1165 NE 97 St (8)Street and Number where work is to be done
MIAMI SHORES VILLAGE
BUILDING INSPECTION DEPARTMENT
APPLICATION FOR BUILDING PERMIT
Application is hereby made for the approval of the detailed state:went ur ore plans and specifications herewith submitted for the build •
in or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami
Shores Village, Florida. and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all roles and
regulations of the building Divisinn of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved
plans and specifications must be kept at building during progress of the work.
Date..._..._..._._... January _..._._ ..._ .. ,19.8 2
Owner's Name and Address f ranc ionnet _ No...lJb.?_ ..... Street-1T.1 21'.;11 citrCet
Registered Architect and /or Engineer
Name and address of licensed contractor. AGI.C.. JOO .IE.0..e.I K G. .°..f. 2116g r.T.f 21 X'erra9e
Location and legal description of lot to be built on:
Lot Block Subdivision
1165 . 9Ztk1_ street
New Building Remodeling Addition
Amount of Permit $
.Plan Cubage
Size of Building Lot
State work to be done and purpose of building (by floors).ELP lace old roof on residence (flat t: 1tc
' cement tile) .... __..._. w.. ..._..._......_._..__.._- »...._
�. _ ............... for no other purpose.
Repairs No. of Stories
To be constructed of Kind of foundation Roof Covering 24 .. ,y G. uQ.?4).
Estimated Total cost of improvements $.... 7 . 5x.65 v 00
Zone cubage required
Distance .to next nearest building
Maximum live load to be borne by each floor
I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may
be sent to.. WIAC.III...TRiOOFT11?fs. . . 69... 2' a 1I.e.... 21 ...TO..'.m.. aptli m. 1or� daa.... °.
The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an c•mployer
of labor under the Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Perm:ment Sup clement,
and has complied .eith the provisions thereof, and will require similar compliance from all con a ors or sub - contractors employed by him
in the work to be performed under this permit; and will post or cause to be poste o specti non he site of the work such pubic notice
or notices as arc required by the Act. The undersigned agrees to employ only suc su• tracf•rs, o'. irk to be performed under this
permit, as are licensed by Miami Shores Village.
Remarks (Signed)
STATE OF FLORIDA,
COUNTY OF DADE. J ss.
Before me, the undersigned authority, as notary public, duly authorized to administer oaths and take acknowledgments, perso tally ap-
peared A l V 4- C- 1 Z.
to me wel.e known,
and who being by me first duly sworn, upon oath deposes and says that he is the. .4 -. /..e J.i.�..Se.b....2w? r% /Ti' 6 ey,/tL.
of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts
therein by him stated are true.. .
Permit No..—.42.542- �i2 Date /� ,� 2 - ......._._._ Read, worn to and Subscribed before me t / 7/?=2
\ Date.._........_.
r- \ Notary Public, State of Flori
( Signed) v � ,A•. \ , Commission Expires :1.3. .2....-
Building Inspector
Chairman ...
Ucrr.ber
Member
Council Approved Date
NOTE: A charge of 51.00 will be made for
the Pl.rnnir.g lloard.
A re- inspection fee of 51.00 will be charged
materials and/or workmanship.
PLANNING BOARD DATE
Member
Member
Member
Disapproved Date
making corrections or changes to this application after approval has been obtained from
when such re- inspection is made necessary by improper notice for inspection or faulty
a9 - 3 >_O. o72
L.6 3
Date
PERMIT APPLICATION FOR MIAMI SHORES VILLAGE
Job Address //6.9 9 /5-7 Tax Folio
Legal Description Historically Designated: Yes No
Owner/Lessee / Tenant 4'
Owner's Address / //. ' ' r 51
Contracting Co.
C0Lois Re # ORR:be_
Qualifier /
- o
17K.Asd,4 Master Permit # ,S -__ 7
State # Municipal # 0 3/c - 'if Competency # Ins. Co. 4' 5" /
Architect/Engineer Address
Bonding Company Address
Mortgagor Address
Permit Type (circle one): BUILDING ELECTRICAL PLUMBING MECHANICAL ROOFING PAVING FENCE SIGN
WORK DESCRIPTION
IA)
rte/t4 . /47
Square Ft Estimated Cost (value) /c
WARNING TO OWNER: YOU MUST RECORD A NOTICE OF COMMENCEMENT AND YOUR FAILURE TO DO SO MAY
RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY (IF YOU INTEND TO OBTAIN FINANCING,
CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT.)
Application is hereby made to obtain a permit to do work and installation as indicated above, and on the attached addendum (if applicable). I
certify that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that separate
permits are required for ELECTRICAL, PLUMBING, SIGNS, POOLS, ROOFING and MECHANICAL WORK.
OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable
laws regulating construction and zoning. Furthermore, I authorize the above -named contractor to do the work
9 Signature of Contractor or Owner- Builder
Signature of owner and/or Condo President Date
) re .9- 5 "?1
Notary as to Owner and/or Condo t% esident Date
My Commission Expires:
r 1VPL � :.: �_ ��c
2
FEES: PERMIT - p RADON C.C.F. A e NOTARY
APPROVED:
Zoning Building
Mechanical Plumbing
Phone
Address/ - Gee d' ✓ 7 r� ��� � '
Phone 9 V? ° `t-
Notary to Contractor or Owner -Build cr Date
My Commission Ftt�, 914044 E iozz cc41 "
Mr Com
ExPues Nov. 06,
Bonded b i'lf"
8 00.224 -6368
Electrical
TOTAL DUE ' V/ n
Engineering
Date 0.2 9) Job Address / S ..e/E 97
Legal Description �f t
Owner / Lessee / Tenant Master Permit #
Owner's Address
Contracting Co. ( 745R. 0 i " � Address 1 I
Qualifier egReit)C€ ( 1)L 0e/2 /t+ Phone 9 V 7 g - 6 0 Z'
APPROVED:
Architect /Engineer Address
Bonding Company Address
Mortgagor Address
Permit Type(circle one): BUILDING ELECTRICAL PLUMBING MECHANICAL ROOFING PAVING FENCE SIGN
PERMIT APPLICATION FOR MIAMI SHORES VILLAGE
State # Municipal # )- 3'q -3 Competency # 113 5 °- 2 Ins .Co. 6/.5
WORK DESCRIPTION c./Lt Q t - es2 � V2 a
6 5 - 190.71e. Co (f //
k ivv.) A
I1 C9 ,u, cl 57
Square Ft. Estimated Cost(value)
OWNER'S AFFIDAVIT: I
be done in compliance
authorize the above -named contractor
Signatur of owner and /or Condo President
Date: 4
My Commission y �j } J.4� T .} ' �+�i ? r€a' = T , Y
i _�1C.11L i \∎J 1AA. S.:t,! 1. A ` /+
2 N P JL[^L �u�i I,G r�i ✓l l
** 7 cotai ,CX No. c ar3?^ y* *
q MY COMMISST3N 2.X?..E1'i 20 193d f
Tax Folio
Phone % ? /
4 2. -----
WARNING TO OWNER: YOU MUST RECORD A NOTICE OF COMMENCEMENT AND YOUR FAILURE TO DO
SO MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY (IF YOU INTEND
TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR
NOTICE OF COMMENCEMENT).
Application is hereby made to obtain a permit to do work and installation as indicated above, and
on the attached addendum (if applicable). I certify that all work will be performed to meet the
standards of all laws regulating construction in this jurisdiction. I understand that separate
permits are required for ELECTRICAL, PLUMBING, SIGNS, POOLS, ROOFING and MECHANICAL WORK.
certify that all the foregoing information is accurate and that all work will
with all applicable laws regulating construction and zoning. Furthermore, I
to do the work stated.
Notary as to Owner andf ox Q • Preg dent
FEES: PERMIT :?,7 S" RADON C.C.F. NOTARY TOTAL DUE
Fire :l Other
Zoning Buildin_ fit/ Electrical
Mechanical Plumbing Engineering
*
v
Signature of Contractor or yWner- Builder
Date: j9
Nota y g � Qntr4Ctor or _Own Builder
My Commi s s i on7' ki J `'
NOTA2.Y PUB= £. t` v 3:
COii MfS313N NC. CC2C�•'!)
P1�
CO '���. 1-N� e.�,i�: i * **
dd '` . '
J �
r as _
BUILDING
ELECTRICAL
PLUMBING
ROOFING
MIAMI SHORES VILLAGE. FLORIDA
❑ PERMIT N? 6257
❑
Owner of
Building
Architect
Contractor
or Builder
Legal Lot
Description ' Bl
Address of
Building
DATE 195__ —
Contractor's
License No.
Work to be performed under this Permit
Subdi-
vision
Value of
Project $
Amount of
1 1 Permit $
This permit is granted to the contractor or builder named above to construct the building or to install the equipment or device described in the application
herefor in strict compliance with all ordinances pertaining thereto and with the understanding that the work will be performed in compliance with any Flans
drawings, statements or specifications that may have been submitted to and approved by the proper municipal authorities. This Permit may be rovcked at any
time if the work is not done in compliance with such ordinances or if the plans are changed without authorization. A further condition upon which ti is permit is
granted is the understanding that the contractor or builder named above assumes the responsibility for a thorough knowledge of the ordinances and regulc.tions
pertaining to the work covered hereby whether shown on the plans or drawings or in the statements or specifications and that he assumes responsibility for work
done by his agents, servants or employees.
Signed BY: —_—
INSPECTOR
In consideration of the issuance to me of this permit I agree to perform the work covered hereunder in compliance with all ordinances and regulctions
pertaining thereto and in strict conformity with the plans, drawings, statements or specifications submitted to the proper authorities of Miami Shores Village. In ac-
cepting this permit I assume responsibility for all work done by either, myself, my agent, servant or employee.
CONTRACTOR OR BUILDER
BY AUTHORITY
6 -,
Date 8 J o b A d d r e s s 1 ( . 0 lj N F 975'e Tax Folio // 3 a O 6-0 / 7 ® 30
Legal Description (� Historically Designated: Yes
/Lessee / Tenant �" , (A.(�lll
Master Permit #
u)
Owner's Address I 1 L 5 lr 1 '1 S
Contracting Co.O b' F P- D v- POD FL, 4 )
Qualifiers a .A , - . O fi E dJ O J
State tee, 0 l ' f 3 0(0, Municipal # Competency # 7):1 i{J'Lf Ins. Co. o M "
Architect/Engineer
Bonding Company
Mortgagor
Square Ft.
Signature of owner and/or Condo President
• ERMIT APPLICATION FOR MIAMI SHORES VILLAGE
✓t /S y G,Aor. c
O u S�
x d��
No as to Owner and/or Cond 'don Da
My Conmissio Expires; CC623733
-41 LIOND 'I4ROIjGSi
A C O D G C O .. NC.
FEES: PERMIT 60 RADON
APPROVED:
Zoning Building
Mechanical
Address
V/S
C.C.F.
SS# Phone 1 S'1 / z
Address
Address
Permit Type (circle one): BUILDING ELECTRICAL PLUMBING
WORK DESCRIPTION ( O F p / 7- 44f 4o t
Adciressg3 /. �� ( A4 (,t/ 1
MECHANICAL ' OOFING AVING FENCE SIGN
Estimated Cost (value) 2 6' 6-1d
WARNING TO OWNER: YOU MUST RECORD A NOTICE OF COMMENCEMENT AND YOUR FAILURE TO DO SO MAY
RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY (IF YOU INTEND TO OBTAIN FINANCING,
CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT.)
Application is hereby made to obtain a permit to do work and installation as indicated above, and on the attached addendum (if applicable). I
certify that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that separate
permits are required for ELECTRICAL, PLUMBING, SIGNS, POOLS, ROOFING and MECHANICAL WORK.
OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable
laws regulating construction and zoning. Furthermore, I authorize the above -named contractor to do the work stated.
ature of Contractor or Owner- Builder
Q
Notary as to Contractor or Owner - Builder
My Commission Expires:
t1 p� SANDRA D. MART
rI �� -c�, °.5d`,,ns�o {, CC62:1
�.;
f'?r.t, cs MAR 12, 2Q01
CONDro n-IROOGH
e (Xv
ATLANTIC aOND1i4G CO.. NC.
'• & D NOTARY
Phone 7S 1— ¥ S si
(it)
Electrical
ONO
Date
to
BOND 3 6
TOTAL DUE 3 CP • g
Plumbing Engineering
NOTICE OF COMMENCEMENT
A RECORDED COPY MUST BE POSTED ON THE JOB SITE AT TIME OF FIRST INSPECTION
PERMIT NO. TAX FOLIO NO. // 302 Ss D/ 7 o 0
STATE OF FLORIDA:
COUNTY OF DADE:
THE UNDERSIGNED hereby gives notice that improvements will be made to certain real property, and in accordance with
Chapter 713, Florida Statutes, the following information is provide d in this Notice of Commencement.
1. Legal description of property and street address: 11611 llle q 7 S
2. Description of improvement: f 'vr — la/ 11' 9 del
3. Owner(s) name and address: (1104 e,L1 143114
11(o5 A10 9 7.5V2
Interest in property: ` ' wiUP.4.
Name and address of fee simple titleholder:
4. Contractor's name and address:
5. Surety:(Payment bond required by owner from contractor, if any)
Name and address:
Amount of bond $
6. Lender's name and address:
ti
7. Persons within the State of Florida designated by Owner upon whom notices or other documents may be served as provided
by Section 713.13(1)(a)7., Florida Statutes,
Name and address:
8. In addition to himself, Owner designates the following person(s) to receive a copy of the Lienor's Notice as provided in
Section 713.13(1)(b), Florida Statutes.
Name and address:
9. Expiration date of this Notice of Commencement: (the expiration date is 1 year from the date of recording unles'
different date is specified)
o� i4J,LL
Signature of Owner
Print Owners Name jog ) I-. CJA L L
Sworn to and subscribed before me this it day of
-T
Notary Public s : _ � .f f e . .. % ' / 7V
Print Notary's Nam OF �P‘s i ]'
My Commission Expires:
<1 0^ CR,DA, COUNTY OF pADz
( .taPV Oho this is 0 9r / try OP 0'"
;''oci do Ohio off co ott
O bz.Ar t,c kix-ri /tQ
9 30/..s Pairk r-c
I r
,19
Prepare(
A �.
pp
. UNIFORM ROOF PERMIT endix "E" APPLICATION
PROCESS No.
Contractor's Name: D beaJo /p c. Job Address: 1 /O5 ik)g , - :
i ii;( -2, 1' 4 -j t , '' ..1
ROOF ATEGORY �' ' a
G J1 L i i . � .- 7
(Low Slope Application) ❑ (Nail -On Tile) ❑ o dhe iic t,/Tile)
❑ (Asphalt/Fiberglass Shingles) ❑ ( Metal Roofs \Wood Shingles & Shakes) ❑ )\ J J
ROOF TYPE -- L
❑ New Roof .R Re roofing ❑ Recovering ❑ Repair ❑ Maintenance
Flat Roof Area (ft') Le-0 Sloped Roof Area (ft') Total (ft') o �' Master Permit No.
Exposure category (per ASCE 7 -88): ( Building Classification category (per ASCE 7 -88 table 1): /
Rir, -,,,,/ <64-J4 .AIi 41 /.v ,I.1WEA
G /edv(L s ✓,efisttf
6 /Is5'92J 464'd, 4
6 9 tat h -�
\ 4 ,4,e 4f f ,z Y 44,:.fo
— Xo1',N
Deck type: aJ cave /J i
Fastener Type: / 1 ,104 i f-48.44
- 13x.86= 3 (01hr
ROOF HEIGHT AND SYSTEM DETAILS
(Draw details as needed)
ATTACHMENT
SPACING
fi �i It n it mi 4
Field: 9 ` (2 Perimeter: /o ' 1 Corner: 7 `
L 2
F
S
J ',
DETAIL 1 & 2
0
&
5
y
1
r
age -
3Gk� s'8y
—82- )c _ 6.5
r
r
ROOF PLAN
A e Pee attie If - s
N Beta
•
AETRO -MDE
PRODUCT CONTROL NOTICE OF ACCEPTANCE
The expense of such testing will be incurred by the manufacturer.
Acceptance No.: 97- 0804.21 Revises No.: 95- 1003.03
Expires: 11/04/00
Approved: 11/04/97
Internet mail address: postmaster @buildingcodeonline.com
1
METROPOLITAN DADE COUNTY, FLORIDA
METRO -DADE FLAGLER BUILDING
BUILDING CODE COMPLIANCE OFFICE
METRO -DADE FLAGLER BUILDING
140 WEST FLAGLER STREET, SUITE 1603
MIAMI, FLORIDA 33130 -1563
(305) 375-2901
FAX (305) 375 -2908
GAF Materials Corporation
1361 Alps Road
Wayne, NJ 07470
Your application for Product Approval of:
GAF Conventional Built -Up Roof Systems for Wood Decks
under Chapter 8 of the Metropolitan Dade County Code governing the use of Alternate Materials and Types of
Construction, and completely described in the plans, specifications and calculations as submitted by:
Dynatech Engineering, Inc., Factory Mutual Research Corporation, and Underwriters Laboratories, Inc.
has been recommended for acceptance by the Building Code Compliance Office to be used in Dade County, Florida
under the specific conditions set forth on pages 2 -40 and the standard conditions on page 41.
This approval shall not be valid after the expiration date stated below. The Building Code Compliance Office
reserves the right to secure this product or material at any time from a jobsite or manufacturer's plant for quality
control testing. If this product or material fails to perform in the approved manner, the Building Code Compliance
Office may revoke, modify, or suspend the use of such product or material immediately. The Building Code
Compliance Office reserves the right to revoke this approval, if it is determined by the Building Code Compliance
Office that this product or material fails to meet the requirements of the Building Code Compliance Office that this
product or material fails to meet the requirements of the South Florida Building Code.
aul Rodriguez
Product Control Supervisor
THIS IS THE COVERSHEET, SEE ADDITIONAL PAGES FOR SPECIFIC AND GENERAL
CONDITIONS
BUILDING CODE COMMITTEE
This application for Product Approval has been reviewed by the Metropolitan Dade County Building Code
Compliance Office and approved by the Building Code Committee to be used in Dade County, Florid under the
conditions set forth above.
PRODUCT CONTROL DIVISION
(305) 375 -2902
FAX (305) 372 -6339
Charles Danger, P.E.
Director
Building Code Compliance Dept.
Metropolitan Dade County
a?-tJ
Homepage: http : / /www.buildingcodeonline.com
Applicant:
GAF Materials Corporation
1361 Alps Road
Wayne, NJ 07470
PRODUCT CONTROL NOTICE OF ACCEPTANCE
ROOFING SYSTEM APPROVAL
Category: Membrane Roofing System
Sub - Category: Built - up Roofing
Type: Conventional
Sub -Type: Fiberglass
System Description
GAF Materials Corporation, a manufacturer of commercial roofing products for more than 100 years,
produces a wide range of roof products for built -up and modified bitumen roofing systems. In addition,
GAF offers two ply modified systems to meet the demands for multi -ply SBS modified specifications.
GAF provides warranted systems over various insulated and non - insulated substrates, copies of which
can be obtained from GAF and can be found in the "GAFGLAS Built -Up Roofing Application and
Specifications" manual published annually.
GAF roof system assemblies have been extensively tested at Factory Mutual Research Corporation and
Underwriters Laboratories and have been tested in compliance with all requirements of the South Florida
Building Code. Specific classifications for assemblies are listed in the current U.L. Roofing Material
Directory and the current Factory Mutual Approval Guide.
GAF Materials Corporation products are distributed through a wide network of roofing wholesale
distributors throughout the South Florida area.
For more information on specific roof system constructions, contact the Technical Service Office, located
in Wayne, New Jersey, at 1- 800 -ROOF -411.
Contact:
William J. Woodring
Director of Technical Services
(973) 628- 4134
Page 2 of 41
Product Control No: 97- 0804.21
Product Control No.: 97 0804.21
Approval Date: November 4, 1997
Expiration Date: November 4, 2000
Zuloaga,
Roofing Product Control Examiner
Insulation Types:
Material
Wood
Material
Wood
Basalt Wool
Perl ite
Polyisocyanurate
Composite Board
Wood Fiberboard
High Density Wood Fiberboard
Rockwool
Maximum Design Pressure
Design Pressure
-75psf
Maximum Fire Classification
Classification
Class 'A'
Note: Fire classifications and maximum design pressures do not reference all assemblies over all deck
types. Review system listings for design pressures and the Underwriters Laboratories Roofing
Materials Directory for Fire Classifications.
Page 3 of 41
Product Control No: 97- 0804.21
Roofing Product Control Examiner
Product
GAF Asphalt
Concrete Primer
GAF Mineral Shield®
Granules
GAF WeatherCoat®
Emulsion
GAF Premium
Fibered Aluminum
Roof Coating
GAF Jetblak All
Weather Plastic
Cement
RUBEROID®
Modified Bitumen
Flashing Cement
Jetblack Premium
Flashing Cement
GAFGLAS® #75
GAFGLAS #80
Ultima Base Sheet
GAFGLAS PIy 6®
GAFGLAS Flex
PIyTM 6
GAFGLAS Ply 4 ®
TRADE NAMES OF PRODUCTS MANUFACTURED OR
LABELED BY APPLICANT
Test
Dimensions Specification
Product Control No: 97- 0804.21
Product
Description
5, 55 gallons ASTM D 41 Asphalt concrete primer used to promote
adhesion of asphalt in built -up roofing.
60 Ib. bags ASTM D 1 863 Granules for surfacing .of exposed
asphalt, cold process cement or
emulsion. GAF Mineral Shield®
Granules shall be used for flashing
applications only.
5 gallons ASTM 1227 Surface coating for smooth surfaced
roofs.
1, 5 gallons ASTM D 2824 Fibered aluminum coating.
1, 5 gallons
5 gallons
3 sq. roll
75 Ib. roll
2 Sq. Roll
70 lbs. /roll
5 sq. roll
45 Ib. roll
5 sq. roll
45 Ib. roll
5 sq. roll
ASTM D 3019
ASTM D 3409
Page 4 of 41
Refined asphalt blended with a mineral
stabilizer and fibers. Permits adhesion
to wet and dry surfaces.
5 gallons ASTM D 4586 Fiber reinforced, polymer modified
Flashing cement
ASTM D 4586 Asphalt flashing Cement
ASTM D 4601 Asphalt impregnated and coated glass
mat base sheet.
ASTM D4601 Asphalt impregnated and coated,
fiberglass base sheet
ASTM D 2178 Type VI asphalt impregnated glass felt
with asphalt coating.
ASTM D 2178 Type VI asphalt impregnated glass felt
with asphalt coating.
ASTM D 2178 Type IV asphalt impregnated glass felt
with asphalt oa iu$,
0o ing Product Contro
Product Control No: 97- 0804.21
Test Product
Product Dimensions Specification Description
GAFTITE® Base PA 114 Base sheet fastening assembly.
Sheet
Fastener and Plate
Galvalume Plates 3" and 3 ''A" PA 114 Round galvalume stress plates.
NTB Fasteners PA 114 Fastener for use in gypsum, tectum and
lightweight insulating concrete decks.
Polypropylene Plates 3" and 3 ''A" PA 114 Round polypropylene stress plates.
Ruberoid® 20 1.5 sq. roll ASTM D 5147 SBS modified asphalt base sheet and
95 lbs. interply sheet reinforce with a glass fiber
mat.
Ruberoid® Mop 1 sq. roll ASTM D 5147 Non -woven polyester mat coated with
Granule 103 lbs. polymer modified asphalt and surfaced
with mineral granules.
RUBEROID MOP 1 sq. roll ASTM D 5147 Non -woven polyester mat coated with
Smooth 87 lbs. polymer modified asphalt and smooth
surfaced.
RUBEROID® MOP 1 sq. roll ASTM D 5147 Non -woven polyster mat coated with
PLUS 102 lbs. polymer modified asphalt and surfaced
with mineral granules.
RUBEROID® MOP 1 sq. roll ASTM D 5147 Non -Woven polyester mat coated with
170FR 103 lbs. fire retardant polymer modified asphalt
and surfaced with mineral granules.
RUBEROID® MOP I sq. roll ASTM D 5147 Non -Woven polyester mat coated with
FR 105 lbs. fire retardant polymer modified asphalt
and surfaced with mineral granules.
RUBEROID® 1 sq. roll ASTM D 5147 Heavy duty, polyester reinforced,
TORCH Smooth 87 lbs. asphalt modified bitumen membrane,
smooth surface.
RUBEROID® 1 sq. roll ASTM D 5147 Heavy duty, polyester reinforced,
TORCH Granule 102 lbs. asphalt modified bitumen membrane,
granule surface.
Page 7 of 41
ing Product Control Examiner
Product
RUBEROID®
TORCH PLUS
RUBEROID®
TORCH FR
RUBEROID® 30
RUBEROID® 30 FR
RUBEROID
ULTRACLAD® SBS
Vent Stacks (metal
and plastic)
GAF Aluminum
Emulsion
Dimensions
% sq. roll
93 lbs.
' sq. roll
90 lbs.
1 sq. roll
92 lbs.
I sq. roll
92 lbs.
lsq. roll
101 lbs.
5 gallons
RUBEROID® 109. Roll
ULTRACLAD® SBS 101 lbs.
GAF Aluminum Roof 5 gallons
Paint
GAF Built -Up 100 Ib. cartons,
Roofing Asphalt bulk
RUBEROID MOD 60 Ib. kegs
Asphalt
Test
Specification
ASTM D 5147
ASTM D 5147
ASTM D 5147
ASTM D 5147
ASTM D 5147
PA I00(A)
ASTM D 1929
ASTM D 635
None
ASTM D 5147
ASTM D2824,
Type I
ASTM D312,
Types 1, 11, III and
1V
Page 8 of 41
Product Control No: 97- 0804.21
Product
Description
Heavy duty, polyester reinforced,
asphalt modified bitumen membrane,
granule surface
Heavy duty, polyester reinforced, coated
with fire retardant asphalt modified
bitumen membrane, granule surface.
Non woven fiberglass mat coated with
polymer modified asphalt and surfaced
with mineral granules.
Non woven fiberglass mat coated with
fire retardant polymer modified asphalt
and surfaced with mineral granules.
Woven fiberglass mat coated with
Polymer modified asphalt and surfaced
with aluminum, copper or stainless steel
foil.
One way valve vent used to relieve
built -up pressure within the roof system.
GAF Vent Stacks are available in metal
or plastic.
Mineral colloidal bituminous emulsion
with reflective aluminum flakes
Woven fiberglass mat coated with
Polymer modified asphalt surfaced with
aluminum, copper or stainless steel foil.
Non - fibered. aluminum pigmented,
asphalt roof coating
lnterply mopping and surfacing asphalt
SEBS modified asphalt
Roofing Product Control Examiner
Pyrox
Product
ACFoam 1
ACFoam 11
Hy -Therm Nail -line
Hy -Therm SP
Hy -Therm AP
Hy -Therm Stable R
Hy -Therm White
Line
Anchorbond
Fastener
Dekfast Fasteners
#14
Dekfast Hex Plate
TRADE NAMES OF PRODUCTS MANUFACTURED BY OTHERS
Test
Dimensions Specification
various
various
various
various PA 110
various PA 110
various PA 110
various PA 110
various PA 110
PA 114
PA 114
2 7/8" x PA 114
3 1/4"
Product
Description
PA 110 Polyisocyanurate foam
insulation
PA 110 Polyisocyanurate foam
insulation
PA 110 Polyisocyanurate foam
insulation
Polyisocyanurate foam
insulation
Polyisocyanurate foam
insulation.
Polyisocyanurate foam
insulation
Polyisocyanurate foam
insulation
Polyisocyanurate foam
insulation
insulation fastening
assembly
Insulation fastener for steel
and concrete decks
•
Galvalume hex stress plate.
Page 11 of 41
Product Control No: 97 0804.21
Manufacturer
Apache Products Co.
(with current PCA)
Atlas Energy
Products
(with current PCA)
Atlas Energy
Products
(with current PCA)
Celotex Corp.
(with current PCA)
Celotex Corp.
(with current PCA)
Celotex Corp.
(with current PCA)
Celotex Corp.
(with current PCA)
Celotex Corp.
(with current PCA)
Celotex Corp.
(with current PCA)
Construction
Fasteners Inc.
(with current PCA)
Construction
Fasteners Inc.
(with current PCA)
u oaga,
Roofing Product Control Examiner
Product
Dekfast Lock Plate 3" x 3 1/4" PA 114
Dekfast Fasteners
#14
Dekfast Fasteners
#12
ISO 95+ Composite
Asphalt
Asphalt Primer
EPS
various
High Density Wood various
Fiberboard
Pelite /Urethane
Composite
Perlite Insulation
Polyethylene
Red Rosin
Roofing Nails
Test
Dimensions Specification
various
various
4 mil min.
various
Minimum #
12
PA 114
PA 110
PA 110
PA 110
PA 110
PA 110
PA 114
Product
Description
Polypropylene locking
plate.
Insulation fasteners for
concrete decks
ASTM D 312 Type 111 or IV Hot asphlat
bitumin adhesive
ASTM D 41 Asphalt Primer
Extruded polystyrene
insulation
Wood fiber insulation board
Perlite / urethane composite
board insulation
Perlite insulation board
Vapor barrier / Air barrier
kosin paper for barrier
layer on wood decks
Corrosion resistant annular
ring shank nails
Page 12 of 41
Product Control No: 97 0804.21
Manufacturer
Construction
Fasteners Inc.
(with current PCA)
Construction
Fasteners Inc.
(with current PCA)
PA 114 Insulation fastener for steel Construction
and wood decks. Fasteners Inc.
(with current PCA)
Polyisocyanurate / perl ite Firestone
ridged insulation (with current PCA)
generic
generic
generic
generic
generic
generic
generic
generic
generic
Roofing Product Control Examiner
Tin Caps
Product
MB aluminum roof
coating
Dens -Deck
#12 Roofgrip
#I4 Roofgrip
Gripdek Fastener
Hexcel Fastener
Hextra
Standard Plastic
Plate
ISO 95+
E'N RG' Y -2
ISORoc
Test Product
Dimensions Specification Description
Min. 32 ga. x
I Vs"
various
3" round
various
various
various
Olympic Standard 3" round
PA 114
PA 114
PA 110
Corrosion resistant circular
discs.
PA 121 Aluminum roof coating
PA 110 Gypsum insulation board.
PA 114 Insulation fastener for steel
or wood decks
PA 114 Insulation fastener steel,
wood or concrete decks
PA 114 Insulation fastener
PA 114 Insulation fastener
Insulation fastener and
metal or plastic plate
Polyolefin plastic plate
PA 110 Polyisocyanurate foam
insulation
PA 110 Polyisocyanurate foam
insulation
Polyisocyanurate foam /
fockwool composite
insulation
PA 114 3" round galvalume
AZ55 steel plate
Page 13 of 41
Product Control No: 97- 0804.21
Manufacturer
generic
Grundy Industries
(with current PCA)
Georgia Pacific
(with current PCA)
ITW Buildex
(with current PCA)
ITW Buildex
(with current PCA)
ITW Buildex
(with current PCA)
ITW Buildex
(with current PCA)
ITW Buildex
(with current PCA)
ITW Buildex
(with current PCA)
Firestone
(with current PCA)
NRG Barriers, Inc.
(with current PCA)
NRG Barriers, Inc.
(with current PCA)
Olympic
Manufacturing
Group, Inc.
(with current PCA)
Roofing Product Control Examiner
Deck Type 1: Wood, Non - insulated New Construction or Reroof
Deck Description: 19 / )2 " or greater plywood or wood plank decks
System Type A(2): Base sheet mechanically fastened.
All General and System Limitations shall apply.
Base Sheet:
GAFGLAS® #75, GAFGLAS #80 Ultima Base Sheet, GAFGLAS® PLY 4 ®,
GAFGLAS® PLY 6 6, GAFGLAS FlexPly, GAFGLAS® STRATAVENT®
Nailable, RUBEROID Modified Base Sheet or RUBEROID® 20 applied to the
deck with approved annular ring shank nails and minimum 1 s / tin caps at a
fastener spacing of 9" o.c. at the lap, 12" o.c. in two rows staggered along the
center line of the sheet in the field.
Ply Sheet: Two or three plies of GAFGLAS® PLY 4 ®, GAFGLAS FlexPly 6 or
GAFGLAS® PLY 60 ply sheet adhered in a full mopping of approved asphalt
applied within the EVT range and at a rate of 20 -40 lbs. /sq..
Cap Sheet: (Optional) One ply of GAFGLAS® Mineral Surfaced Cap Sheet adhered in a full
mopping of approved asphalt applied within the EVT range and at a rate of 20 -40
lbs. /sq..
Surfacing: (Required if no cap sheet is used) Install one of the following:
I.GAF WEATHER COAT® Emulsion with an application rate of 3 gal. /sq.; or
GAF Premium Fibered Aluminum Roof Coating with an application rate of 1.5
gal. /sq..
2. Asphalt flood coat at an application rate of 60 lbs. /sq. ± 20 %; plus gravel or
slag with an application rate of 400 lbs. /sq. & 300 lbs. /sq., respectively.
Maximum Design
Pressure: -45 psf. (See General Limitation #7)
Maximum Fire
Classification: 'A'. See General Limitation #2.
Maximum Slope: 6 ":12 "; See General Limitation #3.
Product Control No: 97- 0804.21
Specification No.: N- B -3 -G, N- B -3 -C, N- B -3 -M, N- B-4 -G, N- B- 4 -G /P6, N- B -4 -M, N- B- 4 -M /P6, N- B -4 -C,
N- B- 4 -C/P6, N- B -5 -C, N- B- 5 -C/PC, N- B -5 -G, N- B- 5 -G /P6, N- B -5 -M, N- B- 5 -M/P6
Page 21 of 41
ga,
Roofing Product Control Examiner
Wood Deck System Limitations:
1. Fastener spacing for anchor sheet attachment is based on a Minimum Characteristic Force (F')
of 95 lbf or greater as tested in compliance with Merto -Dade County Protocol PA 105. If F' as
tested is below 95 lbf, a professional engineer may submit a revised fastener spacing utilizing
the withdrawal resistance value taken from Merto -Dade County Protocol PA 105 and
calculations in compliance with Metro -Dade Roofing Application Stanadrd PA 117.
2 All standard insulation panel sizes are acceptable for mechanical attachment. When panels are
applied in hot asphalt, maximum panel size shall be 4' x 4'.
a. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') of
275 lbf. as tested in compliance with Merto-Dade County Protocol PA 105 & Roofing
Application Standard PA 117. If the fastener value, as field tested, are below 275 Ibf. insulation
attachment shall not be acceptable.
3 A slip sheet is required with Ply 4® Flex Ply' 6 and Ply 6® when used as a mechanically fastened
base or anchor sheet.
4. '/ Type X gypsum board is acceptable to be installed directly over the wood deck..
Page 37 of 41
Product Control No: 97 0804.21
oaga,
Roofing Product Control Examiner
GENERAL LIMITATIONS
Page 38 of 41
Product Control No: 97- 0804.21
I All asphalt shall comply with ASTM D 312 type III or type IV requirements, and
approved by applicant.
2 Fire ratings are determined by a combination of slope, deck type and assembly. Refer to
current Underwriters Roofing Materials Directory or other fire testing data listed in the
testing file. Fire ratings shall be in strict compliance with Sections 3401.5 and 3401.6 of
the South Florida Building Code.
3 Maximum slope range shall vary for each system; consult current Underwriters
Laboratories Roofing Materials Directory and manufacturer's specifications for
compliance with design criteria for each project.
4 An overlay and/or recovery board insulation panel is required on all applications over
closed cell foam insulations when the base sheet is fully mopped. If no recovery board is
used, install one layer of GAFGLASS STRATAVENT Perforated, laid dry.A base sheet
may be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.;
or strip mopped 8" ribbons in three rows, one at each sidelap and one down the center of
the sheet allowing a continuous area of ventilation. Encircling of the strips is not
acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation.
Asphalt application of either system shall be at a minimum rate of 12 lbs. /sq. Note:
Spot attached systems shall be limited to a maximum design pressure of -45 psf. Where
STRATAVENT Perforated is used over approved isocyanurate foam insulation, the
maximum design pressure is limited to —60psf.
5 All work shall be performed by a contractor licensed to do roofing work in Metro - Dade
County. Contractor shall be familiar with the details and specifications published by the
manufacturer, and the requirements of the SFBC.
6 The submission of system specifications and details shall accompany the Section II
Building Code Permit. This information is available in the publications listed in the
'System Description' of this Product Control Approval. The submission of these
documents, as well as the proper application and installation of all materials shall be the
sole responsibility of the contractor.
Roofing Product Control Examiner
7 Perimeter and corner areas shall comply with the enhanced uplift pressure of these areas,
as calculated in compliance with Chapter 23 of the South Florida Building Code. Fastener
densities shall be increase for both insulation and base sheet as needed calculated in compliance
with Metro -Dade County Roofing Application Standard PA 117. (When this limitation is
specifically referred within this NOA, General Limitation #20 will not be applicable.)
8 All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination
designs shall conform with Metro -Dade County Roofing Application Standard PA 111
and the wind load requirements of Chapter 23 of the South Florida Building Code.
9 Flashings shall be installed according to the manufacturers standard details, and may be
applied in cold application adhesive, approved asphalt or may be applied in conjunction
with an approved torch applied modified bitumen membrane. Specific details, approved
by the manufacturer, shall be submitted with the Section II Permit Application. All details
shall comply with the provision of the South Florida Building Code.
10 Fastener spacing for base sheet attachment is based on a Minimum Characteristic Force
(F') value as tested in compliance with Metro -Dade County Protocol PA 105. If the fastener
values as tested are below those listed in the System Limitations, a professional engineer may
submit a revised fastener spacing utilizing the withdrawal resistance value taken from a Metro -
Dade County Protocol PA 105 test report and calculations that comply with the wind load
requirements of Chapter 23 of the South Florida Building Code and Roofing Application Standard
PA 117.
11 Fastener spacing for insulation attachment is based on a Minimum Characteristic Force
(F') value of 275 lbf., as tested in compliance with PA 105. if the fastener value, as field tested,
are below 275 lbf. insulation attachment shall not be acceptable.
12 Asphalt moppings shall be with applied with approved asphalt and shall be in compliance
with equiviscous temperature (EVT) methods of asphalt determination. Asphalt containers or
bulk tickets shall indicate an EVT, finished blowing temperature (FBT) and flash point. Asphalt
types and temperature ranges shall be in compliance with Subsection 3403.4(a)(3) of the South
Florida Building Code.
13 Insulation may be installed in multiple layers. The first layer shall be attached in
compliance with Product Control Approval guidelines. All other layers shall be adhered
in a full mopping of approved asphalt applied within the EVT range and at a rate of 20 -40
lbs. /sq., or mechanically attached using the fastening pattern of the top layer.' Refer to
manufacturer's literature and/or the NRCA Roofing and Waterproofing Manual for correct
application procedures of insulation panels in approved asphalt or adhesive, which shall
comply with provision of Roofing Application Standard PA 117.
Page 39 of 41
Product Control No: 97- 0804.21
Roofing Product Control xam
14 All standard panel sizes are acceptable for mechanical attachment. When applied in
approved asphalt, panel size shall be 4' x 4' maximum.
15 In re- covery/re- roofing applications, prior to the application, all existing roof surfaces used as a
bonding substrate shall be tested in compliance with Metro -Dade County Protocol PA 124 for
uplift resistance. Test pressures shall be calculated in compliance with the wind load
requirements of Chapter 23 of the South Florida Building Code to the design pressure of the roof.
16 In re- roofing applications, moisture content in an existing roof must be in compliance with
Section 3401.10(m), (n) of the South Florida Building Code.
17 Roll good materials shall be stored on end and on a clean, flat and dry surface.
18 If required, any Factory Mutual Approved vapor barrier in conjunction with proprietary or
approved adhesives may be used prior to the application of the insulation layer.
19 Consult current Underwriters Laboratories Directory for the appropriate coating for each
roofing assembly to obtain the required fire rating. The assembly shall be installed in
strict compliance with sections 3401.5 and 3401.6 of the South Florida Building Code for
maximum fire classification.
20 The maximum designed pressure limitation listed shall be applicable to all roof pressure
zones (i.e. field, perimeters, corners). No rational analysis, nor extrapolation shall be
permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended
corners, and corners). (When this limitation is specifically referred within this NOA,
General Limitation #7 will not be applicable.)
Page 40 of 41
Product Control No: 97- 0804.21
u oaga,
Roofing Product Control Examiner
Product Control No: 97- 0804.21
GAF Materials Corporation ACCEPTANCE NO.: 97 0804.21
1361 Alps Road APPROVED : November 4, 1997
Wayne, NJ 07470 EXPIRES : November 4, 2000
1
NOTICE OF ACCEPTANCE STANDARD CONDITIONS
Renewal of this Acceptance (approval) shall be considered after a renewal application has been filed and the
original submitted documentation, including test supporting data, engineering documents, are no older than
eight (8) years.
2 Any and all approved products shall be permanently labeled with the manufacturer's name, city, state, and the
following statement: "Metro -Dade County Product Control Approved ", or as specifically stated in the
specific conditions of this Acceptance.
3 Renewals of Acceptance will not be considered if:
a) There has been a change in the South Florida Building Code affecting the evaluation of this product and
the product is not in compliance with the code changes;
b) The product is no longer the same product (identical) as the one originally approved; •
c) If the Acceptance holder has not complied with all the requirements of this acceptance, including the
correct installation of the product;
d) The engineer who originally prepared, signed and sealed the required documentation initially submitted,
is no longer practicing the engineering profession.
4 Any revision or change in the materials, use, and/or manufacture of the product or process shall automatically
be cause for termination of this Acceptance, unless prior written approval has been requested (through the
filing of a revision application with appropriate fee) and granted by this office.
5 Any of the following shall also be grounds for removal of this Acceptance:
a) Unsatisfactory performance of this product or process;
b) Misuse of this Acceptance as an endorsement of any product, for sales, advertising or any other
purposes.
6 The Notice of Acceptance number preceded by the words Metro -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the Notice of Acceptance is
displayed, then it shall be done in its entirety.
7 A copy of this Acceptance as well as approved drawings and other documents, where it applies, shall be
provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site
at all times. The copies need not be resealed by the engineer.
8 Failure to comply with any section of this Acceptance 'shall be cause for termination and removal of
Acceptance.
9 This Acceptance contains pages 1 through 41
END OF THIS ACCEPTANCE
Page 41 of 41
oaga,
Roofing Product Control Examiner
75
q
1
'4
ROOF COVERING MATERIALS (TENT)
ROOFING SYSTEMS (TGFU) Continued
Foam: "Poly -Iso" or "Poly -Iso Special" with " Polyfoam 251" or "Polyfoam 3 03 ", 1 in. min.
Base Coat One or two applications "Gacoftex UB- 7050 ", applied at 1
gal/sq/application or three applications, applied 1 -1/4 gal /sq /application
(16 -32 dry mils).
Surfacing: "Gacoflex UA -65" Series (various colors), applied 1 gal/sq (12
dry mils).
30. Deck: NC
Foam: "Poly -Iso" or "Poly -Iso Special" with 2
30 ", 1 in. min. "Polyfoam 251" or " Polyfoam
Base Coat: One or two applications 'Gacoftex UB- 7050 ", applied at 1
gal/sq /application or three applications, applied 1 -1/4 gal /sq /application
(16 -32 dry mils).
Surfacing: "Gacoflex UA -60" Series (various colors), applied 1 gal/sq (15
dry mils).
31. Deck: NC
Foam: "Poly -Iso" or "Poly -Iso Special" with Incline: olyfoam 251" or " Polyfoam
303 ", 1 in. min.
Base Coat "GacoSil S- 1000 ", applied at 1 gal /sq (10 dry mils).
Surfacing: 'Gacoftex 5- 1000 ", applied at 1 gal /sq (10 dry mils).
Incline: 1
32. Deck: NC
Foam: "Polyfoam 251" or " Polyfoam 303 ", any thickness.
33. Deck: NC Surfacing: "Gacoftex lire-Shield 7007 ", 40 dry mils.
Foam: " Polyfoam 275 ", any thickness. Incline: 2 -1/2
Base Coat: "Gacoftex A- 6211 ", 1 -1/2 gal/sq (14 dry mils).
Surfacing: "Gacoftex A- 6200" series (various colors), 1 -1/2 gal /sq (14
dry mils).
GAF MATERIALS CORP
1361 ALPS RD, WAYNE NJ 07470 R1306 (N)
"RUBEROID 20" or "RUBEROID Modified Base Sheet" may be utilized as an
alternate to Type G2 base sheets in any of the following Classifications.
1/2 in. thick (min) gypsum board or 1/4 in. thick (min) Georgia - pacific
"Dens-Oeck®" overlayment board may be used in any existing noncombustible
deck Classification. When this is done, the resulting roofing system is
acceptable for use over combustible (15/32 in. min) roof decks. The joints in
deck gypsum
polystyrene is part of the roofsystem, it must be placed below the
overayment board.
ASPHALT FELT SYSTEMS WITH HOT ROOFING ASPHALT
suitable alternate
for Type G1 asphalt glass fiber ply sheet ("GAFGLAS Ply 4" or
' GAFGLAS Ply 6 ") in the Class A, B or C roof systems indicated below.
The roof deck may first be covered with a Type G2 asphalt glass mat base
sheet " GAFGLAS Stratavent (Vent -Ply) perforated" or "GAFGLAS Stratavent
(Vent -Ply) for nailable decks ". Perforated to be mopped and naitable to be
mechanically attached granule side down.
As an option Type G2 asphalt glass mat base sheet ( "GAFGLAS #75 Base Sheet"
or "GAFGLAS Stratavent (Vent -Ply) for naiable decks ") may be substituted for
G3 asphalt glass fiber ply sheet ( "GAFGLAS Ply 4" or "GAFGLAS Ply 6 ") as the
nailed base ply in the following systems.
Bottom ply or base sheet may be solid mopped, spot mopped or mechanically
fastened.
Unless otherwise indicated, all insulations may be hot mopped or mechanically
fastened.
GAFGLAS Flashing " or "Ruberoid" may be used for flashing in any of the Class
A, B or C systems listed below.
When "perlite" is referenced, this includes "GAFTEMP PERMALITE®" or any
other UL Classified perlite insulation.
Crushed stone or slag are suitable alternates for gravel in any of the Cass A,
B or C systems listed.
Structural cement fiber building units are considered suitable to be included
as a deck in the following Class A, B or C systems listed over C -15/32 or NC.
The use of gypsvm board under any of the following Class A, B or C systems
does not adversely effect the rating. The use of 1/2 in. min gypsum board is
an acceptable alternate for insulation over C -15/32 decks.
The use of polystyrene insulation board between min 3/4 in. perlite board
and deck with rosin paper (perlite /rosin paper /polystyrene /perlite) is a
suitable alternate for isocyanurate board in the following Cass A, B or C
systems.
Composite a A may substituted for any anyaisorcya Isotherm RA" einsulation and n any of the
following Classifications.
Hot roofing asphalt, for use w organic and glass felts or modified bitumen and C.
membranes.
1. Deck: C -15/32 Cass A
Incline: 3
Insulation (Optional): One or more layers perlite, wood fiber, glass
fiber, isocyanurate, urethane, perlite /isocyanurate composite, perlite/
LOOK FOR MARK
ROOF COVERING MATERIALS (TEVT) 135
ROOFING SYSTEMS (TGFU) Continued
urethane composite, wood fiber /isocyanurate composite, phenolic, any
thickness.
Ply Sheet: Three or more layers Type G1 "GAFGLAS Ply 4" or "GAFGLAS Ply
6 ", hot mopped.
Surfacing: Gravel.
2. Deck: C -15/32
Incline: 2
Insulation (Optional): One or more layers perlite, wood fiber, glass
fiber, isocyanurate, urethane, perlite /isocyanurate composite, perlite/
urethane composite, wood fiber /isocyanurate composite, phenolic, any
thickness.
Ply Sheet Three or more layers Type G1 "GAFGLAS Ply 4" or "GAFGLAS Ply
6 ".
Cap Sheet: One layer Type G3 "GAFGLAS Mineral Surfaced Cap Sheet".
Incline: 2
3. Deck: NC
Insulation (Optional): One or more layers perlite, wood fiber, glass
fiber, isocyanurate, urethane, perlite /isocyanurate composite, pertite/
urethane composite, wood fiber /isocyanurate composite, phenolic, 2 in.
max.
Pty Sheet Two or more layers Type G1 " GAFGLAS Ply 4" or "GAFGLAS Ply
6 ".
Cap Sheet: One layer Type G3 "GAFGLAS Mineral Surfaced Cap Sheet".
4. Deck: NC
Incline: 1/2
Insulation: One or two layers "Isotherm R ", 4 in. max, hot mopped.
Ply Sheet: Any UL Classified gravel surfaced Class A asphalt glass fiber
mat system.
5. Deck: C- 15/32.
1
Slip Sheet (Optional): Red rosin paper, Incline: nailed to deck.
Base Sheet One layer of Type G2 "GAFGLAS #75 Base Sheet" (may be
nailed).
Ply Sheet One or more layers of Type G1 "GAFGLAS Ply 4" or GAFGLAS Ply
6 ".
Cap Sheet: One layer of Type G -3 "GAFGLAS Mineral Surfaced Cap Sheet ".
6. Deck: NC
Base Sheet: One layer of Type G2 " GAFG #75 Base Sheet ".
Ply Sheet: One or more layers of Type GI "GAFGLAS Ply 4 "" or GAFGLAS Ply
6 ".
Cap Sheet: One layer of Type G -3 "GAFGLAS Mineral Surfaced Cap Sheet ".
7. Deck: C -15/32
Incline: 2
Insulation: One or more layers perlite, glass fiber, isocyanurate, urethane,
perlite /isocyanurate composite, perlite /urethane composite, phenolic,
1.0 in. min (offset from plywood joints 6 in.).
Base Sheet: One or more layers of Type GI, G2 or G3.
Membrane: One or more layers of "Ruberoid Torch" (smooth or granule),
"Ruberoid Torch Plus" (granule), "Ruberoid Mop" (smooth or granule) or
"Ruberoid Mop Plus" (granule).
Cap Sheet: "GAFGLAS Mineral Surfaced Cap Sheet ", hot mopped.
8. Deck: C -15/32
Incline: 2
Insulation (Optional): One or more layers perlite, wood fiber, glass
fiber, isocyanurate, urethane, perlite /isocyanurate composite, perlite
urethane composite, wood fiber /isocyanurate composite, phenolic, any
thickness.
Base Sheet: Two or more layers
Ply Sheet (Optional): One rr r
more layers of Type G1.
Membrane: One or more layers of "Ruberoid Torch" (smooth or granule),
"Ruberoid Torch Plus" (granule), "Ruberoid Mop" (smooth or granule) or
"Ruberoid Mop Plus " (granule).
Cap Sheet: "GAFGLAS Mineral Surfaced Cap Sheet ", hot mopped.
1. Deck: C -15/32 Class B
Incne: 3-1/2
Insulation (Optional): One or more layers perlite, wood fiber, glass
fiber, isocyanurate, urethane, perlite /isocyanurate composite, perlite/
urethane composite, wood fiber /isocyanurate composite, phenolic, any
thickness.
Ply Sheet: Two or more layers of Type' G1 "GAFGLAS Ply 4" or "GAFGLAS
Ply 6"
Cap Sheet: Type G3 "GAFGLAS Mineral Surfaced Cap Sheet ", hot mopped.
2. Deck: C -15/32
Insulation (Optional): One or more Layers perlite, wood fiber, glass
fiber, isocyanurate, urethane, perlite /isocyanurate composite, perlite/
urethane composite, wood fiber /isocyanurate composite, phenolic, any
thickness.
Base Sheet: Two or more layers of Type G1, G2 or G3.
Membrane: One or more layers of "Ruberoid Torch" (smooth or granule),
"Ruberoid Torch Plus" (granule), "Ruberoid Mop" (smooth or granule) or
"Ruberoid Mop Plus" (granule).
Cap Sheet "GAFGLAS Mineral Surfaced Cap Sheet", hot mopped.
1. Deck: C -15/32 Class C
Insulation (Optional): One or more ayes perlite, wood fiber, glass
fiber, isocyanurate, urethane, perlite /isocyanurate composite, perlite/
ON PRODUCT
.n\;z(J
MIAMI SHORES VI1.LAGE
BUILDING INSPECTION DEPARTMENT
APPLICATION FOR BUILDING PERMIT
Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the build-
ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami
Shores Village, Florida, and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and
regulations of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved
plans and specifications must be kept at building during progress of the work.
Owner's Name and Address. Frank Bennett
Location and legal description of lot to be built on:
Lot Block Subdivision
Date No/ember. _.I., , :9 60
No 1165 Street N. E. 97 Street
Registered Architect and /or Engineer
Name and address of licensed contractor Geiger Distributors, Inc. 1160 N. W. 72 Street
Existing
Street and Number where work is to be done 1165 N. E. 97 Street
State work to be done and purpose of building (by floors)
Installation 9f 3 Won Air Conditioner
and for no other purpose.
flew Building Remodeling Addition Repairs No. of Stories
To b2 constructed of Kind of foundation Roof Covering
Estimated Total cost of improvements $
1200,00 A mount of Permit $ $6,00
Zone cubage required .Plan Cubage
Distance to next nearest building _._ Size of Building Lot
Maximum live load to be borne by each floor
I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may
be sent to 1160 N. W. 72 Street
The undersigned applicant for this building pernit does hereby certify that he understands and accepts his obligations as an employer
of labor under the Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement,
and has complied with the rovisions thereof, and will require similar compliance from all contractors or sub - contractors employed by him
in the work to be performed under this permit; and will post or cause to be posted for inspection on the site of the work such public notice
or notices as are required by the Act. The undersigned agrees to employ only such subcontractors, on work to be performed under this
permit, as are licensed by Miami Shores Village.
Remarks (Signed)
STATE OF FLORIDA,
COUNTY OF DADE. f ss
Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap-
peared
to me well known,
and who, being by me first duly sworn, upon oath deposes and says that he is the.
of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts
therein by him stated are true.
Permit No Z Date Read, Sworn to and Subscribed before me.
Disapproved t
Notary Public, State of Florida
(Signed)�L_
Building Inspgctor My Commission Expires
PLANNING BOARD DATE
Chairman ....... .. Member
Member Member
Member ._ .... Member
Council Approved Date Disapproved Date
NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval has been obtained from
the Planning Board.
A re- inspection fee of 51.00 will be charged when such re- inspection is made necessary by improper notice for inspection or faulty
materials and /or workmanship.
Owner's Name and Address Mr. Frank Bennett
STATE OF FLORIDA,
COUNTY OF DADE. ss.
Chairman
Member
Member .... - _..._.- ... -
MIAMI SHORES VILLAGE
APPLICATIDN FOR Y- UILDING PERMIT
Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the build-
ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miamd
Shores Village, Florida. and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and
regulations of the Building Division of Miami Shores Village shall be complied with, whether herein specified or trot. A copy of approved
plans and specifications must be kept at building during progress of the work.
Disapproved ........_.... Date.. �.._.. - ..
J o (/ � i
L ,
(Signed) .l _; ..�
Building nspector
BUILDING INSPECTION DEPARTMENT
- No
Registered Architect and /or Engineer
PLADI IVINC 1DOARD DATE
Member
Member
Member
Date...g
116.11E stpeeL22th;t. -,
Name and address of licensed contactor Bohnert Rfg. & Supply Co. Inc., 3710 NW 41st. St., Mimi 33142
Location and legal description of lot to be built on:
Lot Block Subdivision — ...._._
Street and Number where work is to be done 1165 NE 97thSt. Miami Shores,, Fla.
State work to be done and purpose of building (by floors). Eaito. ff.-.$ r: a\!@ 1.... r. Q9.... S23f .4.'- oi3:-- zAx'.?er.- _ -. -.1r `4 bas
2 - #30 DC felt and gravel. New 3r! face gale. gravel stop. 634 squares
and for no other purpose.
New Building Remodeling. Addition Repairs Re - roof No. of Stories 1
To be constructed of Kind of foundation Roof Covering
Estimated Total cost of improvements $ 800 Amount of Permit $.5•
Zone cubage required . ........... __.Plan Cubage
Distance to next nearest building Size of Building Lot
ofaximum live load to be borne by each floor
I hereby submit all thg plans and specifications for said building. All notices with reference to the building and its construction may
be sent to... ?10 NW 41st. St., Miami, Fla. 33142
The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer
of labor under the Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Sup ple:nent,
and has complied with the provisions thereof, and will require similar compliance from all contractors or sub - contractors employed by him
in the work to be performed under this permit; and will post or cause to be posted for inspection on the site ,f the work such public notice
or notices as are required by the Act. The undersigned agrees to employ only such s tr ctors, on w to be performed uncle:: this
permit, as are licensed by Miami Shores Village.
Remarks -- -- (Signed)...
Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap-
peared
and who, being by me first duly sworn, upon oath deposes and says that he is the.
of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, ;nd that all facts
therein by him stated are true.
/6,,e; 2 -/ ?-(7-
Permit No..- __ Date Read, Sworn to and Subscribed before me.
to me well known,
Notary Public, State of Florida
My Commission Expires
Council Approved Date Disapproved Date
NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval hes been obtained front
the Planning Board.
A re- inspection fee of SLOG will be charged when Ruch re - inspection is made necessary by !rnprropea notice for insptstitrn oe faulty
materials anti/or workmanship.