Loading...
RF-11-495Inspection Worksheet Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL Phone: (305)795 -2204 Fax: (305)756 -8972 10 Inspection Number: INSP - 157430 Permit Number: RF- 3- 11-495 Scheduled Inspection Date: June 21, 2011 Inspector: Bruhn, Norman Owner: DURU, CLEMENT Job Address: 139 NW 102 Street Miami Shores, FL 33150- Project: <NONE> Contractor: QUALITY ROOFING CONTRACTORS INC Permit Type: Roof Inspection Type: Final Roof Work Classification: Tile Phone Number Parcel Number 1131010220080 Phone: (305)953 -3333 Building Department Comments NEW CONSTRUCTION WITH TILE Inspector Comments Passed ill O Failed Correction Needed Re- Inspection Fee No Additional Inspections can be scheduled until re- inspection fee is paid. June 20, 2011 For Inspections please call: (305)762 -4949 Page 5 of 25 RE: Permit# RF -3 -1 1 -495 Miami Shores Village Building Department INSPECTION AFFIDAVIT 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 DATE: March 31 , 201 1 Carlos Arocho licensed as a (n) Contractor/ Engineer /Architect, (Print name and drde License Type) License #: 000017889 On or about April 4, 201 1 FS 468 Building Inspector , I did personally inspect the roof deck nailing and (Date & time) Secondary water barrier work *at 139 N.W. 102 Street Miami Shores, F1 33150 (Complete Job Site Address) Based upon that examination I have determined the installation was done according to the Hurricane Mitigation Retrofit Manual (Based on 553.844 F.S) Signature State of Florida County of Dade: The undersigned, being the first duly swom, deposes and says that he/she is the contractor for the above property mentioned. Sworn to and subscribed before me this 3 / NOTARY PUBLIC•STATE OF FLORIDA Notary Public, Sate of Florida at Large '",,s Marylou Commission # D93 045 .,,.�' Expires: OCT.102013 BONDED THRII ATLANTIC BONDING CO,1NC. • *General, Building, Residential, or Roofing Contractors or any individual certified under 468 F.S. to make such an inspection. Include photographs of each plane of the roof with permit # and address # dearly shown marked on the deck for each inspection Revised on 5/21/2009 F. FLORIDA INTERNATIONAL ENGINEERING AND TESTING LAB LLC 16701 SW 117 Avenue, Miami, Florida 33177 .E. Telephone: (305) 378-1991- Fax: (305) 378-1997 FLORIDA INTERNATIONAL ENGINEERING & TESTING LAB NIGHT •INNOV4TION• INTEGRA PION Miami-Dade Lab Certif ication # 07- 0612.11 SITE SPECIFIC INFORMATION Job Address: Contractor: Type of Tile: Owner Name: App. Sq.Ft: /19 At k) /P2 I 1/4D1I 4�Pg � pp Install Date: Q!4 I n' ! `9Dg7/ fiG Permit # .3 • %1.4f 6 Air /71-- Cirl 11C-D �P"l� -Tll�l ra Approx. Height Test Date: Floor: Slope: Testing Equipment: Shimpo Representatives of Florida International Engineering and Testing Lab., Inc performed the static load test on the roofing tile at the above referenced project. The purpose of this testing was to verify whether the installed tile roofing system is capable of resisting the applied test load of 45 pounds uplift force. This testing was performed in general accordance with Miami Dade Building Code Protocol TAS 106. The static load was applied utilizing a calibrated scale and force measuring instrument (dynamometer). A hook which is connected to the loading instrument was placed under the exposed edge of the tile. Test load of 40 pounds force (lbf) was applied and also held for more than 5 second at each test location. In addition to the static load test, the tested tile was also visually inspected for any kind of adhesion failure after completion of each test. 1 2 3 4 5 6 7 8 9 10 11 12 exult' T 21 22 Result . _ 41 42 pio 61 62 Result 5 81 101 121 82 102 122 23 43 63 83 103 123 44 64 84 104 124 25 45 65 85 105 125 26 y 46 66 86 106 126 27 28 47 67 87 107 127 48 . 68 88 108 128 29 49 69 89 109 129 30 50 70 90 110 130 31 51 71 91 111 131 32 52 72 92 112 132 13 33 53 73. 93 113 133 14 34 54 74 94 114 134 15 35 55 75 95 115 135 16 36 56 76 96 116 136 17 37 57 77 97 117 137 18 38 58. 78 98 118 138 19 39 59 79 99 20 40 60 80 100 119 120 139 140 Based on our findings, we conclude that the installed roofing tile at the above referenced project is capable to resist the applied test load. Therefore we conclude that it meets the Miami Dade Building Code Compliance Protocol TAS 106. Attached is the roof plan showing approximate test locations. Respectfully Submitted: \\ / 64241 V nayagar M. Balakrishnan V, P .E. State of Florida Eic # 63107 FLORIDA INTERNATIONAL ENGINEERING & TESTING LAB, LLC Miami- Dade Lab Certification # 07-0612.11 Job Address: / 3 / /1 W /0 "66' r.) A,'! Contractor. QM- liT Z;DF;A) 4 Other. Sketch of Roof •■■■■■■ !�1■■■■■■■■i ■ ■1uiaiwpiui■■■ ■■■■ ■ ■ ■■ ■�■■UI1 ■■■■■ ■■■■ ■--- - -..�. ■■■■■■■ ■ ■ ■ ■ ■ ■■ ail■■■■■■■■ ■ ■ ■��:��■■■ /'� ■■/�7.��i�■ ■ ■■ ■ ■■ ■ ■ ■ ■■■■M■■■■ ■■i ■■■!712.1 i4Mi':S1111ii■■ ■■■ ■ ■ ■■ ■■ ■i � ' ■ ■■ ■sM ■MMM� ■■ ■; r■■C J!Z2 41'f ■■■■' ■ ■■ ■■■■■■ii11 ■1 i./? ■ ■M■R'►� !■ ■WEM ii■■ ■11i■■■■■■ ■■ ■ ■■■■11■170 ■i11MILI ■■►i/I1Mi ■'i 4islilii■■■■■ ■■ ■■■■■1(1 ■Ei ► ■ ■ ■II■!MMiMENW.` 5 iii ■1111 ■■■■ ■■ ■ ■ ■ ■ ■■ ■uaa■1 ■ ■►` '! ■ ■ ■1K ■v ■■ ■RIi i■■ ■■iIIIIII ■ ■■ ■u■■ ■■■ii�lii ;i`�`?)i��.��/ ■ ■ ■IlpI■ ► ■,u 1Ii ■■■i■■■ ■ ■■■ ■■ 'ui 5114 1111Pr .may :, ,,,� ■i��®,■ ■,■■ ■ ■■■ ■ ■1E�Iiui ■R1Aa ■1G;' ii%■iliwe` F'i ■Iii ■ ■ ■ ■■■ ■■ ■ ■ ■■■IiI■II ■M.� <. ■II■■au ■■■ \i[4■IIII■I■ ■■ ■■ ■ ■ ■ ■ ■■■1i■i T :sli ■■■ ■■11'. 21111 ■■ ■■■I I 'J lI■ ■■■■ ■■ ■ ■ ■■ ■ ■ ■1II�I'I Plig11 11111■'LVIRE ■■ ISMI III. ■■ ■>■■ ■■■■■ ■■11 ■R %■'`! ■■[ ■ ■ ■iMi�i %iili>iii'''! ■ ■■ ■ ■ ■■ ■ ■■ ■ ■■■iI ■■ �i�ri ■i ■11� ■ ■�!s'1!1�1 ■ ■■■■ ■■ ■■■ ■M■ ■1i■1 ■a ■ ■S1tii ■1r! f iVdaIa ■■1111■■■ ■■■■■ ■■1.i■ff Y1■ ■iiiiiiugi/1 ■ ■i■i ■■Iti■■ ■■1111 11111111111111111111111111111MHIPLINPIUMEMEMPITVIVAMERRIUM ■■1111■■ ■11■■ NINIGAIIIIiiiillaINNUIRMICia1111111111111111111111 1111111•1111111111111.111711111EIMINPREIEWRIZMOIMIIIIIIIIIIIII ■■■ ■■ ■G!iii ■ M ■:,`� % ■tui� ■1 i viii ■iI''1 ■ ■■■■ ■■ 11111111111111101111111111111M1iiittamilliiitkriallirelEMISEIREMMI ■1111■ ■■ ■11■1 i■ic din. ■ln/ ■■ ■bi■ wania■if ■i■■■■■ ■■■■■■■1ii1 ■ , ■ %■iii #iiiMiii ■ ■ ■ ■ ■it■ ®1111■■■ ■■■■■■ ■1i1■1111lii:l111FiN i ■'? IMi ■IMillR■ ■■i■■ 011111111111111111111111 mcomanabranumumanakeinaummaaam ■ ■■■ ■ ■1111lMKANIMM■■MAIM f■ ■i! ■■iPMIBM11111111■ ■ ■■ ■ ■■ ■1121r1LINIMM I■ O ■EIN M1ININI ; 1111■ ■1111■ ■■i■■iilii® ....TURN ■ /■ ■111■iiii ■ ■i■ ■ ■ii■■ ■ ■ ■ ■ ■i ■,i1R iii :. A1i1i1i:i5 ■ ■■ ■1111 ■■ ■ ■■! ■■ ■■■ ■■ ■1111. ■ ■■■■iiiaiiii ■■ii■ ■i ■■■ ■■■■■■ i■ i.■ I■ ■■■■11'liiii■■Mi ■ ■■ ■ ■ ■■■ ■■■■ ■ ■■ 1111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 ■■■ ■ ■■■111111mii1i1liii ■ii■ ■..Mini. ■ ■ ■ ■i ■■■ ■■■■■■ ■■1■1l ■ ■■■■■■■■Ur1i■■ ■ ■■■11■ ■■■ ■1111 Notes (1 "14r SIC ®R®,, CERTIFICATE OF LIABILITY INSURANCE DATE PRODUCER Lakes Insurance Group 6001 NW 153 Street Suite 205 Miami Lakes, FL 33014 (305)512 -4336 3 THIS CERTIFICATE IS ISSUED AS A TTER OF INFORMATION ONLY AND CONFERS NO RIGHTS UPON THE CERTIFICATE HOLDER. THIS CERTIFICATE DOES NOT AMEND. EXTEND OR ALTER THE COVERAGE AFFORDED BY THE POLICIES BELOW. INSURERS AFFO COVERAGE NAIC B 3PSURED Quality Roofing Contractor Inc. 13800 NW 1 Avenue Miami, FL 33168- INSURER A - Hermitage IfISUMECIe Co. INSURER 3: INSURER C: INSURER D: INSURER E: COVERAGES INSURER F: THE POLICIES OF INSURANCE LISTED HAVE BEEN ISSUED TO THE INSURED NAMED ABOVE FOR THE POLICY PERIOD INDICATED. NOTWITHSTANDING ANY REQUIREMENT, TERM OR CONDITION OF ANY CONTRACT OR OTHER DOCUMENT WITH RESPECT TO WHICH THIS CERTIFICATE MAY BE ISSUED OR MAY PERTAIN. THE INSURANCE AFFORDED BY THE POLICES DESCRIBED HEREIN IS SUBJECT TO ALL THE TERMS, EXCLUSIONS AND CONDITIONS OF SUCH POLICIES. AGGREGATE LIMITS SHOWN MAY HAVE BEEN REDUCED BY PAID CLAIMS. EMIR ITN ADD% DVSRD TYPE OF INSURANCE GENERAL ® COMMERCIAL GENERAL LIABILITY ❑ ❑ CLAIMS MADE ® OCCUR POLICY NUMBER PODGY DATE MUM/ EXPIRATION DATE piwroorm utaiTs ❑ FZ $500 BI/PD Ded. GEN'L AGGREGATE UNIT APPLIES PER ❑ POLICY ❑ PROJECT ❑ LOC a2248 03/24/11 03/24/12 EACH OCCURRENCE DAMAGE TO RENTED PREMISES (Ea occurence) MED EXP (Any one person) PERSONAL & ADV INJURY GENERAL AGGREGATE PRODUCTS - COMP/OP AGG 500,000 50,000 Excluded 500,E 1,000,000 500,000 AUTOMOBILE LIABILITY ❑ ANY AUTO ❑ ALL OWNED AUTOS ❑ SCHEDULED AUTOS ❑ HIRED AUTOS ❑ NON OWNED AUTOS GARAGE LIABILITY ❑ ANY AUTO COMBINED SINGLE LIMIT (Ea accident) BODILY INJURY (Per person) BODILY INJURY (Per accident)) PROPERTY DAMAGE (Per accident) AUTO ONLY - EA ACCIDENT OTHER THAN EA ACC AUTO ONLY: AGG EXCESS LIABILITY ❑ OCCUR ❑ CLAIMS MADE ❑ DEDUCTIBLE ❑ RETENTION EACH OCCURRENCE AGGREGATE WORKERS COMPENSATION AND EMPLOYERS' LIABILITY ANY PROPRErOR / PARTNER / EXECUTIV OFFICER / MEMBER EXCLUDED? IM yes, describe under SPECIAL PROVISIONS balm ❑ TORY LIMITS I MITTS ❑ ER EL EACH ACCIDENT EL DISEASE - EA EMPLOYEE E.L. DISEASE - POLICY UMIT DESCRIPTION OF OPERATIONS / LOCATIONS / VEHICLES / EXCLUSIONS ADDED BY ENDORSEMENT / SPECIAL PROVISIONS Roofing Contractor Residential Rooting CERTIFICATE HOLDER Miami -Dade County Building Code Compliance 140 West Flagler Street 16th Floor, Suite 1603 Miami, F1 33130 ACORD 25 ( /®B) CANCELLA .•.N SHOULD ANY OF THE ABOVE DESCRIBED POLICIES BE CANCELLED BEFORE THE EXPIRATION DATE THEREOF, THE ISSUING INSURER WILL ENDEAVOR TO MAIL DAYS WRITFEN NOTICE TO THE CERTIFICATE HOLDER NAMED TO THE LEFT, BUT FAILURE TO DO SO SHALL IMPOSE NO - 'ION OR ustearnr OF ANY MO UPON THE INSURER, I15,A OR ATIVES. 1 1 Project Address Miami Shores Village 10050 N.E. 2nd Avenue NW Miami Shores, FL 33138 -0000 Phone: (305)795 -2204 Parcel Number Applicant 139 NW 102 Street Miami Shores, FL 33150- 113.1010220080 Block: Lot: CLEMENT DURU Owner Information Address Phone Cell CLEMENT DURU 139 NW 102 Street MIAMI SHORES FL 33150 -1231 Contractor(s) Phone CeII Phone QUALITY ROOFING CONTRACTORS 11(305)953-3333 (786)367 -2029 Type of Work: Re Roof Additional Info: TILE Classification: Residential Scanning: 4 Fees Due CCF DBPR Fee DCA Fee Education Surcharge Permit Fee - New Roof Scanning Fee Technology Fee Total: Amount $13.20 $4.88 $4.88 $4.40 $325.00 $12.00 $17.60 $381.96 Pay Date Pay Type Invoice # RF -3 -11 -40409 03/30/2011 Check #: 27336 $ 331.96 $ 50.00 03/22/2011 Check #: 27308 $ 50.00 $ 0.00 Amt Paid Amt Due Available Inspections: Inspection Type: Up Lift Report Tin Cap Final Roof Tile In Progress Roof Review Renailing Affidavit Cap Sheet , In consideration of the issuance to me of this permit, I agree to perform the work covered hereunder in compliance with all ordinances and regulations pertaining thereto and in strict conformity with the plans, drawings, statements or specifications submitted to the proper authorities of Miami Shores Village. In accepting this permit I assume responsibility for all work done by either myself, my agent, servants, or employes. I understand that separate permits are required for ELECTRICAL, PLUMBING, MECHANICAL, WINDOWS, DOORS, ROOFING and SWIMMING POOL work. OWNERS AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. Futhermore, I authorize the above -named contractor to do the work stated. March 30, 2011 Authorized Signature: Owner / Applicant / Contractor / Agent Building Department Copy Date March 30, 2011 1 Miami Shores Village rr Building Department T 73 10050 N.E.2nd Avenue, Miami Shores, Florida 33138 �dd Tel: (305) 795.2204 Fax: (305) 756.8972 MAR 2 2 2011 s�� INSPECTION'S PHONE NUMBER: (305) 762.4949 Y: ,„,„(a.„„ct,„ BUILDING PERMIT APPLICATION FBC 20 Permit Type: BUILDING Permit No. °' I I --466 Master Permit No; 710 " $02 Owner's Name (Fee Simple Titleholder) Clement Owner's Address 139 N.W. 102 Street Duru Phone # City Miami Shores State Fl Tenant/I.essee Name Email Zip 331 50 Phone # Job Address (where the work is being done) 1 3 9 N . W 1 0 2 Street City Miami Shores Village County Miami -Dade Zip 3 31 5 0 FOLIO /PARCEL# 1 1 —31 01 — 022 -0080 Is Building Historically Designated YES NO X Flood Zone Contractor's Company Name Qua lity Roofing Contractor, phone# ( 305) 953 -3333 Contractor's Address 13 8 0 0 N . W . ' 1st AVenue City Miami State F1 Zip 33168 Qualifier Name Carlos Arocho Phone# (786) 367 -2029 State Certificate or Registration No. RC 0 0 5 8 6 2 7 Certificate of Competency No. 0 0 0 01 7 8 8 9 Contact Phone Carlos or Marylou E_ qualityroofing88 @yahoo.com Architect/Engineer's Name (if applicable) Phone # reroof 2200sgft. Value of Work For this Permit $ 22,000.00 Square / Linear Footage Of WorkNew 1 8 0 0 sqf t . Type of Work: ['Addition DAlteration New Total 40QLI Demolition � Repair/Replace LLJJ Demo Describe Work: New contruction with colorthrutile. Reroof existing roof . ******* * * * * * * * * * * * *** * ** * * ** ** * *** ** ** Fees************* ** * * **** *** *** ** * * * * * * * ** * * **** Permit Fee $ CCF $ CO /CC $ Submittal Fee $ Notary $ Training/Education Fee $ Technology Fee $ Scanning $ Radon $ DPBR $ Bond $ Double Fee $ Violation date: • � Structural Review. $ Total Fee Now Due $ 1b51. cic4e See Reverse side -a Bonding Company's Name (if applicable) Bonding Company's Address City State Zip Mortgage Lender's Name (if applicable) Mortgage Lender's Address City State Zip Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRICAL WORK, PLUMBING, SIGNS, WELLS, POOLS, FURNACES, BOILERS, HEATERS, TANKS and AIR CONDITIONERS, ETC OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. "WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT." Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must promise in good faith that a copy of the notice of commencement and construction lien law brochure will be delivered to the person whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site for the first inspection which occurs seven (7) days after the building permit is issued. In the absence of such posted notice, the inspection will not be appro d and a reinspection fee will be charged. Signature/40'z ,L Owner or Agent The foregoing instrument was acknowledged before me this day of 4" ; i0 t.' , by whc(is pff_sanalttiown to me or who has produced As identification and who did take an oath. NOTARY PUBLIC: Sign: Print: My Commission * * * * * * * * * * * ** SION # P253276 it ,. :larch 16,2015 APPROVED BY Signature Contractor The foregoing instrument was acknowledged before me this ) 7 day of f' , 20 94 , by ecesritur , who is personally known to me or who has produced as identification and who did take an oath. Print: My Commission Expir-, "" Marylou Hernandez Commission #DD930046 ,,;.- Expires: OCT. 10, 2013 BONDED THRII ATLANTIC BONDING CO., INC. * * * * * * * * * * * ** ************************************************* ** **************** ************* Plans Examiner Zoning Engineer Clerk checked (Revised 07 /10107)(Revised 06/10/2009) Miami Shores Viiiage Building Department 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 OWNERS'S AFFIDAVIT OF EXEMPTION ROOF TO WALL CONNECTION HURRICANE MITIGATION RETROFIT FOR EXISTING SITE - BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES PERSUANT TO SECTION 553.844 F.S. To: Miami Shores Village Building Department Date: March 1, 2011 10050 NE 2nd Ave Miami Shores, Fl 33138 Re: Owner's Name: Clement Duru Property Address: 139 N.W. 102 Street Miami Shores, F1 33150 Roofing Permit Number: Dear Building Official: Clement Duru certify that I am not required to retrofit the roof to wall connections of my building because: The just valuation for the structure for purpose of ad valorem taxation is less than $300,000.00. Please attach proof of ad valorem taxation. o The building was constructed in compliance with the provisions of the Florida Building Code (FBC) or with the provisions of 1994 edition the South Florida Building Code (1994 SFBC) Signature L 6 W. v ZZ,L,7 Print Name State of Florida County of Dade The undersigned, being the first duly sworn, deposes and says that he/she is the owner for the above property mentioned. Swom to and subscribed before me thi � ,1 L wEtit lay of tvt ✓e ` 20 it • * MY COMMISSION ft DD 646761 1 4 IRES: March 16 q.,,. - ;o Services Notary Public, Sate of Florida at Large OU_ �- • When the just valuation of the structure for purpose of ad valorem taxation is equal to or more than $300,000.00, and the building was not constructed with FBC nor a 1994 SFBC. Then you must provide a building application from a General Contractor for the Roof to Wall connection Hurricane Mitigation. Revised on 5/21/2009 Property Information Map My Home Miami -Dade County, Florida Page 1 of 1 Property Information Map Aerial Photography - 2009 0= This map was created on 3/1/2011 1:36:41 PM for reference purposes only. Web Site © 2002 Miami -Dade County. All rights reserved. 28 ft Summary Details: Folio No.: 0800 SINGLE FAMILY RESIDENCE 11- 3101- 022 -0080 Pro.e : 139NW102ST Mailing ddress: 1 CLEMENT DURU &W BRENDA 139 NW 102 ST MIAMI SHORES FL 33150 -1231 Property Information: Primary Zone: 0800 SINGLE FAMILY RESIDENCE CLUC: 0001 RESIDENTIAL - SINGLE FAMILY Beds /Baths: 3/2 Floors: 1 Living Units: 1 Adj Sq Footage: 1,733 Lot Size: 8,100 SQ FT Year Built: 1981 Legal Description: GOLD CREST A SUB PB 21 -56 W1/2 OF LOT 17 & ALL OF LOT 18 BLK 1 LOT SIZE 75.000 X 108 OR 11130 -1070 0681 JERRY FEINGOLD Assessment Information: Year: 2010 ` 2009 Land Value: $64,872 $133,798 Building Value: $155,955 $167,628 Market Value: $220,827 $301,426 Assessed Value: $97,498 $94,935 Exemption Information: aTIME 2010 2009 Homestead: $25,000 $25,000 2q:7 Homestead: YES YES Taxable Value Information: Year: 2010 2009 Taxing Authority: Applied Exemption/ Taxable Value: Applied Exemption/ Taxable Value: Regional: $50,000/ $47,498 $50,000/ $44,935 County: $50,000/ $47,498 $50,000/ $44,935 City: $50,000/ $47,498 $50,000/ $44,935 School Board: $25,000/ $72,498 $25,000/ $69,935 http: / /gisims2 .miamidade.gov /myhome /printmap. asp? mapurl = http: / /gisims2.miamidade.gov... 3/1 /2011 SECTION R4402.13 HIGH VELOCITY HURRICANE ZONES — REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIONS R4402.13.1 Scope. As it pertains to the section, it is the responsibility of roofing contractor to provide the owner with the required roofing permit, and to explain to the owner the content of the section. The provisions of Section R4402 govem the minimum requirements and standards of the industry for roofing system installations. Additionally, the following items should be addressed as part of the agreement between the owner ant the contractor. ' 4he-designated= spaceindic ttes4hatthe- item -has been-exptairied Aesthetics - Workmanship: the workmanship provisions of Section R4402 are for the purpose of providing that the roof system meets the wind resistance and water instruction performance standards. Aesthetics (appearance) are not a consideration with respect to workmanship provisions. Aesthetic issues such as color or architectural appearance, that are not part of a zoning code, should be addressed as part of the agreement between the owner and the contractor. Renailing wood decks: When replacing roofing, the existing wood roof deck may have to be re iled in accordance with the current provisions of Section R4403. (The roof deck is usually concealed prior to removing the existing roof system). Common roofs: Common roofs are those which have no visible delin (i.e., townhouses, condominiums, etc.) In buildings with common roofs, the r owner s ould notify the occupants of adjacent units of roofing to be performed. pep /neighboring tractor n Exposed Ceiling: Exposed, open beam ceilings are where the u can e viewed from below. The owner may wish to maintain the architectural app nail penetration of the underside of the decking may not be acceptable. This pro g ®A. th � fnt i + %the a . ' earan e. Ponding water: The current roof system and /or deck of the building may not drain well may cause water to pond (accumulate) in low-lying areas of the roof. Pounding can be an indication of structural distress and may require the review of a professional structural engineer. Pounding may shorten the life expectancy and performance of the new roofing system. Pounding conditions may not be evident until the original roofing system is removed. Pounding conditions should be corrected. Overflow scuppers (wall outlets): It is required that rainwater flows off so that the roof is not o rioaded from a buildup of water. Perimeter /edge wall or other roof extension may block this discharge if overflow scuppers (wall outlets) are not provided. It may be necessary to install overflow scuppers in accorda r - with the requirements of Sections R4402, R4403 and R4413. Ventilation: Most roof structures should have some ability to vent natural airflow through the i tenor of the structure assembly (the building itself). The existing amount of attic ventilation shall not be reduced. It may be beneficial to consider additional venting which can result in extending the service life of the roo Owner /Age 's ignatu'e Date Revised on 7/9/2009 LD Contractor Signature Date Florida Building Code Edition 2 '?a HIGH Velocity Hurricane Zone Uniform Permit Application Form Tr'; Vg n a MAR w U 20U gi Section A (General Information) Master permit No. Process too. Contractor's Name Quality Roofing Contractor, Inc. Job Address 139 N.W. 102 Street ❑ Low Slope ❑ Asphaltic Shingles • ROOF CATEGORY Mechanically. Fastened Tile Mortar /Adhesave Set Tile ❑ Metal PaneUShingles ❑ Wood Shing ❑ Prescriptive BUR -RAS 150 ROOF TYPE gi New Roof ip Re- Roofing ❑ Recovering ❑ Repair ❑ Malnte ROOF SYSTEM INFORM Low Slope Roof Area (SF) • Steep Sloped Roof Area (SF) T N/A }ocE 2200sqft. Nrw 1 R00Gtgft 4000sqft. Q .IFCT TO COMPLIANCE WITH ALI_ FEDERAL. 11 AND COUNTY RULES AND REGULATIONS Section B (Roof Plan) Sketch Roof Plan: illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains. include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets. mnOMMIMMEMMEMMEMIMEMMIMMUMMEMMUMMEMIMMUMMUMME suem m m:M.MOMM■MMMMM ���M� ■M■■■■■ ■■■■■■■■ ■11■■■■ ■■■■■■■■111MO■���■■■■■>•■ imp ■■■■■M■■■■ y O■■■■ ■■■■■■■■■MME■MMM.■M■EHMH■■■■MEM ■■■■■■■■■MEMEM■■■■■■MM MEONME r MMM ■M■H■HEMM■■■■ ■■MM■MmMimmui■■mil■®im ■viii immommi'm^■■■ ■■■■ ■■■■■■■1•■■ ■M■ ■MM ■M■■ 1■MMINIM■■■ ■■■ M■■■ INI MMEM■■■■■■■■■ ■M ■M■ ■MM■■■ \M■ ■MPMEM■■■■■ ■■ MM■■■■■■ I■ M■■■■ ■■■■■■ ■■M■■■■■ ■M■■■\LNEM■■■■■■■ ■■■■■M■■■MM■■M■■MI IMMEMM■MMOMM.E Em= = =M■■■■■■■■ ■ ■■■■■■■► WMwMMMMMMM ■■■■■■■■■ ■M■■M■■■NSINIM■■■■■ ■■■■■>•■■M EM■■■■ ■■ ■ ■■■■ ■MM■ ■M■MMI■■■►■MEMM■■■■■ ■■■■ MM■■■ 1NMM■■■■■■ ■■■■■■ ■M■■ ■■M■■ ■MM■■SI■■■ ■M■■■ ■ ■■■■M■■MEMM \M■■■■■■ ■EMM � ENEM■MMM PAMM ■ail ■ ■M■■■■■ ■■■■■■■■■■ I■■■\■■■■■■■ MllitiMME M■■MMMMM■■■ ■'J ■■■■■ ■1•■ ■■■ MM■■■ M■ I■■■■►■■■ ■■■UMMMM ■MM■MMMMM■■■M'M ■■■■ ■■■ ■ ■■■■M■NEWMI ■■MSIms .__�: �:MEIMPP.E■■ ■M■■■■■■ ■■■■■ ■■■ ■ ■■ immi ■ ■I% ■■■■■>•■MM■Mitimmo ■ ■ ■■■■ommum■■ ■■■■■■■ irJ■IM ME MMME MM■■■ ■M ■M■ ■MMM■\\ ■M■■■M■MM■ ■M■ MEMEMMEMMINMEMMEMMEMEMEMMEMMEMEMMIWOMMEMMEMMEMEM EMMEMMINIMMIMMEMMEMMIUMMEMMEMMINIMMEMEMMEMAMMEMMME M■MIN■■■ ■M■■M■■M!MMCC :ii =M` MEMMEMM■MMMMA'M■■■■■■■ IMM■■i MMM■ ■■■■■■■■■IAM ■fi1M ■■MMMM■■ ■Mir ■ ■M ■ ■■■■ ■■■■ M■■■■■■■■■■■■ ■■i■ ■■■■■M■M■E■■ ■MM■■■■M■■■■■■■ Florida Building Code Edition - +! •7 HIGH Velocity Hurricane Zone Uniform Permit Application Form • Section D (Steen Sic. Roof Svstem) Roof System Manufacture Hanson Roof Tile Product Approval number 09-0928.03 Minimurn Design Wind PriesSures, If Applicable (From RAS 127 or Calculations): P7 :, -45.1 P2: -78.6 P3: -116.2 mum Design Pressure Product Approval Specific System 39.0 Method ofTileAUachenent: Polyfoam adhesive setting Deck Type: Type i9nde insulation: Steel) Sloped Roof Sys>> -, Descril)ti< n wood 5/8 plywood Roof Slope 3 :12 Fire Barrier: 1(1) 301b. ASTM D -226 I N/A I N/A Fastener Type >i<Spacing: 11 1/4" R/S nails 2„r ®/c 17" a0 /lc Ridge Ventilation? D Adhesive Type: self adhering Type Cap Sheet I Mean Roof Height 14 ' Roof (Polystick TU Plus IHanson Hacienda Tile Type & Size Drip Cap: P 3 X 3 26 ga. galvanized Florida Building Code Edition HIGH Velocity Hurricane Zone Uniform Pemlit Application Form Section E (Tile Cafc'Ulations) For moment based tiie systems, chose either Method 1 Or 2. Compared the values for M. with the values from m.. if the hi values are greater than or equal to the M. values, for each area of the roof, then the tiie attachment method is acceptable. Method 1 "Moment Based 111. Calculations Per RAS 127" (Pi: -45.1 x a. 0.32 =14.43) - NI, 7_29 =M., 7.14 Product Approval m, 39.0 (Pa: __7$„[5 x I-0.32=-254S- M, =m.s 1 R m Product Approval MI . Q (Pa: 11 F � x 3 r1 _ 7 19- Illy =111.0.292a. Pr:.,..! uct Approval Mr 0, Method 2 " Simplified Tile Calculation r Table Below" Required Morndnt of Resistance (Mr) From Table Below Product Approval Mf Mr Required Moment of Resistance* Mean Roof Height-i. Roof Slope 1 15' 20' 25' 30' _ 40' 212 34.4 38.5 38.2 39.7 42.2 - 3:12 32.2 34.4 38.0 37.4 38.8 4:12 30.4 32.2 33.8 35.1 37.3 " 5:12 28.4 30.1 31.8 32.8 - 34.9 8:12 28.4 28.0 29.4 30.8 32.4 7:12 24.4 25.8 27.1 28.2 30.0 - Appeals. * ust be used in conJuctiOn with a list of moment based the systems endorsed by the Broward County Board of Rules and For Uplift based tile systems use Method 3. Compare the values for F' the values for Fr : If the F' values are greater than or equal tootheF r values, for each area of the roof, then the tile attachment is acceptable. Method 3 "Uplift Based Tile Calculations Per S 127" (P,: x 1: = x w:= )- w: _x cos 6t =Fn _ Product Approval F' (P2• x 1: = t wry -w: x cos 0 =Fr _Product Approval F (Pa: x 1: _ x w:= )- w: x cos 9. =F , Product Approval F' Where to Obtain Information Description Symbol Design Pressure P1 or P2 or P3 Mean Roof Haigh H Where to find X127 Table 1 or by an engineering analysis prepared by P8 based on Job Site Roof Mope 0 Job Site Aerodynamic Multiplier ProducdApproval Restoring Moment due to Gravity Attachment Rem Required Moment Resistance Minimum Resistance mg Product Approve! Mr Product Approval M, Calculated Product Approval Required Tile Weight Tile Dimensions F. Calculated Product Apprcval I=Length Product Approval vim, All Calculations must be submitted to the Building Official at the time of permit application MIAMF COUNTY BUILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION NOTICE OF ACCEPTANCE (NOA) MIAMI -DADE COUNTY, FLORIDA METRO -DADE FLAGLER BUILDING 140 WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -2901 FAX (305) 375 -2908 Hanson Roof Tile 1340 SW 34th Ave Deerfield Beach, FL 33442 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by Miami -Dade County Product Control Division and accepted by the Board of Rules and Appeals (BORA) to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Division (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BORA reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Division that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Mason Hacienda Double Roll' Roof Tile LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This revises NOA No. 07- 0914.06 and consists of pages 1 through 5. The submitted documentation was reviewed by Alex Tigera. NOA No.: 09-0928.03 Expiration Date: 12/16/12 Approval Date: 11/18/09 Page 1 of 5 ROOFING ASSEMBLY APPROVAL Category: Sub Category: Material: Roofing Roofing Tile Concrete 1. SCOPE This approves a roofing system using Hanson Hacienda Roof Tile, as manufactured by Hanson Roof Tile in Hobe Sounr4 Florida and as described in Section 2 of this Notice of Acceptance. For the locations where the pressure requirements, do not exceed the values listed in section 4 herein. The attachment calculations shall be done as a moment based system. 2. PRODUCT DESCRIPTION Manufactured by Applicant Hanson "Hacienda" Dimensions Length: 1714" Width: 13" 1Z" thick Length: varies Trim Pieces Width: varies Varying thickness 2.1 EVIDENCE SUBMITTED Test Agency American Test Lab of South Florida PRI Construction Materials Technologies PRI Construction Materials Technologies IBA Consultants, Inc. Test Product S1�ecifications Description Low profile, interlocking, extruded concrete roof tile equipped with two nail hole and double roll ribs. For direct deck or battened nail -on, mortar or adhesive set applications. Accessory trim, concrete roof pieces for use at hips, rakes, ridges and valley terminations. Manufactured for each tile profile. Test Identifier RT0922.02 -09 HRT- 054 -02 -02 HRT- 054 -02 -01 2381 -249 TAS 112 TAS 112 Test Name/Renort TAS 102 TAS 101 TAS 101 TAS 112 D- 09/22/09 09/18/09 09/22/09 09/20/07 NOA No.: 09-0928.03 Expiration Date: 12/16/12 Approval Date: 11/18/09 Page 2 of 5 3. LIMITATIONS 3.1 Fire classification is not part of this acceptance. 3.2 For mortar or adhesive set tile applications, a static field uplift test in accordance with RAS 106 may be required, refer to applicable building code. 3.3 Applicant shall retain the services of a Miami -Dade County Certified Laboratory to perform quarterly test in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Building Code Compliance Office for review. 3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed section 4.1 herein. 3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated otherwise by the underlayment material manufacturers published literature. 3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with applicable building code. 4. INSTALLATION 4.1 Hanson `Hacienda' Roof Tile and its components shall be installed in strict compliance with Roofing Application Standard RAS 118, 119, & 120. 4.2 Data For Attachment Calculations Table 1: Average Weight (W) and Dimensions (I x w ) Tile Profile Weight W (Ibf) Length -1 (ft) Width w (ft) Hanson Hacienda 10.0 1.4375 1.08 Table 3: Restoring Moments due to Gravity - Ma (ft-Ibf) Tile Profile Table 2: Aerodynamic Multipliers - A. (fts) 3 ":12" Tile Profile 6 ":12" X (it) Batten Application X. (fts) Direct Deck Application Hanson Hacienda Direct Deck Direct Deck . N/A 0.32 Table 3: Restoring Moments due to Gravity - Ma (ft-Ibf) Tile Profile 2":12" 3 ":12" 4 ":12" 6 ":12" 6 ":12" r:12" or greater Direct Deck Hanson Hacienda Direct Deck Direct Deck . Direct Deck Direct Deck Direct Deck • 7.37 7.29 7.17 7.02 6.84 6.64 NOA No.: 09 -0928.03 Expiration Date: 12/16/12 Approval Date: 11 /18/09 Page 3 of 5 Table 4: Attachment Resistance Expressed as a Moment - Mf (ft-lbf) For Nall -On Systems Tile Profile Hanson Hacienda Fastener Type Direct Deck (min 15/32" plywood) Direct Deck (min. 19/32" plywood) Battens Two (2). # 8 x 3" Screws 35.9 35.9 Table 5: Attachment Resistance Expressed as a Moment - Mf (ft-lbf) For Two Patty Adhesive Set Systems Tile Application Tile Profile Hanson Hacienda Tile Bond N/A Minimum Attachment Resistance 1 Dow Chemical Tile Bond''Th". Two patty's of 11g were installed as per Tile Bond NOA. 44.41 Table 6: Attachment Resistance Expressed as a Moment - Mf (ft-Ibf) For Single Patty Adhesive Set Systems Tile Application Tile Profile Hanson Hacienda Polyfoam PolyProTA° Minimum Attachment Resistance 29.2` Polyfoam PolyProTM 2 Medium paddy placement of 24grams of PolyProTM AH -160. 3 Large paddy placement of 54grams of PolyProTM AH -160. 39.0' 5. LABELING All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo (See Detail Below), or following statement: "Miami -Dade County Product Control Approved ". Hanson HANSON HACIENDA ROOF TILE TILE IDENTIFICATION MARK (LOCATED ON UNDERSIDE OF TILE) 6. BUILDING PERMIT REQUIREMENTS 6.1 Application for building permit shall be accompanied by copies of the following: 6.1.1 This Notice of Acceptance. 6.1.2 Any other documents required by the Building Official or applicable building code in order to properly evaluate the installation of this system. NOA No.: 09- 0928.03 Expiration Date: 12/16/12 Approval Date: 11/18/09 Page 4 of 5 PROFILE DRAWINGS HANSON HACIENDA CONCRETE ROOF TILE FASTENER HOLES OVERLOCK l Pfr UNDERLOCK END OF THIS ACCEPTANCE NOA No.: 09- 0928.03 Expiration Date: 12/16/12 Approval Date: 11/18/09 Page 5 of 5 MIAMID BUILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION NOTICE OF ACCEPTANCE (NOA) Polyglass USA Inc. 150 Lyon Drive Fernley, NV 89408 MIAMI -DADE COUNTY, FLORIDA METRO -DADE FLAGLER BUILDING 140 WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -2901 FAX (305) 375 -2908 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by Miami -Dade County Product Control Division and accepted by the Board of Rules and Appeals (BORA) to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Division (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BORA reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Division that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code and the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION Pplystick P, Basik, IR/IRX, TIT, TU Plus, TUPolyester and- MU 'Underlayments LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement "Miami -Dade County Product Control Approved ", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA No. 06- 0505.01 and consists of pages 1 throu 6. The submitted documentation was reviewed by Jorge L. Acebo. NOA No.: 07- 1025.10 Expiration Date: 09/13/11 '- 'Approval Date: 04 /10/08 Page 1 of 6 ROOFING COMPONENT APPROVAL Category: Roofing Sub - Category : Underlayment Material: SBS , APP Self - Adhering Modified Bitumen PRODUCTS DESCRIPTION: Test Product Dimensions Specification Polystick P Roll: underlayment 75' x 3' 40 mils thick Polystick Basile Roll: underlayment 65'8" x 3'3-3/8" 60 mils thick Polystick IR/IRX underlayment Polystick TU underlayment Polystick TU Plus underlayment (Facer of Membrane Labeled in Orange or Black Ink) Polystick TU Polyester Polystick MU underlayment Product Description ASTM D 1970 A polyethylene top surface, self - adhering, SBS polymer modified bituminous sheet material for use as an underlayment in sloped roof assemblies. Designed as an ice & rain shield. ASTM D 1970 A homogeneous, rubberized asphalt waterproofing membrane, glass fiber reinforced with polyolefinic film on the upper surface for use an underlayment for metal roofing. A fine granular /sand top surface self- adhering, APP polymer modified, fiberglass reinforced, bituminous sheet material for use as an underlayment in sloped roof assemblies. Designed as an ice & rain shield and as a flat roof tile underlayment. TAS 103 and A heavy granuled surface self adhering, APP ASTM D 1970 polymer modified, fiberglass or polyester reinforced, bituminous sheet material for use as an underlayment in sloped roof assemblies. Designed as a a roof tile underlayment. TAS 103 and A non - wicking fabric surfaced, self - adhering, ASTM D 1970 APP polymer modified, fiberglass reinforced with a high strength polyester fabric, bituminous sheet material for use an an underlayment in sloped roof assemblies. Designed as a metal roofing and roof tile underlayment. TAS 103 A rubberized asphalt waterproofing membrane, glass- fiber /polyester reinforced, with a granular surface designed for use as a tile roof underlayment TAS 103 and A non - wicking fabric surfaced, self - adhering, ASTM D 1970 APP polymer modified, fiberglass reinforced, bituminous sheet material for use an an underlayment in sloped roof assemblies. Designed as a metal roofing and roof tile underlayment. Roll: TAS 103 and 65'8" x 3'33/8" ASTM D 1970 80 mils thick - Roll: 32'10" x 3'33/8" 100 mils thick Roll: 65'8" x 3,33/8„ 80 mils thick Roll: 32' 10" x 3'3 -3/8" 130 mils thick Roll: 65'8" x 3'3 -3/8„ 80 mils thick NOA No.: 07- 1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 2 of 6 EVIDENCE SUBMITTED: Test Agency • Test Identifier Test Name/Report Date Exterior Research & Design, LLC Trinity! ERD PRI Asphalt Technologies Momentum Technologies, Inc. #11756.04.01 -1 TAS 103 04/27/01 #11756.08.01 -1 ASTM D 1970 08/14/01 #02202.08.05 TAS 103 08/29/05 #P5110.08.07 TAS 103 08/29/07 PRI01111 ASTM D 4977 04/08/02 PUSA-005 -02 -01 ASTM D 4977 01/31/02 PUSA -018 -02 -01 ASTM D 2523 07/14/03 PUSA -035 -02 -01 TAS 103 09/29106 PUSA -033 -02 -01 ASTM D 1970 01/12/06 JX2OH7A ASTM D 4798 04/01/08 ASTM G 155 INSTALLATION PROCEDURES: Deck Type 1: Wood, non - insulated, new construction Base Sheet: One or more plies of ASTM D 226 Type II or ASTM D 2626 or Polyprotector UDL or Polyprotector UDL'AS. Fastening: Nails and tin caps 12" grid, 6" o.c. at laps. (for base sheet only) Membrane: Polystick membranes self-adhered. Surfacing: None 1. All nails in the deck shall be carefully checked for protruding heads. Re- fasten any loose decking panels, and sweep the deck thoroughly to remove any dust and debris prior to application. 2. Place the underlayment over metal drip edge in accordance with RAS 111. 3. Place the first course of membrane parallel to the eave, rolling the membrane to obtain maximum contact. Remove the release film as the membrane is applied . All side laps shall be a minimum of 3-W' and end laps shall be a minimum of 6." Roll the membrane into place after removing the release strip. Vertical strapping of the roof with Polystick is acceptable. Membrane shall be back nailed in accordance with applicable building code. 4. When applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane from the center outward in both directions. 5. For ridge applications, center the membrane and roll from the center outward in both directions. 6. Roll or broom the entire membrane surface so as to have full contact with the surface, giving special attention to lap areas. 7. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control Notice of Acceptance. 8. All protrusions or drains shall be initially taped with a 6" piece of underlayment. The flashing tape shall be pressed in place and formed around the protrusion to ensure a tight fit. A second layer of Polystick shall be applied over the underlayment. NOA No.: 07- 1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 3 of 6 GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance. 2. Polystick P, Basik and IR/IRX may be used in asphaltic shingles, wood shakes and shingles, non- structural metal roofing, and quarry slate roof assemblies. Polystick P and Basik shall not be used as roof tile underlayment. 3. Deck requirements shall be in compliance with applicable building code. 4. Polystick membranes shall be applied to a smooth, clean and dry surface. The deck shall be free of irregularities. 5. Polystick membranes shall not be adhered directly over a pre- existing roof membrane as a recover system. 6. Polystick P, Basik, IR/iRX, TU, TU Polyester and MU Underlayments shall not be left exposed as a temporary roof for longer than 30 days after application. Polystick TU Plus shall not be left exposed as a temporary roof for longer than 180 days after application. Polyglass reserves the right to revise or alter product exposure times; not to exceed the preceeding maximum time limitations. 7. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 9B -72 of the Florida Administrative Code. 8. In roof tile application, data for the attachment resistance of roof tiles shall be as set forth in the roof the manufacturer's Notice. Polystick TU, TU Plus and MU may be used in both adhesive set and mechanically fastened roof tile applications. Polystick IR/IRX is limited to mechanically fastened roof tile applications. Polystick TU Polyester may be used in both adhesive set and mechanically fastened roof tile. applications with the exception of mortar set tile applications. The maximum roof slope for use as roof tile underlayment for (direct -to- deck) tile assemblies shall be as described below: Tile Profile Polystick IR/IRX Polystick MU Polystick TU, TU Plus TU Polyester Flat Tile 5:12 No limitation No limitation Profiled Tile Prohibited 5:12 No limitation The above slope limitations can be exceeded only by using battens and counter battens in accordance with the Approved Tile System Notice of Acceptance and applicable Florida Building Code requirements. 9. Care should be taken during the loading procedure to keep foot traffic to a minimum and to avoid dropping of tile directly on the underlayment. Refer to Polyglass Tile loading detail for loading procedure. 0 0. 0 N 6 Roofing Tiles (6 Max. Per Stack) 12 NOA No.: 07- 1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 4 of 6 GENERAL L ATTIONS: (CONTINUED) 10. Refer to prepared roofing system Product Control Notice of Acceptance for listed approval of this product with specific prepared roofing products. Polystick P, Basik, IRJIRX, TU, TU Plus, TU Polyester & MU may be used with any approved roof covering Notice of Acceptance listing Polystick P, Basik, IR/IRX, TU, TU Plus, TU Polyester & MU as a component part of an assembly in the Notice of Acceptance. If Polystick P, Basik, TR/IRX, TU, TU Plus, TU Polyester & MU is not listed, a request may be made to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control Department for approval provided that appropriate documentation is provided to detail compatibility of the products, wind uplift resistance, and fire testing results. LABELING: 1.. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo and the following statement: Miami Dade County Product Control Approved" or the Miami Dade County Product Control Seal as shown below. BUILDING PERMIT REQUIREMENTS: Application for building permit shall be accompanied by copies of the following: 1. This Notice of Acceptance. 2. Any other documents required by the Building Official or applicable building code in order to properly evaluate the installation of this materials. POLYGLASS GENERAL APPLICATION GUIDELINES FOR POLYSTICK MEMBRANES: 1. Polyglass does accept the direct application of Polystick underlayment membranes to wood decks. Installers are cautioned to refer to applicable local building cafes prior to direct deck installation to ensure this is acceptable. Please also refer to applicable Product Data Sheets of the corresponding products. 2. All rolls, with the exception of Polystick TU Plus and Polystick MU should be back - nailed in selvage edge seam as per Polyglass Back Nailing Guide. Nails shall be, 11 gauge ring shank type, applied with a minimum 1" metal disk as required in Dade County or simplex type nail as otherwise allowable in other regions, at a minimum rate of 12" o.c. Polystick TU Plus and Polystick MU should be back nailed in designated area marked "nail area, area para clavar" on the face of membrane, with the above stated nails and/or disks. The head lap membrane is to cover the area being back nailed. (Please refer to applicable local building codes prior to installation.) 3. All seal lap seams (selvage laps) must be rolled with a hand roller to ensure full contact. 4. All fabric over fabric; and granule over granule end laps, shall have a 6" wide, uniform layer of Polyglass Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, Polyglass PG500 MB Flashing Cement, Mule -Hide 241 Premium Modified Flashing Cement, Mule -Hide 251 Premium Wet/Dry Elastomeric Flashing Cement, or Mule -Hide 421 Mod Bit Flashing Adhesive Trowel Grade mastic, applied in between the application of the lap. The use of mastic between the laps does not apply to Polystick Basik. 5. A maximum of 6 tiles per stack are allowed when loading tile on the underlayments Refer to the Polyglass Tile Loading Guidelines. NOA No.: 07- 1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 5 of 6 6. Battens and/or Counter - battens, as required by the tile manufacturers NOA's, must be used on all projects for pitch/slopes of 7 "712" or greater. It is suggested that on pitch/slopes in excess of 6 1/4 "/12 ", precautions should be taken, such as the use of battens to prevent tile sliding during the loading process. 7. Minimum cure time after membrane installation & before loading of roofing tiles is Forty-Eight (48) Hours. 8. Polystick TU Plus, Polystick MU may not be used in any exposed application such as crickets, exposed valleys, or exposed roof to wall details. 9. Repair of Polystick membranes is to be accomplished by applying Polyglass Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, Polyglass PG500 MB Flashing Cement, Mule Hide 241 Premium Modified Flashing Cement, Mule -Hide 251 Premium Wet/Dry Elastomeric Flashing Cement, or Mule -Hide 421 Mod Bit Flashing Adhesive Trowel Grade mastic to the area in need of repair, followed by a patch of the Polystick material of like kind should be set and hand rolled in place over the area needing such repair. Patching membrane shall be a minimum of 6 inches in either direction. The repair should be installed in such a way so that water will run parallel to or over the top of all laps of the patch. 10. All self- adhered membranes must be rolled to ensure full contact with approved substrates. Polyglass requires a minimum of 40 lbs for a weighted roller for the rolling of the field membrane. Hand rollers are acceptable for rolling of patches or small areas of the roof. 11. All approved substrates should be dry, clean and properly prepared, before any application of Polystick membranes commences. An approved substrate technical bulletin can be furnished upon request. It is .recommended to refer to applicable building codes prior to installation to verify acceptable substrates. 12. The Polyglass Miami Dade Notice of Acceptance (NOA) approval for Polystick membranes and PolyProtector UDL can be furnished upon request by our Technical Services Department by calling 1 (800) 894 -4563. 13. Polyglass offers a 10 year Limited Material Warranty on all properly installed Polystick self - adhered underlayments. Warranty must be requested and registered by Polyglass to be in force. 14. Questions in regards to the application of Polyglass products should be directed to our Technical Services Department at 1(800) 894 -4563. 15. Polyglass recommends that applicators follow good roofing practices and applicable procedures as outlined by the National Roofing Contractors Association (NRCA). PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF • SPECIFIC APPLICATIONS. LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS. END OF ::' S ACCEPTANCE NOA No.: 07- 1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 6 of 6 BUILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION NOTICE OF ACCEPTANCE (NOA) Polyfoam Products, Inc. 11715 Boudreaux Road Tomball, TX 77375 MIAMI -DADE COUNTY, FLORIDA METRO -DADE FLAGLER BUILDING 140 WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -2901 FAX (305) 375 -2908 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by the BCCO and accepted by the Building Code and Product Review Committee to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The BCCO (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BCCO reserves the right to revoke this acceptance, if it is determined by BCCO that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION- Polypro® A11160 j RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA No.01- 0521.02 and consists of pages 1 through 7 The submitted documentation was reviewed by JRrge L. Acebo. — NOA No.: 06- 0201.02 / Expiration Date: 05 /10 /11 Aiproval Date: 04 /13/06 Page 1 of 7 ROOFING ASSEMBLY APPROVAL: Category: Roofing Sub Category: Roof tile adhesive Materials: Polyurethane SCOPE: This approves Polypro® AH160 as manufactured by Polyfoam Products, Inc. as described in Section 2 of this Notice of Acceptance. For the locations where the design pressure requirements, as determined by applicable building code, does not exceed the design pressure values obtained by calculations in compliance with Roofing Application Standard RAS 127, for use with approved flat, low, and high profile roof tiles system using Polypro® AH 160. Where the attachment calculations are done as a moment based system for single patty placement, and as an uplift based system for double patty systems PRODUCTS MANUFACTURED BY APPLICANT: Product Dimensions Test Specifications Polypro ll AH 160 N/A TAS 101 FoamprolD RTF1000 ProPack® 30 & 100 N/A N/A Product Description Two component polyurethane foam adhesive Dispensing Equipment Dispensing Equipment PRODUCTS MANUFACTURED BY OTHERS: Any Miami Dade County Product Control Accepted Roof Tile Assembly having a current NOA which list moment resistance values with the use of Polypro A11160 roof tile adhesive. PHYSICAL PROPERTIES: Property Density Compressive Strength Tensile Strength Water Absorption Moisture Vapor Transmission Dimensional Stability Closed Cell Content Test ASTM D 1622 ASTM D 1621 ASTM D 1623 ASTM D 2127 ASTM E 96 ASTM D 2126 ASTM D 2856 Results 1.61bs./n.3 18 PSI Parallel to rise 12 PSI Perpendicular to rise 28 PSI Parallel to rise 0.08 Lbs./Ft2 3.1 Perm / Inch +0.07% Volume Change @ -40° F., 2 weeks +6.0% Volume Change @158°F., 100% Humidity, 2 weeks 86% Note: The physical properties listed above are presented as typical average valves as determined by accepted ASTM test methods and are subject to normal manufacturing variation. NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04 /13/06 Page 2 of 7 EVIDENCE SUBMI'1 "I ED: Test Agency Test Identifier Test Name/Report Date Center for Applied Engineering #94 -060 TAS 101 04/08/94 257818 -1PA TAS 101 12/16/96 25- 7438 -3 SSTD 11 -93 10/25/95 25- 7438 -4 25- 7438 -7 SSTD 11 -93 11/02/95 25 -7492 SSTD 11 -93 12/12/95 Miles Laboratories NB- 589 -631 ASTM D 1623 02/01/94 Polymers Division Ramtech Laboratories, Inc. 9637 -92 ASTM E 108 04/30/93 Southwest Research Institute 01- 6743 -011 ASTM E 108 11/16/94 01- 6739 -062b[1] ASTM E 84 01/16/95 Trinity Engineering 7050.02.96 -1 TAS 114 03/14/96 Celotex Corp. Testing Services 528454 -2 -1 TAS 101 10/23/98 528454 -9 -1 528454 -10 -1 520109 -1 TAS 10I 12/28/98 520109 -2 520109 -3 520109 -6 520109 -7 520191 -1 TAS 101 - 03/02/99 520109-2-1 LIMITATIONS: 1. Fire classification is not part of this acceptance. Refer to the Prepared Roof Tile Assembly for fire rating. 2. Polypro® AH 160 shall solely be used with flat, low, & high tile profiles. 3. Minimum underlayment shall be in compliance with the Roofing Application Standard RAS 120. 4. Roof Tile manufactures acquiring acceptance for the use of Polyprot AH160 roof tile adhesive with their tile assemblies shall test in accordance with TAS 101. 5. Roof Tile manufactures acquiring acceptance for the use of HANDI -STICK roof tile adhesive with their tile assemblies shall test in accordance with TAS 101 with section 10.4 as modified herein. t ,F: NOA No.: 06-0201.02 Expiration Date: 05 /10/11 Approval Date: 04 /13/06 Page 3of7 INSTALLATION: I. Polyproui AH160 may be used with any roof tile assetbiy having a current NOA that lists uplift resistance values with the use of Polypro® AH160. 2. Polypro® AH160 shall be applied in compliance with the Component Application section and the corresponding Placement Details noted herein. The roof tile assembly's adhesive attachment with the use of Polypro® AH160 shall provide sufficient attachment resistance, expressed as an uplift based system, to meet or exceed the uplift resistance determined in compliance with Miami bade County Roofing Application Standards RAS 127. The adhesive attachment data is noted in the roof tile assembly NOA 3. Polypr4 AH160 roof tile adhesive and its components shall be installed in accordance with Roofing Application Standard RAS 120, and Polyfoam Products, Inc. Polypro® AH160 Operating Instruction and Maintenance Booklet. 4. Installation must be by a Factory Trained 'Qualified Applicator' approved and licensed by Polyfoam Products, Inc. PoIyfoam Products Inc. shall supply a list of approved applicators to the authority having jurisdiction. 5. Calibration of the Foampro® dispensing equipment is required before application of any adhesive. The mix ratio between the "A" component and the "13" component shall be maintained between 1.0- 1.15 (A): 1.0 (B). The dispense timer shall be set to deliver 0.0175 to 0.15 pounds per the as determined at calibration. No other settings shall be approved. 6. Polypro® AH160 shall be applied with Foarnpro RTF1000 or I?roPack® 30 & 100 dispensing equipment only. 7. Polypro® AHI 60 shall not be exposed permanently to sunlight. 8. Tiles must be adhered in freshly applied adhesive. Tile must be set within 2 to 3 minutes after Polypro® AH160 has been dispensed. 9. Polypro® AH160 placement and minimum patty weight shall be in accordance with the Placement Details' herein. Each generic tile profile requires the specific placement noted herein. Table 1: Adhesive Placement For Each Generic Tile Profile Tile Profile Flat, Low, High Profiles High Profile (2 Piece Barrel) Flat, Low, High Profiles #2 Flat, Low, High Profiles #3 Placement Detail #1 #1 Single Paddy Weight Min. (grams) 35 17 /side on cap and 34 /pan 24 Two Paddy Weight per paddy Min. (grams) N/A N/A N/A 8 LABELING: All Polypro® AH 160 containers shall comply with the Standard Conditions listed herein. BUILDING PERMIT REQUIREMENTS; As required by the Building Official or applicable building code in order to properly evaluate the installation of this system. NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04/13/06 Page 4 of 7 ADHESIVE PLACEMENT DETAIL 1 SINGLE PATTY NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04 /13/06 Page 5 of 7 ADHESIVE PLACEMENT DETAIL 2 SINGLE PATTI( NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04/13/06 Page 6 of 7 ADHESIVE PLACEMENT ETAIL 3 DOUBLE PATTY END OF THIS ACCEPTANCE NOA No.: 06-0201.02 Expiration Date: 05/10/11 Approval Date: 04/13/06 Page 7 of 7