1110 NE 100 St (6)12. Flashings shall be installed according to the manufacturers standard details, and may
be applied in cold application adhesive, hot asphalt or may be an approved torch
applied modified bitumen membrane. Specific details, approved by the
manufacturer, shall be submitted with the Section 11 Permit Application.
13. GAF roll good materials shall be stored on end and on a clean, flat and dry surface.
14. Consult current Underwriters Laboratories' Directory for the required coating for
each roofing assembly. The assembly shall 'be installed in strict compliance with
Chapter 3401.5 and 3401.6 of the South Florida Building Code for maximum fire
classi fication.
15...0 Asphalt moppings shall be with asphalt approved by the applicant and shall be
approved in compliance with equiviscious 'temperature (EVT) methods of asphalt
determination. Asphalt containers or bulk tickets shall indicate a EVT, finished
blowing temperature (FBT) and flash point.. Asphalt types and temperature ranges
shall be in compliance with Subsection 3403.4(a)(3) of the South Florida Building
Code. • •
16. Insulation may be installed .in.multiple. :layers. •First layer shall be attached in
compliance with Product :Control :Approval guidelines. All other layers shall be
adhered in a full mopping of approved asphalt at an application rate of 25 lbs/sq. t
15% or mechanically attached using the fastening pattern of the top layer. Refer to
manufacturer's literature and /or the NRCA'Roofing'and Waterproofing Manual for
correct application procedures of insulation panels: in hot asphalt or adhesive.
17. Pre - assembled cap nails may only be used for termination of fully bonded surfaces
such as mechanical termination at wood blocking, head and side laps, and base
flashing terminations. Cap nails shall not be used for the mechanical attachment of a
base sheet. Tin caps are required by the South Florida Building Code. •
18. The submission of system specifications and details shall accompany the Section 11
Building Code Permit. This information is available in the publications listed in the
'System Description' of this Product Control Approval. The submission of these
documents, as well as the proper application and installation of all materials shall be
the sole responsibility of the contractor.' '•
19. All standard panel sizes are acceptable for mechanical attachment. When applied in
hot asphalt, panel size shall be 4' x 4' maximum.
Gil Diamond, P.E.
75
Product Control No.: 94- 1014.01
7 /i / . //
NOTICE OF ACCEPTANCE: STANDARD CONDITIONS
1. Extensions of Acceptance may be considered after a new, application has been filed and the supporting
data, test reports no older than ten (1'0) years, have been re- evaluated.
All reports of re- testing shall bear the seal, signature and date of an engineer registered in the State of
Florida.
2. ArW revision or change in the material ,use, or manufacture of the product or process shall automatically
be cause for termination, unless prior approval is granted for revisions or change.
3. Any unsatisfactory performance of this product or process or a change in Code provisions shall be grounds
for re- evaluation.
4. This acceptance shall not be used as an endorsement of any product for sales or advertising purposes.
5. The Notice of Acceptance number preceded by the words Dade County, Florida, and followed by the .
expiration date may be displayed in advertising literature. If any portion of the Notice of Acceptance is
displayed, then it shall be done in its entirety.
e.
6. Product approval drawings, where required for permit applications, shall be provided to the applicant by
the manufacturer or his distributors unless otherwise noted in the Notice of Acceptance. The prints need
not be re- scaled by an engineer. r "t'
7. Failure to comply with the Standard Conditions shall be cause for termination of the Approval.
•t,
This approval supercedes all previous approvals.
•
Gil. am. nd•.P.E....:
Product Control Division
Supervisor•
GAFGLAS® Specifications N- B- 4 -M /P6 and N -B -4=M
Specifications
General
Application recommendations detailed on pages 17 -20 shall -apply In addition to :
the following recommendations and specifications.
Application of Rooting Membrane
1. Over entire surface, lay one ply of sheathing paper where applicable. Lap
each sheet 2 inches over preceding sheet. Nail sufficiently to hold In place. '
2. Starting at the low point of the roof, lay one ply of GAFGLAS Base Sheet, '
tapping g eacn sneer 2 unnes at edges and not Ids Clem 6 bans at eyed Ws.
Nail along lap of base ply at Intervals not to exceed 9 Inches and stagger -nail
down center of sheet in two rows with nails spaced at 18 Inch Intervals In each
row. Use fasteners with Integral metal heads at least 1 inch In diameter or .
square that are recommended by GAF Materials Corporation or the deck r' "•
manufacturer. (See'Spesial Instructions' below.)
3. Starting at the low point of the roof, mop two plies of GAFGLAS Ply shingle ':'•
fashion; lapping each sheet 19 inches over the preceding sheet; solidly mopping' -- •
to the underlying base sheet to provide three plies over the entire roof area.. : �'?
Asphalt Requirements • • '4.t `t:$I ` 4,ek
Interply moppings of Roofing Asphalt must be applied In a continuous film and •'•l
shall consist of approximately 25 pounds per 100 square feet of roof area with a'is•
tolerance not to exceed 20% plus or minus. The appropriate asphalt for the'
slopes involved must be used •' " ` `
Slope per fool
phall Typ
r As a air
L SteeP , ZP4 l :
IlT -Steep ASTNt YPJ, I• '
On slopes up to Y2 inch per foot, Flat ASTM Type 11 may be used except In ,e,' A
Florida, Texas, New Mexico, Arizona, and California.
Surfacing ,
Apply GAFGLAS Mineral Surfaced Cap Sheet in accordance with the application! yk '
instructions on page 20, so that the laps are offset from the laps of the ply sheets:
Special Instructions
1. See recommendations for use over gypsum decks on page 9. " ' s j •
2. Acceptable GAFGLAS Base Sheets include: STRATAVENP (Vent Ply) for; j ` .
Nailable Decks required for freshly poured gypsum decks, GAFGLAS #75 Base .,
Sheet, GAFGLAS PLY 6 and GAFGLAS Ply 4. For wood decks and structura►'r"
wood fiber decks, when GAFGLAS Ply 4 or GAFGLAS PLY 6 is used as a base
sheet, a sheathing paper is required.
3. See 'Nailing of Base Sheet; pages 18 -19. .. ` . • .. ` ' =': i •
4. For roof slopes of 1 Inch per foot or more, at ply felts must be back - nailed 4 Inch-
es in from the back edge of the felt. See 'Installation on Steep Roofs; page 10. , ';:. 4 ' 1
UL Classification
UL Chart Key
1. Substrate
C = Combustible and Noncombustible .
Combustible = Wood planks, boards, etc., plywood (min. 's/32 Inch thickness),
oriented strand board (min.'/ :Inch thickness).
NC = Noncombustible only i ' •
Noncombustible = Steel, poured or precast structural concrete, lightweight;
insulating concrete, gypsum, structural wood fiber, etc.
2. Slope ' `-
Maximum slope allowed, in inches per foot. ' _ . •
'•.North; South, and West
r..
Nailable decks up to 6 Inches per foot slope, except for lightweight insulating
concrete decks which are limited to a maximum slope of 1" per foot. Wood,
plywood, poured gypsum, precast gypsum planks, other acceptable nailable
decks. For lightweight Insulating concrete decks, see page 9.
ti•
0'
ppre
OAF M 1EW4d
CORPORATION
r . -
GAFGLAS
Mineral Surfaced
Cap Sheet
NNtable Deck
i1
Sheathing
required)
,. -
raid? La
r !. L .' ! , ', A NI8 ,y t9 Fy r � � ( 8 � 1 � $ r ;�'�rA�,"`'l�•' ,��.��ri�.�s � a `` �hCt n : t
iYe"e�'1�a�.12�. �/� 1...att ....I.w.IT Yt. "t e�. 4 . .�.. ?� ,� 3 Y'v:, .. •.
I, ,
! " .,,fir, cl`.� .:•.,,�
Guarantees Available
0, Specittcation , '„ 7 7,r h ? '!A! P;1 t: Liberty Guarantees
;1 yr, West Zone only Wood Decks.
15 yr. t.1 r: `.:.:.. Y: >' ' '
Llghtwelght,Insulating Concrete.
.L . , (See page 9) ` ,`1 :;.
2 +10,'10, 5 +5, 5 yl:
41
Owner's Name and Address. "Pe •
Disapproved Date
(Signed)
MIAMI SHORES VILLAGE
BUILDING INSPECTION DEPARTMENT
E.E o✓ T
APPLICATION FOR BUILDING PERMIT
Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the build-
ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami
Shores Village, Florida, and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and
regulations of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved
plans:and specifications must be kept at building during progress of the work.
Date , 19 `�
No.___.I /O Street__...ld /E X00 $ •
Registered Architect and /or Engineer ,� �1
Name and address of licensed contractor.._ 14 77) / i 4 • In r e-tj . 73 Z Oi/6 J *�Q
Location and legal description of lot to be built on:
Lot Block Subdivision
Street and Number where work is to be done ) .0 0 A & ! 0 O 4*
State work to be doe S and purpose of building (by floors)
Z4 e
and for no other purpose.
New Building Remodeling Addition Repairs No. of Stories
To be constructed of_.___C,.q . Kind of foundation Roof Covering 7 / , if ,
Estimated Total cost of improvements $ Sk.0_R2 • 0 Z. Amount of Permit $ e+
Zone cubage required Plan Cubage
Distance to next nearest building. Size of Building Lot
Maximum live load to be borne by each floor
I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may
be sent to -
The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer
of labor under the Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement,
and has complied with the provisions thereof, and will require similar compliance from all contractors or sub - contractors employed by him
in the work to be performed under this permit; and will post or cause to be posted for inspection o, e site of the work such public notice
or notices as are required by the Act. The undersigned agrees to employ only such subcontracto, .n work to be performed under this
permit, as are licensed by Miami Shores Village.
Remarks (Signed)
STATE OF FLORIDA,
COUNTY OF DADE. ss.
Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap-
peared
to me well known,
and who, being by me first duly sworn, upon oath deposes and says that he is the.
of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts
therein by him stated are true.
Permit No b Q Date ( ' — Read, Sworn to and Subscribed before me.
Notary Public, State of Florida
Building Inspector My Commission Expires
PLANNING BOARD DATE
Chairman Member
Member Member
Member Member
Council Approved Date Disapproved Date
NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval has been obtained from
the Planning Board.
A re- inspection fee of $1.00 will be charged when such re- inspection is made necessary by improper notice for inspection or faulty
materials and /or workmanship.
TELEPHONE FR 9 -747B
FR 9 -6895
Building Department
Miami Shores Village
Miami Shores, Florida
Gentlemen:
DS:nb
encl.
DON SOLOMON INC.
EnEIctL CWL12ctef02
1418 S.W. FLAGLER TERRACE
MIAMI, FLORIDA
December 15, 1958
Att: Mr. Bradford, Inspector
Enclosed please find a complete list of the
sub - contractors used in connection with the home
we erected at 1110 N. E. 100 Street, Miami Shores,
Florida, as per request by Mr. Bradford.
Very truly yours,
DON SOLOMON, INC.
By
TELEPHONE FR 9 -7478
FR 9 -6895
DON SOLOMON INC.
Qeize L Loafzceefot
1418 S.W. FLAGLER TERRACE
MIAMI, FLORIDA
December 12, 1958
LIST OF SUB - CONTRACTORS USED ON JOB, 1110 N. E. 100 Street
NAME ADDRESS TELEPHONE
Carco Industries, Inc. 2155 N.W. 25 Ave. NE 3 -2631
Concreform Co. Inc. 2001 N.E. 151 St.,No. Mia WI 7 -4553
Crabtree Insulation Co. 300 N.E. 75 St. PL 4 -6617
Crawford Door Sales 4930 E. 10th Lane, Hialeah MU 8 -4513
Emmer And Company Box 747, So. Miami MO 7 -3633
Sam L. Hamilton, Inc. 3100 N.W. 17th Ave. NE 5 -4416
Hollywood Tile & Terrazzo Co. 2106 N.Dixie Hwy.,Holl. Fla. WA 3 -6546
Metro Tile Co. 2451 N.W. 77 Terrace OX 6 -0711
Rowell - Southern Flooring, Inc. 2723 N.W. 17th Ave. NE 5 -6421
Stanley Bldg. Specialties 1890 N.E. 146 St., No. Mia. WI 7 -7531
Stark Electric Company 3628 N.W. 7th St. HI 4 -1484
Sunshine Plumbing, Inc. 1551 S. W. 27th Ave. HI 3 -5907
Gordon Thomas Plasterer 14501 No. Miami Ave. MU 1 -6075
Jack Wenshaw Painter 2553 S. W. 16th Terrace HI 3 -3097
The Zack Co. 7320 N. E. 1st Place PL 8 -6721
L & M Paving Co. 8805 N. W. 27th Ave. OX 1 -5621
Vogue Industries, Inc. 721 N. W. 21st Court FR 1 -34
F. & H. Aluminum Prod. 1476 N.E. 130 Street PL 7 -8731