Loading...
RF-12-328Inspection Worksheet Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL Phone: (305)795 -2204 Fax: (305)756 -8972 Inspection Number: INSP - 170410 Scheduled Inspection Date: April 27, 2012 Inspector: Bruhn, Norman Owner: SYMES, ALEXIS & STEPHEN Permit Number: RF -2 -12 -328 Job Address: 313 NE 92 Street Miami Shores, FL 33138- Project: <NONE> Contractor: ACCORD ROOFING & CONSTRUCTION CORP Permit Type: Roof Inspection Type: Final Roof Work Classification: Tile Phone Number Parcel Number 1132060136360 Phone: (305)803 -2169 Building Department Comments TILE RE -ROOF Failed Correction Needed Re- Inspection Fee No Additional Inspections can be scheduled until re- inspection fee is paid. Inspector Comments April 27, 2012 For Inspections please call: (305)762.4949 Page 1 of 11 Roofing Contractor Job Address Owner's Name Type of Tile A -1 Engineering Inspection Services, Inc 7066 SW 44th Street Miami, Fl 33155 Tel: 786- 326 -9877 Fax: 305 -485 -9011 a1roofinspection@gmail.com LAB CERTIFICATION # 10- 0512 -01 SITE SPECIFIC INFORMATION UPLIFT TEST - TAS #106 ACCORD ROOFING 313 NE92ST Permit # SPANISH 5 Approximate Roof Height 24 feet Approximate Square Footage of Roof Date Tested 4/26/2012 Contact Name RICKY Date Installed Roof Pitch 3/12 Type of access to Roof 26 ft 2 Number of Tests 93 OK Required Testing Force 35 /bs Testing Equipment: F.G.E. 100 Phone # (305) 803-2169 LOCATION # OF TEST PASS # OF TEST FAIL Corner 19 Tests n Pass 0 Tests Fail Perimeter 29 Tests 5 Pass 0 Tests Fail Field 36 Tests If Pass 0 Tests Fail Ridge 9 - Tests 5 Pass 0 Tests 0 Fail Total 93 Tests Pass 0 Tests El Fail 5 IN ACCORDANCE WITH THE CRITERIA OF PROTOCOL PA 106, THIS ROOF ASSEMBLY HAS PASSED THE STATIC UPUFT QUALTTY CONTROL TEST. THIS TAS 106 TEST HAS BEEN PERFORMED IN FULL ACCORDANCE TO THE REQUIREMENTS OF DADE COUNTY, wrrH NO DEVIATIONS. THIS REPORT IS NOT GUARANTEED IN CASE OF NATURAL DISASTERS. Cordially REMBERTO CONTRERAS P.E P.E # 21522 A -1 ENGINEERING INSPECTION SERVICES INC CERTIFICATION NO 10- 0512.01 7066 SW 44th Street Miami, FI 33155 - Telephone (786)326 -9877 Fax (305)485-9011 A -1 Engineering Inspection Services, Inc 7066 SW 44th Street Miami, FI 33155 Tel: 786- 326 -9877 Fax: 305 - 485 -9011 alroofinspection @gmail.com LAB CERTIFICATION # 10- 0512 -01 SITE SPECIFIC INFORMATION UPLIFT TEST - TAS #106 Roofing Contractor ACCORD ROOFING Permit # Job Address Owner's Name 313 NE 92 ST Type of Tile SPANISH S Date Installed Approximate Roof Height 24 feet Roof Pitch 3/12 Type of access to Roof OK Required Testing Force 351bs Approximate Square Footage of Roof 26 ft 2 Date Tested 4/26/2012 Number of Tests 93 Testing Equipment: F.G.E. 100 Contact Name RICKY Phone # (305) 803-2169 SKETCH OF ROOF Revised by 7066 SW 44th Street Miami, FI 33155 Telephone (786) 326 -9877 Fax (305) 485 -9011 AFFIDAVIT OF COMPLIANCE WITH ROOF DECKING ATTACHMENT AND SECONDARY WATER BARRIER HURRICANE MITIGATION RETROFIT FOR EXISTING SITE -BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES PURSUANT TO SECTION 553.844 F.S. APR 3 O d2 BY To: Miami -Dade County Building Official lqg 2---"" 11805 Coral Way, Suite 111 Miami, FL 33175 Re: Owner's Name Property Address '313 of t 'l z S Roofing Permit Number �.. Z. , 1 Z -3 2 O Dear Building Official: I R Leev d � \44-Z certify that the roof decking attachment and fasteners have been strengthened and corrected and a secondary water barrier has been provided as required by the "Manual of Hurricane Mitigation Retrofits for Existing Site -Built Single Family Structures" adopted by the Florida Building Commission by Rule 9B -3.047 F.A.C. Qualifying Agen Signature of Q lifying Agent cAbst Print Name STATE OF FLORIDA COUNTY OF MIAMI-DADE Sworn to and subscribed before me this AI day of Oprt (SEAL) ,20 1 ".- t� Personally known or Produced Identification *112- tic,L h z. 51-1-11 Miami Shores Village qA,z112- Nc,4c Building Department 10050 N.E.2nd Avenue, Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 INSPECTION'S PHONE NUMBER: (305) 762.4949 BUILDING PERMIT APPLICATION FBC 20 67 Permit Type: BUILDING ROOFING Lis FEB. BY- Permit No. RT. k i? Master Permit No. OWNER: Name (Fee Simple Titleholder): f'g'on !11at -t3 Phone #: 776— 4J 2.— 9t9 Address: 2/ ? Art-f- 92.464 City: M t roiy�.i t � State: FL Zip: 77 a d Tenant/Lessee Name: Phone #: Email: VSi nos Pit 04 %/ r% ellark JOB ADDRESS: 7( 2 A[ 92Ia Jh.I City: Miami Shores Folio/Parcel #: County: Miami Dade Zip: ? ?/ 3a Is the Building Historically Designated: Yes NO Flood Zone: CONTRACTOR: Company Name: 4e'c O/d �lF C 1 Com Phone #: .30 oei ? z Wei Address: ‘2-71 <zv City: , �� State: P( Zip: ' 3 / 4' Qualifier Name: cCPi�(© Ci wvt'Z Phone #: In° 2 I State Certification or Registration #: CCC / 32 1(7 L Certificate of Competency #: Contact Phone #: 70 ^8l °2 / 1� e, Email Address: ��C C� �!` J V*. . 4 e A9'4 ea • �dwj DESIGNER: Architect/Engineer: Phone#: Value of.Work.f d; Type of Work: ❑A Description of Work: $ [� Square/Lrae�1Prk: ❑Alteration New ;,v, Repafr/R t ❑Demolition *• x******** *+ x+ x* *a :************ **m******** Fees*+ x*+ x*+ x***** ***+ x***** **** **a:**********x:**** ** Submittal Fee $ Permit Fee $ Scanning Fee $ Radon Fee $ Notary $ Training/Education Fee $ Double Fee $ Structural Review $ CCF $ CO /CC $ DBPR $ Bond $ Technology Fee $ TOTAL FEE NOW DUE $ Bonding Company's Name (if applicable) - Bonding Company's Address City State Zip Mortgage Lender's Name (if applicable) Mortgage Lender's Address City • State Zip Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRICAL WORK, PLUMBING, SIGNS, WELLS, POOLS, FURNACES, BOILERS, HEATERS, TANKS and AIR CONDITIONERS, ETC OWNER'S AI'N1DAVIT: I' certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. "WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT." Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must promise in good faith that a copy of the notice of commencement and construction lien law b chure will be delivered to the person whose property is subject to attachment. Also, a certified copy of the recorded notice of for the first inspection which occurs seven (7) days after the building permit is issued. inspection will not be app ved and a reinspection fee will be charged. Signature Owner or Agent The foregoing instrument was acknowledged before me this The foregoing instrument was acknowledged before me this rra day of I `'t , 20 19, by day of l 41 , 20 ! 2, by who is personally known to me or who has produced (lava/ who is personally known to me or who has produced As identification and who did take an oath. Signature cement must be posted at the job site the absence of such posted notice, the Contractor NOTARY Sign: Print: IC: PAOLO floritta WW1/ Asians Ole �1l J;t•�.li My Commission Expires: 7 /z/ i 2 as identification and who did take an oath. NOTARY PUBLIC: RRO Y'YhJ / • 053 Sign: , Inc Print: 2,4f3i) 4)461 „yr Commission Expires: al 13 ** ** x** **:x:x******* * *** x ***** *+ *** * * *** * **** �x:: x**** x: x�n�a�+ ��x***** a��x�x�:a�** **�x:��xw�x**** **** ��x�x�x�x +x�x *�xx�+x** ** *�x�x�x****+x� *** APPROVED BY `��%6/ J2S�`e*2 Plans Examiner Zoning Structural Review Clerk (Revised 07 /10 /07)(Revised 06 /10 /2009)(Revised 3/15/09) NOTICE OF COMMENCEMENT 1 11 1111 11111 11111 11 111 11111 11111 1111111111111 A RECORDED COPY MUST BE POSTED ON THE JOB SITE AT TIME OF FIRST INSPECTION PERMIT NO. TAX FOLIO NO. STATE OF FLORIDA: COUNTY OF MIAMI -DADE: STATE OF FLOR 1 HEIREFSY CE_PT1F THE UNDERSIGNED hereby gives notice that improvements will be made tp,cerin,('pal property, and in accordance with Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement. CFN 201 -i R.e i 176999 OR BI; 28030 F's 3149i RECORDED 03/12/2012 12:20:44 HARVEY RUVIHr CLERK OF COURT MIAMI -DADE COUNTYP FLORIDA LAST PAGE , COUOTY GF DADE 4C1 AD 21) l2. Uc'!INESS rhy hopd :'1 F.1oSf'1. HARVEY° WAN, C . ER6 °. a?1 j 7 C —T, a�1±riz Erp Space above reserved for use of recording office 1. Legal description of property and street/address: 3 t 3 dvE C3 2 , ® {V °)�1Yh,` �11 a4.1J If"1 13I.5'� 2. Description of improvement: re- weac� /1 Lc- 3. Owner(s) name and address: r< h 5 //'d?.« • Interest in property: 10 Name and address of fee simple titleholder: 4. Contractor's name, address and phone number: a tCcei t " P.0 7 5. Surety: (Payment bond required by owner from contractor, if any) Name, address and phone number: Amount of bond $ 6. Lender's name and address: 7. Persons within the State of Florida designated by Owner upon whom notices or other documents may be served as provided by Section 713.13(1)(a)7., Florida Statutes, Name, address and phone number 7ci sa 7 3y h-► r 33, 8. In addition to himself, Owners designates the following person(s) to receive a copy of the Lienor's Notice as provided in Section 713.13(1)(b), Florida Statutes. Name, address and phone number. 9. Expiration date of this Notice of Commencement: (the expiration date is 1 year from the date of recording unless a different date is specified) WARNING TO OWNER: ANY PAYMENTS MADE BY THE OWNER AFTER THE EXPIRATION OF THE NOTICE OF COMMENCEMENT ARE CONSIDERED IMPROPER PAYMENTS UNDER CHAPTER 713, PART I, SECTION 713.13. FLORIDA STATUTES, AND CAN RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE COMMENCING WORK OR RECORDING YOUR NOTI IF COMMENCEMENT. Signature(s) of Owner(s • r Owner )' A Prepared By / Print Name / /1Z'1, r 41 Title /Office C �! STATE OF FLORIDA COUNTY OF MIAMI -DADE e� The fo egoi� trument was acknowledged before me this 12 day of By "DT ✓� In‘ Q.elfY.t> ❑ Individually, or ❑ as for M4rsonally known, or ❑ produced the following type of identific Signature of Notary Public: Print Name: (SEAL) R- VERIFICATION PURSUANT TO SECTION 9Z525, FLORIDA .A ES= •- Under penalties of perjury, 1 • lare that 1 have read the foregog,ara. �' that the facts stated in It are t ' to the best of my knowledge °a�i ' Uef; *, < , p F9° {f ��F��� Signature(s) of Owner r r(s)'s Authorized Officer /Director! ner/Mana =*ho signed above: By By ` -'Q3 J0 L�A�1l��� orized Officer/Director/Partner/Manag Prepared By Print Name r� Title /Office 0 /4 Q . 01014. 123.01 -52 PAGE 3 12/11 02/27/2012 12:53 MORGAN INSURANCE 4 3057568972 n� CERTIFICATE OF LIABILITY INSURANCE PRODUCER Morgan Insurance Group • 13155 SW 42nd Street, Suite #107 Miami, FL 33175 Phone (305) 222 -9001 Fax (305) 222-9006 INSURED Accord Rooting & Construction Corp 15250 SW 23 St Miami, FL 33175 (305) 803 -2169 COVERAGES THE POLICIES OF INSURANCE LISTED HAVE BEEN ISSUED TO THE INSURED NAMED ABOVE FOR THE POLICY PERIOD INDICATED. NOTWITHSTANDING ANY REQUIREMENT, TERM OR CONDITION OF ANY CONTRACT OR OTHER DOCUMENT WITH RESPECT TO WHICH THIS CERTIFICATE MAY BE ISSUED OR MAY PERTAIN. THE INSURANCE AFFORDED BY THE POLICIES DESCRIBED HEREIN 18 SUBJECT TO ALL THE TERMS, EXCLUSIONS AND CONDITIONS OF SUCH POLICIES, AGGREGATE LIMITS SHOWN MAY HAVE BEEN REDUCED BY PAID CLAIMS. NO.876 1002 fl DATE (MM/DD/YY) 02/27/12 THIS CERTIFICATE IS ISSUED AS A MATTER OF INFORMATION ONLY AND CONFERS NO RIGHTS UPON THE CERTIFICATE HOLDER. THIS CERTIFICATE DOES NOT AMEND, EXTEND OR ALTER THE COVERAGE AFFORDED BY THE POLICIES BELOW. INSURERS AFFORDING COVERAGE NAIC 8 INSURER A: ATLANTIC INSURANCE CO INSURER B: INSURER C INSURER D: INSURER E INSURER F: INSR ADD'L LTR INSr.' TYPE OF INSURANCE POLICY NUMBER IPOLICY EFFECTIVE. • DATA (MMmom) POLICY EXPIRATION DATE (MMIODIYY) GENERAL LIABILITY ® COMMERCIAL GENERAL LIABILITY ❑ ❑ CLAIMS MADE © OCCUR 0 GEN'L AGGREGATE UMITAPPUES PER: ❑ POLICY ❑ PROJECT ❑ LOC 1003082 12'27/11 12/27/12 uIYiITS EACH OCCURRENCE 1,000,000 GAMAGE I 0 RETTED PREMISES (Ea OCCUronae) person) MED EXP (Any one 100,000 1,000 PERSONAL & ADV INJURY 1,000,000 GENERAL AGGREGATE 2,000,000 PRODUCTS - COMP/OP AGG 1,000,000 AUTOMOBILE LIABILITY ❑ ANY AUTO ❑ ALL OWNED AUTOS ❑ SCHEDULED AUTOS 12 HIRED AUTOS ❑ NON OWNED AUTOS COMBINED SINGLE LIMIT (Ea accident) BODILY INJURY (Par person) BODILY INJURY (Per accident) PROPERTY DAMAGE (Per accident) ❑ GARAGE LIABILITY ❑ ANY AUTO ❑ AUTO ONLY - EA ACCIDENT OTHER THAN EA ACC AUTO ONLY: AGG EXCESS UMBRELLA LIABILITY ❑ OCCUR ❑ CLAIMS MADE ❑ DEDUCTIBLE ❑ RETENTION $ WOR RS COMPENSATION AND EMPLOYERS' LIABILITY ANY PROPRIETOR/ PARTNER / EXECUTIVE OFFICER/ MEMBER EXCLUDED? If yes, describe under SPECIAL PROVISIONS below OTHER EACH OCCURRENCE AGGREGATE OT- TORY LIMIITT§ ❑ ERH • E.L EACH ACCIDENT EL DISEASE - EA EMPLOYEE El. DISEASE - POLICY LIMIT DESCRIPTION OF' OPERATIONS / LOCATIONS / VEHICLES / EXCLUSIONS ADDED BY ENDORSEMENT / SPECIAL PROVISIONS CERTIFICATE HOLDER CANCEU -ATION CITY OF MIAMI SHORES 10050 NE 2ND AVE MIAMI SHORES, FL 33138 SHOULD ANY OF THE ABOVE DESCRIBED POLICIES BE CANCELLED BEFORE THE EXPIRATION DATE THEREOF, THE ISSUING INSURER WILL ENDEAVOR TO MAIL. 30 DAYS WRITTEN NOTICE TO THE CERTIFICATE HOLDER NAMED TO THE LEFT, BUT FAILURE TO 00 30 SHALL IMPOSE NO OBLIGATION OR LIABILITY OF ANY KIND UPON THE INSURER,.ITS AGENTS OR REPRESENTATIVES. AUTHORIZED REPRESENTATIVE ACORD 25 (2001/08) OF @ACORD CORPORATION 1986 ROOF ASSEMBLIES AND ROOFTOP STRUCTURES siEcolt° FE8 twit ......... Florida Building Code Edition 2007 High- Velocity Hurricane Zone Uniform Permit Application. Form. Section A (General Information) Master Permit No. ]] R,00,4-1-05 Process No. Contractor's Name A Cef1(Q ©"/1 8 C &xiS ri c 4 ' Job Address 313 ALE 2" 5 1' -H -... ❑ Low Slope ❑ Asphaltic Shingles ❑ New Roof ❑ Mechanically Fastened Tile X Mortar /Adhesive Set Tile ❑ Metal PaneUShingles ❑ Wood Shingles /Shakes ❑ Prescriptive BUR -RAS 150 ROOF TYPE 111Reroofing ❑ Recovering ❑ Repair ROOF SYSTEM INFORMATION ❑ Maintenance Low Slope Roof Area (SF) Steep Sloped Roof Area (SF) Total (SF) Cf3 x553 Cpctinn B (Roof Plan) Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains. Include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets. 16 1 13 3 l 3 7.2 FLORIDA BUILDING CODE — BUILDING SECTION R4402.13 HIGH VELOCITY HURRICANE ZONES — REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIONS R4402.13.1 Scope. As it pertains to the section, it is the responsibility of roofing contractor to provide the owner with the required roofing permit, and to explain to the owner the content of the section. The provisions of Section R4402 govem the minimum requirements and standards of the industry for roofing system installations. Additionally, the following items should be addressed as part of the agreement between the owner ant the contractor. The owner's initial in the designated space indicates that the item has been explained. 1. J,�— Aesthetics - Workmanship: the workmanship provisions of Section R4402 are for the purpose of providing that the roof system meets the wind resistance and water instruction performance standards. Aesthetics (appearance) are not a consideration with respect to workmanship provisions. Aesthetic issues such as color or architectural appearance, that are not part of a zoning code, should be addressed as part of the agre,naent between the owner and the contractor. Renailing wood decks: When replacing roofing, the existing wood roof deck may have to be nailed in accordance with the current provisions of Section R4403. (The roof deck is usually concealed prior to rem ±ving the existing roof system). 3. , Common roofs: Common roofs are those which have no visible delineation between neighboring u, s (i.e., townhouses, condominiums, etc.) In buildings with common roofs, the roofing contractor and/or owner hould notify the occupants of adjacent units of roofing to be performed. Exposed Ceiling: Exposed, open beam ceilings are where the underside of the roof decking can viewed from below. The owner may wish to maintain the architectural appearance; therefore, roofing nail penetration of the underside of the decking may not be acceptable. This provides the option of maintaining the appea/ance. 5. , Ponding water: The current roof system and /or deck of the building may not drain well and may use water to pond (accumulate) in low -lying areas of the roof. Pounding can be an indication of structural distress and may require the review of a professional structural engineer. Pounding may shorten the life expectancy and performance of the new roofing system. Pounding conditions may not be evident until the origins roofing system is removed. Pounding conditions should be corrected. 6. Overflow scuppers (wall outlets): It is required that rainwater flows off so that the roof is not erloaded from a buildup of water. Perimeter /edge wall or other roof extension may block this discharge if overflow scuppers (wall outlets) are not provided. It may be necessary to install overflow scuppers in accordance with the requirements of Sections R4402, R4403 and R4413. 7. Ventilation: Most roof structures should have some ability to vent natural airflow through the i or of the structure assembly (the building itself). The existing amount of attic ventilation shall not be redu ' It may be beneficial to consider additional venting whic n result in extending the service life of the ro Agent' . 'l* ature D Revised on 7/9/2009 LD Contracto f•ignature a ROOF ASSEMBLIES AND ROOFTOP STRUCTURES Florida Building Code Edition 2004 High- Velocity Hurricane Zone Unlform Permit Application Form. Section D (Steep Sloped Roof System) Roof System Manufacturer: IC/1 V c Notice of Acceptance Number: _ d3Zq e2/ Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations): / P1: `f� • / P2: 7e 5. P3: —//6.2 Maximum Design Pressure 6 3 ' z• (From the Product Approval Specific System RootSlope: : 12 Steep Sloped Roof System Description Deck Type: /x& V- h,NT' Type Underlayment: Ridge V la itllpa n? Insulation: 30 FE z' Fire Barrier: Mean Roof Height if Fastener Type & Spacing: Adhesive Type: ,O -y'1 s Radif77.67/ , P8e/ /c4 Type Cap Sheet: Roof Covering: ceraimica vet c (ni b 5 Type & Size Drip Edge: 15.34 FLORIDA BUILDING CODE — BUILDING t 4 •F ROOF ASSEMBUES AND ROOFTOP STRUCTURES Florida Building Code Edition 2004 High - Velocity Hurricane Zone Uniform Permit Application Form. Section E (Tile Calculations) For Moment based tile systems, choose either Method 1 or 2. Compare the values for Mr with the values from Mt. If the Mf values are greater than or equal to the Mr values. for each area of the roof, then the tile attachment method is acceptable. Method 1 "Moment Based Tile Calculations Per RAS 127" (Pt: . /x 0.3 = /6* 49- Mg: /d/3,(, _ M,./433 Product Approval Mf 6 /.Z (P2:' /Ci• (/x 77 g lie- Mg: (0.310 = Mc2 Z.2.72. Product Approval Mf 63212'; (P37 /4.7x A7-1 =_1r - Mg 4 • '= M,,3 aks Sgt Product Approval Mf O3. 2/2" Method 2 "Simplified Tile Calculations Per Table Below" Requited Moment of Resistance (Mr) From Table Below Product Approval Mf Mr required Moment Resistance' Mean Roof Height -4. Roof Slope 4, 15' 20' 25' 30' 40' 2:12 34.4 38.5 38.2 397 42.2 3:12 32.2 34.4 38.0 37.4 39.8 4:12 30.4 32.2 33.8 35.1 37.3 5:12 28.4 30.1 31.8 32.8 34.9 8:12 28.4 28.0 29.4 30.5 32.4 7 :12 24.4 25.9 27.1 28.2 30.0 *Must be used in conjunction with a list of moment based tile systems endorsed by the Broward County Board of Rules and Appeals. For Uplift based file systems use Method 3. Competed the values for F' with the values for Fr. If the F' values are greater than or equal to the Fr values,. for each area of the roof, then the tile attachment method is acceptable. Method 3 "Moment Based Tile Calculations Per RAS 127" (P1 x = xw: = -W: x cos 8 =Fi (P2: xL = xw: -W: x cos0 =F2 (P3: xL xw: = -W: x cos0 =Fr3 Product Approval F' Product Approval F' Product Approval F' Where to Obtain Intonnatlon Description Symbol Where to find Design Pressure PI or P2 or P3 RAS 127 Table 1 or by an engineering analysis prepared by PE based on ASCE 7 Mean Roof Height H Job Site Roof Slope 0 Job Site Aerodynamic Multiplier A Product Approval Restoring Moment due to Gravity Mg Product Approval Attachment Resistance Mr Product Approval Required Moment Resistance Mu Calculated Minimum Attachment Resistance r Product Approval Required Uplift Resistance Fr Calculated Average Tile Weight W Product Approval The Dimensions L = length W = width Product Approval • All calculations must be submitted to the building official at the time of permit application. FLORIDA BUILDING CODE - BUILDING 15.35 'MIAMIDE COUNTY BUILDING AND NEIGHBORHOOD COMPLIANCE DEPARTMENT (BNC) BOARD AND CODE ADMINISTRATION DIVISION NOTICE OF ACCEPTANCE (NOA) Ceramica Verea Ctra. N-634 San Sebastian, Santiago, Km 683 Lanza S/N 15685 Mesia (Coruna) Spain MIAMI -DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 Miami, Florida 33175 -2474 T (786) 315 -2590 F (786) 315 -2599 www.miamldade.sov /building/ SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County BNC - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BNC reserves.the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Clay Spanish "S" Roof Tile LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This revises NOA # 08- 0111.02 and consists of pages I through 6. The submitted documentation was reviewed by Alex Tigera. NOA No.: 11-0329.01 Expiration Date: 03/13/13 Approval Date: 06/23/11 Page 1 of 6 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub Category: Roofing Tiles Material: Clay 1. SCOPE This approves a roofing system using Clay Spanish "S" Roof Tile manufactured by Ceramica Verea in San Sebastian, Spain and is distributed by Ceramica Verea, USA, as described in Section 2 of this Notice of Acceptance. For locations where the pressure requirements, as determined by applicable Building Code does not exceed the design pressure values obtained by calculations in compliance with RAS 127 using the values listed in section 4 herein. The attachment calculations shall be done as a moment based system. 2. PRODUCT DESCRIPTION Manufactured by Test Product Amlicant Dimensions Specifications Descrintion Clay Spanish "S" Roof L 19.6" ASTM C1167 High profile clay roof tile. For direct deck, Tile W =12.3" adhesive set applications. Trim Pieces Length: varies ASTM CI 167 Accessory trim, clay roof pieces for use at Width: varies hips, rakes, ridges and valley terminations varying thickness manufactured for each tile profile. 2.1 MANUFACTURING LOCATION 2.1.1. San Sebastian, Spain 2.2 EVIDENCE SUBMITTED Test Agency IBA Consultants, Inc. IBA Consultants, Inc. Test Identifier Test Name/Report Date 4709 -1 ASTM C 1 167 11/12/07 4709 -3 TAS 101 12/21/07 NOA No.: 11-0329.01 Expiration Date: 03 /13/13 Approval Date: 06/23/11 Page2of6 3. LINIITATIONS: 3.1 Fire classification is not part of this acceptance. 3.2 For mortar or adhesive set tile applications, a static field uplift test in accordance with TAS 106 may required, refer to applicable building code. 3.3 Applicant shall retain the services of a Miami -Dade County Certified Laboratory to perform quarterly test in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Building and Neighborhood Compliance Department — Product Control Section for review. 3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed section 4.1 herein. 3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated otherwise by the underlayment material manufacturers published literature. 3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with applicable building code. 4. INSTALLATION 4.1 Clay Spanish "S" Tile and its components shall be installed in strict compliance with Roofing Application Standard RAS -120. 4.2 Data For Attachment Calculations. Table 1: Average Weight (W) and Dimensions (I x w ) Tile Profile Weight -W (Ibf) Length -I (ft) Width -w (ft) Clay Spanish "S" Tile 8.4 1.633 1.025 Table 3: Restoring Moments due to Gravity - Ma (ft-Ibf) Table 2: Aerodynamic Multipliers - A (ft) 2 ":12" Tile Profile 4 ":12 "• A (ft3) Batten Application 6 ":12" A (ft3) Direct Deck Application Clay Spanish "S" Tile Direct Deck N/A Direct Deck 0.37 Table 3: Restoring Moments due to Gravity - Ma (ft-Ibf) Tile Profile 2 ":12" 3 ":12" 4 ":12 "• 5 ":12" 6 ":12" 7 ":12" or Greater Clay Spanish "S" Tile Direct Deck Direct Deck Direct Deck Direct Deck Direct Deck Direct Deck 6.46 6.36 6.21 6.01 5.74 5.40 Table 6: Attachment Resistance Expressed as a Moment - Mt (ft-Ibf) for Single Patty Adhesive Set Systems Tile Profile Tile Application Minimum Attachment Resistance Clay Spanish "S" Tile Polyfoam PolyProTM 63.212' . 1 Large paddy placement weight 34.6 grams of PalyProTM. MIAMI DADE COU APPROVED NOA No.: 11- 0329.01 Expiration Date: 03/13/13 Approval Date: 06/23/11 Page 3 of 6 5. LABELING 5.1 All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo as detailed below, or following statement: "Miami -Dade County Product Control Approved ". CERAMICA VERSA SA ESPANA LABEL FOR CLAY SPANISH "S" ROOF TILE (LOCATED ON THE SIDE OF TILE) 6. BUILDING PERMIT REQUIREMENTS: 6.1 Application for building permit shall be accompanied by copies of the following: 6.1.1 This Notice of Acceptance. 6.12 Any other documents required by Building Official or Applicable building code in order to properly evaluate the installation of this system. MIAMNDADE COUNTY APPROVED NOA No.: 11-0329.01 Expiration Date: 03/13/13 Approval Date: 06/23/11 Page 4 of 6 PROFILE DRAWING CLAY SPANISH S ROOF TILE END OF THIS ACCEPTANCE NOA No.: 11- 0329.01 Expiration Date: 03 /13/13 Approval Date: 06/23/11 Page 5 of 6 4 GREEN SUSTAINABLE ATTRIBUTES (GSA) SCOPE: This document is solely for the purpose of verification of Sustainable Attributes of construction materials. The documentation submitted has been reviewed by Miami -Dade County Product Control Section. Comnonent Name 1. Clay Spanish "S" Tile Initial Reflectance 0.39 Aged Reflectance Pending Initial Emmitance 0.83 Aged Emmitance Pending Solar Reflectance Index (SRI} 41 NOA No.: 11-0329.01 Expiration Date: 03/13/13 Approval Date: 06/23/11 Page 6 of 6 MIAM4C1iRlI,b COUNTY BIIILDING AND NEIGHBORHOOD COMPLIANCE DEPARTMENT (BNC) BOARD AND CODE ADMINISTRATION DIVISION NOTICE OF ACCEPTANCE (NOA) Polyglass USA Inc. 150 Lyon Drive Fernley, NV 89408 MIAMI -DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 Miami, Florida 33175 -2474 T (786) 315 -2590 F (786) 315 -2599 www.miamidade.gov/building/ SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County BNC - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BNC reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Polyglass Polystick Underlayments LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This renews and revises NOA # 09 -0806.07 and consists of pages 1 through 8. The submitted documentation was reviewed by Alex Tigera. MIAMMADE COUNTY APPROVED NOA No.: 11- 0601.10 Expiration Date: 09/13/16 Approval Date: 09/15/11 Page 1 of 8 ROOFING COMPONENT APPROVAL Category: Sub - Category: Material: Roofing Underlayment SBS , APP Self- Adhering Modified Bitumen PRODUCTS DESCRIPTION: Product Polystick MTS underlayment Manufacturing Location #2 Polystick IR -Xe underlayment Manufacturing Location #1 & #2 Polystick TU underlayment Manufacturing Location #1 & #2 Polystick TU Plus underlayment (Facer of Membrane with surface printing) Manufacturing Location #1 & #2 Polystick TU P underlayment Manufacturing Location #2 Polystick Tile Pro Manufacturing Location #2 Dimensions Roll: 65'8" x 3'33/8" 60 mils thick Roll: 65' x 3'33/8" Or 65' x 3' 80 mils thick Roll: 32' 10" x 3'33/8" 100 mils thick MIAMI•DADE COUNTY APPROVED Roll: 65' x 3'33/8" 80 mils thick Roll: 32' 10" x 3'33/8" 130 mils thick Roll: 61' x 3'33/8" 60 mils thick Test Product Specification Description TAS 103 A homogeneous, rubberized asphalt waterproofing membrane, glass fiber reinforced with polyolefinic film on the upper surface for use as an underlayment for metal roofing, roof tile, slate tiles and shingle underlayment. TAS 103 and ASTM D 1970 TAS 103 and ASTM D 1970 TAS 103 and ASTM D 1970 TAS 103 and ASTM D 1970 TAS 103 and ASTM D 1970 A fine granular /sand top surface self - adhering, APP polymer modified, fiberglass reinforced, bituminous sheet material for use as an underlayment in sloped roof assemblies. Designed as an ice & rain shield and as a flat roof tile underlayment. A heavy granuled surface self adhering, APP polymer modified, fiberglass or polyester reinforced, bituminous sheet material for use as an underlayment in sloped roof assemblies. Designed as a a roof tile underlayment. A non- wicking fabric surfaced, self - adhering. APP polymer modified, fiberglass reinforced with a high strength polyester fabric, bituminous sheet material for use an an underlayment in sloped roof assemblies. Designed as a metal roofing and roof tile underlayment. A rubberized asphalt waterproofing membrane, glass -fiber /polyester reinforced, with a granular surface designed for use as a tile roof underlayment. A rubberized asphalt self - adhering, glass - fiber /polyester reinforced waterproofing membrane. Designed as a metal roofing and roof tile underlayment. NOA No.: 11- 0601.10 Expiration Date: 09/13/16 Approval Date: 09/15/11 Page 2 of 8 PRODUCTS DESCRIPTION: Product Polystick Dual Pro Manufacturing Location #2 Dimensions Roll: 61' x 3'3-3/8" 60 mils thick MANUFACTURING PLANTS: 1. Hazelton, PA 2. Winter Haven, FL EVIDENCE SUBMITTED: Test Agency Exterior Research & Design, LLC Trinity I ERD PRI Asphalt Technologies Momentum Technologies, Inc. MIAMI•DADE COUNTY APPROVED Test Specification - ASTM D 1970 Test Identifier 11756.04.01 -1 11756.08.01 -1 02202.08.05 P5110.08.07 P 10870.09.08-RI P10870.04.09 P33360.06.10 P33370.03.11 P36900.09.11 PRI011 1 1 PUSA- 005 -02 -01 PUSA - 018 -02-0 l PUSA - 035 -02 -01 PUSA - 033 -02 -01 PUSA - 055 -02 -02 PUSA -083 -02 -01 PUSA -089 -02 -01 JX20H7A RX 14E8A DX23D8B DX23D8A Product Description A rubberized asphalt self - adhering, glass - fiber /polyester reinforced waterproofing membrane, specific for use as a high temperature underlayment. Designed as a metal roofing. Test Name/Report TAS 103 ASTM D 1970 TAS 103 TAS 103 TAS 103 TAS 103 /ASTM D4798 & G155 ASTM D1970 TAS 103 TAS 103 /ASTM D4798 & G155 ASTM D 4977 ASTM D 4977 ASTM D 2523 TAS 103 ASTM D 1970 TAS 103 TAS 103 TAS 103 /ASTM D4798 & G155 TAS 103 /ASTM D4798 & G155 TAS 103 /ASTM D4798 & G155 TAS 103 /ASTM D4798 & G155 TAS 103 /ASTM D4798 & G155 Date 04/27/01 08/14/01 08/29/05 08/29/07 12/04/08 04/13/09 07/01/10 03/02/11 09/01/11 04/08/02 01/31/02 07/14/03 09/29/06 01/12/06 12/10/07 06/30/08 07/06/09 04/01/08 11/09/09 02/18/10 02/18/10 NOA No.: 11- 0601.10 Expiration Date: 09/13/16 Approval Date: 09/15/11 Page 3 of 8 INSTALLATION PROCEDURES: Deck Type 1: Wood, non - insulated Base Sheet: One or more plies of ASTM D 226 Type 1I or ASTM D 2626. Fastening: Per FBC 1518.2 & 1518.4 Nails and tin caps 12" grid, 6" o.c. at a minimum 4" head lap. (for base sheet only) Membrane: Polystick membranes self - adhered. Surfacing: None 1. All nails in the deck shall be carefully checked for protruding heads. Re -fasten any loose decking panels, and sweep the deck thoroughly to remove any dust and debris prior to application. 2. Place the underlayment over metal drip edge in accordance with RAS 111. 3. Place the first course of membrane parallel to the eave, rolling the membrane to obtain maximum contact. Remove the release film as the membrane is applied. . All side laps shall be a minimum of 3 -1/2" and end laps shall be a minimum of 6." Roll the membrane into place after removing the release strip. Vertical strapping of the roof with Polystick is acceptable. Membrane shall be back nailed in accordance with applicable building code. 4. When applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane from the center outward in both directions. 5. For ridge applications, center the membrane and roll from the center outward in both directions. 6. Roll or broom the entire membrane surface so as to have full contact with the surface, giving special attention to lap areas. 7. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control Notice of Acceptance. 8. All protrusions or drains shall be initially taped with a 6" piece of underlayment. The flashing tape shall he pressed in place and formed around the protrusion to ensure a tight fit. A second layer of Polystick shall be applied over the underlayment. MIAMI•DADE COUNTY APPROVED NOA No.: 11- 0601.10 Expiration Date: 09/13/16 Approval Date: 09/15/11 Page 4 of 8 GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance. 2. Polystick MTS, TU Plus, and Tile Pro may be used in asphaltic shingles, wood shakes and shingles, non- structural metal roofing, roof tile systems and quarry slate roof assemblies. IR -Xe, TU, and TU P may be used in all the previous assemblies listed except metal roofing. Dual Pro may be used in all the previous assemblies listed except roof tile systems. 3. Deck requirements shall be in compliance with applicable building code. 4. Polyglass Polystick membranes shall be applied to a smooth, clean and dry surface. The deck shall be free of irregularities. 5. Polyglass Polystick membranes and underlayments shall not be adhered directly over a pre- existing roof membrane as a recover system. 6. Polyglass Polystick membranes shall not be left exposed as a temporary roof for longer than the amount of days listed in the table below after application. Polyglass reserves the right to revise or alter product exposure times; not to exceed the preceeding maximum time limitations. Exposure Limitations (days) Polystick MTS MTS IR Xe TU TU Plus TU P Tile Pro Dual Pro Winter Haven, FL. 180 180 180 180 180 180 180 Hazelton, PA. N/A 30 30 180 N/A N/A N/A 7. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 9B -72 of the Florida Administrative Code. 8. In roof tile application, data for the attachment resistance of roof tiles shall be as set forth in the roof tile manufacturer's Notice of Acceptance. Polystick TU and TU Plus may be used in both adhesive set and mechanically fastened roof tile applications. Polystick IR -Xe, and Tile Pro are limited to mechanically fastened roof the applications. Polystick MTS is limited to mechanically fastened with battens roof tile applications. Polystick TU P may be used in both adhesive set and mechanically fastened roof tile applications with the exception of mortar set tile applications. 9. The maximum roof slope for use as roof tile underlayment for (direct -to -deck) tile assemblies shall be as follows: (See Table Below) Tile Profile Polystick MTS Polystick IR -Xe Polystick TU, TU Plus, TU P, Tile Pro Flat Tile Prohibited without battens 5:12 No limitation Profiled Tile Prohibited without battens Prohibited No limitation The above slope limitations can be exceeded only by using battens and counter battens in accordance with the Approved Tile System Notice of Acceptance and applicable Florida Building Code requirements. Battens are required for both loading and installation of tiles at all times. MIAMI.DADE COUNTY APPROVED NOA No.: 11- 0601.10 Expiration Date: 09/13/16 Approval Date: 09/15/11 Page 5 of 8 GENERAL LIMITATIONS: (CONTINUED) 10. Care should be taken during the loading procedure to keep foot traffic to a minimum and to avoid dropping of tile directly on the underlayment. Refer to Polyglass' Tile loading detail below for loading procedure for all underlayments except Polystick MTS which shall be loaded onto battens. 11. Refer to prepared roofing system Product Control Notice of Acceptance for listed approval of this product with specific prepared roofing products. Polystick MTS, IR -Xe, TU, TU Plus, TU P, Dual Pro and Tile Pro may be used with any approved roof covering Notice of Acceptance listing Polystick MTS, 1R-Xe, TU, TU Plus, TU P, Dual Pro and Tile Pro as a component part of an assembly in the Notice of Acceptance. If Polystick MTS, 1R-Xe, TU, TU Plus, TU P, Dual Pro and Tile Pro is not listed, a request may be made to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control Department for approval provided that appropriate documentation is provided to detail compatibility of the products, wind uplift resistance, and fire testing results. LABELING: 1. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo, city and state of manufacturing facility and the following statement: "Miami -Dade County Product Control Approved" or the Miami -Dade County Product Control Seal as shown below. MANMADE COUNTY APPROVED BUILDING PERMIT REQUIREMENTS: Application for building permit shall be accompanied by copies of the following: 1. This Notice of Acceptance. 2. Any other documents required by the Building Official or applicable building code in order to properly evaluate the installation of this materials. MIAMNDADE COUNTY APPROVED NOA No.: 11- 0601.10 Expiration Date: 09/13/16 Approval Date: 09/15/11 Page 6 of 8 POLYGLASS GENERAL APPLICATION GUIDELINES FOR POLYSTICK MEMBRANES: 1. Polyglass does accept the direct application of Polystick underlayment membranes to wood decks. Installers are cautioned to refer to applicable local building codes prior to direct deck installation to ensure this is acceptable. Please also refer to applicable Product Data Sheets of the corresponding products. 2. All rolls, with the exception of Polystick TU Plus should be back - nailed in selvage edge seam as per Polyglass Back Nailing Guide. Nails shall be, 11 gauge ring shank type, applied with a minimum 1" metal disk as required in Dade County or simplex type nail as otherwise allowable in other regions, at a minimum rate of 12" o.c. Polystick TU Plus should be back nailed in designated area marked "nail area, area para clavar" on the face of membrane, with the above stated nails and/or disks. The head lap membrane is to cover the area being back - nailed. (Please refer to applicable local building codes prior to installation.) 3. All seal lap seams (selvage laps) must be rolled with a hand roller to ensure full contact. 4. All fabric over fabric; and granule over granule end laps, shall have a 6" wide, uniform layer of Polyglass Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, Polyglass PG500 MB Flashing Cement, Mule -Hide 241 Premium Modified Flashing Cement, Mule -Hide 25 I Premium Wet/Dry Elastomeric Flashing Cement, or Mule -Hide 421 Mod Bit Flashing Adhesive Trowel Grade mastic, applied in between the application of the lap. The use of mastic between the laps does not apply to Polystick MTS. 5. A maximum of 6 tiles per stack are allowed when loading tile on the underlayments. Refer to the Polyglass Tile Loading Guidelines. See General Limitations #9 and #10. 6. Battens and/or Counter- battens, as required by the tile manufacturers NOA's, must be used on all projects for pitch/slopes of 7 "112" or greater. It is suggested that on pitch/slopes in excess of 6'/ "/12 ", precautions should be taken, such as the use of battens to prevent tile sliding during the loading process. 7. Minimum cure time after membrane installation & before loading of roofing tiles is Forty-Eight (48) Hours. 8. Polystick membranes may not be used in any exposed application such as crickets, exposed valleys, or exposed roof to wall details. 9. Repair of Polystick membranes is to be accomplished by applying Polyglass Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, Polyglass PG500 MB Flashing Cement, Mule -Hide 241 Premium Modified Flashing Cement, Mule -Hide 251 Premium Wet/Dry Elastomeric Flashing Cement, or Mule -Hide 421 Mod Bit Flashing Adhesive Trowel Grade mastic to the area in need of repair, followed by a patch of the Polystick material of like kind should be set and hand rolled in place over the area needing such repair. Patching membrane shall be a minimum of 6 inches in either direction. The repair should be installed in such a way so that water will run parallel to or over the top of all laps of the patch. 10. All self - adhered membranes must be rolled to ensure full contact with approved substrates. Polyglass requires a minimum of 40 lbs for a weighted roller for the rolling of the field membrane. Hand rollers are acceptable for rolling of patches or small areas of the roof. Brooming may be used where slope prohibits rolling. 11. All approved substrates should be dry, clean and properly prepared, before any application of Polystick membranes commences. An approved substrate technical bulletin can be furnished upon request. It is recommended to refer to applicable building codes prior to installation to verify acceptable substrates. 12. The Polyglass Miami -Dade Notice of Acceptance (NOA) approval for Polystick membranes and PolyProtector UDL can be furnished upon request by our Technical Services Department by calling 1 (800) 894 -4563. MIAMIDADE COUNTY APPROVED NOA No.: 11- 0601.10 Expiration Date: 09/13/16 Approval Date: 09/15/11 Page 7 of 8 13. Questions in regards to the application of Polyglass products should be directed to our Technical Services Department at 1 (800) 894 -4563. 14. Polyglass recommends that applicators follow good roofing practices and applicable procedures as outlined by the National Roofing Contractors Association (NRCA). PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC APPLICATIONS. LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS. END OF THIS ACCEPTANCE MIAMI DADE COUNTY APPROVED NOA No.: 11- 0601.10 Expiration Date: 09/13/16 Approval Date: 09/15/11 Page 8 of 8 Property Information Map My Home Miami -Dade County, Florida Page 1 of 1 Property Information Map Aerial Photography - 2009 0 28 ft This map was created on 2/29/2012 11:07:08 AM for reference purposes only. Web Site © 2002 Miami -Dade County. All rights reserved. s?! Summary Details: Folio No.: 11- 3206 - 013 -6360 Property: 313 NE 92 ST Mailing STEPHEN N SYMES &W Address: ALEXIS POWELL Living Units: 313 NE 92 ST MIAMI Adj Sq Footage: ,4,129 SHORES FL Lot Size: 33138 -3133 Property Information: Primary Zone: 1100 SINGLE FAMILY RESIDENCE CLUC: 0001 RESIDENTIAL - SINGLE FAMILY Beds /Baths: 4/3 Floors: 2 Living Units: 1 Adj Sq Footage: ,4,129 $521,699 Lot Size: 12,700 SQ FT Year Built: 1927 $50,000/ $259,691 MIAMI SHORES SEC 1 City: AMD PB 10 -70 LOT 13 & Legal 14 BLK 47 LOT SIZE Description: 100.000 X 127 OR 17283 -4350 0796 1 OR 17283 -4350 0796 00 Assessment Information: Year: 2011 2010 Land Value: $158,758 $197,946 Building Value: $321,806 $323,753 Market Value: $480,564 $521,699 Assessed Value: $309,691 $305,115 Exemption Information: Year: 2011 2010 Homes $25,000 $25,000 2nd Homestead: YES YES Taxable Value Information: Year: 2011 2010 $250,000 Applied Applied Taxing Authority: Exemption/ Taxable Exemption/ Taxable Sales which are qualified Value: Value: Regional: $50,000/ $259,691 $50,000/ $255,115 County: $50,000/ $259,691 $50,000/ $255,115 City: $50,000/ $259,691 $50,000/ $255,115 School Board: $25,000/ $284,691 $25,000/ $280,115 Sale Information: Sale Date: 7/1996 Sale Amount: $250,000 Sale O /R: 17283-4350 Sales Qualification Sales which are qualified Description: View Additional Sales http: / /gisims2 .miamidade.gov /myhome /printmap .asp ?mapurl = http: / /gisims2 miamidade.go... 2/29/2012 A ICICARC/f • CERTIFICATE OF LIABILITY INSURANCE TEDA (MM/DDITYTY) . _ ________ • ;,* 03/13/12 THIS CERTIFICATE IS ISSUED AS A MATTER OF INFORMATION ONLY AND CONFERS NO RIGHTS UPON THE CERTIFICATE HOLDER. THIS CERTIFICATE DOES NOT AFFIRMATIVELY OR NEGATIVELY AMEND, EXTEND OR ALTER THE COVERAGE AFFORDED BY THE POLICIES BELOW. THIS CERTIFICATE OF INSURANCE DOES NOT CONSTITUTE A CONTRACT BETWEEN THE ISSUING INSURER(S), AUTHORIZED REPRESENTATIVE OR PRODUCER, AND THE CERTIFICATE HOLDER. IMPORTANT: if the certificate holder Is an ADDITIONAL INSURED, the pollcy(ies) must be endorsed. if SUBROGATION IS VVA1VED, subject to the terms and conditions of the policy, certain policies may require an endorsement. A statement on this cerftficate does not confer rights to the .cPr.0Pc.ate11Plcier1111Pu9f !Ych _NA.MP MIRIAM MESA PH014$ 221-7878- (305) 554-7090 Ext): (305) MIRIAMMESA@AOL.COM PRODUCER First Insurance Group 10967 SW.40 St Miami; FL 33165 Phone (305)221-7878 . . . PRODUCER • ER lfl# - Fax (305)554-7090 . _ .......... . . ......... INSURER(S) AFFORDING COVERAGE INSURED RICHMOM CONSTRUCTION 7066 SW 44. St • Miami, FL 33155- -1 INSURER A : AMERICAN SAFETY INDEMNITY • INSURER B: LIINN:vURREDER CD :: 305 INSURER E: INSURER F ________- . _ • COVERAGES CERTIFICATE NUMBER: REVISION NUMBER: ....... _ THIS IS TO CERTIFY THAT THE POLICIES OF INSURANCE LISTED BELOW HAVE BEEN ISSUED TO THE INSURED NAMED ABOVE FOR THE POLICY PERIOD INDICATED. NOTWITHSTANDING ANY REQUIREMENT, TERM OR CONDITION OF ANY CONTRACT OR OTHER DOCUMENT WITH RESPECT TO WHICH THIS CERTIFICATE MAY BE ISSUED OR MAY PERTAIN, THE INSURANCE AFFORDED BY THE POLICIES DESCRIBED HEREIN IS SUBJECT TO ALL THE TERMS, EXCLUSIONS AND CONDITIONS OF SUCH POLICIES. LIMITS SHOWN MAY HAVE BEEN REDUCED BY PAID CLAIMS. NAIC LTR TYPE OF INSURANCE ADDUSUBR POLICY NUMBER talpilAy) INEM.ANVD. • GENERAL LIABIUTY COMMERCIAL GENERAL mown. !LI D CLAIMS-MADE 0 OCCUR • A 156AUI85650 • • GENL AGGREGATE UNIT APPLIES PER POLICY n PRO- AuToi$GBILE LIABILITY • t ; 0 ANY AUTO • 0 ALL OWNED AUTOS 0 SCHEDULED AUTOS . El HIRED AUTOS I NON-OWNED AUTOS Is I-1 UMBRELLA LIAB • • • 0 OCCUR • • t I I • ! 1 EXCESS MB 0 CLAIMS-MADE 1LJDE0UC11BLE WORKERS COMPENSATION AND EMPLOYERS' UABIUTY `I/ N ANY PROPRIETORIPARTNER1EXECUTIVEr i • • OFFICER/MEMBER EXCLUDED? ;NM I (Mandatory in NH) Ifyes. describe under ' • IpTION flC OpERATIONS below I I . • - • • • • • LiMITS EACH OCCURRENCE i $ 1,000,000 NAGE TO RENTED , 1 I Ir2fignI;_E_S__(Euegc. urreacp)__ ' $ 100,000 _EIED EXP (Ancine person) ! $ 5,000. 02/04/2012 02/04/2013 , t PERSoNAL & ADV INJURY $ 1,000,000 FGENERAL AGGREGATE ! $ . 1,000,000 . _ I PRODUCTS - :OOMPOP G: ,:• . 1,000,000: — G _ $ _ . I COMBINED SINGLE . LIMIT ,• $ i (Ea accident) IBODILY INJURY (Per person) $ t BODILY INJURY (1,4,r accident)! $ PROPERTY DAMAGE $ • (Per accident) 18 I $ -L. I EACH OCCURRENCE $ I AGGREGATE $ $ -I $ 11---1 WC STATU- OTH-. ii-L.TORY_LIMIT.S.....L.J_ ER I • EL EACH ACCIDENT $ I. EL DISEASE - EAEMPLOYEE $ EL. DISEASE - POLICY UMIT DESCRIPTION OP OPERATIONS/ LOCATIONS / VEHICLES (Attach ACORD 101, Additional Remarks Schedule, it more space is required) GENERAL CONTRACTOR LIABILITY CERTIFICATE HOLDER CANCELLATION MIAMI SHORES VILLAGE 10050 NE 2 AVE MIAMI SHORES FL 33138-2382 ACORD 28(2009/09) QF SHOULD ANY OF THE ABOVE DES THE EXPIRATION DATE THEREOF', C WILL BE 0 ERED 04 ACCORDANCE WITH THE POLICY P ED POLICIES BE CANCELLED BEFORE AUTHORIZED REPRESENTATIVE ©1988-2009 ACORD CO7RTnire\‘. ‘' The ACORD name and logo' reserved. • f ACORD