The URL can be used to link to this page

999 NE 94 St (11)Issue Date: 12/29/2006 Owner's Name: AURELIO PEDRO MARTINEZ Permit Type: Roof Work Classification: Roof - New Job Address: 999 94 Miami Shores Village, FL Contractor(s) Phone STAR ROOFING OF ORLANDO INC (786)290 - 1908 Primary Contractor Yes Additional Information Type of Work: Re -Roof Classification: Residential Additional Info: In consideration of the issuance to me of this permit. I agree to perform the work covered hereunder in compliance with all ordinances and regulations pertaining thereto and in strict conformity with the plans, drawings, statements or specifications submitted to the proper authorities of Miami Shores Village. In accepting this permit I assume responsibility for all work done by either myself, my agent, servants, or employes. I understand that separate permits are required for ELECTRICAL, PLUMBING, MECHANICAL, WINDOWS, DOORS, ROOFING and SWIMMING POOL work. OWNERS AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. Futhermore, I authorize the above -named contractor to do the work stated. Fees Due CCF Education Surcharge Permit Fee - New Roof Scanning Fee Scanning Fee Total: Building Department File Copy Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL 33138 -0000 Phone: (305)795 -2204 Fax: (305)756 -8972 Expires: 06/27/2007 Amount $3.00 51.00 5250.00 S18.75 $12.00 $284.75 Permit Invoice Number RF - 12 - 06 - 27131 Total: Parcel #: Block: Section: Tin Cap Hot Mop Tile In Progress Up Lift Report Final Roof Permit Status: APPROVED Permit Number: RF -12 -06 -3041 Total Square Feet: 600 Total Valuation: S 5.000 00 Re•uired Inspections Amt Due S284.75 JAN 0 2ffiaD Phone: 1132060350010 Lot: PB: Amt Paid NOTICE: In addition to the requirements of this permit. there may be additional restrictions applicable to this property that may be found in the public records of this county. AND THERE MAY BE ADDITIONAL PERMITS REQUIRED FROM OTHER GOVERNMENTAL ENTITIES SUCH AS WATER MANAGEMENT DISTRICTS, STATE AGENCIES, OR FEDERAL AGENCIES. RE -ROOF FLAT DECK ONLY / 2° Passed Inspector Comments CREATED AS REINSPECTION FOR INSP- 35477. All tiles to be replaced due to flat reroof must be installed by final inspection. 1/12/07 CG. Failed Correction Needed Re- Inspection Fee ($75) No Additional Inspections can be scheduled re- inspection fee is paid. until Inspection Date: 01/18/2007 Inspector: Grande, Claudio Owner: MARTINEZ, AURELIO PEDRO Job Address: 999 94 Street NE Miami Shores Village, FL Project: <NONE> Contractor: STAR ROOFING OF ORLANDO INC Building Department Comments Wednesday, January 17, 2007 Inspection Worksheet Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL Phone: (305)795 -2204 Fax: (305)756 -8972 Block: Permit Type: Roof Inspection Type: Final Roof Work Classification: Roof - New Phone Number Parcel Number 1132060350010 Lot: Phone: (786)290 -1908 Page 1 of 1 RE -ROOF FLAT DECK ONLY Infraction Passed Comments TIN CAP SPACEING True JAM 1 1 21 Passed Inspector Comments CREATED AS REINSPECTION FOR INSP- 35473. Tin cap as shown on pictures are not in compliance with the fastener spacing for flat roofs. Remove roofing materials and retintag roof or install new30# paper on top of existing roof and tag as per approved permit and re -call tin cap inspection. 1/3/07 CG. Failed Correction Needed Re- Inspection Fee ($ No Additional Inspections can be scheduled re- inspection fee is paid . until I;i spection NO .... ..................... ..... ............................... Inspection Date: 01/10/2007 Inspector: Grande, Claudio Owner: MARTINEZ, AURELIO PEDRO Job Address: 999 94 Street NE Project: <NONE> Contractor: STAR ROOFING OF ORLANDO INC Building Department Comments Tuesday, January 9, 2007 Miami Shores Village, FL Inspection Worksheet Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL Phone: (305)795 -2204 Fax: (305)756 -8972 Block: Permit Type: Roof Inspection Type: Tin Cap Work Classification: Roof - New Phone Number Parcel Number 1132060350010 Lot: Phone: (786)290 - 1908 Page 1 of 1 RE -ROOF FLAT DECK ONLY Infractio Passed Comments TIN CAP SPACEING False JAN 0 4 2007 Passed Inspector Comments Tin cap as shown on pictures are not in compliance with the fastener spacing for flat roofs. Remove roofing materials and retintag roof or install new 30# paper on top of existing roof and tag as per approved permit and re -call tin cap inspection. 1/3/07 CG. Failed ■/ Correction Needed Re- Inspection Fee ($75) No Additional Inspections can be scheduled re- inspection fee is paid. until Inspection Worksheet Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL Phone: (305)795 -2204 Fax: (305)756 -8972 Inspection Number: I NSP- 3 5 4 73 Permit Number: RF -12 -06 -3041 Inspection Date: 01/03/2007 Inspector: Grande, Claudio Owner: MARTINEZ, AURELIO PEDRO Job Address: 999 94 Street NE Miami Shores Village, FL Project: <NONE> Contractor: STAR ROOFING OF ORLANDO INC Buildin4 Department Comments Wednesday, January 3, 2007 Block: Permit Type: Roof Inspection Type: Tin Cap Work Classification: Roof - New Phone Number Parcel Number 1132060350010 Lot: Phone: (786)290 -1908 Page 1 of 1 Receipt Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL 33138 -0000 Phone: (305)795 -2204 Fax: (305)756 -8972 Permit Number: RF - - - 3041 Invoice Number: RF - - - 27131 Applicant: AURELIO PEDRO MARTINEZ Company Name: Owner Address: 999 NE 94 ST MIAMI SHORES, FL 33138 Job Address: 999 94 Miami Shores Village, FL Date Tuesday, January 2, 2007 01/02/2007 Check Payment Type Check Number 2663 Amount $284.75 Change $0. 00 Total Payment: $284.75 Page 1 of 1 City FOLIO / PARCEL # Job Address (where the work is being done) Miami Shores Village Is Building Historically Designated YES NO Architect/Engineer's Name (if applicable) Value of Work For this Permit $ Type of Work: Describe Work: Submittal Fee $ Notary $ Scanning $ Bond $ Q�J Structural Review. $ Miami Shores Village Building Department 10050 N.E.2nd Avenue, Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 me I BUILDING Jul DEC PERMIT APPLICATION & 8 20O� FBC 2004 Permit Fee $ Permit Type (circle): Building Electrical Owner's Name (Fee Si itleholder) Owner's Address City 1 �‘ State Zip Tenant/Lessee Name ❑Alteration o 1 A- 'County Miami -Dade Zip N (Ct11 ( Phone # �31 3P) 132 Contractor's Company Name ' t— / VCC:k' Lte) Permit No. RRL - O 4 Master Permit No. Plumbing Mechanical Phone # � - J] J Phone # Contractor's Address a` L -+'1 VI l an'c. City )c\ 1 V' State Qualifier Name 3 ri p m-.{ h\ O I i ss 41 State Certificate or Registration No. CCC 132? 40 8 Certificate of Competency No. Zip Phone # Phone # Square / Linear Footage Of Work: New t pair/Replace❑ Demolition • ******** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** F * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** 2 V ✓ CCF $ cpciD 1q08 LOD CO /CC Roofing Training/Education Fee $ \ Technology Fee $ Radon $ DPBR $ Zoning $ Code Enforcement $ Double Fee $ Total Fee Now Due $ ) n -S See Reverse side 2 cV(' Bonding Company's Name (if applicable) Bonding Company's Address City State Zip Mortgage Lender's Name (if applicable) Mortgage Lender's Address City State Zip Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRICAL WORK, PLUMBING, SIGNS, WELLS, POOLS, FURNACES, BOILERS, HEATERS, TANKS and AIR CONDITIONERS, ETC OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. "WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT." Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must promise in good faith that a copy of the notice of commencement and construction lien law brochure will be delivered to the person whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site for the first inspection which occurs seven (7) days after the building permit is issued. In the absence of such posted notice, the inspection will not be approved and a reinspection fee will be charged. Signature Signature Owner or Agent Contractor The foregoing instrument was acknowledged before me this The foregoing instrument was acknowledged before me this day of , 20 _, by , day of , 20 _ , by who is personally known to me or who has produced who is personally known to me or who has produced As identification and who did take an oath. as identification and who did take an oath. NOTARY PUBLIC: NOTARY PUBLIC: Sign: Sign: Print: Print: My Commission Expires: ***************************************************************************** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** APPLICATION APPROVED BY: (Revised 02/08/06) My Commission Expires: Plans Examiner Engineer Zoning • Bonding Company's Name (if applicable) Bonding Company's Address City Vc; Mortgage Lender's Name (if applicable) Mortgage Lender's Address City State Zip Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRICAL WORK, PLUMBING, SIGNS, WELLS, POOLS, FURNACES, BOILERS, HEATERS, TANKS and AIR CONDITIONERS, ETC OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. "WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT." Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must promise in good faith that a copy of the notice of commencement and construction lien law brochure will be delivered to the person whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site for the first inspection which occurs seven (7) days after the building permit is issued. In the absence of such posted notice, the inspection will not be approved a .< reinspection fee will be charged. it Owner or Agent v v Contracto The f oing instrument was ackno ledgeed me this ( The f egoing instrument was acknowledged before me this day oil oing DID, by � , ! / �•( en . day who is personally known to me or wits produce who i • 1C • As identification and who did take an oath. . ! Y P B LIC: NOTARY P : LIC: , t. � 4 , . . STATE OF FLORIDA Sig ,R eda ...:-.:�� Print: f " • a Lulsa e p Print: y�.�v` _ _ �. (2107 0 c ,, = Cornni1` - "l0II rr . _ •2107 c'•*M,r t • cirn * L)LSU 2010 m is. My Commission Expires: n ,tai: zF 11, My Commission Expires �; `I, 17, 201 v�� l6 P �, r 6 .0T;1)Cvv C0.,1SC. .. 1'�G CO., L \ (Certificate of Competency Holder) APPLICATION APPROVED BY: Chc 1 0/1 4/03 State Zip b Cl/6;170Z m- or who has produced as identification and who did take an oath. State Certificate or Registration No ∎ / 3 " - C ertificate of Competency No. Plans Examiner Engineer Zoning BUILDING PERMIT APPLICATION FBC 2001 Permit Type (circle): Building Electrical � Plumbing Mechanical J �y; Sim le Owner's Name (Fee le Titlehold , c �IIC-11 k.'ahone # 1 Q- cam- 1-- Owner's Address City ate Zip 331 SF Tenant/Lessee Name Job Address (where the work is being done) qC LJ z P . g J' City Miami Shores Village County Miami -Dade Zip B 3) Is Building Historically Designated YES NO Contractor's Company g me`-� IL ice_Z f Q^ k. EI /o� (Jh C # 7 lQ . 0 1 cOS Contractor's Address o� Oh ie! (c_KI City lC ISC1 illm ce State Zip 4---- Qualifier ii rnier Ch ICI I SS J)2 $ Value of Work For this Permit ::30c.4 Type of Work: ❑Addi Describe Work: Miami Shores Village Building Department 10050 N.E.2nd Avenue, Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 Master Permit No. Phone # Permit No. Architect/Engineer's Name (if applicable) - / Phone # Square Footage Of Work: c O • ❑New - )repair /Replace _ ❑ Demolition Oklb * * * * * * * * * * * * * * * * * * * * * * * * * * ** F ees * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** Code Enforcement $ Structural Plan Review. $ Total Fee Now Due $ (Continued on opposite side) Submittal Fee $ Permit Fee $ CCF $ Notary $ Training /Education Fee $ Technology Fee $ Scanning $ Radon $ Bond $ NOTICE OF COMMENCEMENT 111111111111 11111 11111 11111 1111111111 11111111 A RECORDED COPY MUST BE POSTED ON THE JOB SITE AT TIME OF FIRST INSPECTION PERMIT NO. TAX FOLIO NCI ( a I ' O35C STATE OF FLORIDA: COUNTY OF MIAMI -DADE: THE UNDERSIGNED hereby gives notice that improvements will be made to certain real property, and in accordance with Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement. 1. Legal description of property and street /address: }� Q4 . 2. Description of improvement: ( l�-�O 3. Owner(s) name and address: 3•1 Interest in property: Oti.) Name and address of fee simple titleholder: 4. Contractor's name and address: 5. Surety: (Payment bond required by owner fr Name and address: Amount of bond $ 6. Lender's name and address: 7. Persons within the state of Florida designated by Owner upon whom notices or other documents may be served as provided by Section 713.13(1)(a)7., Florida Statutes, Name and address: 8. In addition to himself, Owners designates the following person(s) to receive a copy of the Lienor's Notice as provided in Section 713.13(1)(b), Florida Statutes. Name and address: 9. Expiration date of this Notice of Commencement: (the expiration date is 1 year from the date of recording unless a diffe t date is spec) zSig , fu�e`of'O:wne'r. Print Owner's Nama.J ! 1 [) nZi. Sworn to and subscribed before me thid day ofak�- Notary Pu Print Notary's Name ' NOTARY PUBLIC -STATE OF FLORIDA Aria Luisa Cepeda My commission expires: fi� ` Commission ;+t DD562107 '„` „,s” Expires: JUNE 11, 2010 LONDLI THRU ATLati IC BONDING CO., INC. 123.01 -52 PAGE 4 10/04 4 .eL-C2 PATE OF FLOCt4t?A, COURTTV OF O HEREAV CERriFV thct mis Ps a Imo CO the )(Tgina�:d �n th.s otfire on / F _ day of p4, I ra; r 20 1 C 7(Zo. f0 r os' n contractor, if any) (:FN 2006R1342.879 OR PA: 252 02 Ps 27376 (1c>s) RECORDED 12/18/2006 13:27:10 HARVEY RUVIHr CLERK OF COURT MIAMI — DADE COUNTY FLORIDA LAST PAIGE Prepared b ` -" T Addre v 51-0546 r�j11 3- Reviewer: Claudio Grande C.B.O 305- 795 -2204 Ext 1430 Miami Shores Village Building Department Permit No. .Job Name Date BUILDING CRITIQUE SHEET '10050 N.E26d Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 e6. /2A1/(4. 0-F paE-e, pa-e _2 Master Permit No. �j^� yJ t Process No. S 1 C�( Contractor's Name � ' l - • `r � �� Job Address C l e tq LA E Florida Building Cod Edttioh 23704: : : High Velocity Hurricane Zone Uniform Permit F&rf ' (..rib ,, ROOF CATEGORY Low Slope ❑ Mechanically Fastened Tile ❑ Asphaltic ❑ Metal Panel /Shingles Shingles ❑ Prescriptive BUR -RAS 150 • •• •• • • • •• • • • • • • Section A (General#o m ation : MCIEEMER DEC 1 8 2006 JJ BY: ------------- - - - - -- -r•:. • • • •• •• • • • • • • • • • • • • •• • • (•• • • • • ••• •• • • ❑ Mortar /Adhesive Set Tile ❑ Wood Shingles /Shakes ROOF TYPE ❑ New Roof 'Re- Roofing ❑ Recovering ❑ Repair ❑ Maintenance ROOF SYSTEM INFORMATION Low Slope Roof Area (SF) Steep Sloped Roof Area (SF) Total (SF) COCO Section B (Roof Plan) Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains. Include dimensions of sections n evels; clearly Identify dimensions of elevated pressure zones and location of par i ' ` 1 - Fill In Specific Roof Assembly Components and Identify Manufacturer (If a component is not used, i as "NA ") System ManufaQturer: NOA No.: —050 Design Wind Pressures, From RAS 128 or Calculations: Pax, : 2`"`" e • 4 p r . , - ; / € 2 4 t . Max. Design Pressure. rOA System: • Deck: ype tocz ) Gauge/Thickness: / Slope: ! - • /L. Anchor /Base Sheet & No. of PIy(s): Anchor /Base Sheet Fastener /Bon Insulation Base Layer. Base Insulation Size and Thickness: Base Insulation Fastener /Bonding Mat Top Insulation Layer: Florida Building Codeied f ioi 2u04 • a • *; High Velocity Hurricane Zone Unifc,r r; Perri ;Applt'ceition Foim, :, Section C (Low Sloped Roo#SYs_terni ,•• •• • • • • ••••• • • • • • •• •••• • • • • • • • • • • • • • ••F Spa cin g for A /Base Sheet Top Insulation Size and Thickness: Top Insulation Fastener /Bonding terial: Base Sheet(s) & No. of PIy(s): /A / '9 • J 17})egtas�kbr ing ( N‘o Ply Sheet(s) & No. of Ply(s): Ply Sheet Fastener /B teriat: 3 k3 Top Pl 63/y 1. , Tkoft Top PIyf ten /Bon �i�9 1y� a s Surfacing: I t/( Ekl e q (..(1 01 rJ IICkt )9 ) tl /G g Material: ._..:_.. Attach t • • O • • • ••• • • Field: • • • • . " ochLap, Rows • • • Perimete r "15c MT), 'Mows Comer: l " oc @ Lap, # Rows Field Number of Fasteners Per Insulation Board Illustrate Components Noted and Details as Applicable: Woodblocking, Gutter, Edge Termination, Stripping, Flashing, Continuous Cleat, Cant Strip, Base Flashing, Counter - Flashing, Coping, Etc. Indicate: Mean Roof Height, Parapet Height, Height of Base Flashing, Component Material, Material Thickness, Fastener Type, Fastener Spacing or Submit Manufacturers Details that Comply with RAS 111 and Chapter 16. 4( , t ` scpetnr, s \ f ✓ Perimeter Comer • FT VFT • oc oc o c Parapet Height J 2� Mean Roof Height MIA M I•DADE BUILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION NOTICE OF ACCEPTANCE (NOA) GAF Material Corporation 1361 Alps Road Wayne, NJ 07470 • • • • • • • • ... .. .. • • . • .. • • • ... • • • • • • • • • • • • • • • • • • ... • • • • • • • • ••• MIAMI -DADE COUNTY, FLORIDA . . METI O -D9QE FLAGLER BUILDING 140 V ST )ti`L1G7ER STREET, SUITE 1603 : : : MLZNiI, FLORIDA 33130 -1563 (305) FAX (305) 375 -2908 .. . . . .• •-.. .. . • • • • • .. • • • • • ... .. SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by the BCCO and accepted by the Building Code and Product Review Committee to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Division (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BORA reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Division that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: GAF Ruberoid® Modified Bitumen Roof System for Wood Decks. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA #02- 0408.10 and consists of pages 1 through 31. The submitted documentation was reviewed by Frank Zuloaga, RRC. NOA No: 03- 0501.02 Expiration Date: 11/06/08 Approval Date:10 /23/03 Page 1 of 32 ROOFING SYSTEM APPROVAL Category: Sub - Category: Deck Type: Maximum Design Pressure Fire Classification: TRADE NAMES OF PR Product GAF Asphalt Concrete Primer (Matrix 307 Primer) GAF Mineral Shield® Granules GAF WeatherCoat® Emulsion (Matrix"' Fibered 305 Emulsion) GAF Premium Fibered Aluminum Roof Coating (Matrix"' System Pro Aluminum Roof Coating Fibered 301) GAF Jetblack All Weather Plastic Cement (Matrix"' Standard Wet/Dry Roof Cement 204) GAFGLAS #75® GAFGLAS #80 U1timaT' Base Sheet GAFGLAS Flex P1yT' 6 GAFGLAS Ply 4® GAFGLAS ®Mineral Surfaced Cap Sheet GAFGLAS® STRATAVENT® Eliminator Perforated Roofing SBS /APP, Modified I i 1 1m . Wood -75 psf • • • See General Limitation #1, ODUCTS MANUFACTURED OR LABELED BY APPLICANT: Dimensions 5, 55 gallons 601b. Bags 1001b. bags 5 gallons 1, 5 gallons ASTM D 2824 Fibered aluminum coating. 1, 5 gallons 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide TABLE 1 ••• • • •• • • Test Specification ASTM D 41 ASTM D 1863 ASTM 1227 ASTM D 3019 ASTM D 3409 ASTM D 4601 ASTM D4601 ASTM D 2178 ASTM D 2178 ASTM D 3909 ASTM D3672 ASTM D 4897 ••• • • • • • • • • • • • • • • ••• • • • • • • • • • • • • • • • • • • • •• • • •• • • • • • • • • • •• b • • b • • • b • • • b • • • • • •• •. •• • • Product Description Asphalt concrete primer used to promote adhesion of asphalt in built -up roofing. Granules for surfacing of exposed asphalt, cold process cement or emulsion. GAF Mineral Shield® Granules shall be used for flashing applications only. Surface coating for smooth surfaced roofs. Refined asphalt blended with a mineral stabilizer and fibers. Permits adhesion to wet and dry surfaces. Asphalt impregnated and coated glass mat base sheet. Asphalt impregnated and coated, fiberglass base sheet Type VI asphalt impregnated glass felt with asphalt coating. Type IV asphalt impregnated glass felt with asphalt coating. Asphalt coated, glass fiber mat cap sheet surfaced with mineral granules. Fiberglass base sheet coated on both sides with asphalt. Surfaced on the bottom side with mineral granules embedded in asphaltic coating with factory perforations. NOA No: 03- 0501.02 Expiration Date: 11/06/08 Approval Date:10 /23/03 Page 2 of 32 Product GAFGLAS® Flashing GAFGLAS® STRATAVENT® Eliminator Perforated Nailable RUBEROID® SBS Heat - We1dTM Smooth RUBEROID® SBS Heat - We1dTM Granule RUBEROID® SBS Heat - We1dTM 170 FR RUBEROID® SBS Heat - WeIdTM PLUS RUBEROID® SBS Heat - Weld PLUS FR RUBEROID Modified Base Sheet RUBEROID® Modified Bitumen Adhesive RUBEROID® SBS Heat - We1dTM 25 Ruberoid® Mop Granule RUBEROID MOP Smooth RUBEROID MOP PLUS RUBEROID MOP 170FR RUBEROID MOP FR RUBEROID TORCH Smooth Dimensions various 39.37" (1 meter) Wide 1 meter (39.37 ") wide 1 meter (39.37 ") wide 1 meter (39.37 ") wide 1 meter (39.37 ") wide 1 meter (39.37 ") wide 39.37" (1 meter) Wide 5 gallons 1 meter (39.37 ") wide 39.37" (1 meter) Wide 1 sq. roll 87 lbs. 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide Test Product Specification • Descrion • •• • • _ • • Aspta cvted ;lvsfrber mat flashing . :. :.. sheer available hl three Sizes. ASTM D3672 Fiberglass base sheet coated on both ASTM D'1897 .ides with asphalt. Surfaced on the • . : • totjoen gidp Ijth mineral granules : : dmbetldtd.insphalt c coating. ASTM D -6164 &on Woven Polyester mat coated with polymer - modified asphalt and smooth surfaced. Non -Woven Polyester mat coated with polymer modified asphalt and surfaced with mineral granules. Non -Woven Polyester mat coated with fire retardant polymer modified asphalt and surfaced with mineral granules. Non -Woven Polyester mat coated with polymer modified asphalt and surfaced with mineral granules. Non -Woven Polyester mat coated with fire retardant polymer modified asphalt and surfaced with mineral granules. Premium glass fiber reinforced SBS - modified base sheet ASTM D -6164 ASTM D-6164 ASTM D-6164 ASTM D-6164 ASTM D4601, Type II, UL Type G2 BUR ASTM D 3019 Type III ASTM D -6164 ASTM D 6222 ASTM D 5147 ASTM D 6298 ASTM D 5147 ASTM D 6164 ASTM D 5147 ASTM D 6164 ASTM D 5147 ASTM D 6164 ASTM D 5147 ASTM D 6222 ASTM D 5147 • • ••• • • •• •• • • • •• • • • • • • • • • • • • ••• • • • • • • • • • ••• • • • • • Fiber reinforced, rubberized Adhesive Non -Woven Polyester mat coated with polymer - modified asphalt and smooth surfaced. Non -woven polyester mat coated with polymer modified asphalt and surfaced with mineral granules. Non -woven polyester mat coated with polymer - modified asphalt and smooth surfaced. Non -woven polyester mat coated with polymer modified asphalt and surfaced with mineral granules. Non -Woven polyester mat coated with fire retardant polymer modified asphalt and surfaced with mineral granules. Non -Woven polyester mat coated with fire retardant polymer modified asphalt and surfaced with mineral granules. Heavy duty, polyester reinforced, asphalt modified bitumen membrane, smooth surface. NOA No: 03 0501.02 Expiration Date: 11/06/08 Approval Date:10/23 /03 Page 3 of 32 Product RUBEROID TORCH Granule RUBEROID TORCH PLUS RUBEROID TORCH FR RUBEROID 170FR TORCH Ruberoid® 20 Ruberoid® 30 Ruberoid® 30 FR RUBEROID® ULTRACLAD® SBS RUBEROID® Dual FR Vent Stacks (metal and plastic) GAF Aluminum Emulsion GAF Aluminum Roof Paint (MatrixTM System Pro Aluminum Roof Coating Fibered 302) GAF Built -Up Roofing Asphalt RUBEROID MOD Asphalt, Asphalt L & Asphalt P Shingle- MateTM Underlayment Tile -Mate Modified Base Sheet Dimensions 39.37" (1 meter) Wide 39.37' (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 39.37" (1 meter) Wide 5 gallons 5 gallons 100 lb. cartons, bulk 601b. kegs 4 sq. roll 30lbs. 1.5 sq. roll Test Specie^ atioe►„ ASTM p 6272 ASTMD•5S41 ASTM D §;27 ASTM 175141 ASTM D 6222 ASTM D 5147 ASTM D 6222 ASTM D 5147 ASTM D 6163 ASTM D 5147 ASTM D 6163 ASTM D 5147 ASTM D 6298 ASTM D 5147 ASTM D 6163 ASTM D 5147 ASTMD6164 ASTM D 5147 PA 100(A) ASTM D 1929 ASTM D 635 None ASTM D2824, Type I ASTM D312, Interply mopping and surfacing asphalt Types I, ]I, III and IV ASTM D 5147 • ... • •• • • • • • • • • • • • • • ••• • ..• • • • .•• • •. • • • • • • • • • .•. Product • • Doscrption Heavy duty, pobreetereinforced, asphalt mcdt eflAtumtulneiatorane, granule surface. tleayy d .ty, volyester reinforced, asphalt cncIIii f eCl 1Sf tipen Membrane, granule curlade :' . : : heavy duty, po yester reinforced, coated with fire retardant asphalt modified bitumen membrane, granule surface. Heavy duty, polyester reinforced, coated with fire retardant asphalt modified bitumen membrane, granule. surface. SBS modified asphalt base sheet reinforce with a glass fiber mat. Non woven fiberglass mat coated with polymer modified asphalt and surfaced with mineral granules. Non woven fiberglass mat coated with fire retardant, polymer modified asphalt and surfaced with mineral granules.i Woven fiberglass mat coated with Polymer modified asphalt surfaced with aluminum, copper or stainless steel foil. Non -woven polyester and fiberglass mat coated with file retardant, polymer - modified asphalt and surfaced with mineral granules. One -way valve vent used to relieve built - up pressure within the roof system. GAF Vent Stacks are available in metal or plastic. Mineral colloidal bituminous emulsion with reflective aluminum flakes Non- fibered. Aluminum pigmented, asphalt roof coating SEBS modified asphalt Fiberglass reinforced shingle underlayment SBS modified asphalt base sheet and interply sheet reinforce with a glass fiber mat tile underlayment. NOA No: 03- 0501.02 Expiration Date: 11/06/08 Approval Date:10 /23/03 Page 4 of 32 Product Tile -Mate Modified Cap Tile -Mate Modified Cap Plus TopCoat® Surface Seal SB (Matrix 602 SB Coating) GAF WeatherCote® MB+(Matrix 715 MB Coating) TopCoat MB +(Matrix 715 MB Coating) WeatherCoten (Matrix 531 WeatherCote® Elastomeric Flashing Grade) Matrix Low VOC Matrix 101 System Pro SBS Adhesive (Ruberoid ®MB) Matrix 201 System Pro SBS Flashing (Ruberoid ®MB) Matrix 102 Select SBS Adhesive (Ruberoid ®MB) Matrix 202 Select SBS Flashing Matrix 203 Standard Plastic Cement Matrix 213 Gun Grade Plastic Cement Matrix 103 Cold Adhesive Matrix 303 Select Fibered Aluminum Matrix 304 Select Non - Fibered RUBEROID® Modified Bitumen Adhesive Dimensions 1 sq. roll 103 lbs. 1 sq. roll 102lbs. 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons 5 gallons • • • •• •• • • • • • • • • • Test Specification ASTM p 5147 • O . :•• ASTM D 5147 • • • • • • • ASTM D3019 ASTM D3019 ASTM D3019 ASTM D4586 ASTM D4586 ASTM D4586 ASTM D3019 ASTM D 2824 ASTM D2824, Type I ASTM D 3019 Type III • • • • ••• • • • • • • • • • • • • • ••• • • • • • • O O • • • • • • O • Product • • Descripfion Nort-woyep polyelter mat coated with poktvef trbdifit;d 'aspbalt and surfaced with mineral granules tile underlayment. Non -woven polyester mat coated with D ojyxpet lied ,sphalt and surfaced &iMt initihal;granuleS tile underlayment. • • • • ••• •• Surface coating for smooth surfaced and mineral surfaced roofs. Surface coating for smooth surfaced and mineral surfaced roofs. Surface coating for smooth surfaced and mineral surfaced roofs. Surface coating for smooth surfaced and mineral surfaced roofs. Surface coating for smooth surfaced and mineral surfaced roofs. Cold Applied Modified SEBS Asphalt Adhesive Cold Applied Modified SEBS Asphalt Adhesive — Flashing Grade. Cold Applied Modified SEBS Asphalt Adhesive. Cold Applied Modified SEBS Asphalt Adhesive — Flashing Grade. Standard Plastic Asphalt Roofing Cement Standard Plastic Asphalt Roofing Cement Caulk Grade. Cold Applied Asphalt Adhesive. Fibered aluminum coating. Non - fibered. Aluminum pigmented, asphalt roof coating. Fiber reinforced, rubberized Adhesive NOA No: 03- 0501.02 U 1 Expiration Date: 11/06/08 Approval Date:10 /23/03 Page 5 of 32 APPROVED INSULATIONS: Product Name GA1. TEMP Isotherm R, RA, RN & Composite, EnergyGuard RA GAFTEMP® Composite A & N (BMCA)GAFTEMP® Fiberboard GAFTEMP® Permalite GAFTEMP GAFCANTTm GAFTEMP Permalite Recover Board GA.F1'k,MP GAFEDGETM Tapered Edge Strip (BMCA) GAFTEMP® High Density Fiberboard BMCA EnergyGuard, RA BMCA Composite EnergyGuard, RA PYROX White Line ACFoam I,11 & Composite ISO 95+ ISO 95+ Composite EPS Wood Fiber High Density Wood Fiberboard Pelite/Urethane Composite Perlite Insulation Dens Deck ENRG'Y -2 & E'NRG'Y -2 PLUS, UltraGard Gold • •o • • • • • • • • • •• • • •• • • • • TABLE 2 • • • • ••• ••• ••• Product Description •• • • • Polyisocyanurate foam insulation: ••• • • • ••• • • • •• •• • • • • ••• • • • • • • • • • ••• • • • • ••• •. •• •• Polyisocyanurate foam insulation with high density fiberboard or Permalite perlite insulation. Fiberboard insulation. Perlite insulation board. Cut perlite board Perlite recover board Tapered perlite board High density wood fiberboard insulation. Polyisocynurate foam insulation Polyisocynurate/wood fiberboard composite Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate /perlite ridged insulation Extruded polystyrene insulation Wood fiber insulation board Wood fiber insulation board Perlite / urethane composite board insulation Perlite insulation board Water resistant gypsum board Polyisocyanurate foam insulation • • • • • • • • • • • • 0 • • • • • • • • • • • • • • • o • • • Manufacturer . ..(With Current NOA) (t • F Materials Corp. • • • • •••• GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. BMCA BMCA Apache Products Co. Apache Products Co. Atlas Energy Products Firestone Building Products, Inc. Firestone Building Products, Inc. Generic Generic Generic Generic generic G -P Gypsum Corp. Johns Manville NOA No: 03- 0501.02 Expiration Date: 11/06/08 Approval Date:10/23 /03 Page 6 of 32 APPROVED INSULATIONS: Product Name FiberGlass Roof Insulation Glass fiber/Mineral fiber insulation •• • • • •• ••• ISORoc Polyisocyanurate foal ./ t c & c i :. • • • Structodek Multi -Max & FA Paroc Base Board Paroc Cap Board APPROVED FASTENERS: Fastener Number 1. 2. 3. 4. 5. 6. 7. 8. 9. Product Name GAFTTI'E® (Drill -Tec ®) #12 Standard & #14 Heavy Duty Roofing Fastener GAFTPTE® (Drill -Tec ®) ASAP GAFTITE® (Drill -Tec ®) Base Sheet Fastener and Plate Galvalume Plates (Drill - Tec® Metal) Polypropylene Plates (Drill -Tec® Plastic) Dekfast Fasteners #12, #14 & #15 Dekfast Hex Plate Dekfast Lock Plate #12 Roofgrip Fasteners 10. Metal Plate 11. Gearlok Plastic Plate 12. Glasfast Fastener TABLk 2 . .• ••. • • • • • • Product R es }ptio9 • • - - • • • composite insulation • • • • • • Wood fiber insulation board Polyisocyanurate roof insulation Rockwool insulation TABLE 3 Product Description Insulation fastener for steel, wood & concrete decks. Pre - assembled GAFTITE Fasteners and metal and plastic plates. Base sheet fastening assembly. Round galvalume stress plates. Round polypropylene stress plates. Insulation fastener for wood, steel and concrete decks Galvalume hex stress plate. Polypropylene locking plate. Insulation fastener for wood and steel. Galvalume stress plate. Polypropylene round plate Insulation fastener assembly with recessed plastic plate • • ••• • • • ••• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • ••• • • • • • • • • • • • • • • • • • • • • • ••• • • • • • • ••• Dimensions 2 7/8" x 3 1 /a" 3" x 3 /a" 3" round 3" square 3.2" • •• • • • • • • • •• iti anufacturer •.• .• ( With Current NOA) Johns Manville • johns Manville Masonite. RMax, Inc. Partek, Inc. Manufacturer (With Current NOA) GAF Materials Corp. GAF Materials Corp. GAF Materials Corp. 3" and 3 GAF Materials Corp. 3" and 3 GAF Materials Corp. Construction Fasteners Inc Construction Fasteners Inc. Construction Fasteners Inc. ITW Buildex Corp. ITW Buildex Corp. ITW Buildex Corp. Johns Manville NOA No: 03 0501.02 Expiration Date: 11/06/08 Approval Date:10 /23/03 Page 7 of 32 APPROVED FASTENERS: Fastener Product Number Name 13. Olympic Fastener #12 & #14 14. Olympic Fastener ASAP 15. Olympic Polypropylene 16. Olympic G -2 17. Olympic Standard 18. Insul -Fixx Fastener 19. Insul -Fixx S Plate 20. Insul -Fixx P Plate 21. Tru -Fast 22. Tru -Fast Plates 23. Tru -Fast Plates EVIDENCE SUBMITTED: Test Agency Factory Mutual Research Corp. Factory Mutual Research Corp. Trinity Engineering PRI Asphalt Technologies, Inc. IRT of S. F1. IRT of S. Fl. TAIRA 3 •• • • Product • • ••. ••• Description Insulation fastener.. . Pre- assembled InWattort fastener and plate Polypropylene plastic plate 3.5" round galvalume AZ55 steel plate 3" round galvalume AZ50 steel plate Insulation fastener for steel and wood decks 3" round galvalume AZ50 steel plate 3" round polyethylene stress plate Insulation fastener for steel and wood decks 3" round galvalume AZ55 steel plate Polyethylene plastic plate Test Identifier Current Insulation Attachment Requirements FMRC 4470 - PA 114 Wind Uplift PA 114 GAF -020 -02 -01 02-005 02 -014 • .•. • • • • • • • • • • • • • • • • • • • • • ••• • • • • • • • • ••. • • • ••. • • • • ••. • • • •• •. • • . • • • • • • • • • • • o • Manufacturer • iimensions (With Current NOA) • • ••• C11vmpic Manufacturing • • • • • ••• • • Group, Inc. glympic Manufacturing Group, Inc. 3.25" round Olympic Manufacturing Group, Inc. 3.5" round Olympic Manufacturing Group, Inc. 3" round Olympic Manufacturing Group, Inc. SFS /Stadler 3" round SFS /Stadler 3" round SFS /Stadler The Tru -Fast Corp. 3" round The Tru -Fast Corp. 3" round The Tru -Fast Corp. Description Date FMRC 1996 01.01.96 J.I. 1B9A8.AM 09.04.97 J.I.3D4Q2.AM 04.30.97 4483.04 97 -1 06.06.97 ASTM D 4977 02.01.02 TAS 114 01.18.02 TAS 114 03.22.02 NOA No: 03- 0501.02 Expiration Date: 11/06/08 Approval Date:10 /23/03 Page 8 of 32 • Fastening Options: GAF1'T1'E #12 or #14 Screws and 3" Plates are installed throufh the base s;eet • • . and insulation in 3 rows 12" o.c. One row is in the 2" side lap. •'Fhe ether rptvs ' . ' • are equally spaced approximately 12" o.c. in the field of the sheet a'Maximiim '' • • Design Pressure —45 psf, See General Limitation #7) • GAFTITE #12 or #14 Screws and 3" Plates in 4 rows 12" o.c. Oji�,rpw is irjtlfe,. • • • 2" side lap. The other rows are equally spaced approximately q,';p,c. in the field . • • • of the sheet. (Maximum Design Pressure —60 psf, See General.Camt}ation #7) • • GAFT1'1'E #12 or #14 Screws and 3" Plates are installed througti'thr1 se sheet • • and insulation in 4 rows 8" o.c. One row is in the 2" side lap. The other 3 rews : • are equally spaced approximately 9" o.c. in the field of the shed. £kfaximum� •• • Design Pressure —75 psf, See General Limitation #7) • • • • Membrane Type: APP /SBS Heat Weld Deck Type 1I: Wood, Insulated Deck Description: 19/ or greater plywood or wood plank System Type D (1): Insulation and Base sheet simultaneously attached All General and System Limitations shall apply. One or more layers of any of the following insulations. Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft ACFoam•I, ENRGY 2, GAFTEMP® Isotherm R, ENRGY 2 Plus, GAFTEMP Isotherm RA, EnergyGuard, EnergyGuard RA GAFTEMP Isotherm RN, GAFTEMP Composite, GAFTEMP Composite A, GAFTEMP Composite N loosely laid with firmly butted joints. Minimum thickness, 1.3 ". GAFTEMP High Density Fiberboard, GAFTEMP Fiberboard, minimum thickness 1 ". Base Sheet: Install one ply of GAFGLAS® #75, GAFGLAS #80 Ultima Base Sheet, GAFGLAS® STRATAVENT® Eliminator Perforated or RUBEROID® 20 base sheet applied over the loose laid insulation with 2" side laps mechanically fastened to deck as described below; c:TogMEN DEC 2 7 2006 BY: -_ Q'l(°'. Ply Sheet: (Optional, required when using RUBEROID 20) One or more plies GAFGLAS PLY 4 ®, GAFGLAS Flex Ply 6 sheet or GAFGLAS #80 Ultima adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs. /sq. Membrane: One ply of Ruberoid® Torch Smooth, Ruberoid® Torch Granule, Ruberoid® Torch Plus Granule or Ruberoid® Torch FR torch applied according to manufacturer's application instructions. Or One or more plies of RUBEROID® SBS Heat- We1dTM PLUS, RUBEROID® SBS Heat- We1dTM PLUS FR, RUBEROID® SBS Heat- We1dTM 170 FR, RUBEROID® SBS Heat- We1dTM, RUBEROID® SBS Heat- We1dTM Smooth, RUBEROID® U1traCladTM SBS and RUBEROID® SBS Heat- We1dTM 25 applied according to manufacturer's application instructions. NOA No: 03- 0501.02 Expiration Date: 11/06/08 Approval Date:10/23 /03 Page 24 of 32 Surfacing: (Optional) Install one of the following: 1. Gravel or slag applied at 400 lb./sq. and 300 lb. /sq. respectively in a flood coat of approved asphalt at 60 lb./sq. 2. GAF Premium Fibered Aluminum Roof Coating, at 1.5 gal. /sq. or GAF WeatherCoat Emulsion at 3 gal. /sq. (Torch Smooth applications only) 3. GAF Weathercote® MB +(Matrix 715 MB Coating), Applied at 1 to 1.5 gal. /sq. 4. Top Coat® Surface Seal SB(Matrix 602 SB Coating), Applied at 1 to 1.5 gal. /sq. Maximum Design Pressure: See Fastening Above • • • • • .• • • • • .• •• • •• • • • • • • • •••• •• • • • • • • • •.•• • •• ... • •. •• • • • • . • •• •• • • • • •••• • • • •••• .. • • • • NOA No: 03- 0501.02 Expiration Date: 11/06/08 Approval Date:10/23 /03 Page 25 of 32 WOOD DECK SYSTEM LIMITATIONS: GENERAL LIMITATIONS: • • ••• • • • ••• •• •• • • • •• •• • • • • • • • • • • • • • . • • ••• • • • • • • • • • • • • • ••• • • • • ••• • . •• 1 A slip sheet is required with Ply 4 and Flex Ply b we used'�s Er rrkchaOii l�y.fastened base or • • • • • • • • anchor sheet. • • • • • • • • • • • 2. Minimum 'A" Dens Deck or 1 /2 Type X gypsum board is acceptable to be wood deck. •• • • • •• ••• •• • • • • • •• • • • • • ••• •• 1. Fire classification is not part of this acceptance, refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs. /sq., or mechanically attached using the fastening pattern of the top layer 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each sidelap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf. 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field - tested, are below 275 lbf. insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida Registered Engineer, Architect, or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. 7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117. (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform with Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 9B -72 of the Florida Administrative Code. END OF THIS ACCEPTANCE NOA No: 03- 0501.02 Expiration Date: 11/06/08 Approval Date:10 /23/03 Page 32 of 32 .1•� 4 ROOF COVERING MATERIALS (TEVT) it uvr l.uvtntNj MAMMAL) 1rcvII ROOFING SYSTEMS (TGFU)— Conlinuerd • • ••• • R4OFIN TEt.15 (TGFU).— Continued J � Sr` ltyase Sheet (Optional): One or more layers Type G1, G7. or G3, • ti. 1 =/33 :•••: : Incline: 1/2 Membrane: One or more layers. of "Rubcroid Torch" (smooth or granule), ;InsQlatiaA tOQtion;�): ISnc;nnurste, polite or glass fiber, any thickne' --, "Ruberoid Torch Plus" (granule), "Ruberoid Mop" (granule) or "Ruberoid • •hcreeneopepeck or inecleaniereely fastened in place. Joints offset 6 in. Mop Plus" (granule). Base Sheet: One or ntor•1 layers of Type 62 "GAFGLAS x75 Base Sheet", Coating: Karnak No. 91, 1-1/2 - 3 gal /sq. hot mopped or mechanically fastened in place. 4. Oeck: 015/32 Incline: 1/2 • Ply Sheet: Owe or new lsyetre of Type G1 "GAFGLAS Ply 4' or "I'ly 6 ", hot Insulation: One or more layers partite, glass fiber, isocyanurate, urethane,• • • tr R mgp1fi=1 in'p� ale. • • • perlite /isucyanurar:e composite, perlite /urethane composite, phenolic, • • Mernbeanelrberc•d sr,r•I • 6R" (granule). 1-1/2 in. mm thickness (offset from plywood joints 6 in.). ••• i ng IVVFtionale: Aluminum Coating at 1-1/2 gal /sq or Base Sheet: One or more layers of lype G2 ur 63. GAF Weather Cnat Emulsions al 3 gal /sq. Ply Sheet (Opttmnal): One or mere layers of Type 61. 13. Deck: NC Incline: 1/2 Membrane: One or mere layers of "Ruberoid Torch" (smooth or granule), Insulation (Optional): (ocy.snurale, wood fiber bo.ird, perlite, glass "Ruberoid Torch Plus" (granule), "Ruberoid Mop' (smooth ur granule) or ••• • fiDer tin 1Ajjk ;t, fiet or mechanically f, »tened in pea'e. "Ruberoid Mop Plus" (granule!). • •sleines offset 1 ice • Surfacing: Karnak No. 97, 1-1/2 - 3 gal /sq. • • 83s4SIjc4: r o more ;leeers uf Type 62 "GAFGLAS 475 Base Sheet ", 5. Deck: NC Incline: 1/2 •• • het nneppetl it places. •• Base Sheet (Optional): One or rnure layers of Type 61, G2 or 63. Ply Sheet (Optional): One or more layers of Type 61 "GAFGI AS Ply 4" or Membrane: One or more Layers of "Ruberoid Torch" (smnuth or granule), "Ply 6" hut mopped in platrt. "Ruberoid Torch Plus" (granule). Membrane: "Rubernid lurch :'k" (granule). Surfacing (Optional): Karnak "No. 97" or "169" at 1.3 gal /sq or Grundy Surfacing (Optional): "GAF libeled Aluminum Coaling" at 1-1/2 gal /sq Ind. "20 F Entulsiun" at 3 gal /sq. or GAF Weather Coat Emulsion at 3 gal /sq. 6. Deck: C -15/32 Incline: 1/2 14. Deck: NC Incline: 1/2 Insulation: One or more layers perlite, glass fiber, 3/4 in. mire, Insulation (Optional): Trocyanurate, wood fiber board, perlite, glass isocyanurate, urethane, perlite /isocyanurate composite, perlite /urethane fiber, any thickness, hot mopped or mechanically fastened in place. composite, phenolic, 1.1/2 in. min. Joints offset 6 in. Base Sheet (Optional): One or more layers of Type 61, G2 or 63. Base Sheet: One or more layers of "GAFGLAS 475 ease Sheet ", hot Membrane: One or more layers of "Ruberoid Torch" (smooth or granule), mopped in place. "Ruberoid Torch Plus" (granule), "Ruberoid Mop' (smooth or granule) or " Ply - Sheet (Optional): One or more layers of "6AF GLAS Ply 4" or "Ply 6" hot mopped in place. Membrane: "Rubernid Torch FR" (granule). Surfacing (Optional): GAF Weather Coat Emulsion applied at 3 gal /s:1 nr GAF fibered Aluminum Coating at 1-1/2 gal /sq. 15. Oeck: C -15/32 Incline: 1/2 o' Insulation (Optional): Perlite, fiber glass, isocyanurate, urethane, perlite/ isocyanurate composite or phenolic. Base Sheet: One or more layers Type G2 or G3 base sheet, hut mopped or mechanically fastened. Ply Sheet (Optional): One or snore layers Type 61, hot mopped in place. • Membrane: "Rubernid Mop FR' or "Ruberoid Mop 170 FR" (granule). '. Deck: C -15/32 incline: 1/2 0 + Tonal): Perlite, fiber glass, isocyanurate, urethane, perlite/ isocyanurate composite or phenolic, offset 6 in. from joints. Base Sheet: One ur Inure layers of Type G -2 or 6 -3 base sheet, hot mopped or mechanically fastened. Ply Sheet (Optional): One or more layers uf f;'pe 6-1, hot mopped it place. Membrane: One layer of "Rubernid Torch' or "R,Iberoid Mop' (smooth). Membrane: One layer of "Ruberoid Torch FR' or "Ruberoid Mop FR' (granule) 17. Deck: NC Incline: 1 • Insulation (Optional): Perlite, fiber glass, wood fiher, isocyanurate urethane, perlite /isocyanurate composite or phenolic. Base Sheet: One or more layers Type G2 or 63 base sheet, hot moppet or mechanically fastened. Ply Sheet (Optional): One or more layers Type GI, hot mopped in place Membrane: One layer of "Ruberoid Mop FR" or 'Ruberoid Mop 170 FR (granule). 18. Deck: NC incline: 1/2 Insulation (Optional): Perlite, fiber glass, wood fiber, isocyanurate urethane, perlite /isocyanurate composite or phenolic. Base Sheet (Optional): erre or more layers ut Tyee G -2 or 6 -3 bas• sheet, hot mopped or mechanically fastened. Ply Sheet (Optional): One or more layers of Type G -1, hot mopped iI place. s pp Membrane: One layer of "Rubcroid Torch" (smooth), "Ruberoid Mup (smooth). Membrane: One layer of "Ruberoid Torch FR ", "Ruberoid Mop FR" u "Ruberoid Mop 170 FR" (granule). 19. Deck: NC incline: 1/2 Insulation (Optional): One or I re layers of perlite, glass fiber isocyanurate, urethane, perlite; /isn.•;anurate rornp0Site er phenolic, 411 thickness. Rase Sheet: (inc or more pllc: ,1 or (2, hot snopprd or adhered wit Karnak Che rii, at Co. "No. 81' on 6ibson•Homan 'No. 6160" cold apptie arllr:sive at 1 -I/2 gal /sq. Membrane: One layer of "Ruheruisl Mop FR" or "Ruberoid Mop 170 FR (yranul?), hot plopped ur adhered with Karnak Chemical Co. "No. 81" c Gibson -Homan "No. 6160' cold applied adhesive at 1-1/2 gal /sq. 20. Deck: C -15/32 incline: 1/4 Insulation: Polyisocyanurate, any thickness. Base Sheet: "GAFGLAS 4/5" (Type G2), mechanically attached. LOOK FOR MARK ON PRODUCT urfacing: Gravel. ck: C -15/32 Incline: 1/2 Insulation (Optional): One or more layers perlite, wood fiber, glass fiber, isocyanurate, urethane, perlite /isocyanurate composite, perlite/ urethane composite, wood fiber /isocyanurate composite, phenolic. Base Sheet: Two or more layers of Type G2 or G3. Ply Sheet (Optional): One or rnure layers of Type 61. Membrane: One or more layers of "Ruberoid Torch" (smooth or granule), "Ruberoid Torch Plus" (granule), "Ruberoid Mcp" (smooth or granule) or "Ruberoid Mop Plus" (granule). Surfacing: Karnak No. 97, 1-1/2 - 3 gal /sq or gravel. Deck: NC Insulat • , • more layers perlite, glass fiber, 3/4 in. min, yanurate, urethane, perlite /isocyanurate composite, perlite /urethane composite, phenolic, 1 -1/2 in. min. Base Sheet (Optional): One or more layers of Type GI, G2 or G3. Membrane: One or more layers of "Ruberoid Torch" (smooth or granule), "Ruberoid Torch Plus" (granule), "Ruberoid Mop" (smooth or granule) or "Ruberoid Mop Plus" (granule). Surfacing: "Al MB Aluminum Roof Coating" at 1-2 gal /sq. Deck: C -15/32 Incline: 1/2 Insulation (Optional): One or more layers perlite, glass fiber, 3/4 in. min, isocyanurate, urethane, perlite /isocyanurate composite, perlite/ urethane composite, phenolic, 1-1/2 in. mill. Base Sheet: One or inure layers of Type G2 "GAFGLAS 475 Base Sheet", hot mopped or :iwcharnically fastened in place. Ply Sheet: One or more layers of Type 61 "GAFGLAS Ply 4 ", hot mopped in place. Membrane: "Ruberoid Mop FR" (granule). Surfacing (Optional): GAF Fibered Aluminum Coating at 1 -1/2 gal /sq or GAF Weather Coat Fnu.rlsion at 3 gal /sq. 10. Deck: C -15/32 Incline: I/2 Insulation (Optional): One or more layers perlite, glass fiber, 3/4 in. min, isocyanurate, urethane, perlite /isocyanurate composite, perlite/ urethane composite, phenolic, 1 -1/2 in. min. Base Sheet: One or more layers of Type G2 "GAFGLAS 475 Base Sheet ", hot mopped or mechanically place. in lace. Ply Sheet: One or more layers of Type G1 "GAFGLAS Ply 4 ", or "GAFGLAS Ply 6" hot mopped in place. Membrane: "Ruberoid Torch FR" (granule). Surfacing (Optional): GAF Fibered Aluminum Coating at 1 -1/2 gal /sq or GAF Weather Coat Emulsion at 3 gal /sq. Deck C -15/32 Incline: 1/2 Insulation: Isucyanurale, 2 in. min., wood fiber, perlite or glass fiber, any thickness, hot mopperl or rnechanically fastened in place. Joints offset 6 in. Base Sheet: One or more layers of Type G2 "GAFGLAS 475 Base Sheet ", hot mopped or mechanically fastened in place. Ply Sheet (Optional): One or more layers of Type G1 "GAFGI AS Ply 4" or "Ply 6" hot mopped 111 place. •• Membrane: "Ruberoid Torch FR" (granule). Surfacing (Optional): GAF Fibered Aluminum Coating at 1 -1/2 gal /sq or .AF Weather Coat Emulsion at 3 gal /sq. 1524.1 As it pertains to this section, it is the responsibiity 4 jhe r gfir:tg - to provide the owner with the required roofing permit, and to explain to the owner the content of this section... The provisions of Chapter 15 of the Florida Building Code, Building govern the minimum requirements and standards of the industry for roofing system installations. Additionally, the #oIIQyinv ten shouki be addressed as part of the agreement between the owner and the contractor. The o1nor'g Oita: lo tre adjacent box indicates that the ite � - been explained. • • ••• • • 1. Aesthetics- Workmanship: The workmanship provisions of Chapter 15 (High Velocity Hurricane ( 9 tY Hu Zone) are for the purpose of providing that the roofing system meets the wind resistance and water intrusion performance standards. Aesthetics (appearance) issues are not a consideration with respect to workmanship provisions. Aesthetic issues such as color or architectural appearance, that are not part of a zo ng « • • e, should be addressed as part of the agreement between the owner and the contractor. 11 . Renailing Wood Decks: When replacing roofing, the existing wood roof deck may 9 ay have to be renailed in accordance with the current provisions of Chapter 16 (High Velocity Hurricane Zones) of the Florida Building Code. (The roof deck is usually concealed prior to removing the existing roof system). ommon Roofs: Common roofs are those which have no visible delineation between neighboring units (i.e. townhouses, condominiums, etc.). In buildings with common roofs, the roofing contractor and/or owner should notify the occupants of adjacent units of roofing work to be performed. 4. Exposed Ceilings: Exposed, open beam ceilings are where the underside of the roof decking can be viewed from below. The owner may wish to maintain the architectural appearance; therefore, roofing nail penetrations of the underside of the decking may not be acceptable. The Florida Building Code pro es the option of maintaining this appearance. 5 onding Water: The current roof system and/or deck of the building may not drain well and may Muse water to pond (accumulate) in low -lying areas of the roof. Ponding can be an indication of structural distress and may require the review of a professional structural engineer. Ponding may shorten the life expectancy and performance of the new roofing system. Ponding conditions may not be evident until the ons'.al •ofing system is removed. Ponding conditions should be corrected. 6. • erflow scuppers (wall outlets): It is required that rainwater flows off so that the roof is not overloaded from a build up of water. Perimeter /edge walls or other roof extensions may block this discharge if overflow scuppers (wall outlets) are not provided. It may be necessary to install overflow scuppers in ce with the Florida Building Code, Plumbing. 7. Ventilation: Most roof structures should have some ability to vent natural airflow through the interior of the s ral assembly (the building itself). The existing amount of attic ventilation shall not be reduced. It ma be • - ne icial • sider additional venting which can result in extending the service life of the roof ' I • • • ••• • • • • •• •• • • • • • • • • •• • • • • • • • • • • SECTION;1524 • : ; : • • HIGH VELOCITY HURRICANE ZONES REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIONS JI ■: % ' r VL 7 �� '1! rs/Ag "nt's..S : rat% re qqq ( 4 - 57 " Property Address • • • • • •• • • • • • • • • • • • • • • • • • • • • • Date on actor's Sign re CCU Process Number .. .. .. • . THESE PLANS ARE • :IfEING PROCESSED BY: • • ••• pediting by Tonya, LLC . :: • • • y1an & Permit Processing � � , IV ' 78'6.290.1908 or 786.229.5346 opiet xpedbytonya @yahoo.com RE -ROOF FLAT DECK ONLY JAN 1 6 2001 Passed Inspector Comments All tiles to be replaced due to flat reroof must be installed by final inspection. 1/12/07 CG. Failed W 4111 Correction Needed Re- Inspection Fee ($75) No Additional Inspections can be scheduled re- inspection fee is paid. until Inspection :Number IN,SiI'• Inspection Date: 01/12/2007 Inspector: Grande, Claudio Owner: MARTINEZ, AURELIO PEDRO Job Address: 999 94 Street NE Project: <NONE> Miami Shores Village, FL Contractor: STAR ROOFING OF ORLANDO INC Building Department Comments Friday, January 12, 2007 Inspection Worksheet Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL Phone: (305)795 -2204 Fax: (305)756 -8972 Block: err itiN tuber ;.R -12 =06 -3041 Permit Type: Roof Inspection Type: Final Roof Work Classification: Roof - New Phone Number Parcel Number 1132060350010 Lot: Phone: (786)290 -1908 Page 1 of 1