ROOFINGBUILDING INSPECTION DEP? NRTMENT
APPLICATION FOR BUILC'ING PERMIT
Application is hereby made for the approval of the detailed statement of the , ?lans and specifications herewith submitted for the build-
ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami
Shores Village, Florida, and all provisions of the Laws of the State of Florida, 11 ordinances of Miami Shores Village and all rules and
regulations of the Building Division of Miami Shores Village shall be complied ` ,ith, whether herein specified or not. A copy of approved
plans and specifications must be kept at building during progress of the work.
Owner's Name and Address
Registered Architect and /or Engineer
Name and address of licensed contractor
Maximum live load to be borne by each floor
STATE OF FLORIDA,
COUNTY OF DADE. SS.
Chairman ____
Member
Member ___
MIAMI SHORES VILLAGE
•
Location and legal description of lot to be built on:
Lot Block Subdivision
No Street — -- - - - - - - - - - - -
4
Street and Number where work is to be done ___ _ ___ —'_ _a
State work to be done and purpose of building (by floors)______________________
To be constructed of Kind of foundation Roof Covering
Estimated Total cost of improvements $__L >_ # Amount o Permit $ e%�
Zone cubage required _ _____Plan Cub. ge
Distance to next nearest building _ __________Size of B ;'lding Lot
I hereby submit all the plans and specifications for said building. All notic s with reference to the building and its construction may
be sent to
The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer
of labor under the Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement,
and has complied with the provisions thereof, and will require similar compliance from all contractors or sub - contractors employed by him
in the work to be performed under this permit; and will post or cause to be p r sted for inspection on the site of the work such public notice
or notices as are required by the Act. The undersigned agrees to employ only ':uch subcontractors, on work to be performed under this
permit, as are licensed by Miami Shores Village.
Remarks (Signed)__=--- • `3 _ J
Date / " it
1:4
C
' I — _r r and for no other purpose.
New Building Remodeling Addition Repairs No. of Stories
•
Before me, the undersigned authority, a notary public, duly authorized to ac,_ninister oaths and take acknowledgments, personally ap-
peared
--- ------------ - - - - -- to me well known,
al d who, being by me first duly sworn, upon oath deposes and says that he is the
of ,he above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts
Li ,„:n by 'aim stated are true.
Permit N Date Read, Sworn to and Subscribed before me.
Disapprov °d Date
(Signed). Building Inspector My Commission Expires
-------------- ---
Notary Public, State of Florida
PLANNING BOARD DATE
Member
Member
Member
Council Approved Date Disapproved Date
NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval has been obtained from
the Planning Board.
A re- inspection fee of $1.00 will be charged when such re- inspection i; made necessary by improper notice for inspection or faulty
materials and /or workmanship.
,19 S 3
BUILDING ❑ DATE 195
ELECTRICAL ❑ PERMIT N° 14 213 Contractor's
PLUMBING ❑ License No
ROOFING d Work to be performed under this Permit
Owner of
Building
Architect
Contractor
or Builder
Legal
Description
Address of
Building
Lot
CONTRACTOR OR BUILDER
MIAMI SHORES VILLAGE, FLORIDA
Subdi-
vision
Value of
Project $ j
Amt. of
Permit $
This permit is granted to the contractor or builder named above to construct the building or to install the equipment or device described in the application
herefor in strict compliance with all ordinances pertaining thereto and with the understanding that the work will be performed in compliance with any plans,
drawings, statements or specifications that may have been submitted to and approved by the proper municipal authorities. This Permit may be revoked at any
time if the work is not done in compliance with such ordinances or if the plans are changed without authorization. A further condition upon which this permit is
granted is the understanding that the contractor or builder named above assumes the responsibility for a thorough knowledge of the ordinances and regulations
pertaining to the work covered hereby whether shown on the plans or drawings or in the statements or specifications and that he assumes responsibility for work
done by his agents, servants or employees.
Signed • BY
INSPECTOR
In consideration of the issuance to me of this permit I agree to perform the work covered hereunder in compliance with all ordinances and regulations
pertaining thereto and in strict conformity with the plans, drawings, statements or specifications submitted to the proper authorities of Miami Shores Village.
In accepting this permit I assume responsibility for all work done by either, myself, my agent, servant or employee.
BY AUTHORITY
Date/
APPROVED:
Zoning
Mechanical
FEES: PERMIT C)
PERMIT APPLICATION FOR MIAMI SHORES VILLAGE
Job Address / 23 0 0. J Y Sr: Tax Folio /1 , ZC 601 ¢ 0 230
Legal DescriptionSec 03 /0 - 104 (0+11 81t 8 S'Historically Designated: Yes No
Owner/Lessee / Tenant R 0 S 4 Z i 0 PO ■.-S
Owner's Address / 2 3 O N •' Ps .S ll
Contracting Co. 1 v4 ° eci ✓ti /
Qualifier '
State # CC C O5 6 8 (7 Municipal # Competency # Ins. Co.
Architect/Engineer Address
Bonding Company Address
Mortgagor Address
Permit Type (circle one): BUILDING ELECTRICAL PLUMBING MECHANICAL ROOFING PAVING FENCE SIGN
WORK DESCRIPTION — w e ct+ v KA os 0 I t v:(
�
Square Ft. 500 Estimated Cost (value) ®( �
WARNING TO OWNER: YOU MUST RECORD A NOTICE OF COMMENCEMENT AND YOUR FAILURE TO DO SO MAY RESULT IN YOUR'
PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY (W YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER
OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT.)
Application is hereby made to obtain a permit to do work and installation as indicated above, and on the attached addendum (if applicable). I certify that all work
will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that separate permits are required for ELECTRICAL
PLUMBING, SIGNS, POOLS, ROOFING and MECHANICAL WORK.
OWNERS AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating
construction and zoning. Furthermore, I authorize the above -named contractor to do the work stated.
i =nature of owner and/or Condo President Date Signature of Contractor or Owner - Builder Date
Notary as to Owner and/or Condo President Date Notary as to Contractor or Owner- Builder Date
My Commission Expires:
RADON
Building
C.C.F. , ° Lib' NOTARY 9 C ) BOND 306
My Commission Expires:
Electrical
Master Permit # 4 45
Phone
I ti C Address PO • (0)4
Phone 4- ®7 i 5 6 6
TOTAL DUE
Plumbing Structural Engineer
. PERMIT APPLICATION FOR MUNICIPALITIES OF DA *E COUNTY
Date ?'- 2 "i Job Address /Z. k � fc �T
Legal Description& 3 4/6-37 407 /13 fI P 6./4 85' Master Permit #
Owner s Sa 1',b j/E9, C Tenant
Owner's Address /73U ,a A/E 7 Day -Time Phone
Contracting Co Z5e rr�� 2AJ
C
Qualifier tom-
Address Pitgoi< f-44i+Il„
State# 1, GC. O r 6 At Competency# Ins. Co.
�A4 .ess.
B s —
Martg agor - Aidraa_
Permit Type: /ROOFING BUILDING ELECTRICAL PLUMBING MECHANICAL PAVING FENCE SIGN
Application is hereby made for a permit to do work & installation as indicated. $ understand tha
separate permits are re uire Electrical, Plumbing, Sig:is, Pools, Roofing, & Mechanical work.
WORK DESCRIPTION %G ,4464
Square Ft. egOd
WARNING TO OWNER: YOU MUST RECORD A NOTICE OF COMMENCEMENT AND YOUR FAILURE TO DO SO MAY RESUL
IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING
CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING THZ NOTICE. A BACKFLOW PREVENTION DEVIC
PERMIT AND CERTIFICATION TEST MAY BE REQUIRED IN ACCORDANC' WITH ORDINANCE #825. CALL THE PUBLI
WORKS DEPT. AT 787 -1001 OR VISIT THEIR OFFICE AT 1815 N.E. 150 ST.
OMER'S AFFIDAVIT: 1 certlfy that all the foregoing Information Is accurate, and that all work will be done In compllance with al
applicable laws regulating construction and zoning. Furthermore, I authorize the above -named contractor to do the work stated.
Signature of Property Owner or Condo Pres.
ADMINISTERED OATH ❑
SWORN TO & SUBSCRIB D BEFORE ME THIS
Y OF .if , 19/
1 04
Sig •' re of NOTARY ident
!■ ` ' � 7 Lam. 1
(Print, Type, or Stamp Commissioned Name)
Personally Known ❑ or Produced I.D
Type of I.D. produced 0 I- -
Zonin
Mechanical
FEE
Building
Phone 7?“
Plumbing
Estimated Cos
(Print,
Tax Folio l! 3 a/41110S °
ADMINISTERED OATH ❑
sypAy TO & SUBSC$IB D BEFORE ME TS
DAY OF .J 1 , 19 .
6 Altr t W"f • ;.a; act
FYpe; ter Stamp ommissioned Name)
Personally Known ❑ or Produced I.D.
Type of I.D. produced
Electrical
Engineering
NOTICE OF COMMENCEMENT
• A RECORDED COPY MUST BE POSTED ON THE JOB SITE AT TIME OF FIRST INSPECTION
PERMIT NO. TAX FOLIO NO. //320 Co /` 4"0 8
STATE OF FLORIDA:
COUNTY OF DADE:
THE UNDERSIGNED hereby gives notice that improvements will be made to certain real property, and in accordance with
Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement.
1. Legal description of property and street address: 6- e-d'• 3 P.8 /D - 3 7 Z0 /4r• // /3 /4. 86
/23o /fig 1 /eez
2. Description of improvement: ( — V oo -r
3. Owner(s) name and address:.�P�7V %/t n l7SQ/ / 61 2)44
Interest in property:
Name and address of fee simple titleholder:
4. Contractor's name and address: /ykv - Co v.i Rce—vg
/4e_.
d. /3. ,c 6 y0 / : A t i 3.??� c
� FLORIDA, COUN DAD L:
4 . Surety:(Payment bond required by owner from contractor tfany) r ;,,�ca
Name and address:
Amount of bond $
(Lender's name and address:
Persons within the State of Florida designated by Owner upon whom notices or other documents may • • served as provided
by Section 713.13(1)(a)7., Florida Statutes,
Name and address:
,In addition to himself, Owner designates the following person(s) to receive a copy of the Lienor's Notice as provided in
Section 713.13(1)(b), Florida Statutes.
Name and address:
%Expiration date of this Notice of Commencement: (the expiration date is 1 year from the date of recording unless a
different date is specified)
oe
Signature of Owner
Print Owners Name /e6" '9'4e,0 47. 26» 74 5
Sworn to and subscribed b re me this 24 day of Jd
Notary Public �� r
Print Notary's N e
My Commissi• Expires:
/2310 Ale 1S S6
•
�f /1/� A t�f� r ABA! PE Z
NC:4Vial A'yl PTF err r\' wr( T 1,
Cgi;iMESION t: 1. CCtS333::2
A 9y Cm 9 A'f^fi'WeA• m n r r . gIs,,n
99R402133 1999 AUG 03 11:38
f
Prepared by: E • o 'i
Address: FO, 13C a 57 13[se"
17'2 I1•.SA /MEW
APPENDIX "F"
REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIONS
As it pertains to this Appendix "F it is the responsibility ui U%C rooting contractor to provide tiro owner with the
required roofing permit, to provide the owner with this appendix and to explain to the owner the content of this
form. The provisions of Chapter 34 of the South Florida Building, Codc (SFBC) govern all the minimum
requirements and standards of the industry for roofing system installations. . Additionally. the following items
should be addressed as part of the agreement between the owner and the contractor. The owner's initial in the
adjacent box indicates that the item has been explained.
i d 1. Aesthetics - Workmanship: The %vorkmanship provisions of Chapter 34 are for tare: purpose of
providing that the roofing, system meets the wind resistance and water intrusion performance standards.
Aesthetics (appearance) issues are not a consideration with respect to workmanship provisions. Aesthetic issues
such as color or architectural appearance, that are not part of a - zoning code, should be addressed as part of the
agreement between the owner and the contractor.
'8 2. Renailing Wood D'cet s: When replacing roofing, the existing wood roof deck may have to be renailed •
in accordance with the current provisions of Chapter 29 oldie SFBC. (The roof deck is usually conce ted_prior to
remov the existing roof system)
/S 3. Common Roofs: Common roofs are those \vhich have no visible delineation between neighboring
X units (i.e. townhouses, condominiums, eta.). In buildings Nvith common roofs. the roofing contractor and /or
owner should notify the occupants of adjacent units of roofing work to be performed.
/(4.-0 4. Exposed ceilings: Exposed. open beam ceilings are where the underside of the roof decking can bc
‘'ietved from below. The owner may xvish to maintair, the architectural appearance. therefore, roofing nail
penetrations of the underside of the decking may not be acceptable. The SF BC provides the option of maintaining
this appearance.
,e4D 5. Pondin The current roof system and /or deck of the building may not drain well and may
e
cause water to pond (accumulate) in low -lying areas of the roof. Ponding can be an indication of structural
distress and may require the review of a prof_s ion: :l structural engineer. Ponding may shorter the life
expectancy and performance of the new roofing system. Pondinu conditions may not be evident until the orignr - QI
roofing system is removed. Ponding conditions should be corrected.
•
g /...D 6. Overflow Scuppers (wall outlets): It is required that rainwater flow off so that the roof is not
overloaded from a build up of water. Perimeter /edge %valls or other roof extensions may block this discharge if
overflow scuppers (wall outlets) are not provided. It may be necessary to install overflow scuppers in accordance
with Chapter 23 of the SFBC.
/ea 7. Vcntilntion: Most roof structures should have some ability to vent natural airflow through the interior
of the structural assembly (the building itself). The existing, amount of attic ventilation shall not bc reduced. It
may be beneficial to consider additional venting which can result in extcndino the service life cif the roof.
S. The owner may contact the \1iartti -Dade County Consumer Services Department for further
information regarding rant above.
4
Ovner'slAgent's Signature U.1te
' y
Su
c•rar c�r•crrr• __S� -t it• �Ci cI3.11 6_b_9��__ -_
Contractors Z ER- COUNTY ROOFING, INC. Job Address: / Zo 3 a Ai' E 9 S' sT.
ROOF CATEGORY
Ili (Low Slope Application) ❑ (Nail -On Tile) ❑ (Mortar- Adhesive Set Tile)
❑ (Asphalt/Fiberglass Shingles) ❑ ( Metal Roofs1Wood Shingles & Shakes) ❑ (Other)
ROOF TYPE
❑ New Roof te ❑ Recovering ❑ Repair ❑ Maintenance
Flat Roof Area (ft g6 e Sloped Roof Area (ft
Appendix "E"
UNIFORM ROOFING PERMIT APPLICATION
PROCESS No.
Exposure category (per ASCE 7 -88): Building Classification category (per ASCE 7 -88 table 1):
t ,
Ft.
123.01.78 9/96
p Z0 QF HEIGHT AND SYSTEM DETAILS v. 5 • X 44
7 r 6 141 wok W..&. (Draw details as needed) T •
Ms pa •
- ark► Cr 44/ l i l •
1 / - 014 ° / OE 6 CAF
(14-r a?op'PEQ.
Dec
type:
Fastener Type:
4 f"
Oyu; 00 d
ATTACHMENT
SPACING
M c p
Field: I Z. Perimeter: Corner: b
DETAIL 1 & 2
Page -1
Total (ft') 8 a
r
r
Master Permit No.
ROOF PLAN
4
PRODUCT CONTROL NOTICE OF ACCEPTANCE
GAF Materials Corporation
1361 Alps Road
Wayne, NJ 07470
Your application for Product Approval of:
GAF Ruberoid® Modifed Bitumen Roof Systems for Wood Decks
under Chapter 8 of the Metropolitan Dade County Code governing the use of Alternate Materials and Types of
Construction, and completely described in the plans, specifications and calculations as submitted by:
Dynatech Engineering, Inc., Factory Mutual Research Corporation, and Underwriters Laboratories, Inc.
has been recommended for acceptance by the Building Code Compliance Office to be used in Dade County, Florida
under the specific conditions set forth on pages 2 -60 and the standard conditions on page 61.
This approval shall not be valid after the expiration date stated below. The Building Code Compliance Office
reserves the right to secure this product or material at any time from a jobsite or manufacturer's plant for quality
control testing. If this product or material fails to perform in the approved manner, the Building Code Compliance
Office may revoke, modify, or suspend the use of such product or material immediately. The Building Code
Compliance Office reserves the right to revoke this approval, if it is determined by the Building Code Compliance
Office that this product or material fails to meet the requirements of the Building Code Compliance Office that this
product or material fails to meet the requirements of the South Florida Building Code.
The expense of such testing will be incurred by the manufacturer.
Acceptance No.: 97- 0804.14 Revises No.: 95- 1003.03
Expires: 11/06/00
Approved: 11/06/97
1
4 /
y
Raul Rodriguez
Product Control Supervisor
THIS IS THE COVERSHEET, SEE ADDITIONAL PAGES FOR SPECIFIC AND GENERAL,
CONDITIONS
BUILDING CODE COMMITTEE
This application for Product Approval has been reviewed by the Metropolitan Dade County Building Code
Compliance Office and approved by the Building Code Committee to be used ' n :de Cou
nty, Fl rid9 under the
conditions set forth above. tf / j , /. /. ,
• i•
Charles Danger, P.E.
Director
Building Code Compliance Dept.
Metropolitan Dade County
Applicant:
GAF Materials Corporation
1361 Alps Road
Wayne, NJ 07470
PRODUCT CONTROL NOTICE OF ACCEPTANCE
ROOFING SYSTEM APPROVAL
Category: Membrane Roofing System
Sub - Category: Built -up Roofing
Type: Modified Bitumen
Sub -Type: APP and SBS
Contact:
William J. Woodring
Director of Technical Services
(973) 628- 4134
Page 2 of 61
Product Control No: 97 0804.14
Product Control No.: 97- 0804.14
Approval Date: November 6, 1997
Expiration Date: November 6, 2000
System Description
GAF Materials Corporation has been manufacturing commercial roofing products for more than 100
years.
GAF produces a wide range of roof products for built -up roofing systems. The modified bitumen
products include both APP and SBS products in smooth, granule and fire rated versions. In addition,
GAF offers two ply modified systems to meet the specification requirements for multilayer SBS modified
specifications.
GAF products are distributed through a wide network of roofing wholesale distributors throughout the
South Florida area.
GAF provides warranted systems over various insulated and non - insulated substrates, copies of which
can be obtained from GAF and can be found in the Ruberoid Modified Bitumen Application and
Specification manual published annually.
GAF roof system assemblies have been extensively tested at Factory Mutual Research Corporation and
Underwriters Laboratories. GAF modified bitumen membranes have been tested in compliance with
ASTM D 5147 test requirements.
•
Frank Zuloaga,
Roofing Product Control Examiner
Insulation Types:
Material
Wood
Material
Wood
Basalt Wool
Perlite
Polyisocyanurate
Composite Board
Wood Fiberboard
High Density Wood Fiberboard
Rockwool
Maximum Design Pressure
Design Pressure
-75psf
Maximum Fire Classification
Classification
Class 'A'
Product Control No: 97 0804.14
Note: Fire classifications and maximum design pressures do not reference all assemblies over all deck
types. Review system listings for design pressures and the Underwriters Laboratories Roofing
Materials Directory for Fire Classifications.
Page 3 of 61
-- -
Frank Zuloaga,
Roofing Product Control Examiner
Product
GAF Asphalt
Concrete Primer
GAF Mineral Shield® 60 Ib. bags ASTM D 1863
Granules
GAF WeatherCoat®
Emulsion
GAF Premium
Fibered Aluminum
Roof Coating
GAF Jetblak All
Weather Plastic
Cement
5 gallons
1, 5 gallons
3 sq. roll
75 Ib. roll
GAFGLAS #80 2 Sq. Roll
Ultima"' Base Sheet 70 lbs. /roll
GAFGLAS Ply 6® 5 sq. roll
45 lb. roll
GAFGLAS Flex 5 sq. roll
PlyTm 6 45 Ib. roll
E GAFGLAS Ply 4® 5 sq. roll
GAFGLAS® 76 lb. roll
Mineral Surfaced
Cap Sheet
TRADE NAMES OF PRODUCTS MANUFACTURED OR
LABELED BY APPLICANT
Test
Dimensions Specification
5, 55 gallons ASTM D 41
ASTM 1227
1, 5 gallons ASTM D 2824
ASTM D 3019
ASTM D 3409
ASTM D 4601
ASTM D4601
ASTM D 2178
ASTM D 2178
ASTM D 2178
ASTM D 3909
Page 4 of 61
Product Control No: 97- 0804.14
Product
Description
Asphalt concrete primer used to promote
adhesion of asphalt in built -up roofing.
Granules for surfacing of exposed
asphalt, cold process cement or
emulsion. GAF Mineral Shield®
Granules shall be used for flashing
applications only. _
Surface coating for smooth surfaced
roofs.
Fibered aluminum coating.
Refined asphalt blended with a mineral
stabilizer and fibers. Permits adhesion
to wet and dry surfaces.
Asphalt impregnated and coated glass
mat base sheet.
Asphalt impregnated and coated,
fiberglass base sheet
Type VI asphalt impregnated glass felt
with asphalt coating.
Type VI asphalt impregnated glass felt
with asphalt coating.
Type IV asphalt impregnated glass felt
with asphalt coating.
Asphalt coated, glass fiber mat cap sheet
surfaced with mineral granules.
rank Zuloaga,
Roofing Product Control Examiner
Product Control No: 97. 0804.14
Test Product
Product Dimensions Specification Description
GAFTITE® Base PA 114 Base sheet fastening assembly.
Sheet
Fastener and Plate
Galvalume Plates 3" and 3 'A" PA 114 Round galvalume stress plates.
NTB Fasteners PA 114 Fastener for use in gypsum, tectum and
lightweight insulating concrete decks.
Polypropylene Plates 3" and 3 '''A" PA 114 Round polypropylene stress plates.
Ruberoid® 20 1.5 sq. roll ASTM D 5147 SBS modified asphalt base sheet and
interply sheet reinforce with a glass fiber
mat.
Ruberoid® Mop 1 sq. roll ASTM D 5147 Non -woven polyester mat coated with
Granule 103 lbs. polymer modified asphalt and surfaced
with mineral granules.
RUBEROID MOP 1 sq. roll ASTM D 5147 Non -woven polyester mat coated with
Smooth 87 lbs. polymer modified asphalt and smooth
surfaced.
RUBEROID MOP 1 sq. roll ASTM D 5147 Non -woven polyster mat coated with
PLUS 102 lbs. polymer modified asphalt and surfaced
with mineral granules.
RUBEROID MOP 1 sq. roll ASTM D 5147 Non -Woven polyester mat coated with
170FR 103 lbs. fire retardant polymer modified asphalt
and surfaced with mineral granules.
Smooth
RUBEROID TORCH 1 sq. roll
Granule 102 lbs.
1 sq. roll ASTM D 5147 Non -Woven polyester mat coated with
105 lbs. fire retardant polymer modified asphalt
and surfaced with mineral granules.
RUBEROID TORCH 1 sq. roll ASTM D 5147 Heavy duty, polyester reinforced,
87 lbs. asphalt modified bitumen membrane,
smooth surface.
ASTM D 5147 Heavy duty, polyester reinforced,
asphalt modified bitumen membrane,
granule surface.
Page 7 of 61
Frank Zuloaga,
Roofing Product Control Examiner
Product
Dekfast Lock Plate
Dekfast Fasteners
#15
Dekfast Fasteners
#12
ISO 95+ Composite
EPS
High Density Wood
Fiberboard
Pelite/Urethane
Composite
Perlite Insulation
Polyethylene
Red Rosin
Test
Dimensions Specification
3 "x31/4"
various
various
various
various
4 mil min.
various
Minimum #
12
Product
Description
PA 114 Polypropylene locking
plate.
PA 114 Insulation fasteners for
concrete decks
PA 114 Insulation fastener
and wood decks.
PA 110 Polyisocyanurate / perlite Firestone
ridged insulation (with current PCA)
ASTM D 312 Type III or IV Hot asphlat
bitumin adhesive
ASTM D 41 Asphalt Primer
PA 110 Extruded polystyrene
insulation
PA 110 Wood fiber insulation board
PA 110 Perlite / urethane composite
board insulation
PA 110 Perlite insulation board
Vapor barrier / Air barrier
Rosin paper for barrier
layer on wood decks
PA 114 Corrosion resistant annular
ring shank nails
Page 11 of 61
Product Control No: 97- 0804.14 .
Manufacturer
Construction
Fasteners Inc. •
(with current PCA)
Construction
Fasteners Inc.
(with current PCA)
for steel Construction
Fasteners Inc.
(with current PCA)
generic
generic
generic
generic
generic
generic
generic
generic
generic
Roofing Product Control Examiner
Test
Product Dimensions Specification
MB aluminum roof
coating
Dens -Deck
#12 Roofgrip
#14 Roofgrip
Gripdek Fastener
Hexcel Fastener
Hextra
Standard Plastic
Plate
ISO 95+
E'NRG'Y -2
ISORoc
Min. 32 ga. x
1
various
3" round
various
various
various
PA 121
PA 110
PA 114
PA 114
PA 114
PA 114
PA 114
PA 114
PA 110
PA 110
PA 110
Product
Description
Corrosion resistant circular
discs.
Aluminum roof coating
Gypsum insulation board.
Insulation fastener for steel
or wood decks
Insulation fastener steel,
wood or concrete decks
Insulation fastener
Insulation fastener
Insulation fastener and
metal or plastic plate
Polyolefin plastic plate
Polyisocyanurate foam
insulation
Polyisocyanurate foam
insulation
Polyisocyanurate foam /
rockwool composite
insulation
Page 12 of 61
Product Control No: 97- 0804.14
Manufacturer
generic
Grundy Industries
(with current PCA)
Georgia Pacific
(with current PCA)
ITW Buildex
(with current PCA)
1TW Buildex
(with current PCA)
1TW Buildex
(with current PCA)
ITW Buildex
(with current PCA)
ITW Buildex
(with current PCA)
1TW Buildex
(with current PCA)
International
Permalite
(with current PCA)
NRG Barriers, Inc.
(with current PCA)
NRG Barriers, Inc.
(with current PCA)
Frank Zuloaga,
Roofing Product Control Examiner
Membrane Type:
Deck Type 1:
Deck Description: 19 / 72 " or greater plywood or wood plank decks
System Type A(2):
Base Sheet:
Ply Sheet:
Membrane:
Surfacing:
Maximum Design
Pressure:
Maximum Fire
Classification:
Maximum Slope:
Specification No.:
SBS
Wood, Non - insulated New Construction or Reroof
Base sheet mechanically fastened.
All General and System Limitations shall apply.
AFGLAS® #75 GAFGLAS #80 Ultima"'' Base Sheet, GAFGLAS® PLY 4 ®,
GAFGLA Y 6 ®, GAFGLAS FlexPIyTM Base Sheet,GAFGLAS®
STRATAVENT® Nailable, RUBEROID Modified Base Sheet or RUBEROID®
20 applied to the deck with approved annular ring shank nails and minimum 1 s /
tin caps at a fastener spacing of 9" o.c. at the lap, 12" o.c. in two rows staggered
along the center line of the sheet in the field.
(Optional two, or three plie , GAFGLAS® PLY 6®
Ply or GA GLAS Flex Ply 6 sheet adhere ' in a u mopping of approved asphalt
applied within the EVT range and at a rate of 20-40 IbsJsq..
r more plies of RUBEROID MOP Smooth, Ruberoid® Mop 170 FR,
Ruberoid® Mop Granu • p Plus Granule, Ruberoid® 30 or
Ruberoid® 30 FR o uberoid® Mop F or RUBEROID UltraCladTM SBS in
adhered in a full mopping of approved asphalt applied within the EVT range and
at a rate of 20 Ibsisq..
Or,
One or more plies of RUBEROID MOP Smooth, RUBEROID® Mop Granule,
RUBEROID® Mop 170 FR, RUBEROID® Mop Plus Granule, RUBEROID® 30,
RUBEROID® 30 FR or RUBEROID® Mop FR or RUBEROID UItraCladTM SBS
in RUBEROID Modified Bitumen Adhesive at an application rate of 1 -2 gal. /sq.
Product Control No: 97- 0804.14
(Optional, required if RUBEROID MOP Smooth or RUBEROID 20 is top
membrane) Install one of the following:
I. Gravel or slag applied at 400 lb. /sq. and 300 Ibisq. respectively in a flood coat
of approved asphalt at 60 lb./sq..
2. GAFGLAS Mineral Surfaced Cap Sheet in an approved asphalt at an
application rate of 25 lbJsq. + 15 %.
-45 psf (See General Limitation #7)
'A'. See General Limitation #2.
2 ":12 "; See General Limitation #3.
Page 22 of 61
Frank Zuloaga,
Roofing Product Control Examiner
Wood Deck System Limitations:
4. '/2 Type X gypsum board is acceptable to be installed directly over the wood deck..
Page 57 of 61
Product Control No: 97- 0804.14
1. Fastener spacing for anchor sheet attachment is based on a Minimum Characteristic Force (F')
of 95 Ibf or greater as tested in compliance with Merto -Dade County Protocol PA 105. If F' as
tested is below 95 Ibf, a professional engineer may submit a revised fastener spacing utilizing
the withdrawal resistance value taken from Merto -Dade County Protocol PA 105 and
calculations in compliance with Metro -Dade Roofing Application Stanadrd PA 117.
2 All standard insulation panel sizes are acceptable for mechanical attachment. When panels are
applied in hot asphalt, maximum panel size shall be 4' x 4'.
a. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') of
275 Ibf. as tested in compliance with Merto -Dade County Protocol PA 105 & Roofing
Application Standard PA 117. If the fastener value, as field tested, are below 275•Ibf. insulation
attachment shall not be acceptable.
3 A slip sheet is required with GAFGLAS FlexPly 4® and Ply 6® when used as a mechanically
fastened base or anchor sheet.
Frank Zuloaga,
Roofing Product Control Examiner
GENERAL LIMITATIONS
Product Control No: 97- 0804.14 , •.
1 All asphalt shall comply with ASTM D 312 type III or type IV requirements, and
approved by applicant.
2 Fire ratings are determined by a combination of slope, deck type and assembly. Refer to
current Underwriters Roofing Materials Directory or other fire testing data listed in the
testing file. Fire ratings shall be in strict compliance with Sections 3401.5 and 3401.6 of
the South Florida Building Code.
3 Maximum slope range shall vary for each system; consult current Underwriters
Laboratories Roofing Materials Directory and manufacturer's specifications for
compliance with design criteria for each project.
4 An overlay and/or recovery board insulation panel is required on all applications over
closed cell foam insulations when the base sheet is fully mopped. If no recovery board is
used, install one layer of GAFGLASS STRATAVENT Perforated, laid dry.A base sheet
may be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.;
or strip mopped 8" ribbons in three rows, one at each sidelap and one down the center of
the sheet allowing a continuous area of ventilation. Encircling of the strips is not
acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation.
Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note:
Spot attached systems shall be limited to a maximum design pressure of -45 psf. Where
STRATAVENT Perforated is used over approved isocyanurate foam insulation, the
maximum design pressure is limited to — 60psf.
5 All work shall be performed by a contractor licensed to do roofing work in Metro -Dade
County. Contractor shall be familiar with the details and specifications published by the
manufacturer, and the requirements of the SFBC.
6 The submission of system specifications and details shall accompany the Section II
Building Code Permit. This information is available in the publications listed in the
'System Description' of this Product Control Approval. The submission of these
documents, as well as the proper application and installation of all materials shall be the
sole responsibility of the contractor.
Page 58 of 61
Zuloaga,
Roofing Product Control Examiner
Page 59 of 61
Product Control No: 970804.14
7 Perimeter and corner areas shall comply with the enhanced uplift pressure of these areas,
as calculated in compliance with Chapter 23 of the South Florida Building Code. Fastener
densities shall be increase for both insulation and base sheet as needed calculated in compliance
with Metro -Dade County Roofing Application Standard PA 117. (When this limitation is
specifically referred within this NOA, General Limitation #20 will not be applicable.)
8 All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination
designs shall conform with Metro - Dade County Roofing Application Standard PA 111
and the wind load requirements of Chapter. 23 of the South Florida Building Code.
9 Flashings shall be installed according to the manufacturers standard details, and may be
applied in cold application adhesive, approved asphalt or may be applied in conjunction
with an approved torch applied modified bitumen membrane. Specific details, approved
by the manufacturer, shall be submitted with the Section II Permit Application. All details
shall comply with the provision of the South Florida Building Code.
10 Fastener spacing for base sheet attachment is based on a Minimum Characteristic Force
(F') value as tested in compliance with Metro -Dade County Protocol PA 105. If the fastener
values as tested are below those listed in the System Limitations, a professional engineer may
submit a revised fastener spacing utilizing the withdrawal resistance value taken from a Metro -
Dade County Protocol PA 105 test report and calculations that comply with the wind load
requirements of Chapter 23 of the South Florida Building Code and Roofing Application Standard
PA 117.
11 Fastener spacing for insulation attachment is based on a Minimum Characteristic Force
(F') value of 275 lbf., as tested in compliance with PA 105. If the fastener value, as field tested,
are below 275 lbf. insulation attachment shall not be acceptable.
12 Asphalt moppings shall be with applied with approved asphalt and shall be in compliance
with equiviscous temperature (EVT) methods of asphalt determination. Asphalt containers or
bulk tickets shall indicate an EVT, finished blowing temperature (FBT) and flash point. Asphalt
types and temperature ranges shall be in compliance with Subsection 3403.4(a)(3) of the South
Florida Building Code.
13 Insulation may be installed in multiple layers. The first layer shall be attached in
compliance with Product Control Approval guidelines. All other layers shall be adhered
in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40
lbs. /sq., or mechanically attached using the fastening pattern of the top layer. Refer to
manufacturer's literature and/or the NRCA Roofing and Waterproofing Manual for correct
application procedures of insulation panels in approved asphalt or adhesive, which shall
comply with provision of Roofing Application Standard PA 117
Frank Zuloaga,
Roofing Product Control Ecaminer
Product Control No: 97- 0804.14 .
14 All standard panel sizes are acceptable for mechanical attachment. When applied in
approved asphalt, panel size shall be 4' x 4' maximum.
15 In re- covery/re- roofing applications, prior to the application, all existing roof surfaces used as a
bonding substrate shall be tested in compliance with Metro-Dade County Protocol PA 124 for
uplift resistance. Test pressures shall be calculated in compliance with the wind Toad
requirements of Chapter 23 of the South Florida Building Code to the design pressure of the roof.
16 In re- roofing applications, moisture content in an existing roof must be in compliance with
Section 3401.10(m), (n) of the South Florida Building Code.
17 Roll good materials shall be stored on end and on a clean, flat and dry surface.
18 If required, any Factory Mutual Approved vapor barrier in conjunction with proprietary or
approved adhesives may be used prior to the application of the insulation layer.
19 Consult current Underwriters Laboratories Directory for the appropriate coating for each
roofing assembly to obtain the required fire rating. The assembly shall be installed in
strict compliance with sections 3401.5 and 3401.6 of the South Florida Building Code for
maximum fire classification.
20 The maximum designed pressure limitation listed shall be applicable to all roof pressure
zones (i.e. field, perimeters, corners). No rational analysis, nor extrapolation shall be
permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended
corners, and corners). (When this limitation is specifically referred within this NOA,
General Limitation #7 will not be applicable.)
Page 60 of 61
1111W .
Roofing Product Control Examiner
iN 5. ' 98 9:43 FROM BRADCO MIAMI LATIN
ROOF ftnrCRING MATERIALS (TEV1)
f.4urINt; SYSTEAiS (TGFU)— Continued
t Optiouat): One or more layers pertite, wood fiber, glass
fiber, isocyanurate, urethane, pertite/isocyanurate composite, periite/
urethane composite. wood fiber /isocyanurate composite. phenolic.
Base Sheet Two or more layers of Type G2 or G3.
ply Sheet (Optional): One or more layers of Type 61.
Membrane: One or more layers of "Ruberoid Torch" (smooth or granule),
"Ruberoid Torch Ptus" (granule), "Ruberoid Mop" (smooth or granule) or
"Ruberoid Mop P; rs" (granule).
su facio!g Karnak No. 97, 1 -1/2 - 3 gal/sq or gravel
Deck: NC Iactine: 1/2
Insulation: One or more layers pertite, glass fiber, 3/4 in. min,
isxcyanurate, urethane, pertite/isocyanurate composite, pertite /urethane
composite, phenolic, 1 -1/2 in. min.
Base Sheet (Optional): One or more layers of Type 61, G2 or G3.
Membrane: One or more layers of "Ruberoid Torch" (smooth or granule),
"Ruberoid Torch Plus" (granule), "Ruberoid Mop" (smooth or granule) or
"Ruberoid Mop Plus' (granule).
Surfacing "AL MB Aluminum Roof Coating" at 1 -2 gal /sq,
Deck: C -15/32 ladinm 1/2
Insulation (Optional): One or more Layers pertite, glass fiber, 3/4 in.
min, isocyanurate, urethane, perlite/isocyanurate composite, perlite/
urethane composite. phenolic. 1 -1/2 in. min.
Base Sheet One or more layers of Type G2 "GAFGLAS #75 Base Sheet",
not mopped or mechanically fastened in place.
Ply Sheet One or more layers of Type GI " GAFGLAS Ply 4 ", hot mopped
in place.
Membrane "Ruberoid Mop FR" (granule).
Surfacing (Optional): 6AF Fibered Aluminum Coating at 1 -1/2 gal/sq or
GAF Weather Coat Emulsion at 3 gal /sq.
Deck: C - 15/32 Incline: 1/2
Insulation (Optional): One or more layers pertite, glass fiber, 3/4 in.
min, isocyanurate, urethane. pertite /isocyanurate composite, pertite/
urethane composite, phenolic, 1 -1/2 in. min.
Base Sheet One or more Layers of Type G2 " GAFGLAS #75 Base Sheet",
hot mopped or mechanically fastened in place.
Ply Sheet One or more layers of Type G1 " GAFGLAS Ply 4 ". or " GAFGLAS
Piy 6" hot mopped in place.
Membrane: "Ruberoid Torch FR" (granule).
Surfacing (Optional): GAF Fibered Aluminum Coating at 1 -1/2 gal /sq or
GAF Weather Coat Emulsion at 3 gal/sq.
S1. Dock C•15/32 India*: 1/2
Insulation: Lsocyanurate, 2 in. min.. wood fiber, pertite or glass fiber,
any thickness. hot mopped or mechanically fastened in place. Joints
of..et 6 in. •
Base Sheet One or more layers of Type G2 "GAFGLAS #75 Base Sheet",
hot mopped or mechanically fastened in place.
Ply Sheet (Optional): One or more layers of Type 61 " GAFGIAS Ply 4" or
"Ply 6" hot mopped in place.
Membrane: "Ruberoid Torch FR' (granule).
Surfacing (Optional): GAF Fibered Aluminum Coating at 1.1/2 gat /sq or
GAF Weather Coat Emulsion at 3 gal/sq.
12. Deck: C -15/32 Indio*: 1/2
Insulation (Optional): Isocyanurate, penile or glass fiber, any thickness,
hkx mopped or mechanically fastened in place. Joints offset 6 in.
Base Sheet One or more layers of Type G2 " GAFGLAS #75 Base Sheet",
hot mopped or mechanically fastened in place.
Ply Sheet One or more layers of Type GI " GAFGLAS Ply a or "Pty 6 ". hot
mopped in place.
Membrane: "Ruberoid Torch FR" (granule).
Surfacing (Opnonai): GAF Fibered Aluminum Coating at 1 -1/2 gal /sq or
GAF Weather Coat Emulsion at 3 gal/sq.
13. Deck NC Incline 1/2
Insulation (Optional): Isokyanurate, wood fiber board, perlite, glass
fiber, any thickness. hot mopped or mechanically fastened in place.
Joints offset 6 in.
Base Sheet One or more layers of Type G2 "GAFGLAS 1175 Base Sheet".
hot mopped in place.
Ply Sheet (Optional): One or more layers of Type 61 " GAFGLAS Ply 4" or
'Ply 6" hot mopped in place.
Membrane: "Ruberoid Torch FR" (granule).
Surfacing (Optional): "GAF Fibered Aluminum Coating" at 1 -1/2 gal/sq
or GAF Weather Coat Emulsion at 3 gal /sq.
:c. ileac NC IndtaG 1/2
Insulation (Optional): Lsocyanurate, wood fiber board, perlite, glass
fiber any thickness, hot mopped or mechanically fastened in place.
Joints offset 6 in.
Base Sheet One or more layers of " GAFGLAS 075 Base Sheet ", hot
mopped in place.
Ply Sheet (Optional): One or more layers of "GAF GLAS Ply 4" or "Ply 6"
hot mopped in place.
N UMMI= "Rutecot Notts► F(Y' tgrod.e .
I at194uS■
"Aar trga HIRF'
ROOFING SYSTEMS (TGFU) — Continued
GAF Fibered Aluminum Coating at 1 -1/2 ga/sq.
15. Deck C -15/32 Incline: 1/2
Insulation (Optional): Pertite, fiber glass, isocyanurate, urethane. perlite,
isocyanurate composite or phenolic
Base Sheet: One or more layers Type G2 or 63 base sheet, hot mopped
or mechanically fastened.
Ply Sheet (Optional): One or more layers Type 41, hot mopped in place.
Membrane: "Ruberoid Mop FR" or "Ruberoid Mop 170 FR" (granule).
16. Deck C -15/32 Irrcipe: 1/2
Insulation (Optional): Perlite, fiber glass, isocyanurate, urethane, pertite/
isocyanurete composite or phenolic, offset 6 in, from joints.
Base Sheet One or more layers of Type 6 -2 or G-3 base sheet, hot
mopped or mechanically fastened.
Pty Sheet (Optional): One or more layers of Type 6.1, hot mopped in
place.
Membrane: One layer of "Ruberoid Torch" or " Ruberoid Mop" (smooth).
Membrane: One layer of "Ruberoid Torch FR" or "Ruberoid Mop FR"
(granule)
17. Deltic NC Iaclinec 1
Insulation (Optional): Pertite„ fiber glass, wood fiber, isocyanurate,
urethane, pertite/isocyanurate composite or phenolic
Base Sheet One or more layers Type G2 or G3 base sheet. hot mopped
or mechanically fastened.
Pty Sheet (Optional): One or more layers Type 61, hot mopped in place.
Membrane: One layer of "Ruberoid Mop FR" or "Ruberoid Mop 170 FR"
(granule).
18. Deck: NC Inchon 1/2
Insulation (Optional): Pertite, fiber glass. wood fiber, isocyanurate,
urethane, pertite/isocyanurate composite or phenolic.
Base Sheet (Optional): One or more layers of Type G -2 or G -3 base
sheet, hot mopped or mechanically fastened.
Pty Sheet (Optional): One or more layers of Type 6 -1, hot mopped in
place.
Membrane: One layer of 'Ruberoid Torch" (smooth), "Ruberoid Mop'
(smooth).
Membrane: One layer of "Ruberoid Torch FR" (granule).
19. Deck: NC Iodine: 1/2
Insulation (Optional): One or more Layers of pertite, glass fiber,
isocyanurate, urethane, pertite/isocyanurate composite or phenolic. any
thickness.
Base Sheet One or more plies GI or 62, hot mopped or adhered with
Karnak Chemical Co. "No. 81" or Gibson -Homan 'No. 6160" cold applied
adhesive at 1 -1/2 gal/sq.
Membrane: One layer of 'Ruberoid Mop FR" ,;r ` Ruberoid Mop 170 FR"
(granule). hot mopped or adhered with Karnak Chemical Co. "No. 81" or
Gibson -Doman "No. 6160" cold applied adhesive at 1 -1/2 gal/sq.
20. Cede C•15/32 Incline: 1/4
Insulation: Polyisocyanurate. any thickness.
Base Sheet - GAFGLAS #75" (Type G2), mechanically attached.
Membrane: One or more plies of "Rubberoid Torch (smooth).
Membrane: "Ruberoid Torch FR" (granule).
21. Deck C•15/32 Iodine: 1/
Insulation (Optional): Potyisocyanurate, wood fiber, pertite, glaze fiber
any thickness, hot mopped or mechanically fastened.
Base Sheet One or more plies of Type G2 "GAFGLAS 675" or "Ruberoid 20
FR" base sheets, hot mopped or mechanically fattened.
Membrane: One or more plies of "Ruberoid 30 FR" hot mopped in place.
22. Deck: C -15/32 laciest 1
Insulation (Optional): Polyisocyanurate. wood fiber, pertite, or glass
fiber any thickness. hot mopped or mechanically fastened.
Base Sheet One or more plies of Type G2 "GAFGLAS #75" hot mopped or
mechanically fastened.
Ply Sheet One or more plies of "Ruberoid 20" or "Ruberoid 20 FR', hot
mopped in place.
Membrane: One or more plies of "Ruberoid 30 FR', hot mopped in place.
Class 1-Fully Adhered
I. Deck C -15/32 Inctiee: 1/2
Insulation (Optional): One or more layers pertite, wood fiber, glass
fiber, isocyanurate, urethane, pertite /isocyanurate composite, pertite/
urethane composite, wood fiber/isocyanurate composite. phenolic, any
thickness.
Base Sheet Two or more layers of GAF 6-1, G -2 or G -3 base sheet. hot
mopped or mechanically fastened in place.
Membrane: One or more layers of "Ruberoid Torch" (smooth or granule),
"Ruberoid Torch Pius (granule), "Ruberoid Mop" (smooth or granule) or
"Ruberoid Mop Plus" (granule).
Surfacing: Karnak No. 97 applied at nom 1 -1/2 gal/sq.
2. Deck C•15/32 Irkdine: 1/2
Insulation (Optional): One or more layers perlite, wood fiber. elass
fiber,
isocyanurate, urethane, partite /itocyanuslty comoosm•
urethane composite good flbe" /iaocyanutate composlra, Dimino any
thickness.
T 5967966
toldtpua
PAGE,001 /001
ROOF COVERING MATERIALS (TEVT)•
13;
GAF Materials Corporation
1361 Alps Road
Wayne, NJ 07470
1
NOTICE OF ACCEPTANCE STANDARD CONDITIONS
Product Control No: 97- 0804.14 _
ACCEPTANCE NO.: 97- 0814.14
APPROVED: November 6, 1997
EXPIRES: November 6, 2000
Renewal of this Accep • • ca Ion has been filed and the
original submitted documentation, including test supporting data, engineering documents, are no older than
eight (8) years.
2 Any and all approved products shall be permanently; labeled with the manufacturer's name, city, state, and the
following statement: "Metro -Dade County Product Control Approved ", or as specifically stated in the
specific conditions of this Acceptance.
3 Renewals of Acceptance will not be considered if:
a) There has been a change in the South Florida Building Code affecting the evaluation of this product and
the product is not in compliance with the code changes;
b) The product is no longer the same product (identical) as the one originally approved;
c) If the Acceptance holder has not complied with all the requirements of this acceptance, including the
correct installation of the product;
d) The engineer who originally prepared, signed and sealed the required documentation initially submitted,
is no longer practicing the engineering profession.
4 Any revision or change in the materials, use, and/or manufacture of the product or process shall automatically
be cause for termination of this Acceptance, unless prior written approval has been requested (through the
filing of a revision application with appropriate fee) and granted by this office.
5 Any of the following shall also be grounds for removal of this Acceptance:
a) Unsatisfactory performance of this product or process;
b) Misuse of this Acceptance as an endorsement of any product, for sales, advertising or any other
purposes.
6 The Notice of Acceptance number preceded by the words Metro -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. if any portion of the Notice of Acceptance is
displayed, then it shall be done in its entirety.
7 A copy of this Acceptance as well as approved drawings and other documents, where it applies, shall be
provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site
at all times. The copies need not be resealed by the engineer.
8 Failure to comply with any section of this Acceptance shall be cause for termination and removal of
Acceptance.
9 This Acceptance contains pages 1 through 61
END OF THIS ACCEPTANCE
Page 61 of 61
Frank Zuloaga, _
Roofing Product Control Examiner