ROOFINGMIAMI SHORES VILLAGE
BUILDING INSPECTION DEPARTMENT
APPLICATION FOR BUILDING PERMIT
Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the build -
ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami
Shores Village, Florida, and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and
regulations of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved
plans and specifications must be kept at building during progress of the work.
ss `r -3 ,19..--
Owner's Name and Address .. L�.'. %'+`J..ln r . �s � ... No 7G
i�
Registered Architect and /or Engineer.........P et: /!' c T o �� C 1
1.// ... ..S ..._
Name and address of licensed contractor S .) ->
Location and legal description of lot to be built on:
Lot Block Subdivision
Street and Number where work is to be done 7 6.!
State work to be done and purpose of building (by floor ;)..._ /f
and for no other purpose.
New Building Remodeling Addition Repairs - RC= �' ✓ o. of Stories
To be constructed of Kind g f foundation Roof Covering
Estimated Total cost of improvements $ 6..0 Amount of Permit $.
Zone cubage required _Plan Cubage
Distance to next nearest building Size of Building Lot
Maximum live load to be borne by each floor
I hereby,..submi all the plans a spec' ations for
3... o said building. All notics w j refer nce to the building and its nstruction may
l -
be sent to'.e /Yi) e /..) C.' l l ✓.2 A- Lai .V „5 ....... .
The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer
of labor under the Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement,
and has complied with the provisions thereof, and will require similar compliance from all contractors or sub -con a ors employed by him
in the work to be performed under this permit; and will post or cause to be posted for insp o on t he w•r ch public notice
or notices as arc required by the Act. The undersigned agrees to employ only such�ubepn i rlf/ • rmed under this
pennit, as are licensed by Miami Shores Village.
Remarks (Signed)
STATE OF FLORIDA,
COUNTY OF DADE. ss.
Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap-
peared
and who, being by me first duly sworn, upon oath deposes and says that he is the.
of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts
therein by him state are true.
Permit No
Disapproved
(Signed)
Date
Date
P
Building Inspector
Chairman
Mcrnber
Member ...... _----- - --- -.
Council Approved Date
r»
ad, Sworn to and Subscribed before me.
Notary Public, State of Florida
NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval
the Planning Board.
A re in fee of 31.00 will be charged when such re- inspection is made necessary by improper notice
materials and /or workmanship.
0 .
to me well known,
My Commission Expires
PLANN)NC BOARD _.._ DATE
Member
Member .
Member .._ .._—
Disapproved Date
has been obtained from
for inspection or faulty
Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the building or other structure herein
described. This application is made in compliance and conformity with the Building Ordinance of Miami Shores Village. Florida, and all provisions of the Laws of the
State of Florida, all ordinances of Miami Shores Village and all rules and regulations of the Building Division of Miami Shores Village shall be complied with. whether
herein specified or not. A copy of approved plans and specifications must be kept at building during progress of the work.
Owner's Name and Address
New Building Remodeling
APPLICATION FOR BUILDING PERMIT
MIAMI SHORES VILLAGE
BUILDING INSPECTION DEPARTMENT
State work to be done and purpose f building (by floors), state exterior colors (submit samples)
Remarks (Signed)
Date P 19
Afsi jeduit No. 2� / Street
Registered Architect and/or Engineer
Name and address of licensed contractor R e l i /
v 6 4t r' ^ A C . / 4 7v t d . f i ' - ��f'
Location and legal description of lot to be built on: • . " oo
Lot (. Block die Subdivision M R• 4i // S Zj // .2/ / 5 a
!L6
Street and Number where work is to be done ' ( si•� • 9 „$ z "/'
.a. 1 /4
�) de-le -% - /4tis /77( 2` ', 1-(, toe, ; °. `'.
t
Repairs No.
°� o. of Stories
To be constructed of Kind of foundation Roof Covering 1 .7 IV X 441
O 0 - eX f S /
�
Estimated Total cost of improvements $ [� 2 oo, Amount of Permit $ �`
Zone cubage required Plan Cubage 'T 0 / 7 lie
Distance to next nearest building Size of Building Lot 7//f
Maximum live load to be borne by each floor
I hereby submit all plans and specifications for said building. All notices with reference to the building and its construction may be sent to
Addition
The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligatons as an employer of Labor under the Florida Workmen's
Compensation Act. being Section 5966, Compiled General Laws of Florida, Permanent Supplement, and has complied with the provisions thereof, and will require similar
compliance from all contractors or sub - contractors employed by him in the work to be perfor der this 't; and will post or cause to be posted for inspection
on the site of the work such public notice or notices as are required by the Act. The undersigned a e m y only such subcontractors, on work to be performed
under this permit, as are licensed by Miami Shores Village 3CZ"2` -3'7C
'' C /7Z Z.
STATE OF FLORIDA
COUNTY OF DADE. } ss.
Before me, the undersigned authority, a notary public. duly authorized to administer oaths and take acknowledgments, personally appeared
to me well known.
and who, being by me first duly sworn, upon oath deposes and says that he is the
of the above described construction, that he has carefully read the foregoing application. and that he did sign the same. and that all facts therein by him stated are true.
d-
Date
Read, Sworn to and Subscribed before me.
Permit No. .7g7 c-2/ Date
Disapproved
(Signed) 5�
Building Inspector My Commission Expires
PLANNING BOARD DATE
Chairman Member
Member Member
Member Member
Council Approved Date Disapproved Date
NOTE: A charge of $25.00 will be made for making corrections or changes to this application after approval has been obtained from the Planning Board.
A re- inspection fee of $25.00 will be charged when such re- inspection is made necessary by improper notice for inspection or faulty materials and/or workmanship.
Notary Public, State of Florida
y PERMIT APPLICATION FOR MIAMI SHORES VILLAGE
Date / -26-91 C Job Address (01 IVtL. 1.5 Tax Folio
Legal Description LOT (5 1 W1/2 of tai- go R IL Cog / am/ //Lt J , - 3ArrK,e /0 / 68
�thvnet / Lessee / Tenant I i2 • F M 2 - ?¢/V iL(N S Master Permit # ` ; i
``. Owner's Address P/ . 95 Phone 75C - $3' 3
Contracting Co. / Q4- 6U4Cs J 4 , (lc 1. Ck 5 Address 4 4 , 55 5 �4�'• 7?i
7+
nn
Qualifier VANS Al g , C I'6 5 ss# Phone 57.5 .5 4s'
State # C6(OO425 Municipal # Competency # Ins.Co.
Architect /Engineer Address
Bonding Company Address
Mortgagor Address
Permit Type(circle one): BUILDING ELECTRICAL PLUMBING MECHANICAL ROOFING PAVING PENCE SIGN
WORK DESCRIPTION 3066 66T 9 goo Ho A
(A ),4 11, gin- C(L4yy + .2 - t, (h .
Square Ft. - 150 Estimated Cost(value) /d 0'. 0
WARNING TO OWNER: YOU MUST RECORD A NOTICE OF COMMENCEMENT AND YOUR FAILURE TO DO
SO MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY (IF YOU INTEND
TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR
NOTICE OF COMMENCEMENT).
Application is hereby made to obtain a permit to do work and installation as indicated above, and
on the attached addendum (if applicable). I certify that all work will be performed to meet the
standards of all laws regulating construction in this jurisdiction. I understand that separate
permits are required for ELECTRICAL, PLUMBING, SIGNS, POOLS, ROOFING and MECHANICAL WORK.
OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will
be done in compliance with all applicable laws regulating construction and zo g. Purtrermore, I
author' a the a ove -na d co tractor to do the work sta
Signature
Date:
Signature of owner paid /or Condo President
Date:
Notary as to
My Commission 'x
** * * *
FEES: PERMIT
APPROVED:
C.C.F.
Fire
Zoning Buildin
Mechanical Plumbing_
/14 / CO 1.14A 70 it
Notary a
My Comm
Other
Electrical
Engineering,
0 01/25/95 15:02
PERMIT NO.
STATE OF FLORIDA:
COUNTY OF DADE:
2. Description of improvement: 1'1 Q.
3. Owner(s) name and address:
l \
Interest in property:
Name and address of fee simple titleholder:
A. Contractor's name and address:��4
6. Lender's name and address:
$305 559 6602 • .CO.P`- PI INTTNG
•
Notary Public
My Commission Expire
NOTICE OF COMMENCEMENT
TAX FOLIO NO. \ \ 3 a n(o c)\-1 Q. \5 C
95R034470 1995 JAN 26 12:22
THE UNDERSIGNED hereby gives notice that improvements will be made to certain real property, and in accordance With
Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement.
1. Legal description of property and street address: 5J d- W \ `�
• ••
fit•
•
S
5. Surety:(Payment bond required by owner from contractor, if any)
Name and address:
Amount of bond $
7. Persona within the State of Florida designated by Owner upon whom notices or other documents may be served as provided
by Section 713.13(1)(a)7., Florida Statutes,
Name and address: _
8. In addition to himself, Owner designates the following person(s) to receive a copy of the Lir .:.pr's Notice as provided in Sec-
tion 713.13(1)(b), Florida Statutes.
Name and address: _
9. Expiration date of this Notice of Commencement: (the expiration date is 1 year from the date of recording unless a
different date is specified)
"7(08 -(7 -70 b
-4�Qz42 h\
Signature of Owner
Sworn to and subscribed before me this 2 day of u.4 ' 1.19 ?' OtPO4, MiZr/19
c ac
STATE OF FLORIDA, ez1 °,�ti'?'"F Ar �
NEIIVIV CEi3TP" Bi.o' ' :;a. Y' ;, : e'' . •
or .iaciflod its "•i:'s c :i" °❑ /JC Ij • n`
C
By
7(o (Nh. S s T.
j✓1rD'
9‘ / c -/ -t ,
2 00 1 /001
Job Address: - 4c,. 1 04. 9 9
APPENDIX 'E'
METRO -DADE UNIFORM BUILDING PERMIT
SECTION II
MORTAR OR ADHESIVE SET TILE SYSTEMS
1. General
Contractor:
The information provided in this Section is required to confirm
Product Control Approval of the proposed tile system assembly;
confirm compliance with the wind load requirements of Chapter 23
of the South Florida Building Code (SFBC); and confirm compliance
with Sections 3403.5 and 3404 of the South Florida Building Code.
2. Documentation
The following documents are required for submission with the
Uniform Building Permit application:
► Two (2) copies of the proposed tile system assembly's and
associated roofing component's Product Control
Approval(s).
► One (1) copy of the tile system assembly and/or roofing
component(s) manufacturer's published application
instructions and literature.
► All documents attached herein, filled out and completed in
full.
3. Project Information
Check one of the following:
❑^/ New Construction
11b�" Re -Roof
Note: Mortar or adhesive set tile systems are not acceptable as recover
applications.
Mortar or Adhesive Set Tile Systcms
Page - 1
Process No.
Is the deck solid s thed? (circle 'yes' or 'no')
yes no
Deck Type (check one of the following):
❑ Nominal 1/4" Plywood (for re -roof only)
❑ Nominal 3 ' 8 " Plywood
[ Wood Plank "
❑ Other (fill in)
Roof Pitch (fill in):
Z " : 12"
Note: Mortar or adhesive set tile systems shall not be installed at a pitch
greater than 71/4":12 ". Mortar or adhesive set tile applied at a
pitch greater than 5 ":12" and less than or equal to 7 ":12" shall
have the first three courses of tile nailed with not less than one
nail per tile. As an alternate, the first three courses of tile may be
applied in mortar over a single layer of minimum 12 ga. wire
mesh with square openings of not less than 3 / 8 " which is
mechanically attached to the sheathing with not less than one nail
per 2 ft
Circle 'yes' or 'no' for each of the following:
Have you attached two copies of the tile system manufacturer's
Product Control A roval for the proposed tile system?
Ives no
Have you attached a copy of the tile system assembly and/or
roofing component(s) manufacturer's published, application
instructions and other literature
no
Is the proposed underlayment approved for use with this tile
system assembly?
no
Job Address: Contractor:
Project Information (continued):
If the proposed underlayment is self - adhered, have you complied
with the venting requirements of Section 2913.3 (b), (c) and (d) of
the South Florida Building Code?
yes no
Are all related accessories approved for use with this tile system
assembly?
Are the proposed edge metal attachment fasteners in compliance
with the requirements of the South Florida Building Code (minimum
12 ga. annular ring shank, corrossion reisistant nails)?
�ve�s no
4. The Tile System Assembly:
The following information is required to confirm compliance with
Subsections 3403.5(a) and (c) and Section 3404 of the South Florida
Building Code.
Tile:
Tile Name:
Manufacturer:
s ()s no
Mortar or Adhesive:
/A
C C)I'1
C t li CAS
Tile Material:
❑ Clay
e Concrete
❑ Other:
Product Control Approval Number: p 1 4- ' 1 227. 19
Check one of the following which apply to the proposed tile
securement for use with the proposed tile system assembly:
Mortar or Adhesive Set Tile Systems
Page - 2
(9' Mortar:
❑ Adhesive:
O Other: Type:
Length:
51 N/A
Underlavment:
Length:
Manufacturer:
Mixing Ratio:
Type:
Manufacturer:
Process No.
Tile Fasteners (for first three courses if roof pitch exceeds 5 ":12"
and is less than or equal to 7 ":12 "):
Check one of the following which apply to the proposed tile
fasteners (for the first three courses) for use with the proposed tile
system assembly:
❑ Minimum 12 ga. galvanized roofing nail:
Note: All tiles shall be installed in compliance with the provisions set
forth in the tile system assembly manufacturer's Product Control
Approval and the minimum requirements set forth in Subsections
3403.5(c) and 3404.2 of the South Florida Building Code. Tile
fasteners in the first three courses (if applicible) shall be of
sufficient length to penetrate the sheathing a minimum of 1" or
through the sheathing thickness a minimum of / whichever is
less.
The following information is required to confirm compliance with
Section 3403.5(b) of the South Florida Building Code.
Job Address: Contractor:
Underlavment (continued):
Check all of the following which apply to the proposed underlayment
for use with the proposed tile system assembly:
NJ ASTM #30 asphalt saturated felt with:
Manufacturer:
❑ ASTM #15 asphalt saturated felt with:
Manufacturer:
i
Mineral Surfaced Roll Roofing with:
Manufacturer: (44/v4"" C P94
❑ Other:
Type:
Manufacturer:
Underlavment Fasteners (if applicable):
Check one of the following which
underla ent attachment:
❑ Other:
Type:
Length:
Manufacturer:
Y2ZC
Minimum 12 ga. electro- galvanized
minimum 32 ga. x 1' /a' tin cap:
Length:
Manufacturer: (
O 19" overlap
❑ 6" overlap
l/ 4" overlap
O 19" overlap
O 6" overlap
❑ 4" overlap
❑ 19" overlap
" overlap
overlap
apply to the proposed
roofing nail with
Mortar or Adhesive Set Tile Systems
Page - 3
Spacing (per tile system assembly Product Control Approval):
Field: 1 Z " o.c.
Laps: (p " o.c.
5. Related Accessories:
Edge Metal (refer to Section 3408.2 of the South Florida Building
Code):
Type:
Dimensions:
Gauge or Thickness:
Finish:
Note: All edge metal shall be nailed on the flange and nailed or clipped
at the face in compliance with the provisions set forth in Dade
County Protocol PA 111, marked Appendix 'U' in the South
Florida Building Code.
Adhesives (check one of the following):
❑ Cold Adhesive:
Type:
Manufacturer:
fe( Flashing Cement:
2 ,,
Process No.
CAtvwizti� fz
2Co ‘A Cc
Type: 1/ ) d (1 �T
Manufacturer:
Job Address: Contractor: Process No.
Adhesives (continued):
Note: Application of adhesives shall be in compliance with the Roofing
Component Product Control Approval and the minimum
requirements set forth in Subsection 3403.5(e)(4)(cc) of the South
Florida Building Code.
Ventilation System (check one or more of the following):
The following information is required to confirm compliance with
Subsection 3401.4(e) of the South Florida Building Code.
0 Ridge: Type
1,
Soffit: Type
Size in'
Size
Note: If underlayment is comprised of a self - adhered membrane, both soffit
and ridge ventilation systems are required, unless a base sheet is
applied as an anchor sheet below the self - adhered underlayment.
Note: The Tile System Assembly shall be installed in strict compliance
with the application instructions enumerated in the Product
Control Approval. A permit shall be issued for application of the
specified Tile System Assembly only. Any change to the specified
Tile System Assembly shall require submission of a revised
SECTION II with a copy of SECTION I, noting the permit
number issued.
Mortar or Adhesive Set Tile Systems
Page - 4
Additional Notes:
•
Job Address:
Contractor:
DETAIL 111
Job Site Identification:
Mortar or Adhesive Set Tile Systems
Page - 5
Process No.
Roof Pitch
Ridge Venting:
( tfapplicable )
A
Dcck:
Type: r ni44.7 LI i v
Thickness:
Underlayment: 3D IS •
Underlacn
F ti F. suirot i2 44 ci
/--
1/4
3 4 " A
12"
FILL IN APPLICABLE ROOFING COMPONENTS WI IICH MAKE UP
TILE SYSTEM ASSEMBLY. INSERT ANY ADDITIONAL LEADERS
INDICATING ADDITIONAL ROOFING COMPONENTS NOT SHOWN
ON THIS PAGE. (Where Roofing Componcnt not uscd in Tile Systcm
Assembly, fill in with "N/A". )
Head Lap Dimension: 3 "
(minimum Y unless otherwise specified
in the tile system assembly Prochict Control
ApprowtO
Mortar/Adhesive: LIC (14.1A
Tile: C 0 fr14 C-40-51
e0,---x
Tile Fastener: oi j/A
Edge Metal of Gutter
Fastener: VIA flit
Bird Stop:
( if applicable )
Edge Metal
or Gutter:
N /A
Existing or Proposed
Soffit Venting:
/4
Job Address:
Contractor:
Ridge Height: Eave Height: Roof Mean Hcight
feet d < feet ( t "c feet
Insert Building Ridge Height, Eave Height and Roof Mean Height.
Also insert applicable information pertaining to the building below.
( See ASCE 7 -88 Fact Sheet Attached )
Exposure Category:
Classification Category:
At Hurricance Oceanline7: Y 1/N
Basic Wind Speed at
Building Location 110 mph
Building Condition based on
% of openings:
(See Table 9 ofASCE 7 -88)
Ground Level
BUILDING INFORMATION #1
Job Site Identification:
Mortar or Adhesive Set Tile Systems
Page - 6
Process No.
Job Address:
Contractor:
Qr
F= Ices
•
I_.
Sketch Roof Plan, indicating all dimensions, slopes and any roof top equipment.
Also insert variable labeled "a" which represents perimeter and corner dimensions
per Chapter 23 of the South Florida Building Code.
(See ASCE 7 -88 Fact Sheet Attached )
BUILDING INFORMATION #2: Roof Plan with Perimeter and Corner Dimensions
Job Site Identification:
Mortar or Adhesive Set Tile Systems
Page - 7
Process No.
Job Address: Contractor: Process No.
The undersigned certifies that the Mortar or Adhesive Set Tile System
Assembly is in compliance with the plans, specifications, and details
submitted by the architect.
STATE OF FLORIDA - COUNTY OF DADE rr // /
Before me this day personally appeared J ((L n 6 U4vL6
who, being first duly sworn, deposes and says that all information submitted
herein is true and correct.
19
My commission expires:
Licensed Contractor / Own&
Signature
o and subscribed before me this day of
Notary Public
State of Florida
Mortar or Adhesive Set Tile Systems
Page - 8
Coma Cast Corporation
4383 Southwest 70th Court _
Miami, Florida 33155
WILDING CODE COMPLIANCE DEPARTMENT
SUITE 1603
METRO-DADE FLAMER BUILDING
140 WEST FLAOLER STREET
MIAMI, FLORIDA 33130 -1503
(306) 376.2001
pRODUCT CONTROL NOTICE OF ACCEPTANCE Fax (305) 376.2006
Your application for Product Approval of Coma Cast Corporation. Mortar or Adhesive Set. Concrete
"Comatilc® Barrel" RoofirT Tile under Chapter 8 of the Metropolitan Dadc County Code governing the use of
Alternate Materials and Types of Construction, and completely described in the plans, specifications and
calculations as submitted by Redland Technologies, The Center for Applied Engineering, Inc., and Testwell
Craig Laboratories & Consultants, Inc. has been recommended for acceptance by the Building Code Compliance
Department to be used in Dade County, Florida under the specific and standard conditions set forth herein.
The approval shall be valid for a period of three years. The Building Code Compliance Department reserves the
right to secure a product or material at any time for a jobsite or manufacturer plant for quality control testing. If
product or material fail to perform in the approved manner, the Code Compliance Department may revoke, modify
or suspend the use of such product or material immediately. The Building Codc Compliance Department reserves
the right to require testing of this product or material should any amendments to the South Florida Building Code be
enacted affecting this product or material.
The expense of such testing will be incurred by the Manufacturer.
PRODUCT NO. :
ACCEPTANCE NO.: 94- 1222.19
EXPIRES: DEC 2 7 1997
APPROVED:
GEC 27 1994
METflOPOLITAN DADE COUNTY, FLORIDA
MEMO-DADE FLAGLER BUILDING.
Raul Rodriguez
Product Control Division
Supervisor
- PLEASE NOTE -
THIS IS TIIE COVERSIIEET. SEE ADDITIONAL PAGES FOR SPECIFIC AND GENERAL
CONDITIONS.
BUILDING CODE COMMITTEE
This application for Product Approval has been reviewed by the Metropolitan Dade County Building Code
Compliance Department and approved by the Building Code Committee to be used in Dade County, Florida under
the conditions set forth above.
Charles Danger, P.E., Director
Building Code Compliance Department
Metropolitan Dade County
Applicant:
Coma Cast Corporation
4383 Southwest 70th Court
Miami, FL 33155
Category: _ Prepared Roofing
.Sub Category: T il e
Type: Mortar Set/Adhesive Set
Sub -Type: Concrete
PRODUCT CONTROL NOTICE OF ACCEPTANCE
ROOFING SYSTEM APPROVAL
System Description
Coma Cast Corporation, located in Miami, Florida, is a manufacturer of cement roof tile for
mortar or adhesive set applications. This Product Control Approval relates to Coma Cast's "Comatile®
Barrel" tile profile. Refer to appropriate Product Control Approvals for other tile profiles.
All profiles have matching trim pieces used for rake hip, ridge hip, and valley terminations and
arc available in a smooth or broomswept surface texture. These accessories are manufactured for all
profiles and form a part of this Product Control Approval.
Coma Cast's "Comatile® Barrel" roof tile has been tested in compliance with the South Florida
Building Code requirements for concrete, mortar or adhesive set tile applications. The minimum roof
slope for Coma Cast's "Comatile® Barrel" mortar or adhesive set tiles shall be 2 ":12 ". See the "Profile
Drawing" section in this approval for the "Comatile® Barrel" profile drawing. The Coma Cast
"Comatile® Barrel" tile profile has been tested for both wind characteristics and static uplift
performance, therefore, any consideration for installation shall be done as a 'Moment Based System'.
Data for attachment calculations is noted in Tables 1 through 3 of this approval.
Contact:
Mike Arronte
President
Coma Cast Corporation
4383 Southwest 70th Court
Miami, FL 33155
(305) 665 -3664
1
Product Control No.: 94- 1222.19
Approval Date: i
Expiration Date: DEC 2 7 1997
Raul Rodriguez
TRADE NAMES OF PRODUCTS MANUFACTURED OR
LABELED BY APPLICANT
2
aul Rodriguez
Product Control No.: 94- 1222.19
Test Product
Product pimensions Specifications pescription
Comatile® Barrel 1= 16" PA 112 High profile, two - piece, extruded
Tile cap w = 9" concrete roof tile. For mortar set or
pan w = 8V2" adhesive set applications.
varying thickness
Trim Pieces — 1= varies PA 112 Accessory trim, concrete roof pieces
w = varies for use at hips, rakes, ridges and valley
varying thickness terminations. Manufactured for each
tile profile.
product
#30 Felt
#43 Coated Base
Sheet
Mineral Surface Cap
Sheet
Rainproof II
Ice and Water Shield
Mopping Asphalt
Flashing Cement
TRADE NAMES OF PRODUCTS MANUFACTURED OTHERS
Dimcnsiona
N/A
N/A
N/A
Lenzingtex -ZB 140 59" x 164' roll
Underlayment 22 Ibs/roll
30" x 75' roll
36" x 75' roll
or
60" x 75' roll
36" x 75' roll
N/A
N/A
Test
Specifications
ASTM D 226
type II
ASTM D 2626
ASTM D 249
PA 104
PA 104
PA 103
ASTM D 312
type III or IV
ASTM D 4586
Product Control No.: 94- 1222.19
Prod uct
Description
Saturated organic felt
to be used as a nailed
anchor sheet.
Saturated and coated
organic base sheet for
single or double ply
underlayment.
Mineral surfaced
asphalt roll roofing
for use as a top ply in
a double ply
underlayment system.
Single ply, nail -on
underlayment.
Single ply, nail -on
underlayment with 2"
self - adhering top
edge.
Self- adhering
underlayment for use
as a top ply in a two
ply underlayment
system with approved
#30 or #43 as the base
layer.
Asphalt for bonding a
mineral surface cap to
a mech. attached base
sheet in a double ply
underlaymcnt system.
Cut back, asphalt
based, asbestos free,
fiber reinforced,
trowel grade cement
for repair and flashing
applications.
Manufacturer
generic
generic
generic
Lenzing
Performance, Inc.
PCA #94- 0527.05
Protect -O -Wrap, Inc.
PCA #94- 0714.01
W.R. Grace Co.
PCA #92- 1116.01
generic
generic
Product
Asphalt Primer
Roofing Nails
Tin Caps
Tile Nails
Roof Tile Mortar
( "TileTiteT "' ")
Roof Tile Adhesive
(Polypro® AH160)
Valley Flashing
Drip Edge
Dimensions
N/A
min. 12 ga. with
'/," head
min. 32 ga.
min. 1 o.d.
max. 2" o.d.
min. 8d x 2% :" or
min. 10dx3"
N/A
N/A
min. 26 ga.
min. 16" width
min. 26 ga.
min. 2" face flange
min. 2" deck flange
Test
Specifications
ASTM D 41
PA 114
Appendix E
PA 114
Appendix E
PA 114
Appendix E
PA 123
PA 110
ASTM A 525
PA 111
Raul Rodriguez
Product Control No.: 94- 1222.19
Product
Description
Cut back, asphalt
based coating used to
facilitate bonding of
dissimilar materials.
Annular ring shank,
hot dipped, electro or
mechanically galv.
roofing nails for use
in underlayment
attachment.
Corrosion resistant
circular disc for use in
underlayment
attachment
Corrosion resistant,
screw or smooth
shank nails for
additional attachment
of tile at eave tile
courses.
Prepared mortar mix
designed for mortar
set roof tile
applications.
Adhesive designed
for use in roof tile
applications.
Galvanized steel
valley flashing
Galvanized steel drip
edge
Manufacturer
generic
generic
generic
generic
Bermuda Roof
Company, Inc.
PCA 1194- 0614.01
Polyfoam Products,
Inc.
PCA# 94- 0401.01
generic
generic
Test Agency Test Identifier Test Name /Report pats
The Center for Applied 94 -084 Static Uplift Testing May 1994
Engineering, Inc. PA 101
(Mortar Set)
The Center for Applied 94 -083 Static Uplift Testing April, 1994
Engineering, Inc. PA 101
(Adhesive Set)
TEST REPORTS
Redland Technologies P0647 -01 Wind Tunnel Testing July 1994
PA 108
(Mortar Set)
Testwell Craig Laboratories Lab #: YF -2 & 3 Physical Properties July, 1994
& Consultants, Inc. Tech: G. Suarez PA 112
5
Raul Rodriguez
Product Control No.: 94- 1222.19
SYSTEMS
Product Control No.: 94- 1222.19
Deck Type: Wood, Non - insulated
Deck Description: New construction ' or greater plywood or wood plank.
SYSTEM D: Mortar or Adhesive Set Application
Slope Range: 2 ":12" to 7 ":12"
Note: System D is only acceptable in this slope range.
Underlayment: Install choice of approved underlayment system, noted on Page 1 of Dade
County Protocol PA 120, in compliance with Section 3.02 of PA 120. See
System Limitation #6.
Roofing Tile:
Install tile in compliance with PA 120 using one of the approved mortars or
adhesives noted in this approval. Mortar or adhesive shall be applied in
compliance with the mortar manufacturer's Roofing Component Product
Control Approval. The mortar or adhesive attachment shall provide sufficient
attachment resistance expressed as a moment to meet or exceed the required
moment of resistance determined in compliance with PA 115 or PA 127. The
mortar and adhesive attachment data is noted in Table 3, attached.
Comments: 1. For re -roof applications, ' /, plywood is an acceptable substrate.
2. For mortar set applications, the first three courses of tile shall be nailed with
not less than one nail per tile. As an alternate, the first three courses of tile
shall be applied in mortar over a single layer of minimum 12 ga. wire mesh
with square openings of not less than 3 / 8 " which is mechanically attached to the
deck with not less than one roofing nail every 1 ft For roof pitches from
6 ":12" to 7 ":12 ", every third tile of every fifth course, beginning at the eighth
course, shall be nailed with not less than one nail per tile.
6
Raul Rodriguez
SYSTEM LIMITATIONS
1. The standard minimum roof pitch for Coma Cast "Comatile® Barrel" mortar set or adhesive set
tile applications is 2" rise in 12" run (2 ":12 "). The maximum roof pitch for mortar set or adhesive
set tile applications is 7" rise in 12" run (7 ":12 ").
2. Coma Cast's "Comatile® Barrel" tile profile has not been tested for nail -on applications,
therefore, System A (Counter- Batten Nail -On Application), System B (Direct Deck Nail -On
Application) and System C (Horizontal Batten Nail -On Application) do not form part of this
approval.
3. System installation shall be in compliance with the system specifications outlined in this Product
Control Approval. Mortar set or adhesive set tile shall be attached using an approved mortar or
tile adhesive noted in this approval, the data of which is noted in Table 3 of this Approval. The
method of attachment utilized shall provide sufficient attachment resistance expressed as a moment
to meet or exceed the required moment of resistance determined in compliance with Dade County
Protocol PA 115 or PA 127.
4. For mortar set applications, the first three courses of tile shall be nailed with not less than one nail
per tile. As an alternate, the first three courses of tile shall be applied in mortar or adhesive over a
single layer of minimum 12 ga. wire mesh with square openings of not less than ' / which is
mechanically attached to the deck with not less than one roofing nail every 1 ft For roof pitches
from 6 ":12" to 7 ":12 ", every third tile of every fifth course, beginning at the eighth course, shall be
nailed with not less than one nail per tile.
5. For mortar set or adhesive set tile applications, a field static uplift test by a Dade County
accredited testing agency, in compliance with Dade County Protocol PA 106, shall be required not
less than 30 days after application to confirm tile adhesion. The results of this testing shall be
reported to the Building Official and the installer stating that the application has passed or failed PA
106 testing. If the application fails PA 106 testing, the report shall state which portion of the test
was failed; Category I (examination for loose tile) or Category 2 (uplift testing of tile). Subsequent
to testing, the installer may repair not more than 5% of field area tiles and 10% of perimeter area
(i.e. ridge /rake) tile with approved tile adhesive. The installer shall place an identifiable marking on
each repaired tile for future reference. Any PA 106 re -test shall not include any marked tile.
6. For mortar or adhesive set tile applications, 30/90 hot mopped underlayment applications may be
installed perpendicular to the roof pitch prior to June 1, 1995 unless stated otherwise by the material
manufacturer. Thereafter, 30/90 underlayment systems shall be installed parallel to the roof pitch in
compliance with Appendix 'A' of Dade County Protocol PA 120.
7. All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo for
identification in the field.
8. The Coma Cast "Comatile® Barrel" tile profile has been tested for both wind characteristics and
static uplift performance, therefore, attachment calculations for installation in compliance with
Dade County Protocol PA 115 or PA 127 shall be done as a 'Moment Based System'
i
7
Raul Rodriguez
Product Control No.: 94- 1222.19
SYSTEM LIMITATIONS
(CONTINUED)
9. Applications for roofing permits shall include a completed Section II of the Uniform Building
Permit, a copy of Coma Cast Roof Tile's current specifications and details, a copy of this Product
Control Approval and a copy of the Product Control Approval of any Roofing Component used in
the proposed tile application. Reference shall be made to appropriate data for the required fire
rating.
10. The applicant shall retain the services of a Dade County certified testing laboratory to maintain
quality control in compliance with the South Florida Building Code and related protocols. Samples
taken shall be in compliance with Dade County Protocol PA 112, Appendix 'A'.
11. Any amendments to these provisions shall be in compliance with Sections 203 and 204 of the South
Florida Building Code.
8
Raul Rodriguez
Product Control No.: 94- 1222.19
Table 4: Attachment Resistance Expressed as a Moment - Mf (ft-Ibf)
from PA 101 Testing
Tile
Profile
Tile
Application
Attachment
Resistance
Comatile® Barrel Tile
Mortar Set
24.50
Adhesive Set
66.50
Table 2: Restoring Moments due to Gravity - M (ft -Ibf)
from PA 101 Testing
Tile
Profile
3 ":12"
4 ":12"
5 ":12"
6 ":12"
7 ":12" or
greater
Comatile®
Barrel Tile
5.19
5.11
5.00
4.88
N/A
DATA FOR ATTACHMENT
CALCULATIONS
9
Raul Rodriguez
Product Control No.: 94- 1222.19
Table 1: Aerodynamic Multipliers - X (ft
from PA 108 Testing
Tile
Profile
_
X (ft
Batten Application
X (ft
Direct Deck Application
Comatile® Barrel Tile
N/A
0.31
DATA FOR ATTACHMENT
CALCULATIONS
9
Raul Rodriguez
Product Control No.: 94- 1222.19
PROFILE DRAWING
Product Control No.: 94- 1222.19
l
>I I<
5/0"
Thickness
Crown Height Bottom
2 3/4"
111"Ov.r.11 Length
c+ I
I 4: 11..,
Width
- 1 "
ENO VIEW
COMER Cast Corp.
Width
f er -►
2 3/4"
c:2\
z.... CONCRETE BARREL TILE
COVER
��.
i
•
Width
4.— sr
CONCRETE BARREL TILE
PAN
A
TOP VIEW
Width
i g " Overall
Length
Crown H•Ight Top
1 3/4"
Crown Height Bottom
1 3/4"
COMATILE® BARREL TILE
Raul Rodriguez
NOTICE OF ACCEPTANCE: STANDARD CONDITIONS
This approval supersedes all previous approvals.
METROPOLITAN DADE COUNTY, FLORIDA
METRO-DADE FLAGLER BUILDING.
WILDING CODE COMPLIANCE DEPARTMENT
SUITE 1603
METRO-DADE FLAMER BUILDING
140 WEST FLAOLER STREET
MIAMI, FLORIDA 33130 -1563
• (306) 376.2001
FAX (305) 376 -2000
1. Extensions of Acceptance may be considered after a new application has been filed and the supporting
data, test reports no older than ten (10) years, have been re- evaluated.
All reports of re- testing shall bear the seal, signature and date of an engineer registered in the State of
Florida.
2. Any revision or change in the materials, use, or manufacture of the product or process shall automatically
be cause for termination, unless prior approval is granted for revisions or change.
3. Any unsatisfactory performance of this product or process or a change in Code provisions shall be grounds
for re-evaluation.
4.. This acceptance shall not be used as an endorsement of any product for sales or advertising purposes.
5. The Notice of Acceptance number preceded by the words Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the Notice of Acceptance is
displayed, then it shall be done in its entirety.
6. Product approval drawings, where required for permit applications, shall be provided to the applicant by
the manufacturer or his distributors unless otherwise noted in the Notice of Acceptance. The prints need
not be re- sealed by an engineer.
7. Failure to comply with the Standard Conditions shall be cause for termination of the Approval.
Raul Rodriguez
iroduct Control Division
Supervisor