of roofing contractor to provide the owner with the required roofing permit, and to explain to the owner the content of the section. The provisions of Section R4402 govem the minimum requirements and standards of the industry for roofing system installations. Additionally, the following items should be addressed as part of the agreement between the owner ant the contractor. The owner's initial in the designated space indicates that the item has been explained. 1. Aesthetics- Woricmmanship: the workmanship provisions of Section R4402 are for the purpose of providing that the roof system meets the wind resistance and water instruction performance standards. Aesthetics (appearance) are not a consideration with respect to workmanship provisions. Aesthetic issues such as color or architectural appearance, that are not part of a zoning code, should be addressed as part of the agreement between the owner and the contractor. 2. 1 ,� Renailing wood decks: When replacing roofing, the existing wood roof deck may have to be renailed in adcordance with the current provisions of Section R4403. (The roof deck is usually concealed prior to removing the existing roof system). 3. Common roofs: Common roofs are those which have no visible delineation between neighboring units (i.e., townhouses, condominiums, etc.) In buildings with common roofs, the roofing contractor and/or owner should notify the occupants of adjacent units of roofing to be performed. 4. Exposed Ceiling: Exposed, open beam ceilings are where the underside of the roof decking can be viewed from below. The owner may wish to maintain the architectural appearance; therefore, roofing nail penetration of the underside of the decking may not be acceptable. This provides the option of maintaining the appearance. 5, 1 " Ponding water: The current roof system and/or deck of the building may not drain well and may cause water to pond (accumulate) in low -lying areas of the roof. Pounding can be an indication of structural distress and may require the review of a professional structural engineer. Pounding may shorten the life expectancy and performance of the new roofing system. Pounding conditions may not be evident until the original roofing system is removed. Pounding conditions should be corrected. 6. %j , Overflow scuppers (wail outlets): It is required that rainwater flows off so that the roof is not overloaded from a buildup of water. Perimeter /edge wall or other roof extension may block this discharge if overflow scuppers (wall outlets) are not provided. It may be necessary to install overflow scuppers in accordance w ithithe requirements of Sections R4402, R4403 and R4413. 7, Ventilation: Most roof structures should have some ability to vent natural airflow through the interior of the structure assembly (the building itself). The existing amount of attic ventilation shall not be reduced. It may be beneficial to consider additional venting which can result in extending the service life of the roof. Date / i Contractor Signature Date Owmer /A• s Signature Da o Revised on 7/9/2009 LD BUILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION NOTICE OF ACCEPTANCE (NOA) GAF Material Corporation. 1361 Alps Road Wayne, NJ 07470 MIAMI-DADE COUNTY, FLORIDA METRO -DADE FLAGLER BUILDING 140 WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -2901 FAX (305) 375-2908 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by the BCCO and accepted by the Building Code and Product Review Committee to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Division (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BORA reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Division that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code and the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: GAF Conventional Built-Up Roof System for Wood Decks. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews and revises NOA No. 03 -0501:05 and consists of pages 1 thr000 gh 19. The submitted documentation was reviewed by Jorge L. Acebo. NOA No.: 07- 1219.09 Expiration Dade: 11/04/13 Approval Date: 03/20/08 Page 1 of 19 ROOFING SYSTEM APPROVAL Category: Sub - Categorv: Deck Type:, Maximum Darren Pressure Roofing BUR. Wood -75 psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Leak Buster MatrixTM 307 Premium Asphalt Primer GAF Mineral Shield"' Granules Leak Buster"' Matrix"' 305 Fibered Asphalt Emulsion Leak Buster"' Matrix"' 303 Premium Fibered Aluminum Roof Coating LeakBusterm MatrixTM 322 Elastomeric Roof LeakBusterTM Matrix"' Select Asphalt Emulsion Fibered 306 Leak Buster"' Matrix"' 204 Wet/Dry Roof Cement RUBEROMP Modified Bitumen Flashing Cement LeakBusterrM Matrix"' 201 Premium SBS Flashing Cement GAFGLASS #75 Test Dimensions 5necification 3, 5, 55 gallons 60 & 100 lb. bags 5 gallons 1, S gallons 55 gallons 55 gallons 1, 5 gallons 5 gallons 5 gallons ASTM D 41 ASTM D 1863 ASTM 1227 Product Description. Asphalt concrete primer used to promote adhesion of asphalt in built-up roofing. Granules for surfacing of exposed asphalt, cold process cement or emulsion. GAF Mineral Shield"' Granules shall be used for flashing applications only. Surface coating for smooth surfaced roofs. ASTM D 2824 Fibered aluminum coating. Elastomeric roof coating. Asphalt emulsion fibered. ASTM D -4586 Refined asphalt blended with a mineral ASTM D-3409 stabilizer and fibers. Permits adhesion to wet and dry surfaces. ASTM D 4586 Fiber reinforced, polymer modified Flashing cement ASTM D 4586 Asphalt flashing Cement 39.37" (1 meter) ASTM D 4601 Asphalt impregnated and coated glass mat wide base sheet. NOA No.: 07- 1219.09 Expiration Date: 11/04/13 Approval Date: 03/20/08 Page 2 of 19 Product GAFGLASe #80 ULTIMATM Base Sheet GAFGLASe Flex P1yTM 6 GAFGLASe Ply 4 GAFGLASe Mineral Surfaced Cap Sheet GAFGLASe EnergyCapTM Miineral Surfaced Cap Sheet GAFGLASe STRATAVENTe EiiminatorTM Perforated GAFGLAS® Flashing GAFGLASe STRATAVENT® EliminatorTM Nailable RUBEROIDe SBS Heat We1dTM Smooth RUBEROIDe SBS Heat We1dTM Granule RUBEROIDe SBS Heat- We1dTM 170 FR RUBEROID® SBS Heat We1dTM PLUS RUBEROIDe SBS Heat -We1dTM PLUS FR RUBEROIDe SBS Heat- We1dTM 25 RUBEROID® Modified Base Sheet Dimensions. 39.37" (1 meter) wide 39.37" (1 meter) wide 39.37" (1 meter) wide 39.37" (1 meter) wide 3937" (1 meter) wide 39.37" (1 meter) wide Various 39.37" (I meter) wide 1 meter (39.37 ") wide 1 meter (39.37") wide 1 meter (39.37") wide 1 meter (39.37") wide 1 meter (39.37") wide 1 meter (39.37") wide 39.37" (1 meter) wide Test Auec i ic*tion ASTM D4601 ASTM D 2178 ASTM D 2178 ASTM D 3909 ASTM D 3909 ASTM D 4897 D 3672 ASTM D 4897 D3672 • ASTM D-6164 ASTM D -6164 ASTM D-6164 ASTM D -6164 ASTM D -6164 ASTM D -6164 ASTM D4601, Type 11, UL Type G2 BUR Product • Description. Asphalt impregnated and coated, fiberglass base sheet Type VI asphalt impregnated glass felt with asphalt coating. Type IV asphalt impregnated glass felt with asphalt coating. Asphalt coated, glass fiber mat cap sheet surfaced with mineral granules. Asphalt coated, glass fiber mat cap sheet surfaced with mineral granules with factory applied layer of TOPCOAT° EnergyCoterm. Fiberglass base sheet impregnated and coated on both sides with asphalt. Surfaced on the bottom side with mineral granules embedded in asphaltic coating with factory perforations. Asphalt coated glass fiber mat flashing sheet available in three sizes. Fiberglass base sheet impregnated and coated on both sides with asphalt Surfaced on the bottom side with mineral granules embedded in asphaltic coating. Non -Woven Polyester mat coated with polymer - modified asphalt and smooth Surfaced. Non -Woven Polyester mat coated with polymer modified asphalt and surfaced with mineral granules. Non -Woven Polyester mat coated with fire retardant polymer modified asphalt and surfaced with mineral granules. Non -Woven Polyester mat coated with . polymer modified asphalt and surfaced with mineral granules. Non -Woven Polyester mat coated with fire retardant polymer modified asphalt and surfaced with mineral granules. Nonwoven Polyester mat coated with polymer - modified asphalt and smooth surfaced. Premium glass fiber reinforced SBS modified base sheet NOA No.: 07- 1219.09 Expiration Date: 11/04/13 Approval Date: 03/20/08 Page 3 of 19 Product RUBEROID® 20 RUBEROID® Mop Granule RUBEROID® Mop Plus (Granule) RUBEROID! MOP Smooth RUBEROID® MOP 170FR RUBEROID® MOP FR RUBEROID® TORCH Smooth RUBEROID® TORCH Granule RUBEROID® TORCH PLUS (Granule) RUBEROID® TORCH FR RUBEROIDD 170FR TORCH RUBEROID® 30 RUBEROID® 30 FR RUBEROID® ULTRACLAD® RUBEROID® Dual FR Vent Stacks (metal and plastic) Dimensions 39.37" (1 meter) wide 39.37" (1 meter) wide 39.37" (1 meter) wide 39.37" (1 meter) wide 3937" (1 meter) wide 39.37" (1 meter) wide 39.37" (1 meter) wide 3937" (1 meter) wide 39.37" (1 meter) wide 39.37" (1 meter) wide 3937" (1 meter) Wide 39.37" (1 meter) wide 39.37" (1 meter) wide 3937" (1 meter) wide 3937" (1 meter) Wide Test Specification Product Descrintion ASTM D 6163 .SBS modified asphalt base sheet. and ASTM D 5147 interply sheet reinforce with a glass fiber mat. ASTM D 6222 Non-woven polyester mat coated with ASTM D 5147 polymer modified asphalt and surfaced with mineral granules. ASTM D 6222 Non woven polyester mat coated with ASTM D 5147 polymer modified asphalt and surfaced with mineral granules. ASTM D 6164 Non -woven polyester mat coated with ASTM D 5147 polymer- modified asphalt and smooth surfaced. ASTM D 6164 Non-Woven polyester mat coated with fire ASTM D 5147 retardant polymer modified asphalt and °surfaced with mineral granules. Non -Woven polyester mat coated with fire retardant polymer modified asphalt and surfaced with mineral granules. Heavy duty, polyester reinforced, asphalt modified bitumen membrane, smooth surface. Asphalt impregnated, coated felt, surfaced with mineral granule. Heavy duty, polyester reinforced, asphalt modified bitumen membrane, granule surface. Heavy duty, polyester reinforced, coated with fine retardant asphalt modified bitumen membrane, granule surface. Heavy duty, polyester reinforced, coated with fire retardant asphalt modified bitumen membrane, granule surface. Non-woven fiberglass mat coated with polymer modified asphalt and surfaced with mineral granules. Nonwoven fiberglass mat coated with fire retardant polymer modified asphalt and surfaced with mineral granules. Woven fiberglass mat coated with Polymer modified asphalt and surfaced with aluminum, copper or stainless steel foil. Non -woven polyester and fiberglass mat coated with file retardant, polymer modified asphalt and surfaced with mineral granules. One way valve vent used to relieve built -up pressure within the roof system. GAF Vent Stacks are available in metal or plastic. NOA No.: 07- 1219.09 Expiration Date: 11/04/13 Approval Date: 03/20/08 Page 4 of 19 ASTM D 6164 ASTM D 5147 ASTM D 5147 ASTM D 5147 . ASTM D 6222 ASTM D 5147 ASTM D 6222 ASTM D 5147 ASTM D 6222 ASTM D 5147 ASTM D 6163 ASTM D 5147 ASTM D 6163 ASTM D 5147 ASTM D 6298 ASTM D 5147 ASTM D 6164 ASTM D 5147 TAS 100(A) ASTM D 1929 ASTM D 635 Product Leak Buster"' Matrix 302 Non Fibered Aluminum Roof Coating GAF Built -Up Roofing Asphalt RUBEROID® MOD Asphalt, Asphalt L & Asphalt P Leak Buster"' Matrixh 602 ' Leak BusterTM MatrixT°' 715 LeakBusterrm Matrix"' 531 WeatherCoteTM SeamCoteTM FireOut nd VersaShiele VersaShield® FB-1S VersaShield® FB-2S TOPCOAT® FireShield® MB Leak Busterm MatrixTM 201 SBS Flashing Cement Leak Buster"" Matrix"' 102 SBS Adhesive Leak Buster"' MatrixTM 202. SBS Flashing Cement Leak BusterTM Matrix""' 203 Plastic Roof Cement Leak Buster"" MatrixT , 103 Cold Process Adhesive Dimensions 5 gallons 100 lb. cartons, bulk 601b. kegs 5 gallons 5 gallons 2 gallons 2, 5 gallons 5, 55 gallons 350 sq ft. roll 350 sq ft. roll 350 sq ft. roll • 5, 55 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons Test Specification ASTM D2824, Type I ASTM D312, Types I, II, and IV 1 'll proprietary ASTM D -412 Product Descri on • Non-fibered aluminum pigmented, asphalt roof coating. Interply mopping and surfacing asphalt. ASTM D -21 -96 ASTM D1475 ASTM E -1644 ASTM D3019 ASTM D3019 ASTM D4586 AST' D4586 ASTM D3019 SEBS modified asphalt. Surface coating for smooth surfaced and mineral surfaced roofs. Surface coaling for smooth surfaced and mineral surfaced roofs. Surface coating for smooth surfaced and mineral surfaced roofs. Elastomeric roofing membrane. _ Low VOC, fire barrier coating. Non - Asphaltic Fiberglass -Based Underlayment. Non - Asphaltic Fiberglass -Based Underlayment. Non - Asphaltic Fiberglass -Based Underlayment. Elastomeric roofing membrane Cold Applied Modified SEBS Asphalt Adhesive - Flashing Grade. Cold Applied Modified SEBS Asphalt Adhesive. Cold Applied Modified SEBS Asphalt Adhesive — Flashing Grade. Standard Plastic Asphalt Roofing Cement Cold Applied Asphalt Adhesive. NOA No.: 07- 1219.09 Expiration Date: 11/04/13 Approval Date: 03/20/08 Page 5 of 19 Product Dimensions Leak BusterTM MatrixTM 5 gallons 303 Fibered Aluminum Roof Coating Leak BusterTM MatrixTM 5 gallons 304 Non Fibered Aluminum Roof Coating APPROVED INSULATIONS: Product Name. EnergyGuardTM RA, RN Composite A & N EnergyGuardm Fiberboard EnergyGuardTM Permalite EnergyGuardTM GAFCANTT11 EnergyGuardTM Permalite Recover Board EnergyGuardTM Tapered Edge Strip EnergyGuardTM Perlite - EnergyGuardTM High Density Fiberboard EnergyGuardm Composite EnergyGuardTM Composite RA Wood Fiber High Density Wood Fiberboard Perlite Insulation Dens Deck, Dens Deck® Prime, Dens Deck Dura Guardm Structodek SecurockTM Test Product Snecification Descution ASTM D 2824 . Fibered aluminum coating. ASTM D2824, Non-fibered aluminum pigmented, asphalt Type I roof coating. Table 2 Product Description. Polyisocyanurate foam insulation Polyisocyanurate foam insulation with high density fiberboard or Permalite partite insulation. Fiberboard insulation. Perlite insulation board. Cut perlite board Perlite recover board Tapered perlite board Perlite insulation board High density wood fiberboard insulation. Polyisocyanurate/wood fiberboard composite Polyisocyanurate/wood fiberboard composite Wood fiber insulation board Wood fiber insulation board Perlite insulation board Water resistant gypsum board Wood fiber insulation board Fiber reinforced roof board Manufacturer (With Current NOA) BMCA ' GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. BMCA BMCA generic generic generic G-P Gypsum Corp Knight Celotex USG Corporation NOA No.: 07- 1219.09 Expiration Date: 11/04/13 Approval Date: 03f20/08 Page 6 of 19 APPROVED FASTENERS: Fastener Number Product Name 1. Drill -T&'°s #12 Standard, #14 and #15 extra Heavy Duty Fastener , Heavy Duty Roofing•Fastener Drill-Teo ASAP 2. 3. 4. 5. Drill TecTm #12 or #14 Standard screws with AccuTrac Plate Drill-TecTm Galvalume Plates Drill -TecTm Polypropylene Plates 6. Dri11- TecTD° AccuTrac Plate EVIDENCE SUBMITTED: Test Aeenev, Factory Mutual Research Corp. PRI Asphalt Technologies, Inc. IRTofS.Fl. TABLE 3 Product Description Insulation fastener and Base Play fastener for steel, wood & concrete decks. Pre - assembled Drill - TecTm Fasteners and metal and plastic plates. Base sheet fastening assembly. Round Galvalume stress plates. Round polypropylene stress plates. Square Galvalume coated steel plate. Test Identifier J.I.2B8A4.AM J.I.3B9Q1:AM J.I.ODOA8.AM. 1.I.ODIA8.AM J.I.0Y9Q5.AM 3029832 GAF -012 -02 -02 GAP- 020 -02 -01 02-005 02 -014 Dimensions Various Manufacturer (With Current NOA) GAF Materials Corp. Various GAF Materials Corp. Various GAF Materials Corp. 3" and 3W GAF Materials Corp. 3 °° and 3 A" GAF Materials Corp. 3" Square GAF Materials Corp. Description 4470 4470 4470 4470 - TAS 114 4470 -TAS 114 4470 - TAS•114 Physical Properties ASTM D 4977 TAS 114 TAS 114 Date 07.02.97 01.08.98 07.09.99 07.29:94 04.01.98 05.11.07 11.06.01 02.01.02 01.18.02 03.22.02 NOA No.: 07- 1219.09 Expiration Dec 11!04113 Approval Date: 03120/08 Page7of 19 PROVED Deck Type 111: Deck Descriptions System Type A: LEES Wood, insulated • 19 /n" or greater plywo or wood plank Anchor sheet mechanically fastened, all layers of insulation adhered with approved asphalt. All General and ,ystem Limitations sh apply. One or more layer of any of the following ansulatlons. insulation Layer (T . ' le 2) (When applicab : Steel plate only = , plas _ ) EnergyGuardns EnergyGua t nergyGUardni RA Composite Minimum 1" thi EnergyG Minimum 1/2" thi EnergyG Minimum 3/4" thi Fiberglas (Minn. Note: All ins within the E Standard RAS as base layers • substrate. Co polyisocyan Eliminator on all isocyana Fire Barrier: (optional) Anchor sheet High Density W k erlite 15/16 thick) 94 Insulation Fasteners ]peFastener t c plate only (Table 3) Co k96 ,,, ^,,'te, EverGuard ®150; EnergyGnardTm RA, N/A' N/A Fiber, Ene g _,;; G Recover Board, Wood Fiber, • N/A N/A It it on shall be a «„ ', the anchor skeet in range and at a rate of 20-40 lbs/100 fie. Please refer to Roofing Application 17 for insuia iron attacs' { ent insulation listed as base layer only shall be used only th a secwa' Dyer of approved top layer insulation installed as the final membrane polite insulatdo els may be used as a top layer placed with the side facing down. GAF rid'" fires either a ply of GAFGLAS® STRATAVENT® erforated laird dry or a layer" of EnergyGuartirm Perlite or wood fiber overlay board to app FireOutTm Fire ;: wrier Coating, Ven hield®Non- Asphaltic Fiberglass -Based Underlayment or Securockw. GAFGLAS® #80 ULTIMATM Base Sheet, STRATAVENT! Eliminator° " • Nailable, RUBERO ® Modified Base Sheet, RUBEROID® 20, RUBEROID Heat WeWM Smooth or RUBERO ® Heat- Weld"'°3 25 base sheet mechanically fastened as described below; GAFGLAS® Ply 4, GAFGLAS® Flex Plind 6, GAFGLAS® #775nular ring shank any of above Anchor sheets attached to deck with approved and shank two nails d tin caps at a fastener spacing of 9" o.c. at the lap staggered rows 12" o.c. in the field. (Maximum Design Pressure -415 ps , See General Limitation #7) • N/A N/A N/A • N/A mopping of approved hot asphalt Fastening Optons: IIlIr j APPIZOVEDxi 11 NOA No.: 07- 1219.09 Expiration Date: 11/04/13 Approval Date: 03/0108 Page 8of 19 ® #75 Base Sheet or . Gg,AS�' Ply 4 GAFGl�� Flex of deck with Drill-Teem #12 standard, #14 »Drill attached ,l eck. or Deli -TecTM Accu'I'rac Plates, 7'astenang �DPdo GAF any Ofabove �ychor sheets are e9�iy 3 2" lap. The other rows or # 15 . in and One row is in the 2 side la . 12" ,. 3 rows. 12" the field o�'�� Limitation #7) . See a,,,,� ,..xi�nate�` i2 o.c. in tic Design '45psf9 S of above Anchor 6, GAFGLAS #75 Base Sheet or any S ®Flex Ply ring 'shank �� and tm caps � a ' �r p,FGLA with approved ann and in two rows 9" o.c. in the attached to deck ' sheets fastener of 9" o.c. at the 4" lap Fagg General y�tation #� field. 52'.5 9►� Smooth, animas ��� � �, Bgffa �,'; �aaae -- � RUBEROID ®� base ® #8OULTIMATm, RUBEROII�®20, shank nails and inverted GAFGLAS approved PA" annular ring sheet attached to deck with of 9" o.c. at the 4" lap and in two rows . at a fastened' spacing of the membrane. 3" steel staggered wlwe. a finer spacing of 9" o.c. in the center e Design Pressure —60 psf See General GAFGLAS® #75 ase Sheet or any of above Anchor sheets attached to deck with Drill -Tec' #12 dard, #14 or # 15 Screws and 3" Dri11 -Teem steel plate or Drill-Teem AccuTrac Plates, 12" o.c. in 4 rows. One row is in the 2" side lap. The other rows are equally spaced ' . proximately o.c. Lon #7j d of the sheet. (Maximum ��t � =::n Presswe —60 psf, See shazaknails Any of above Anchor sheets attached to deck approved annular ring and 3" inverted Drill-Tec i • nsulation plates at a fastener spacing of 9" o.c. at the 4" lap staggered in two rows 9" in the field. gifaXbilliffd sole — 6 0 psf, See General Lnitaton #7) GAFGLAS® #75 Base Sheet or any of •ve Anchor sheets attached to deck with Drill-Teem #12 standard, #14 or # 15 Screws and 3" Drill-TecTm sal plate or DtiYy_TecTea AccsuTrac Plates, 8" o.c. �� rows. x�ly One 9" o.c. in the field of the sheet. is in the The other rows are equally spaced ap (Mar.Ianasna Desigia t' °ressawe —75 psf, See General Limitation #7) ase Sheet: (Optional) Install one ply of GAFGLAS® #75, GAFGLAS® #80 ULLTIMAT"l Base Sheet, ®AI�GLAS® STRATA �EROID Mop Smooth, RUBEROID® RUBEROID Modified Base Sheet, 20 RUBEROID® Heat We1dTa Smooth or RUBEROID Heat-Weldrfd asphalt y over the top layer of insulation. A r. ere with any appro ved mopping applied within the EVT range and at a rate of 20-40 lbs.aq; (see General Limitation #4). Ply Sheet: -One or more plies G ®FGLAS® PLY 4, GAFGLAS® Flex P1yTm 6 sheet, #80 Ultima, RUBEROLD Mop Smooth or RUBEROID® 20 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs.sq. ABP.ROVEDI.: NOA No.: 07-1219.09 Expiration Date: 11/04/13 . Approval Date: 03/20/08 Page 9 of 19 Cap Sheet: Surfacing: Maximum Pressure: (Optional) One ply of GAFGLAS® Mineral Surfaced Cap Sheet or GAFGLAS®EnergyCapT' Mineral Surfaced Cap Sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20- 40lbs. /sq. (Optional, required if RUBEROID® MOP Smooth or RUBEROID® 20 is top membrane) Install one of the following 1. Gravel or slag applied at 400 lbs.sq. and 300 lbsJsq. respectively in a flood coat of approved asphalt at 60 lbsJsq. or applied in a flood coat of Leak Buster Matrix'' 103 Cold Process Adhesive applied at a rate of 3 gal./sq. 2. GAFGLAS® Mineral Surfaced Cap Sheet, GAFGLAS® Energy Cap Mineral Surfaced Capsheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20- 40lbs.sq. 3. Leak Busteirm MatrixTm 303 Premium Fibered Aluminum Roof Coating, at 1.5 galisq. 4. Leak Austell Matrix 715 , Leak Buster Matrixim 322, TOPCOAT MB +, TOPCOAT® Fireshield Elastome is Roofing Membrane, applied at 1 to 1.5 gal./sq. 5. Leak BusterTM Matrix' m 602 MB Xtra Elastomeric Roofing Membrane, EnergyCote® roof coating applied at 1 to 1.5 galfsq. 6. '3 OPCOAT® Surface Seal, TOPCOAT® Fireshield® SB Solvent based Elastomerie Roofing Membrane applied at Ito 1.5 galfsq 7. Advance Green Technologies Photovoltaic Laminate solar energy collector auxiliary roof equipment installed in compliance with manufacturer's specifications and applicable Building Codes. See Fastening above. NOA No.: 07- 1219.09 Expiration Date: 11/04/13 Approval Date: 03/20/08 Page 10 of 19 WOOD DECK SYSTEM L ,id ATHONS: 1 A slip sheet is required with Ply 4 ,, d Flex Flynt 6 when used as a mechanically fastened base or anchor sheet. 2. Minimum 1/4" Dens Deck ' or l" Type X gypsum board is acceptable to be installed directly over the wood deck. GENERAL um:awn NSt 1. Fire classification is not part of acceptance, refer to a current Approved Roofing Materials Directory for fire ratings • li this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EDIT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer approved asphalt, 3. All standard panel sizes are accep' . le for mechanical attachment. When applied in appro panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12'° diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each sidelap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in on. Asphalt application of either system shall be at a minimum rate of each ribbon to allow cross ventil 12 lbs.sq. Note: Spot as fi = systems s ' n be liffiited to a maximum design pressure of -45 ps£ 5. Fastener spacing for insulation attar eat is based on a Minimum Characteristic Force (F') value of 275 lbf., as tested ii compliance with Testing A r ,• lication S TAS 105. If the fastener value, as field - tested, are below 275 lbf. insul . 'on attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment a specific a minimum fastener resistance value in conjunction with the maxim by the Building Official, system. Shoul4 the fastener resistance be less than that required, or a revised fastener spacing, prepared, signed and sealed by a Florida Registered Engineer, Registered Roof Consultant may be sub !, . Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Stan,. =, , .. RAS 117. uirenients of these areas. 7. Perimeter and corner areas shall co ..ply with the enhanced uplift pressure recl hence w Fastener densities shall be increased for both insulation and base sheet as calculated Flco compliance with i registered Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred wi _; N + A, General Limitation #9 will not be applicable.) 8. All attachme4t and sizing of perimeter hailers, metal profile, and/or flashing termination designs shall conform with Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure lirnatetion listed moor be poia bon shall be permitted zones enhanced field, perimeters, :� d corners). Neither rational analysis, fastening at enhanced pressure zon, (i.e. perimeter extended corners and corners). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10.. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 9B-72 of the Florida Administrative Code. E OFT ' S ACCEPTANCE NOA No.: 07- 1219.09 Expiration Date: 11/04/13 Approval Data 03/20/08 Page 19 of 19 03/23/2009 l4 ;zz 306761.e3679 li's�� 7 �{pp ABC MIAMI it ING .i ,'. TEMA 1. = k i lil SYS1lEM S lei' C G O 1 ROOF COVERING MATERIALS (TEVT) Roofing Syste s►e G ) Canthistad "GA9'1`FMP'Fermalite Recover Board" may be used in lieu of any perlite insulation in any of the following NC s ,asificatior's• with Hot Unless otherwise indicated, an of the "Awlsalt Felt at Z. s itl H Roofing Asphalt" ms. y be urfaced with "Fireahieldl MS Class Ay B and C Hot roofing asphalt, for use with organic art. glass felts or modified bitumen membranes. membrane may be used in lieu of "Ruberaid teat Weld" SBS roofing "Ruberoid Mop" SBS products in any applicable Classification. s2 300P COVERING MATERIALS (VENT') Roc f'ing Systems (TGFIJ)_Cnntinued Base Coat: "A•38 Series", 0.75 gal /se. Second Base Coat "A•38 Series'. 0.7+ gal/se. Wear Coat " A-38 Series ", 0.75 gal /se plus walnut shells at O,i5 Ibis per Surfacinv " A -38 Series ". 0.79 gal /se plus walnut shells at 0.75 1bt per 46 1t le NC Incline 3/4 Foam; Spray application of 2•in. thick "1'olyfoam 273" (2.7lb /ft-3 Srcing Spray application of 2S to134- "U4736" (alumithvm) 47 Decks NC Insista4ikan Spray application of 2-itt. thick "Pnlyfoam 273" (2.7 1b /f13 )Suzfaciaip Spray application of 28 to 34.rsu'ls "U-V82°. (ivory) GAF MATERIALS CORP R13 836't ALPS RD, WAYNE NI 07470 may be utilized as an "Ruberaid 20" CT "Ruberoid Modified Base Sheet" Claseifitilzed. alternate to Type G2 base sheets in any of the following 1/2 in. thick (min) gypsum board or •1/4 in. thick (min) G-P G psta % 10ensDeckS may be used in any existing noncombustible deck Cam When this is done, the resetting vytea« is acceptable combustible (15/32 in. min) reel' decks. The joints in the gypsum board and • overlayment board ffceet 6 in. . with ed below 1aymIf polystyrene s part of the roof system, g�1'1 4" or "Ply 6 may be adhered to G-P Also, multiple plies of "GA y Gvosrma' DertsDeekk in 'hot asphalt. .` " in any ereyGuard Ultra" is an acceptable alternate to "Energy Guard" S� la AF t g�tor Venting Base Sheet (Mailable)" may be mechani- cally attached or hot mopped over noncombustible decks and as a recover over exMir:Asoi g insulation may be utilized as waiver board o-vee " - GUARD" insulation it any of the following syste s. Unless otherwise indicated, the roof insulation is mechanically fastened, adhered with hot asphalt or urethane insulation adhesive. Po1 stY- rene refete nee in any the following C1a. +facatons include "ENERGuan References to glass fiber insulation include "PutargyGuard Fiberglass Insu- lation". ASPHALT FELT SYSTEMS WITh HOT ROOFING ASPHALT G2 asphalt glass mat base sheet ( "GAFGLAS 475 Base fit" or *10 ULTIMA" ) is a suitable alternate for Type G1 asphalt glass fiber pl sheet ( "GAFGLAS Ply 4" or "GAFGLAS Ply 6" ),in the Caw A,B or C r systems indicated below. The roof deck may first be covered with a Type G2 asphalt glass mat base sheet GAF Stratavent Eliminator Venting Base Sheet )(Perfo m "GAF Stratavent Eliminator Venting Base Sheet (Mail abler and nailable to be mechanically attached granule side down. As an melon T G2 asphalt glass rout base sheet ( "GAFGLAS 4175 Base " #J60 ULTIM A" or "GAP Stratavent l:tstninator Venting Base Sheet (Mailable)" may be subsetuted for G] asphalt glass fiber ply sheet ( "GAFGLAS Ply 4" or "GAFGLAS Ply 6" ) as the nailed base ply in the following systems. be solid mopped, m or meehani" Bottom ply or base sheet may opped spot -opt tally fastened. Ltnless otherwise indicated. all insulations may be hot mopped or - sallyy fastened. "GAFGI.AS Planting" or "Rubetaid" may be used for EIsshing in any of the Class A, 8 or C systems listed below. When "perlite" is referenced, this includes "C.:APTPM1' PERMALTTEG" or nv other UL Classified perlite insulation. ed stone or slag arc suitable alternate's for gravel in any of the Claw A, B or C system listed. Structural Went fiber building unite are considered suitable to be included as a desk of the following under any an or of the fillk'wa-i Class A. B C-15/32 Or NC. systeres The use f'F''m' does not adversely effect the rating. The are of 1/2 in min gypsum board is an acceptable alternate for insulation over C -15/32 decks. ?114 sir perlite board The use of polystyrene insulation board between ms.n fie! t is a and deck with rosin r in paper (perde n-sin pa per• f n suitable alternate for isoeyanurate board in the following Clara A. 8 or C systems. N .URTCI R Pe" and •'B V1CA "BMCA Erierg•Guard RA , "BMCA Tapered EnergyC ansand insula- tion pier yCuard 1W' may be substituted for amt Atlas polytsctty lion io any of the following Clasalficationa. Trumbull "Piuma Mt+e" maybe utilized with any of the following "Asphalt Felt systems with Hut Roofing A hats ". CA t.AS MO Premium Base Rieet may be used in any of the following PAGE 04 Class A Deck: C -15/32 Inane 3 Imitation (Optionalk One or more layers perlite, wood fiber, glass fiber, isc yftnutate, urethane, perlite /Isocyanurate compositer partite/ urethane Costspkmite, woad fiber /isoeyanurate composite, phenolic, any thickness. Ply Steele Three or more la Surfaadnn Gravel. thtelirte; 2 'heck: Insulation (Optional): 2 a e rs partite, wood fiber, glass 1naulataan rate, r One or' more layers prate corshpr Bite, perlite/ fiber, iseuyanurash. urethane, polite /it te c gosfte, phenolic, any urethane mmpthsiie, wood fiber /isotyan • Ply Three or. nsore layers Type Gl • "GAFGLAS Ply 4" or "CAPCLAS Ply 6 ". Cap Sheet One layer 'Type G.3 "GAFGLAS Mineral Surfaced Cap Sheet" or "EnergyCap Mineral Surfaced Cap Sheet". - Pecks NC ona r One or more layers Mite, wood fiber, an fiber, isacyanurate, urethane, peclite /isocyanurate composite, pes]ite/ urethane composite, ward fiber /isocyamrrate composite' phenolic, 2 in. PI max. Stieet Two or more layers Type GI "GAFGLAS Ply 4" or "GAF - One layer Shut yer 7ppe Ply 6 "' Cap G3 "GAFGLAS Mineral Surfaced Cap Sheet" or "Erter&yCap Mineral Surfaced Cap Sheet". . Deck: NC It", 4 in. max, hot mopped FastaLatiems One or two layers "Isotherm Ply Sheet Any UL Classidtd gravel surfaced Class A asphalt glass fiber mat system. Iodine 1 5. O Mp eat3� Red rosin rap� nailed to deck. Slip $free (Opne layer G2 '`GAFGLAS *75 Base Sheet" (rnay be Bass Sliest One lay � naitedl. T Cl "GAFGLAS Ply 4" GAFGLAS Fly Shed One or more layers Type Ply 6 ". Cap Sheer Ona layer 1 G3 "GAFGLAS + Sheet". Mineral Surfaced Cap ' Sheet" or "EnergyCap Inclines 3 Deck: NC GI "GAFGLAS *75 ease Sheet' . Sale Sheet One late Type Ply fifteen One or more Byers Type GI "GAFGLAS Pig 4" or'GAP- csp Ply e 6 G3 GAFGLAS Mineral Surfaced Cap Cap Skeet One lager Type Sheet" or "EnergyCap Mineral Surfaced Cap Sheet". 7, Deck: C -15/32 Incline; 2 Insulations One or more layers polite, glass fiber, iacicyanurate, utd thane. perlite /isc+cyanurc'te composite, perlite /urethane composite, phe- nolic, l.0 in. min (offset from plywood jostle 6 in.). Base Sheet One or ram layer Type G1, G2 or G3. Mernbranec One or more layers "Aubemid Torch" (Smooth or Granule). 'Rebenrid Torch Plus" (granule). " Ruberoid Map" (Smnoth or Granule) or "Robert-lid Mop Plus" (rnrartulc). Cap Sheet Type G3 C,APCLAS Mineral Surfaced Cap Sheen or " EnergyCap Mineral Surfaced Cap Sheet", hot mopped. • 8 Deck C.15/32 incliner 2 TnsolattIo (Optionatl: One or more layers periita, wood fiber, glass fiber, tsoc ranurate, urethane, perlite /isorye'vrete coopasdte, prlite/ ti urethane composite, wood ther /iva e ryarurate compost ph any thickness. Base Streets Two or more layers: Type C2 or G3, Ply Sheet tOOptionalrn One or more layers Type C. Membranes gins or more lawns "Rubcroid Torch" (Smooth or (;rsmuleb "linberoid Torch Plus" snit ule). 'Rtiberoid Mop" (Smooth or Granule) or'•Ruberoid Mop ALAS Plea Ply 6" is n suitable alternate to "C•APCLAS Ply 6 ". LOOK FOR THE UL K ON PRODUCT