Loading...
ROOFINGLG ENGINEERING SERVICES, INC. Consulting Engineers North Office: 7370 N.W. 36 Street Suite 374 Miami, Florida 33166 Tel: (305) 994 -8128 Fax: (305) 994 -8135 M. I. S. Corporation. 10220 Southwest 16 Street Miami, Florida 33165 Project: Dear Sirs; South Office: 13380 S.W. 131 Street Suite 120 Miami, Florida 33186 TILE UPLffTJEST Barber Residence 335 Northeast 101 Street Miami, Florida Information provided by client: Permit Number: 46688 Date Completion: June 9, 2000 Roofing Contractor: M. I. S. Corporation LG Engineering Services, Inc. Project Number: LG00 - 1117 (Testing Laboratory Certificate #00- 0224.07) c•1•v•1• E•N•G•I•N•E•E•R June 13, 2000 In accordance with your request and authorization, a representative of LG Engineering Services, Inc. completed the Roof Tile Uplift Test at the above referenced project. This testing was performed in general accordance with Roofing Application Standard RAS No.106 -- Standard procedure for field verification of the bonding of mortar or adhesive set tile system and mechanically attached, rigid, discontinuous roof systems. The total of the tested roof surface area was less than 5000 square feet, and the mean height of the roof is less than 20 feet above ground surface. The type of tile used for this project was reported to be Flat Roof Tile. This tile was reported to have been foamed in place. At the time of this testing, one test for every corner, one test for every 100 square feet of roof tile in the perimeter area and one test for every 200 square feet of roof tile in the field area were tested. Initially the entire area of the roof was examine for loose tile. More than 10% of the roof tile located in the field area and more than 20% of the roof tile at the roof perimeter and corner were physically examined. Based on our test results, we conclude that the installation of the roof title at; project meets the test requirement outlined in the above mentioned protoco a co o f our test report for your review ove referenced hed please find LG Engineering Services, Inc. appreciates the opportunity of assisting you in this project. If you have any questions or if we may be of further assistance, please do not hesitate to contact the undersigned. Respectfully submitted; LG Engineering Services, Inc. oha . d Sonny Sa11eti Proje t Manager TILE iJPLIELTEST Barber Residence 335 Northeast 101 Street Miami, Florida Test Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 • Test'Load (11) 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 est Status Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass LG Engineering Services, Inc. -- Tile Uplift Test Result -- Project Number: LGOO -1117, Page I Report of TILE UPLIFT TEST for Barber Residence 335 Northeast 101 Street Miami, Florida Project Number: LGOO-1117 Test Number 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 .Test Load .(1bfj;. 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass LG Engineering Services, Inc. Tile Uli t Test Result -- Project Number: L . .. Engineering Uplift o�ect Numbe . L000 -1117, Page 2 Test Number <> 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 Test Load !(lbf) 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 Test,Status Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass LG Engineering Services, Inc. -- Tile i Test Result -- Project Number: Page 3 LG00 -1117 Pag g Engineering � Ul Pf J � 8 North _>- 55 4- 0 t> pproximate Test. Location .. ..... _- : : :. :.. :::::: LG Engineering Services, Inc. -- Tile Uplift Test Result Project N umb b er: LG00- 1117 Page 4 • i PERMIT APPLICATION FOR MIAMI SHORES VILLAGE Date cif/ Job Address 335 A /0/ Tax Folio Legal Description Historically Designated: Yes No X Owner/Lessee / Tenant e n (/ /a/2t 1862— Master Permit # (b o ` 7 fb,c,7 i,5 O 7 Phone ‘306) — 758- /9 Owner's Address /k1 4 • Contracting Co. 0/24, Address Qualifier 4ZZ2 Phone &1- 9g7L Electrical Ins. Co. BOND Soo TOTAL DUE4 / f Engineering NOTICE OF COMMENCEMENT A RECORDED COPY MUST BE POSTED ON THE JOB SITE AT TIME OF FIRST INSPECTION PERMIT NO. TAX FOLIO NO. STATE OF FLORIDA: COUNTY OF DADE: OOR 193795 2000 APR 25 13:07 THE UNDERSIGNED hereby gives notice that improvements will be made to certain real property, and in accordance with Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement. 1. Legal _description of property and street address: c k/ 16/ 674" 4S ���" 67 'mss eg4ei4"4 ,?,9/0e G 4 I %se. escription of improvement: 3. Owner(s) name and address: 6'" C ' /a■a?Zba-/ a5 Ale /' / S9 ; P144a ,a /a S Interest in property: ;4.#J.&•Y el-/0777 tC Alf./04— G&V14 rL Name and address of fee simple titleholder: 4. Contractbr`s name and address: /1/1-. e&/ • Iref4V J1 /04: a / 4) 5 keett 46 5. Surety:(Payment bond require owner from contractor, if any) Name and address: Amount of bond $ 6. Lender's, name and address: 7. Persons within the State of Florida designated by Owner upon whom notices or other documents may be served as provided by Section 713.13(1)(a)7., Florida Statutes, Name and address: 8. In addition to himself, Owner designates the following person(s) to receive a copy of the Lienor's Notice as provided in Section 713.13(1)(b), Florida Statutes. Name and address: 9. Expiration date of this Notice of Commencement: (the expiration date is 1 year from the date of recording unless a different date is specified) X Signature of Owner Print Owners Name E Sworn to and subscribed before me this •21i day Notary Public Print Notary's Name �r r'. tn. Mv_nmmicc, c....:.. _Y -L �!� STATE OF FLORIDA, COUNTY OF DADE 1 HEREBY CERTIFV7hat this is o ft�e Copy of the original f A . , lhis of e on � rr WITNESS i y h HARVEY RtUV, ate By AZ' , A 0 20 Moot Seal. of Cu ounty Courts D.C. Prepared b .�� 1NILECH P y cjt T ExP. — � �i IP 3�ondexd Y S�rto�. # r .. Addr e s s : �s � 01- S/ No. CC5' (1 -/— 01‘ .33/,g157 As it pertains to this Appendix "F ". it is the responsibili:y the roolnw. contractor to provide the ow t :_; with the required roofing permit. to provide the owner with this appendix and w explain to the cw...ner the content of this form. The provisions of Chapter 34 of the South Florida Building Codc (SII3C) govern all the minimum requirements and standards of the industry for roofing system installations. Additionally. the following items should be addressed as part of the agreement between the owner and the contractor. The owner's initial in the adjacent box indicates that the item has been explained. 64 1. Aesthetics- Workmanship: The workmanship provisions of Chapter 34 are for the purpose of providing that the roofing system meets the wind resistance and water intrusion performance standards. Aesthetics (appearance) issues are not a consideration with respect to workmanship provisions. Aesthetic issues such as color or architectural appearance. that are not part of a zoning code, should b, addressed as part of the agreement betwten the owner and the contractor. e4 2. Ren:tiling Wood DYccks: When replacing roofing. the existing wood roof deck may have to be rettail_d in accordance with the current provisions of Chapter 29 of the SFBC. (The roof deco; is usually concealed.priv( to removing the existing roof system) (.../ '/ Common hoofs: Common roofs are those which have no visible delineation between neighboring units (i.e. townhouses. condominiums, etc.). In buildings with common roofs, the roofing contractor and /or owner should notify the occupants of adjacent units of roofing work to be performed. _ 4. Exposed ceilings: Exposed. open beans ceilings ore where the underside of the roof dcckin_, can be Viewed front blow. The owner may wish to ntattntain the architectural appearance. therefore, roofni• nail penetrations of the underside of the decking m'- not b_ acceptable. The SFBC provides the option of maintaining this appearance. ' S. I'onding \V;ttcr: The Curren[ roof 5vstent `nd!or deck of the t.uilding may not drain well *and may cause water to pond (accumulate) in low - lying areas of the roof. Ponding can b•; an indication of structural distress and may require the review of a profs ionsl structural engineer. Pondin_ may shorten the life exptcian_y and performance of thQ nee': roofr:tg Sysctm. P0:tdinlZ eoaditiiInS may not be evident until the ori_in0 roofing system is removed. Fonding conditions should b: corrected. '! 6. Overflow Scuppers (wall outlets): It is required that rainwater floe: off so that the roof is not overloaded from a build up of water. Perimeter /cdzc walls or other roof Extensions may block this discharge if overflow scuppers (wall outlets) are not provided. It may he necessary to install overflow scuppers in accordance with Chapter 23 of the SF2C. v , / 7. Ventilation: Most roof structures should have some ability to vent natural airflov through the interior of the structural assembly (the buiiding itself). The existing, amount of attic ventilation shall not be reduced. It may be beneficial to consider additional venting which can result in cxtcrtdint.: tltr scrCiCC life of the roof. S. The owner may contact the Miami•Dad_ County Consumer Services Department for further ornration reitardiris the above. APPENDIX "F" REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIO \S Ovncr's /Aecp't's Signature As it pertains to this Appendix "F ". it is the responsibility tiro ruofine Con:raewr to provide tile owt;et with the required roofing permit, to provide the owner with this appendix and to explain to the owner the content of this form. The provisions of Chapter 34 of the South Florida Building, Code (SFBC) govern all the minimum requirements and standards of the industry for roofing system installations. Additionally. the following items should be addressed as part of the aareernent between the owner and the contractor. The owner's initial in the adjacent box indicates that the item has been explained. 1. Aesthetics- \Yorkmnnchip: The cvorkinanship provisions of Chapter 34 are for the purpose of providing that the roofing system meets the wind resistance and water intrusion perfornttrnce standards. Aesthetics (appearance) issues are not a consideration with respect to workmanship provisions. Aesthetic issues such as color or architectural appcarutcc, that are not part of a 'zoning code, should be addressed is part of the aereem ent between the owner and the contractor. �, 2. Renniling Wood Peeks: \Vlicn replacing roofing. the existing wood roof deck rnuy have to be renailtd in accordance with -the current provisions of Chapter 29 of the SFBC. (The roof deck is usually concealecLprior to removing the existing roof system) / ' 3. Common Roofs: Common roo are those which have no visible delineation between neithborin_ units (i.e. townhouses. condominiums, etc.). in buildings v.ith common roofs, the roofing contractor and /or owner should notify the occupants of adjacent units of roofing work to be performed. 4. Exposed ceilings: Exposed. open beam ceilings are where the underside of the roof decking can be c le tve,i from below. The owner may wish to maintain the architectural appearance, therefore, roofrn• nail penetrations of the underside of the decking m . not be ■cccptabtc. The SFBC provides the option of maintaining this appearance. 5. Ponding Water: The current roof system and /or deck of tilt t.uildine may not drain well and may cause %voter to pond (accumulate) in low-lying are of the roof. Ponding can be an indication of structural distress and may require the re i w of a prof s =.1 structural cm :linter. Pondinc may shorten the life expectancy and performance of the tier: roofing system. Foadinr, conditions may not be evident until the ori` in.1 roofinc system is removed. Ponding conditions should be corrected. I . 6. Overflow Scup , ers (wall outlets): it is required that rainwater flow off so that the roof is not ,/ overloaded from a build up of water. Perimeter /edzc walls or other roof extensions may block this discharge if ovcrflo%v scuppers (wall outlets) are not provided. It may b_ necessary to install overflow.. scuppers in accordance with Chapter 23 of the $FEC. 7 7. Ventilation: tvtost roof structures should have some ability to vent natural airflow. throu_,h the interior of the structural assembly (thc building itself). The existin amount of attic ventilation shall not be reduced. It may be beneficial to consider additional venting which Can result in extending the service life of the roof. S. The owner may contact the t. County Consumer Services Department for further information rz_arding clic above. AFPENDiX '•F" REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIONS Ov ncr's /Agent'Es Signature di4 cite 'otrtr.rctor'$ Signature Contractor's Name: ❑ (Low Slope Application) ❑ (Asphalt/Fiberglass Shingles) 1 ,ln. ..... Appendix "E" UNIFORM ROOFING PERMIT APPLICATION PROCESS No. Job Address; ROOF CATEGORY ❑ (Nail -On Tile) CJ (Mon ❑ ( Metal RoofslWood Shingles & Shakes) ❑ (Other) ROOF PE ❑ New Roof Re roofing ❑ Recovering ❑ Repair ❑ Maintenance Flat Roof Arca (ft2j —'d Sloped Roof Area h' z o � u dg es ) • category ( ) r' -�`'�� Total (ft )G�� Master Permit No. Exposure cafe g (per ASCE 7 -88): Building Classification category b (Per ASCE 7 -88 table 1): "-= Fastener Ty Field: T ROOF HEIGHT AND SYSTEA1 DETAILS (Draw details as needed) TAC M NT SPA Perimeter: Corner: DETAIL t & 2 ct Tile) ROOF PLAN Owl 1 711*-1 • It er,ith.: e a* zl �- Rear..... Appendix "E" UNIFORM ROOFING PERMIT APPLICATION PROCESS No swPZD SYSTEM D3C1L YOA! Ptms s tope • web. (Aor/ K ( ...fj ram Mir q ) 1'� ) • (h.as3 x:31 em...,...s . ,.3 - ) . CRS Soot: `- amp «IM M S Imo, K. Ids PCA fie y.. M e 6 ?' - M � 1 PCA 1 S► ` M� 6•2-' Mrs �� PCA 5. is ..s if 4/4erdkoffit r r 4 4cSAOL Ser X .! . stir ATTACi1MSNTS REMMMO= 1) Fits ouaceoey Wm* Papa 2) Dads C wy holm Como! Nooks of A e pwoc -Corse Urn a) Sp c Ipusr Dssceepns. e) Specific Spent Ls canon c) Gerd Lawmen; o) Applicants Ociasi Drawings 3) Mai Fenno Apphcau.e 4 ) Met Csayonsn Animals 411 brie 01/13/99 12:08 MEDITERRANEAN ROOF TILE -, 3058999490 561 338 5391 03/09/98 NON 16 :07 FAX 561 336 5391 MONIER LIFETILE ma IA ACCEPTANCE NO.: 96- 0S28.06 Renews No. :24- 1221.08 NO. 209 101 METROPOLITAN DADE COUNTY. FLORIDA METRO -DADE FLAGLER BUILDING BUILDING CODE COMPLIANCE OFFICE METRO-OADE FLAGLER BUILDING 140 WEST FLAGLER STREET. SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -290 FAX (30S) 375.2908 PRODUCT CONTROL NOTICE OF ACCEPTANCE Monier Roof Tile 135 N.W.20 St. Boca Raton, FL 33431 Your application for Product Approval of: Bermuda Flat Tile under Chapter 8 of the Metropolitan Dade County Code governing the use of Alternate Materials and Types of Construction, and completely described in the plans, specifications and calculations as submitted by: Redland Technologies, The Center for Applied Engineering, Inc. and Professional Service Industries, Inc.. ' has been recommended for acceptance by the Building Code Compliance Office to be used in Dade County, Florida under the specific conditions set forth on pages 2 -12 and the standard conditions on page 13. This approval shall not be valid after the expiration date stated below. The Building Code Compliance Office reserves the right to secure this product or material at any time from a jobsite or manufacturer's plant for quality control testing. If this product or material fails to perform in the approved manner, the Building Code Compliance Office may revoke. modify, or suspend the use of such product or material immediately. The Building Code Compliance Office reserves the right to revoke this approval, if it is determined by the Building Code Compliance Office that this product or material fails to meet the requirements of the South Florida Building Code. The expense of such testing will be incurred by the manufacturer. EXPIRES: 01/08/01 Raul Rodriguez Product Control Supervisor THIS IS THE COVERSHEET, SEE ADDITIONAL PAGES FOIE SPECIFIC AND GENERAL CONDITIONS )BUILDING CODE c2MMITrEE This application for Product Approval has been reviewed by the Metropolitan Dade County Building Code Compliance Office and approved by the Building Code Committee to be used in •e County, Florida under the conditions set forth above- PRODUCT CONTROL DIVISION (305) 375.290 FAX (305) 372 -6339 Charles Danger, P.E. Director Building Code Compliance.Dept. APPROVED: 01/08/98 1 Metropolitan Dade County Internet mail address: Dost master(Apbuildingcodeontine.com Momepage:' httpJlwww .0uildingeodeonrine.com ®001 01/13/99 12:09 MEDITERRANEAN ROOF TILE -4 3058999490 03/08/88 NON 16:08 FAX 581 338 5381 MONIER LIFETILE Applicant: Monier Roof Tile 135 NW 20 St. Boca Raton, FL 33431 CateRorv: Sub- Cuteeorr. ,SO¢ -Type: PRODUCT CONTROL NOTICE OF ACCEPTANCE ROOFING SYSTEM APPROVAL Prepared Roofing Tile Mortar Set/Adhesive Set Concrete System Description Product Control No.: 96- 0528.06 Product Control No_: Approval Date: Expiration Date: 96- 0528.06 January 8, 1998 January 8.2001 Monier Roof Tile is a member of the Redland Group, a world wide producer of primary building products and roof tile. Monier manufacturers concrete roof tile for nail -on, mortar set or adhesive set applications in plants throughout the United States ranging from Washington State to Florida. MI tile is manufactured from extruded concrete consisting of Portland Cement, plasticizer, iron and metallic oxides, and blended aggregates. is Produc Con I Approval later to Monier's "Bermuda Flat" tile profile. Refer to appropriate Product Control Approvals for other tile pgoti1es. Monier sells tile systems through local distribution and directly to consumers. All profiles have matching trim pieces used for rake hip, ridge hip, and valley terminations. Tile system accessories such as underlayment, ventilation systems and flashing systems are also available. These accessories are manufactured for all profiles and form a part of this Product Control Approval. Moniees "Bermuda Flat" roof tile has been tested in compliance with the South Florida Building Code requirements for concrete, mortar or adhesive set tile applications. The minimum roof slope for Monier's "Bermuda Flat" mortar or adhesive set tiles shall be 2 ":12 ". See the "Profile Drawing" section in this approval for the "Bermuda Flat" profile drawing. The Monier "Bermuda Flat" tile profile has been tested for both wind characteristics and static uplift performance, therefore, any consideration for installation shall be done as a'Moment Based System'. Data for attachment calculations is noted in Tables 1 through 3 of this approval. Contact: Reese 14. Moody Technical Service Accessories Manager 135 N.W. 20 St. Boca Raton, FL 33431 (407)338-8200 Page 2 of 13 Frank Zutoaga Roofing Product Control Examiner NO.209 D02 1�j 01/13/99 12:09 MEDITERRANEAN ROOF TILE -; 3058999490 03/09/98 NON 16:09 FAX 561 338 5391 MONIER LIFETILE TRADE NAMES OF PRODUCT'S MANUFACTURED OR LABELED BY APPLICANT • Test Product Product Dimensions Specifications Dcscriptlon Bermuda Flat Flat I s 15" PA 112 Flat, interlocking, extruded Tile w = i0 3 /8" concrete roof tile equipped with I'/." thick two nails holes. For mortis Set or adhesive set applications. Trim Pieces . 1= varies PA 112 Accessory trim, concrete roof w = varies pieces for use at hips, rakes, ridges varying and valley terminations. thickness Manufactured for each tile profile. Page 3 of 13 Product Control No_. 96- 0528.06 Frank Zuloag3 Roofing Product Control Examiner NO. 209 903 ( 0003 01/13/99 12:09 MEDITERRANEAN ROOF TILE 4 3058999490 03/09/98 HON 16:09 FAX 561 338 5391 MONIER LIFETILE #30 Felt Product #43 Coated Base Sheet Mineral Surface Cep Sheet Rainproof 11 Ice and Water Shield TRADE NAMES OF PRODUCTS MANUFACTURED OTHERS Dimensions WA N/A WA Lenzingtex -ZB 140 59" x 164' roll Undcrlayment 22l.bs/roll 30 "x75'roll - 36" x 75' roll or 60 "x 75' roll 36" x 75' roll Test Specifications ASTM D 226 type II Product Description, Saturated organic felt to be used as a nailed anchor sheet. ASTM D 2626 Saturated and coated organic base sheet far single or double ply underlayrnent. ASTM D 249 Mineral surfaced asphalt roll roofing for use as a top ply in a double ply underlayment system. . PA 104 Single ply, nail -on underlayment. PA 104 Single ply, nail -on underlayment with 2" self-adhering top edge. PA 103 Self - adhering underlayment for use as a top ply ina two ply underlayment system with approved #30 or #43 as the base layer. Page 4 of l3 Product Control No.: 96- 0528.06 Manufacturer generic generic gwperic Lenzing Performance, Inc. PCA #94. 0527.05 Protect -O -Wrap, fnc. PCA #94- 0714.01 W.R. Grace Co. PCA 02-1116.01 Frank Zuloaga Roofing Product Control Examiner NO.209 PO4 a 00 01/13/99 12:10 MEDITERRANEAN ROOF TILE -, 3058999490 03/09/88 NON 16:09 PAX 561 338 5391 MONIER LIFETILE Product Mopping Asphalt Flashing Cement Asphalt Primer Roofing Nails Tin Caps Tile Nails Dimensions N/A N/A N/A min. 12 ga. with 3 /g" head min. 32 ga. min. 1 /g" o.d. max. 2" o_d_ min. 8d x 2W or min. 10dx3` Test Soeeifications ASTM 0 312 type Ill or IV ASTM D 4586 ASTM D 41 PA 114 Appendix E PA 114 Appendix E PA 114 Appendix E Page 5 of 13 Product Control No.: 96- 0528.06 Product Description Manufacturer Asphalt for bonding generic a mineral surface cap to a mech. attached base sheet in a double ply underlayment system. Cut back, asphalt based, asbestos free, fiber reinforced, trowel grade cement for repair and flashing applications. Cut back, asphalt based coating used to facilitate bonding of dissimilar materials. Annular ring shank, hot dipped, electro or mechanically galv. roofing nails for use in underlayment attachment. Corrosion resistant circular disc for use in underlayment attachment Corrosion resistant, screw or smooth shank nails for additional tile attachment at nave tile courses. generic generic generic generic generic Frank Zuloaga Roofing Product Control Examiner NO.209 D05 ®oos 01/13/99 12:10 r1EDITERRANEAN ROOF TILE i 3058999490 03/09/89 HON 18:10 FAX 581 338 5391 MONIER LIFETILE Product Roof Tile Monar ("TileTitc' ") Roof Tile Mortar ( "Quikrete® Roof Tile Mortar 01140 ") Roof Tile Mortar ( " Roof Tile Mortar Mix ") Roof Tile Adhesive (Polypro® AH160) Valley Flashing Drip Edge Dimensions N/A N/A N/A N/A min. 26 ga. min. 16" width min. 26 ga. min. 2" face flange min. 2" deck flange Test Specifications PA 123 PA 123 PA 123 PA 110 PA 111 Page 6of 13 Product Control No.: 96- 0528.06 Product Description Prepared mortar mix designed for mortar set roof tile applications. Prepared mortar mix designed for mortar set roof tile applications. Prepared mortar mix designed for mortar set roof tile applications. Adhesive designed for use in roof tile applications. ASTM A 525 Galvanized steel valley flashing Galvanized steel drip edge Manufacturer Bermuda Roof Company, Inc. I'CA #94- 0614.01 Quikrete Construction Products PCA #94- 0808.01 W.R. Bonsai Co. PCA #94- 0628.03 Polyfoam Products, Inc. PCAIU 94- 0401.01 generic generic Frank Zulougn Roofing Product Control Examiner NO. 209 P06 qb 008 01/13/99 12:10 MEDITERRANEAN ROOF TILE -> 3058999490 NO.209 1707 03/09/98 MON 16 :10 FAX 561 338 5391 MONIER LIFETILE 0007 Test Agency Test Identifier Test Name/Report Date The Center for Applied 94 -084 Static Uplift Testing May 1994 Engineering, inc. PA 101 (Mortar Set) The Center for Applied 94 -060A Static Uplift Testing March, 1994 Enigneering, loc. PA 101 (Adhesive Set) Redland Technologies P0631 -01 Wind Tunnel Testing July 1994 PA 108 (Mortar Set) Professional Service 224 -47099 Physical Properties Sept, 1994 Industries, Inc. PA 112 TEST REPORTS Page 7 of 13 Product Control No.: 96- 0528.06 Frank Zuloaga Roofing Product Control Examiner 01/13/99 12:10 MEDITERRANEAN ROOF TILE -' 3058999490 03/09/9.8 RON 16:10 FAX 581 338 5391 MONIER LIFETILE Deck Type: Deck Description: SYSTEM D: Slope Range: Underlayment: Roofing Tile: Comments: SYSTEMS Wood, Non - insulated New construction 19 /32" or greater plywood or wood plank. Mortar or Adhesive Set Application Page 8 of 13 Product Control No.: 96- 0528.06 2 ":12" to 7 ":12" Note: System D is only acceptable in this slope range. Install choice of approved underlayment system, noted on Page 1 of Dade County Protocol PA 120, in compliance with Section 3.02 of PA 120. Sec System Limitation #6. Install tile in compliance with PA 120 using one of the approved mortars or -adhesives noted in this approval. Mortar or adhesive shall be 'applied in compliance with the mortar manufacturer's Roofing Component Product Control Approval. The mortar or adhesive attachment shall provide sufficient attachment resistance expressed as a moment to meet or exceed the required moment of resistance determined in Compliance with PA 1 15 or PA 127. The mortar and adhesive attachment data is noted in Table 3, attached. 1. For re -roof applications, 15 /32" plywood is an acceptable substrate. 2. For mortar set applications, the first three courses of tile shall be nailed with not less than one nail per tile. As an alternate, the first three courses of tile shall be applied in mortar over a single layer of minimum 12 ga. wire mesh with square openings of not less than 3 /g" which is mechanically attached to the deck with not less than one roofing nail every 1 ft For roof pitches from 6 ":12" to 7 ":12", every third tile of every fifth course, beginning at the eighth course, shall be nailed with not less than one nail per tile.. Frank Zuloaga Roofing Product Control Examiner NO.209 008 e008 01/13/99 12:11 MEDITERRANEAN ROOF TILE i 3058999490 NO.209 009 03/09/98 NON 18:11 FAX 561 338 5391 MONIER LIFETILE ® 009 Page 9 of 13 Product Control No.: 96- 0528.06 SYSTEM LIMITATIONS 1. The standard minimum roof pitch for Monier "Bermuda Flat" mortar set or adhesive set tilt applications is 2" rise in 12" run (2 " ;12 "). The maximum roof pitch for mortar set or adhesive set tile applications is 7" rise in 12" run (7 " ;12 "). 2. Moniers "Bermuda Flat" tile profile has not becn tested for nail -on applications, therefore, System A (Counter - Batten Nail -On Application), System B (Direct Deck Nail - On Application) and System C (Horizontal Batten Nail -On Application) do not form pan of this approval. 3. System installation shall be in compliance with the system specifications outlined in this Product Control Approval. Mortar set or adhesive set tile shall be attached using an approved mortar or tile adhesive noted in this approval, the data of which is noted in Table 3 of this Approval. The method of attachment utilized shall provide sufficient attachment resistance expressed as a moment to meet or exceed the required moment of resistance determined in compliance with Dade County Protocol PA 115 or PA 127. 4. For mortar set applications. the first three courses of tile shall be nailed with not less than one nail per tile. As an alternate, the first three courses of tile shall be applied in mortar or adhesive over a single layer of minimum 12 ga. wine mesh with square openings of not less than 3/8" which is mechanically attached to the deck with not less than one roofing nail every 1 ft For roof pitches from 6 ":12" to 7 ":1 ", every third tile of every fifth course. beginning at the eighth course, shall be nailed with not less than one nail per tile. 5. For mortar set or adhesive set tile applications, a field static uplift test by a Dade County accredited testing agency, in compliance with Dade County Protocol PA 106, shall be required not less than 30 days after application to confirm tile adhesion. The results of this testing shall be reported to the Building Official and the installer stating that the application has passed or failed PA 106 testing. if tine application fails PA 106 testing, the report shall state which portion of the test was failed; Category 1 (examination for loose tile) or Category 2 (uplift testing of tile). Subsequent to testing, the installer may repair not more than 5% of field area tiles and 10% of perimeter area (i.e. ridge/rake) tile with approved tile adhesive. The installer shall place an identifiable marking on each repaired tile for future reference. Any PA 106 re - test shall not include any marked tile. 6. For mortar or adhesive set tile applications, 30/90 hot mopped underlayment applications may be installed perpendicular to the roof pitch prior to June 1, 1995 unless stated otherwise by the material manufacturer. Thereafter, 30/90 underlayment systems shall be installed parallel to the roof pitch in compliance with Appendix 'A' of Dade County Protocol PA 120. 7. All tiles shall bear the imprint or identifiable marking of the manufacturers name or logo for identification in the field. ' 8_ The Monier "Bermuda Flat" tile profile hes been tested for both wind characteristics and static uplift performance, therefore, attachment calculations for installation in compliance with Dade County Protocol PA 115 or PA 127 shall be done as a 'Moment Based System' uloaga Roofing Product Control Examiner 01/13/99 12:11 MEDITERRANEAN ROOF TILE 4 3058999490 NO. 209 P10 03/09/98 MON 16:12 FAX 561 338 5381 MONIER LIFETILE 10010 SYSTEM LIMITATIONS (CONTINUED) 9. Applications for rooting permits shall include a completed Section 11 of the Uniform Building Permit, a copy of Monier Roof Tile's current specifications and details, a copy of this Product Control Approval and a copy of the Product Control Approval of any Roofing Component used in the proposed tile application. Reference shall be made to appropriate data for the required fire rating. 10. The applicant shall retain the services of a Dade County certified testing laboratory to maintain quality control in compliance with the South Florida Building Code and related protocols. Samples taken shall be in compliance with Dade County Protocol PA 112, Appendix 'A'. 11. Any amendments to these provisions shall be in compliance with Sections 203 and 204 of the South Florida Building Code. Page 10 of 13 Product Control No.: 96- 0528.06 Frank Zuloaga Roofing Product Control Examiner u1/13/9 12:12 MEDITERRANEAN ROOF TILE i 3058999490 03/09/95 MON 18:12 FAX 581 338 5391 MONIER LIFEIILE Tile Profile Bermuda Flat Flat Tile Tile Profile Monier Bermuda Flat Tile Tile Profile Monier Bermuda Fiat Flat Tile DATA FOR ATTACRMENT CALCULATIONS Table 2: Restoring Momenta due to Gravity - M (ft -lbf) from PA 101 Testing 3 ":12" or - 4 5 ":12" 6 " :12" lese 5.20 5.12 5.01 4.89 Page 11 of 13 Product Control No.: 96- 0528.06 Table 1: Aerodynamic Multipliers - ? (ft') from PA 108 Testing X(ft X(ft') Batten A . • lication Direct Deck Ap ' Heaton N/A 0.24 Table 4: Attachment Resistance Expressed as a Moment - MI (ft -Ibt ) from PA 101 Testing Tile Attachment Application Resistance Mortar Set 39.00 Adhesive Set 118.90 7":12" or greater_ N/A rank Zutoaga Roofing Product Control Examiner NO. 209 D11 011 u1/1.6/ 12:12 r1ED 1 TERRANE ROOF TILE -; 3©5 999490 N0. 209 012 03/09/98 LION 18:12 FAX 581 338 5381 MONIER LIFETILE Z012 PROFILE DRAWING BEItMuDA FLAT FIAT TILE Page 12 of 13 Product Control No.: 96.0528.06 Frank Zuloaga Rooting Product Control Examiner 01/13/99 12:12 MEDITERRANEAN ROOF TILE -> 3058999490 03/08/88 MON 16:13 FAX 561 338 5391 MONIER LIFETILE 9 This Acceptance contains pages 1 through 13. END OF THIS ACCEPTANCE Page 13 of 13 Product Control No.: 96 -05aO6 Monier Roof Tile ACCEPTANCE NO.: 96- 0528.06 135 N.W. 206 St. APPROVED : January 8,1998 Boca Raton, FL. 33431 EXPJRFS : January 8, 2001 NOTIQir ACCEPTANCE STANDARD CONDITIONS 1 Renewal of this Acceptance (approval) shall be considered after a renewal application has been filed and the original submitted documentation, including test supporting data, engineering documents, are no older than eight (8) years. 2 Any and all approved products shall be permanently labeled with the manufacturer's name, city, state, and the following statement: "Metro-Dade County Product Control Approved ", or as specifically stated in the specific conditions of this Acceptance. 3 Renewals of Acceptance will not be considered if: a) There has been a change in the South Florida Building Code affecting the evaluation of this product and the'product is not in compliance with the code changes; b) The product is no longer the same product (identical) as the one originally approved; c) Tf the Acceptance holder has not complied with all the requirements of this acceptance, including the correct installation Of the product; d) The engineer who originally prepared, signed and sealed the required documentation initially Submitted, is no longer practicing the engineering profession. 4 Any revision or change in the materials, use, and/or manufacture of the product or process shall automatically be cause for termination of this Acceptance. unless prior written approval has been requested (through the filing of a revision application with appropriate fee) and granted by this office. 5 Any of the following shall also be grounds for removal of this Acceptance: a) Unsatisfactory performance of this product or process; b) Misuse of this Acceptance as an endorsement of any product, for sales, advertising or any other purposes. 6 The Notice of Acceptance number preceded by the words Metro-Dade County, Florida,: and followed by the expiration date may be displayed in advertising literature. If any portion of the Notice of Acceptance is displayed, then it shalt be done in its entirety. 7 A copy of this Acceptance as well as approved drawings and other documents, where it applies, shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job Site at all times. The copies need not be resealed by the engineer. 8 Failure to comply with any section of this Acceptance shall be cause for termination and removal of Acceptance. NO. 209 013 Z 013 0 41° 1.7ma'w. uloaga Roofing Product Control Examiner ACCEPTANCE NO.: 98- 0303.02 Renews: 96- 0402.02 EXPIRES: 04 /16/01 APPROVED: 04/16/98 Intornet meal address: po ,tmbster @buitdingcodeonllne.com METROPOLITAN DADE COUNTY. FLORIDA METRO -DADE FLAGLER BUILDING BUILDING CODE COMPLIANCE OFFICE METRO -DADE FLAGLER BUILDING 140 WEST FLAGLER STREET. SUITE 1603 MIAMi. FLORIDA 33130-1563 (305) 375-2901 FAX (305) 375.2908 PRODUCT CONTROL DIVISION (305) 375-2902 FAX (305) 372.6339 PRODUCT CONTROL NOTICE OF ACCEPTANCE Polyfoam Products, Inc. 2400 Spring - Stuebner Road Spring. 'i'X. 77383 Your application for Product Approval of: o • am o H s 11 -160" Roof Tile Adhesive under Chapter 8 of the Miami -Dade County Code governing the use of Alternate Materials and Types of Construction, and completely described in the plans, specifications and calculations as submitted by: The Center for Applied Engineering, Inc. and Miles Laboratories Polymers Division has been recommended for acceptance by the Building Code Compliance Office to bc used in Dade County, Florida under the specific conditions set forth on pages 2 -14 and the standard conditions on page 15. This approval shall not be valid after the expiratinn date stated below. The Building Code Compliance Office reserves the right w secure this product or material at any time from a jobsite or manufacturer's plant I"or quality control testing. If this product or material fails to perform in the approved manner. the Building Code Compliance Office may revoke, modify, or suspend the use of such product or material immediately. The Building Code Compliance Office reserves the right to revoke this approval. if it is determined by the Building Code Compliance Office that this product or material fails to meet the requirements of the South Florida Building Code. The expense of such testing will be incurred by the manufacturer. aul Rodriguez Product Control Supervisor THIS IS THE COVERSHF.F.T, SEE ADDITIONAL PAGES FOR SPECIFIC AND GENFRAi. CONDITIONS BUILDING CODE COMMITTEE This application for Product Approval has been reviewed by the Miami•Dade County flu ikling Code Compliance Office and approved by the Building Code Committee to bc uscd in Dade County, Florida under the condih^ous set forth above. Charles Danger. 1'.E. Director Building Code Compliance Dept. Miami -Dade County Homepage: http :Nwww.buildingcodeonllne.conr H11 POLY FOAM PRODUCTS, INC. PRODUCT CONTROL NOTICE OF ACCEPTANCE HOOFING COMPONENT APPROVAL App licant: . Polyfoam Products, Inc. 2400 Spring - Stuebner Road Spring. Texas 77383-1132 Category: Sub- Casefory, Sub-Tvpc: Roofing Component Fastening/Adhesive Roof Tile Adhesive Two Component Polyurethane System Description Product Control 140.: 98- Q303.0 Product Control No.: 98- 0303.02 Approval Date: April 16. 1998 Expiration Date: April 16. 2001 Polyfoam Products, Inc.. produces two- component expanding polyurethane adhesive for the attachment of clay and concrete roof tile. Polypro® AH 160 is specialty designed for application of concrete and clay roof tile over a variety of roof deck substrates and underlayment materials. Polypro® adhesive is applied with proprietary Foampro® RTF 1000 dispensing equipment. Approval of this product is specific to the two component mix and Foampro® RTFI000 dispensing equipment. Alternative methods of dispensing will require a revision to this approval. I'ulypro® adhesive shall be applied only by 'Qualified Applicators'. licensed by Polyfoam Products. Inc. Certificates and identification cards are issued to applicators upon successful completion of a application training program. Approval of this adhesive system is contingent upon application by a 'Qualified Applicator. Contact: Pat Murray P.O. Box 1132 Spring, Texas 77383.1D2 Phone: (713)350 -8 Fax: (713)288 -6 Rage 2 of 15 Frank Zutoaga, RRC Roofing Product Control Examiner H`JI - .�v �_... Page 3of15 Product Control No.: 98- 0303.02 POLYFOAM PRODUCTS, INC. TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT Test Product r. ecirations Dcscrin 'on oduct Dt"�e�sionss c Two component r Polypro® AH l60 N/A PA 101 polyurethane Foampro® RTF 1000 N/A See Detail Attached Dispensing Equipment Frank Zuloaga, RRC Roofing Product Control Examiner Apr -30 -98 04:11P Polyfoam Products Inc. 954 475 -1462 Product Underlayinent Roof Tile Test Criteria Product Description Page 4 of 15 Product Control No.: 98- 0303.0 POLYFOAM PRODUCTS, INC. TRADE NAMES OF PRODUCTS MANUFACTURED BY OTHERS Manufacturer PA 120 All Dade County Component Approved All Dade Count products as detailed in Dade County County Application Standard l'A 120 Approves PA 101 All Approved roof tile systems having All Dade tested in compliance with Dade County County Protocol PA 101, as detailed in the systems Approved section of this Component Approval Products Frank Zutoaga, RRC Roofing Product Control Examiner P -o5 POLYFOAM PRODUCTS, INC. Product Control No.: 98- 0303.02 TEST REPORTS Pest A>;encv_ Test Identifier Test Name/Report Date Center for Applied #94 - 060 Miami Dade Protocol 04/08/94 Engineering PA 101 Center for Applied 257818 - I PA Miami Dade Protocol 12/16/96 Engineering PA 101 Center for Applied 25 7438 - 3 SSTD 11 - 93 10/25/95 Engineering Center for Applied 25- 7438 -4 SSTD 11 -93 10/25/95 Engineering Center for Applied 25- 7438 -7 SSTD 11 -93 11/02/95 Engineering Ccntcr for Applied 25 - 7492 SSTD 11 - 93 12/12/95 Engineering Miles Laboratories NB -589 -631 ASTM D 1623 02/01/94 Polymers Division Ramtech Laboratories, 9637 -92 ASTM E 108 04/30/93 Inc. Southwest Research 01- 6743 -01 I ASTM E 108 11/16/94 Institute Southwest Research 01- 6739- 062b(I} ASTM E 84 01/16/95 Institute Trinity Engineering 7050.02.96 -1 PA 114 03/14/96 Page 5 of 15 Frank Zuloaga, RRC Roofing Product Control Examiner Apr - - 04:11►' YO lye .ran. r • �+�+ -��- - - - POLYFOAM PRODUCTS, INC. Property c t Density ASTM D 1622 Compressive ASTM D 1621 Strength Tensile Strength ASTM U 1623 Water Absorption ASTM U 2127 Moisture Vapor ASTM 1:96 Transmission Dimensional ASTM U 2126 Stability TYPICAL PHYSICAL PROPERTIES ASTM D 2856 86% Page 6of15 Product Control No.:_9tt-0j0 Results 1.6 lbs./ft.' 1A PSI Parallel to rise 12 PSI Perpendicular to rise 28 PSI Parallel to rise 0.08 Lbs. /Ft 3.1 Perm / Inch +0.07% Volume Change @ -40 F., 2 weeks +6.0% Volume Change ®158 100% Humidity, 2 weeks Closed Cell Content Note: The physical properties listed above are presented as typical average values as determined by accepted ASTM test methods and are subject to normal manufacturing variation. Frank Zuloaga, RRC Koofing Product Control Examiner POLYFOAM PRODUCTS. INC. Page 7 of 15 Product Control No.: 98- 043.02 SYSTEMS Deck Type: Wood. Non - insulated. New Constriction /Reroof Deck Description: 15 /;2 " or greater, plywood or wood plank. SYSTEM A: Adhesive Set Application Slope Range: 2 ":12" to 7 ":12" Underlayment: Shall comply with Miami -Dade Roofing Application Standard PA 120 Roofing Tile: Any roof tilt assembly having a current shall be applied in compliance with the Component Application section and the corresponding Placement Details of this Notice of Acceptance. The adhesive attachment shall provide sufficient attachment resistance expressed as a moment to meet or exceed the required moment of resistance determined in compliance with Miami -Dade County Roofing Application Standards PA 115 or PA 127. The adhesive attachment data is noted in the roof tile assembly NOA. Comments: 1. All 'System Limitations' noted in the tile Roof System Assembly Product Control Approval shall apply. Frank Zuloaga, RRC Roofing Product Control Examiner Apr -30 -98 04:12P Polyfoam Products Inc_ POLYFOAM PRODUCTS, INC- Deck Type: Deck Description: SYSTEM B: Stripe Range: Underlaymcnt / Waterproofing: Undcrhtyment: Roofing Tile: Comments: Concrete, New Construction /Retouf Ncw construction SYSTEMS (CONTINUED) 954 475 -1462 P.09 Adhesive Set Application 2 ":12" to 7":12" Install Approved underlaymcnt system of one of the following: (30/90 Hot Mop) fully adhered in a full mopping of ASTM U 312 type IV asphalt applied within the EVT range. Back nailing and laps shall be in compliance with Roofing Application Standard PA 120. Any liquid applied roofing system having a current NOA for its use as a tile undcrlayrnent system. Any roof tile assembly having a current shall be applied in compliance with the Component Application section and the corresponding Placement Details of this Notice of Acceptance. The adhesive attachment shall provide sufficient attachment resistance expressed as a moment to meet or exceed the required moment of resistance determined in compliance with Miami-Dade County Roofing Application Standards PA 115 or 1'A 127. The adhesive attachment data is noted in the roof tile assembly NOA. 1. All 'System Limitations noted in the tilt Roof System Assembly Product Control Approval or waterproofing component Roofing Component Product Control Approval shall apply, as applicable. Page 8 of 15 Product Control No.:_g8 0343.0 Frank Zutoaga, RRC Roofing Product Control Examiner Table 1: Adhesive Placement For Each Generic Tile Profile Tile Profile Placement Detail Two -Piece Barrel #I 'S' Shaped #2 Double Roll #3 Flat # % . 1 7 i - 2 _ '_, .. ...... . ...._7 ........ - • - - -- -- POLYFOAM PRODUCTS, INC. COMPONENT APPLICATION 1. Polypro® A14160 the adhesive shall only be applied over an undcrlayment installed in compliance with application instructions detailed in its NOA.. Underlayment may be any underlaymcnts or underlayment systems listed Miami -Dade County Roofing Application Standard PA 120. 2. Adhesive application shall be in accordance with the instructions provided herein. Title manufacturer may provide additional instructions subsequent to this approval date which may prevail. Installation must be by a Factory Trained 'Qualified Applicator' approved and licensed by Polyfoam Products. Inc. 3. Calibration of the Foampro® dispensing equipment is required before application of any adhesive. The mix ratio between the "A" component and the "B" component shall be maintained between 1.0- 1.15 (A) : 1.0 (R). The dispense timer shall be set to deliver 0.08 to 0.15 pounds per tile as determined at calibration. No other settings shall be approved without revision of NOA. 4. Adhesive shall be dispensed in a 17 in to 23 in' pad at time of application. The cured pad shall be approximately 5" x 12 ". Foam placement shall be in accordance with the Placement Details' herein. Each generic tile profile requires a specific placement, as noted in Table 1, below 5. Adhere tile directly in freshly applied adhesive. Tile must be set within 2 to 3 tninutes after foam has been dispensed. Page 9oft5 Product Control No.: 911- 0303.02 Frank Zuloaga, ItKC Roofing Product Control Examiner Apr -30 -98 04:13P Po lyroam Proouca.s POLYFOAM PRODUCTS, INC. Page 10 of 15 Product Control No.: 98- 0303.02 SYSTEM LIMITATIONS 2. Polypro® AH160 adhesive shall be installed only by 'Qualified Applicators' approved and licensed by Polyfoam Products, Inc. 3. For adhesive set tilt applications, a field static uplift test by a Miami -Dade County accredited testing agency. in compliance with Miami -Dade County Roofing Application Standard PA 106, shall be required not less than 72 hours after application to confirm tile adhesion. 4. Refer to application drawings published by the National Tile Manufacturers Association for penetrations and terminations, as well as the 'Placement Details' included with NOA. 5. Refer to tile Roof Tile Assembly Product Control NOA for system acceptance with this Component. 6. Refer to the Prepared Roof Tile Assembly for fire rating. 7. Polypro® AH160 shall not be exposed permanently to sunlight. 8. Polypro® AHI60 shall be applied with Foantpro RTF1000 dispensing equipment only. 9. Polyfoam Products Inc. shall supply Building Official with a list of'Qualificd Applicators' approved and licensed by Polyfoam Products, Inc. Frank Zuloaga, RRC Roofing Product Control Examiner Apr -3U - J a VV:•tir rv POLYFOAM PRODUCTS, INC. PLACEMENT DETAILS Placement Detail #1: Two-Piece Barrel Profile Page 11 of 15 Product Control No.: 98- 0303.02 Frank Zuloaga, RRC Roofing Product Control E.xarnincr Apr - - Uv 1•r ru .y. vc...• • . •• - - -- POLYFOAM PRODUCTS, INC. Doll .M•r.b pr•••• <w••••• tA... •w••1.•, by co• PLACEMENT DETAILS (CONTINUED) Optima apumeme Page 12of15 wf .*MI. .•• 1. ..M... •T 1. 22 equate Iwdr 4 .antra PAID Ow n• d..Y1. erode Dosed Placement Detail 1$2: '$' Shaped Tile Profile Product Control No.: 9g- 0303.02 .•f1..1.. Delp COD. • Frank Luloaga. RRC: Roofing Product Control Examiner Apr -30 - 9 U4 : 1 bI' F'O lyl Liam POI.YFOAM PRODUCTS, INC. Moll .. --./w !1 —uc .....nll I■ww ....d..• ti ..i..) u l... Com.. r J%t. _ PLACEMENT DETAILS (CONTINUED) Cm cowry. only. ►..p .w r1M.s.M..Nt 4 up 1.......upWr. *mho wow. .Mwl.. 1. 1•0141.4.6 17.22 *wore I...... M ...I.N suites Ow Placement Detail #3: Double Roll Profile Page 13of15 Product Control No.: 9$- 0303.02 fuousle Frank Zuloaga, RRC Roofing Product Control Examiner Apr- POLYFOAM PRODUCTS, INC. w.11 ft...A 06.11 .....I Wm. noirlarad by e.N) PLACEMENT DETAILS (CONTINUED) Product Control No.: 98- 0303.02 .cAAm t743 .r. In.1.« Ise e..a..l .MA /M 41.. 1.M1ry...M \ /utM a.Cl l000 Cowes l... ..r.. «dr. %..w h..n ww.'.+•a Placement Detail #4: Flat Profile Page 14 of 15 ZIloaga. I&RC Roofing Product Control Examiner MIAMI SHORES VILLAGE BUILDING INSPECTION DEPARTMENT. APPLICATION FOR BUILDING PERMIT Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the build - ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami Shores Village, Florida. and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and regulations of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved plans and specifications must be kept at building during progress of the work. Date..._..._ Friday 15 t h 88 Owner's Name and Address Mrs Barber ` _ _. ._. No 335 N . E : Street 101 Registered Architect and /or Engineer ,.,.. . ?TV t ,rttItITT <...- ..•.,a,..,_- ...... Name and address of licensed contractor Loca ,gynd I gal diescripk ,l,•2. n of lot to be bujJ tro�t v� Q Q I Lot if Block v �r f Subdivision. L/...�.GP�.l...l...g� ._— ��_. Y.SP .0 5 ;`" 1 / Street and Number where work is to be done 33 N.E. 101st Street Miami Shores , F L State work to be done and purpose of building (by floors) Re–roof carport only with a new 4-p l.y built–up gravel roof.Remove present roof.down to woodsheathing.Replace all STATE OF FLORIDA, COUNTY OF DADE. ss. Pan Am Roofing co. Inc , 1.3.61D1 W .,..Miami ,F , rot Wood.Tin cap one 43# e l t .Apply 2 / 151 b . &grave a for no other purpose. Repairs No. of Stories New Building Remodeling To be constructed of Kind of foundation Roof Covering ._ Estimated Total cost of improvements $ 1,600.00 Amount of Permit d ` 0 2 Zone cubage required plan Cubage Distance to next nearest building Size of Building Lot Maximum live load to be borne by each floor I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may be sent to.. ... Pan Am Roofing Co.Inc. 1360 N W. 29th St.Miami,FL 33142 ............. . The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer of tabor under theFlorida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement, and has complied with the provisions thereof, and will require similar compliance from all contractors or sub - contractors employed by him in the work to be performed under this permit; and will post or cause to be posted for inspection on the site of the work such public notice or notices as are required by the Act. The undersigned agrees to employ only such subcontractors, on work to be performed under this pennit, as are licensed by Miami Shores Village. Disapproved �'�i�a_. Sate (Signed) Building Inspector Remarks... (Signed)._ Ruben Bernal /ay Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap- peared • to me well known, and who, being by me first duly sworn, upon oath deposes and says that he is the. of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts therein by him stated are true. Permit No.._.et < k. Date L 1.f / .ri2.._._._ Read, Sworn to and Subscribed before me. Notary Public, State of Florida My Commission Expires PLANNING BOARD DATE Chairman Member Member Member Member ...... _.._._..._._..._. —.__ -_ Member - -- ---_ -- Council Approved. Date Disapproved Date NOTE: A charge of S1.00 will be made for making corrections or changes to this application after approval has been obtained from the Planning hoard. A re-inspection fee of 51.00 will be charged when such re- inspection is made necessary by improper notice for inspection or faulty materials and/or workmanship. Application is hereby mode for the approval of the detailed statement of the plans and specifications herewith submitted for the build - ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami Shores Village, Florida, and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and regulations of the iuilding Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved plans and specifications must be kept at building during progress of the work. H 5VIL Date..._- .._September 14th 03 Owner's Name and Address Mr $f Ivi ...._x:bAI" .-. -_._... _. No.._ U5 N.E. S 101st Street g Registered Architect and /or ynginver un.. .r19,•,! ",!,+•cr.•• rne•+•n: nm- x Name and address of licensed contactor P ?XI- 110__. ing...Co,,.Inc., 511.. 5,3i.... 3i d..Ave..14iami,_..F1..33130..._.. Location and legal description of lot to be built on: Lot Block Subdivision 335 N.E. 101st Street Miami Shores Street and Number where work is to be done State work to be done and purpose of building (by floors) Tile Roofing.- �Q�RYe _- ,xgg „�AO,...�ie�lace._a11_ rotted wood. Tin cap one 43# saturated felt_, apply Qne 94#}. .minerel-__salr.Iace4 and__install new flat white tiles in a bed__Q_fmortar,- (27 squares and for no other purpose. New Building Remodeling Addition Repairs No. of Stories To be constructed of Kind of foundation y /'R�oof Covering Til — Estimated Total cost of improvements $ 5,995.00 Amount of Permit $�.,ES►E� Zone cubage required __.____plan Cubage Distance to next nearest building Size of Building Lot Maximum live load to be borne by each floor I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may be sent to Fan - _Am.. Roofing-- .Coo.._Inc. __511_ 3r-d...Av.enue Miami,._F1- - 331 .... ........._ - -.. The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer of labor under theFlorida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement, and has complied with the provisions thereof, and will require similar compliance from all contr ctors or sub - contractors employed by him in the work to be performed under this permit; and will post or cause to be posted for ins ection • the site of a work such public ng ace or notices as are required by the Act. The undersigned agrees to employ only such su• •'fir on work t performed ender pennit, as are licensed by Miami Shores Village. Remarks __ _ _ (Signed) STATE OF FLORIDA, COUNTY OF DADE. j Ss' Before me, the undersi ned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap- peared .--ll_ 6-1R0 At_ Building Inspector Chairman \fcrnbcr Member ...... _- MIAMI SHORES VILLAGE BUILDING INSPECTION DEPARTMENT APPLICATION FOR BUILDING PERMIT and who, being by me first duly sworn, upon oath deposes and says that he is the. e-/N- 4C of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts therein by him stated are true. Permit No.___._ . e -._. __ Read w to a S ri fore me. Member Member Member // 3 o /47 BBr Contractor) to me well known, Dis Council Approved Date Disapproved Date NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval has been obtained4rotn the Planning Board. A re-inspection fee of 31.00 will be charged when such re- inspection is made necessary by improper notice for inspection or faulty materials and /or workmanship. BUILDING INSPECTION DEPARTMENT APPLICATION FOR BUILDING PERMIT Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the build- ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami Shores Village, Florida. and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and regulations of the iuilding Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved plans and specifications must be kept at building during progress of the work. Date..._ -- ... _. ,1f:74-- Owner's Name and Address .....11rs.... arber lo At Str @Pt._ No ..... Street._.. Registered Architect and /or Engineer Name and address of licensed contractor LaI>g...BQo 'iJ ..si4 Tile QO Inc,,,,_,.,. Location and legal description of lot to be built on: Lot Block Subdivision Street and Number where work is to be done 335 .__ 101at...ttreet State work to be done and purpose of building (by floors) -. -RQO :_Qne...gravel...seGtiLUlt_.. ti ._cap..J.m ....felt,_..__ 2m1ayers--- af--- 15...felt.. Cover. -- w.th- •a.-- 1aya..af... pea.. gravel, -. embedded ..intra...hat..asphalt. - ..._ and for no other purpose. New Building Remodeling Addition Repairs ,X' No. of Stories To be constructed of Kind of foundation Roof Covering Estimated Total cost of improvements $...985..Q0 Amount of Permit $.._.. Zone cubage required _Plan Cubage ,SQC }� oll__t:QnSlstj ll�..Qf ..1Q .sQuareS.... Distance to next nearest building Size of Building Lot Maximum live load to be borne by each floor I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may be sent to The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer of labor under the 'Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement. and has complied with the provisions thereof, and will require similar compliance from all contractors or ntractors employed by him in the work to be performed under this permit; and will post or cause to be posted for inspection on t site • the work such public notice or notices as are required by the Act. The undersigned agrees to employ only such subcon• s, wor be perfo d under this permit, as are licensed by Miami Shores Village. �> Remarks..._ (Signed) STATE OF FLORIDA, COUNTY OF DADE. ss. Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap- peared and who, being by me first duly sworn, upon oath deposes and says that he is the. of the above described construction, that he has carefully read e foregoing application, and that he did sign the same, and that all facts therein by him tjug, s e are Permit No Date Disapproved . (Signed) MIAMI SHORES VILLAGE Building Inspector Chairman Member Member ...... _....._..._._ ...._....... PLANNING B • RD DATE t.t. ..t... }t!SS•••'Tl.. •S>Stli!t �!} Read to and Subscribed before me. Member Member Member to me well known, otary Public, State of Florida ommission Expires Council Approved. Date Disapproved Date NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval has been obtained fmm the Planning Board. A re- inspection fee of $1.00 will be charged when such re- inspection is made necessary by improper notice for inspection or faulty materials and /or workmanship. N 1 P MIAMI SHORES VILLAGE BUILDING INSPECTION DEPARTMENT APPLICATION FOR BUILDING PERMIT Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the build- ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami Shores Village, Florida, and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and regulations of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved plans and specifications must be kept at building during progress of the work. Date...274 . J... , 19. Owner's Name and Address No � Street ' ` / O / Registered Architect and /or Engineer Name and address of licensed contractor Location and legal description of lot to be built on: Lot Block Subdivision Street and Number where work is to be done .3 !.S State work to be done and purpose of building (by floors) 7, and for no other purpose. New Building Remodeling Addition Repairs gf�Stori To be constructed of Kind of foundation R•v. 1. Estimated Total cost of improvements $._ O • 0-11 Amount of Permit $ ) . 0-1 y -4T".4.- Zone cubage required _Plan Cubage Distance to next nearest building Size of Building Lot Maximum live load to be borne by each floor I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may be sent to The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer of labor under the Florida Workmen's Compensation Act, being Section 5988, Compiled General Laws of Florida, Permanent implement. and has complied with the provisions thereof, and will require similar compliance from all contracto or sub- contractors em y ed by him in the work to be performed under this permit; and will post or cause to be posted for inspectio on e . e of the work sue f ublic notice or notices as are required by the Act. The undersigned agrees to employ only such su . antra ; rs, • '. J to be perfo under this permit, as are licensed by Miami Shores Village. Remarks . ..............._..__ (Signed STATE OF FLORIDA, COUNTY OF DADE. f ss • Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap- peared to me well known, and who, being by me first duly sworn, upon oath deposes and says that he is the. of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts therein by him stated are true. Permit No. ¢ Date 1/-/ V : . . a a.. ? Read, Sworn to and Subscribed before me. Disapproved ... te.___.__...__....._. (Signed) ._- -- --.... Notary Public, State of Florida :tot) �. <�- o��,=.'�°� Building Inspector �' �" ■ My Commission Expires PLANNING BOARD DATE Chairman Member Member ..._ Member .... Member Member ._ Council Approved _ Date Disapproved .._ Dab NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval has been obtained r the Planning Board. A re- inspection fee of $1.00 will be charged when such re- inspection is made necessary by improper notice for inspectioe materials and /or workmanship. MIAMI SHORES VILLAGE, FLA. JOB ADDRESS INSPECTION TIME READY REMARKS ' 1 i N2 5931 7/Pie, - �� aert 146"€ INSPECTOR O ���a . DATE fi- Village of Miami Shores JOB N? 4873 ADDRESS z , INSPECTION 7 6. TIME READY ,S - REMARKS INSPECTOR DATE c.'" MIAMI HORES VILLAGE, FLA. N9 5294 JOB l /I S� f ADDRESS 3 3 At 1 /0 d INSPECTION 7 ' TIME READY X47/ ® / REMARKS • INSPECTOR DATE BUILDING ELECTRICAL PLUMBING ROOFING Owner of Building �� ' MIAMI SHORES VILLAGE. FLORIDA o PERMIT N9 4619 CONTRACTOR OR BUILDER • ) ci 1 Architect Contractor or Builder j Legal Lot Description Address of Building u Work to be performed under this Permit Signed. f:• l Subdi- vision Value of Project $ x c DATE Contractor's License No L v • 1, / 195 G Amount of Permit $ This permit is granted to the contractor or builder named above to construct the building or to install the equipment or device described in the application herefor in strict compliance with all ordinances pertaining thereto and with the understanding that the work will be performed in compliance with any plans, drawings, statements or specifications that may have been submitted to and approved by the proper municipal authorities. This Permit may be revoked at any time if the work is not done in compliance with such ordinances or if the plans are changed without authorization. A further condition upon which this permit is granted is the understanding that the contractor or builder named above assumes the responsibility for a thorough knowledge of the ordinances and regulations pertaining to the work covered hereby whether shown on the plans or drawings or in the statements or specifications and that he assumes responsibility for work done by his agents, servants or employees. ` // INSPECTOR /. In consideration of the issuance to me of this permit I agree to perform the work covered hereunde in compliance with all ordinances and regulations pertaining thereto and in strict conformity with the plans, drawings, statemen or specifications submitted to e proper authorities of Miami Shores Village. In ac- cepting this permit I assume responsibility for all work done by ely er, myylf, my agent, servant or empl yee. !! BY 0 tf G/1 i AUTHORITY