Roof•
Location and 1e al description of lot to be built on:
Lot___ o _Block Subdivision
Street and Number where work is to be done _
State work to be done and purpose of building (by floors)
permit, as are licensed by Miami Shores Village.
Council Approved
MIAMI SHORES VI LLAG E
BUILDING INSPECTION DEPARTMENT
APPLICATION FOR BUILDING PERMIT
Application is hereby made for the approval of the detailed t tatement of the plans and specifications herewith submitted for the building
or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami Shores
Village, Florida, and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and regula-
tions of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved plans
and specifications must be kept at building during progress of tht work. • � )
Date _t_ �_,,_t k 1
J �7. F
Owner's Name and Address] i.. • J ri, , o 4, No.___�_ —� Street ,� .
Registered Architect aadf or- Esgiaen t 1 tz, N _t.....! - r'= r �' ' , 1' j - -!' .1_ 1
Name and address of licensed contract , .N ' � F k X°L 1 . �_ ' c'+-`� i /�- -� l_a_.L "- - i A Jr =-'v
Building I ispector
PLANNING BOARD_____._ __DATE -.
Chairman Member
Member ` `Member
Member Member
_ _� _�__� _�� and for no other purpose.
New Building_____ v - ______ Remodeling__ '_ __ Ad __ �_ _ _____ Repairs No. of Stories lit —__ f
To be constructed of -►- —____ Kind o foundatio *.�___ , 6 _ _�it___y__; �-_ I t Roof Covering_ Al _ _�
Estimated Total cost of improvements $1 J �" , _Amount of Permit $
Zone cubage required Z _Plan Cubage c4. -.) f,.-,
Distance to next nearest building Size of Building Lot
Maximum live load to be borne by each floor
I hereby submit all the plans aid specifications for said buildi:ig. All notices. With reference to the building and its construction may
be sent to i i l r i fY �;1 CO I t ! .1! r • 7 ' — t_' i '1' k 4 - 1r 1 - '1 i ji1_.L __ L .
The undersigned applicant for this building Omit does herebl certify that he under and accepts his obligations as an employer
of labor under the Florida Workmen's Compensation Act, being :section 5966, Compiled General Laws of Florida, Permanent Supplement,
and has complied with the provisions thereof, and will require similar compliance from all contractors or sub - contractors employed by him
in the work to be performed under this permit; and will post or cruse to be posted for inspection on the site of the work such public notice
or notices as are required by the Act. The undersigned agrees to em/ loy only such subcontractors. on w9fk to be performed under this
Remarks (Signed) / it 4--' .. i z i d
1
i
STATE OF FLORIDA,
COUNTY OF DADE.
Before me, the undersigned authority, a notary public, duly au.horized to administer oaths and take acknowledgments, personally
appeared
to me well known,
and who, being by me first duly sworn, upon oath deposes and says bat he is the
of the above described construction, that be bas card }tlly read the f. regoing application, and that he did sign the same, and that all facts
therein by him stated are true.
Permit No Date
Disapproved
(Signed) _
Read, Sworn to and Subscribed before me.
Notary Public, State of Florida
My Commission Expires
Date Disapproved _Date
NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval has been obtained from
the Planning Board.
A re- inspection fee of $1.00 will be charged when such re-insp( ction is made necessary by improper notice for inspection or faulty
materials and /or workmanship. ti
•
MIAMI SHORES VILLAGE
APPLICATION FOR BUILDING PERMIT
Application is hereby made for the approval of the detailed statement of the plans and specifications herewith submitted for the building
or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami Shores
Village, Florida, and all provisions of the Laws of the State of Ftarida, all ordinances of Miami Shores Village and all rules and regula-
tions of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved plans
and specifications must be kept at building during progress of the work. 1
*""r 4 i Date_ Date ° ---- - — - „T 19"��' .. CI
y w %+ t..1 ..‹. -
Owner's Name and Address '` "" ' " , S 1 ..! EI/ No.-- __— ____ —_ Street — _
Registered Architect oacI40r∎Eegiae'r C i r �„lt.4,w - __ ti j 1....J,
.. .. +
Name and address of licensed contract A 4,. A- _ x � s -4�. . -- • 'A-` j ` _ itiz.
Location and legal description of lot to be built on: y e .
Lot '! f' _ Block �_ Subdivision J 11 1 £: _ M I 8
Street and Number where work is to be one- __:_______._.
State work to be done and purpose of building (by floors) _
44 4104
Zone cubage requ &red
Distance to next nearest building
Maximum live load to be borne by each floor
Disapproved _______ __________ Date
(Signed)
BUILDING INSPE:,TION DEPARTMENT
Building Inspector My Commission Expires
PLANNING BOARD DATE
Chairman Member _
Member Member
Member Member
Council Approved_ _________— _ —_ —_ _ Date Disapproved
_and for no other purpose.
New Building____ _! a Remodeling_ Addition. ""� Repairs .r No. of Stories_Sf __
To be constructed o ..es ___ Kind of foundation__ _C__ _�_ __
_ As.a „ li�I __.. _ Roof Covering_ ,_. _L t L i
.r_ `* � ' " ' _ of Permit $_ -
/_.
F.
Estimated Total cost of improvements $- 1 t te
_Plan Cubage
Size of Building Lot
I hereby submit all the plans a�jg"�° specifications for said buildit; All notice& reference to th building and its co ruction may
ty.�!'
be sent -�r►--�fa em _- , I l- ,'T ` r 4 "AA ma__ ;- --. t4
The undersigned applicant for this building rmit does hereby certify that he understands and accepts his obligation! as an employer
of labor under the Florida Workmen's Compensation Act, being 5 ction 5966, Compiled General Laws of Florida, Permanent Supplement.
and has complied with the provisions thereof, and will :require simi.ar compliance from all contractors or sub - contractors employed by him
in the work to be performed under this permit: and will post or cause to be posted for inspection on the site of the work such public notice
or notices as are required by the Act. The undersigned agrees to emp.oy only subcontractors., on ,w k to be performed under this
permit, as are licensed by Miami Shores Village. It f
Remarks (Signed) 1• -f P s t t 1 s,... '
f
STATE OF FLORIDA, p u.
COUNTY OF DADE. y�
Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally
appeared
to me well known,
and who, being by me first duly sworn, upon oath deposes and says teat he is the
of the above described construction, that he has care illy read the foregoing application, and that he did sign the same, and that all facts
therein by him stated are true. '
ol �, / ��
Permit No.__'' Date Read, Sworn to and Subscribed before me.
Notary Public, State of Florida
Dzte
NOTE: A charge of $1.00 will be made for making correctio:is or changes to this application after approval has been obtained from
the Planning Board.
A re- inspection fee of $1.00 will be charged when such re- inspection is made necessary by improper notice for inspection or faulty
materials and /or workmanship.
A
BUILDING INSPCECTION DEPARTMENT
Name and address of licensed contractor A.B.
iA n r l'_ I i1
Location and legal description of lot to be built on:
Lot Block
Street and Number where work is to be done
State work to be done and purpose of building (by
R7— R00,1{ SO, 40
MIAMI SHORES VILLAGE
APPLICATION FOR BUILDING PERMIT
Building Inspector
PLANNING BOARD
Subdivision
366 q _,STREET
floors)
.and for no other purpose.
New Building Remodeling Addition Repairs No. of Stories 1 _
To be constructed of Kind of foundation Roof Covering TILE
Estimated Total cost of improvements $ Amount of Permit s. 20.00
Zone cubage required _.._.....Plan Cubage
Distance .to next nearest building Size of Building Lot
Maximum live load to be borne by each floor
I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may
be sent to.
The undersigned applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer
of labor under the Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement,
and has complied with the provisions thereof, and will require similar compliance from all contractors or sub - contractors employed by him
in the work to be performed under this permit; and will post or cause to be posted for inspection on the site of the work such public notice
or notices as are required by the Act. The undersigned agrees to employ only such subcontractors, on work to be performed under this
pennit, as are licensed by Miami Shores Village.
Remarks (Signed)
STATE OF FLORIDA,
COUNTY OF DADE. i ss.
Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap-
peared
_ —. to me well known,
and who, being by me first duly sworn, upon oath deposes and says that he is the.
of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts
therein by him stated are true.
Permit No. Date
Disapproved ........ Date.._.. —
(Signed)
Swo d Subscribed re me.
i ...... ,r.
�•� ary ub ic, State of Florida
y Commission Expires — :... ..._...._..._ _ _.__
NOT "Y PUBLIC S
MPeeMM .s.slaj E „PI�:_� y1960
• Chair;nan Member As :'s3.it;ist ;�rrr�..i
Mferr,ber Member --
Member Member
Council Approved Date Disapproved Date
NOTE: A charge of $1.00 will be made for making corrections or changes to this application after approval has been obtained fmm
the Planning Board.
A re inspection fce of $1.00 will be charged when such re- inspection is made necessary by improper notice for inspection or faulty
materials and /or workmanship.
Application is hereby umdc for the approval of the detailed statculr•nr u► the plans and specifications herewith submitted for the build
inc or other structure herein described. This application Is made in compliance and conformity with the Building Ordinance of Miami
Shores Village, Florida, and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and
regulations of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved
plans and specifications must be kept at building during progress of the work. _ 3 . 3
// //
e ,' Date......_... _�...r...._.rL.1 �..._. _..._... , 19..
Owner's Name and Address . Btl CifEL l::.��:;r:.. ......� — No.751 —605.9 StreetJ. 66 � I _ •.. ST^EET
Registered Architect and /or Engineer I '
"1. 1tI•••t If• ttlttlttttflN H••St.
ROOFING CONTRACTORS 3680 135 STREIT
MIAMI SHORES VILLAGE
BUILDING INSPECTION DEPARTMENT
APPLICATION FOR BUILDING PERMIT
Application is hereby made for the approval of the detailed statement 01 we plans and specifications herewith submitted for the build •
ing or other structure herein described. This application is made in compliance and conformity with the Building Ordinance of Miami
Shores Village, Florida. and all provisions of the Laws of the State of Florida, all ordinances of Miami Shores Village and all rules and
regulations of the Building Division of Miami Shores Village shall be complied with, whether herein specified or not. A copy of approved
plans and specifications must be kept at building during prpgr,:ss of the work.
Date..._..._...__..... March 25 1983
Owner's Name and Address E • L • B LiC�a...
Registered Architect and /or Engineer
Name and address of licensed contractor TtllliCA.... 3.OQlrigcl4QLL..1V . ftlT.....2LL
Location and Legal description of lot to be built on:
Lot Block Subdiv'.sion __ .._ .._�.....
Street and Number where work is to be done 366 1V. E.
State work to be done and purpose of building (by floors) ...__.Reroof entire with 1 lacer 33#,~ felt and
white cement shi al.- .31 ...squares...._
and for no other purpose.
New Bui!ding Remodeling X Addition Repairs No. of Stories 1.
To be constructed of Kind of foundation Roof Covering
Estimated Total cost of improvements $ 7300.00 Amount of Permit $. 20.00
Zone cubage required Plan Cubage
Distance•to next nearest building. Size of Building Lot
\taxirnum live load to be borne by each floor
I hereby submit all the plans and specifications for said building. All notices with reference to the building and its construction may
be sent to.
The unricrsigncd applicant for this building permit does hereby certify that he understands and accepts his obligations as an employer
of labor under the 'Florida Workmen's Compensation Act, being Section 5966, Compiled General Laws of Florida, Permanent Supplement,
anti has complied w ith the provisions thereof, and will require similar compliance from all contractors or sub - contractors employed by him
in the work to be performed under this permit; and will post or cause to be posted for inspection on the site of the work such public notice
or notices as arc required by the Act. The undersigned agrees to employ only such subcontractors. on work to be performed under this
pcnnit, as are licensed by Miami Shores Village. .4.76
Remarks (Signed) t
STATE OF FLORIDA,
COUNTY OF DADE. ss.
Before me, the undersigned authority, a notary public, duly authorized to administer oaths and take acknowledgments, personally ap-
peared J. P . Craig
to me well known,
and who, being by me first duly sworn, upon oath deposes and says that he is the....R00fJ.ng contractor
of the above described construction, that he has carefully read the foregoing application, and that he did sign the same, and that all facts
therein by him stated are true..
11,E 0 .l q b Read, Sworn to and Subsc Date
Disapproved
(Signed) l/
before me.
Date
Building Inspector for M i E
g p My i4i�ic, 3Rilbii •f1erkit-g•farg*•._..._.._.__
l•Jiy Commission Expires wily 8 1S65
PLANNING BOARD DATE
Chairman Member —
r Member
Member .. .. Member ...._
Council Approved Date Disapproved Date
NOTE: A charge of $1.00 will be made for making corredicns or changes to this application after approval has been obtained faun
the Planning Board.
A rc- inspection fee of $1.00 will be charged whets such re- inspection is made necessary by improper notice for inspection or faulty
materials anti /or workmanship.
Notary Public, State of Florida
Date fd - 17 - -1 Job Address 3 (a la MS q) ST.
Legal Description
Owner/Lessee / Tenant
Owner's Address
Square Ft. j J Q
t 95- ZZO
PERMIT APPLICATION FOR MIAMI SHORES VILLAGE
w t/, LoTx, ill Lv+ 3
FV /). Lof S, 811,4 <(7
AleXWivi71:,k Qviv1 -tc:11,7
3 (o(o Phone 20 J - 7,1 - d' -
Signature of owne and/or ondo President Date
N ary as to Owner and/ • • • • • • - Date
/off / /, /y?
scIAL NOTARY SEAL
0 g , . mo / SANDRA M MONTIEL
^, * COMMISSION NUMBER
CC4012
te ? Q MY COMMISSION EXP.
OF 6\- AUG. __. 971 0 9 S
FEES: PERMIT 1 I ` 44 RADON
Tax Folio
Address
APPROVED: 1 f
Zoning Building i `1
Mechanical Plumbing
l/ -3 , -0 /3 -(3}-<
Historically Designated: Yes No
Master Permit #
Contracting Co. 6 U'e k) t ,lajl, J4- l (z
'hone
State # C DO 4-2 r Z Municipal # Competency # Ins. Co.
Architect/Engineer Address
Bonding Company Address
Mortgagor
Permit Type (circle one): BUILDING ELECTRICAL PLUMBING MECHANICAL ROOFING PAVING FENCE SIGN
C LA D
WORK DESCRIP'T'ION
p4 - u-,T Ceti- et tk
Electrical
Estimated Cost (value) 1 4- b b 0, 80
WARNING TO OWNER: YOU MUST RECORD A NOTICE OF COMMENCEMENT AND YOUR FAILURE TO DO SO MAY
RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY (IF YOU INTEND TO OBTAIN FINANCING,
CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT.)
Application is hereby made to obtain a permit to do work and insta1iation as indicated above, and on the attached addendum (if applicable). I
certify that all work will be performed to meet the standards of all l ws regulating construction in this jurisdiction. I understand that separate
permits are required for ELECTRICAL, PLUMBING, SIGNS, POOLS, ROOFING and MECHANICAL WORK.
OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable
laws regulating cons Jna and Tung. Furthermore, I authorize the aio ve-named contractor to dot the work stated.
Notary as to Contractor or Owner - Builder
My Commission Expires:
SUSAN POLLACK
MY COMMISSION 1 CC 568469
lui - EXPIRES: September 28 2000
Mu P• Bonded u Notary PIM Unde.wters
_'s+ -wK a J ■
-1f7
C.C.F. ' � NOTARY BOND 0 °
TOTAL DUE 41
Engineering
6TATE OF FLoR1f)A; COUNTY 0= DADE
2 PIG• ^•e:V C'•^.•r'Pt G`• ®: , .� 9 : - ■ fho
csk p:`ri off.^ on
n;`` T;
_ l
, f, J. 1 r!
rd cap Cv crc c
°..•`�� ou 'cad CounfyeoG:C3
1. Legal description of property and street address:
2. Description of improvement: /ittv Rik
3. Owner(s) name and address:
. Interest in property:
6. Lender's name and address:
by Section 713.13(1)(a)7., Fiorida Statutes.
Name and address:
Section 713.13(1)(b). Florida Statutes.
Name and address:
s gnafure of Owner
Print Owners Name 4vb:1(
Notary Public
Print Notary's Name
My Commission Expires:
01 41 1444"LL
OF P'
NOTICE OF COMMENCEMENT
• PERMIT NO. TAX FOLIO NO. 11 0/3- & LI
STATE OF FLORIDA:
COUNTY OF DADE:
THE UNDERSIGNED hereby gives notice that improvements will be made to certain real property, and in accordance with
Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement.
4-c ,c Ord y>�
36, 6 iv, 93 f-7
Name and address of fee simple titleholder. - 109 t Pirn
.3&& we 93 j7_
4. Contractor's name and address: A 2 f a J(Lt ., .11^
5. Surety:(Payment bond required by owner from contractor, if any)
Name and address:
Amount of bond $
3(019 N/. 93 e / 1/ / /,L Luz )• i-Ot3
&- C ti »,/, /f f ,Jo Pec .v: 1 /
7. Persons within the State of Florida designated b1 9 ner upon whom notices or other documents may be served as provided
8. In addition to himself, Owner designates the following person(s) to receive a copy of the Lienor's Notice as provided in
9. Expiration date of this Notice of Commencement: (the expiration date is 1 year from the date of recording unless a
different date is specified)
Cam1 IC? h
Sworn to and subscribed before me this I $ day of 11 . 19 9
ARY $EA
1 MONTIEL
COMMISSION NUMBER
UL1401281
MY rtdts*Ml$tUION SEP.
*miff. 17,1119 11
97R'576515 1997 DEC 18 13:57
Prepared by: I:UJ An 6ot_1P`
Address: 9 T S s SW 7t6"3
0 (Low Slope Application)
Appendix "E"
UNIFORM ROOFING PERMIT APPLICATION
Contractor's Name: Le164/1 k 41,Liillk? Job Address: 3C0C9 i5 St3
NNW CATEGORY •
0 (Nail-On Tile) 0 (Mortar Tile) *
0 (Asphalt/Fiberglass Shingles) 0 ( Metal Roofs\Wood Shingles & Shakes) 0 (Other)
ROOF TYPE
0 New Roof ale DReovring DRepair ° Maintenance
Flat Roof Area (ft2) Sloped Roof Area (ft 3:1 Total (8 . 3 - 3 - & • Master Permit No.
Exposure category (per ASCE 7-88): Building Classification category (per ASCE 748 table 1):
1
v
Ft
Desk type:
ATTACHMENT
Ft.
Fastener Type:
SPACING
Field:
DETAIL 1 & 2
•Includes Mortar and Adhesive Set Tile
ROOF HEIGHT AND SYSTEM DETAILS (Draw detaib as needed)
Perimeter Corner
Page-1
PROCESS No.
ROOF PLAN
4.
R idgeV mi
MOIRES= I 1
Deck typa
DETAIL 3.
Appendix. "E"
UNIFORM ROOFING PERMIT APPLICATION PROCESS No.
Undertaymenc 3o
Insatadon: NQ
ts' �
ROOT SLCZI
SL s PEA SYSTEM' DESCRIPTION
Il+!t 94616%oz. / L
Fastener type do spaaeg
Cap Shat:
Roof Covering:
ff b Ri#'
Ad's � G
64-Lo- z \ I
Drip edge:
Mv CAL CULATTOP
(Pmaxl: x11. (Aerodynamic Multiplier): ) - !viz: _ Mrt: PCA:
(Pmaz2: x ;1. (Aerodynamic Multiplier): ) - Mrs- PCA:
(Pmax3: x11 (Aerodynamic Multiplier): ) - M: = Mr3: PCA:
ATTACHMENTS REQUIRED
1) Fire Directory Listing Page
2) Dade County Product Control
Notice of Acceptance -Cover Sheet
a) Specific System Description
b) Specific System Limitation
c) General Limitations
d) Applicable Detail Drawings
3) Municipal Permit Aooiic aticn
4) Other Component Approvals
METRO -OAOE
PRODUCT CONTROL NOTICE OF ACCEPTANCE
Altusa Tile, Almar (USA), Inc.
6645 Northwest 77th Avenue
Miami, FL 33166
Your application for Product Approval of
APPROVED:02 /13/97
METROPOLITAN DADE COUNTY, FLORIDA
METRO -DADE FLAGLER BUILDING
BUILDING CODE COMPLIANCE OFFICE
SUITE 1603
METRO DADE FLAGLER BUILDING
140 WEST FLAGLER STREET
MIAMI, FLORIDA 33130 -1563
(305) 375.2901
FAX (305)- 375 -2908
INTERNET: mdcc0l @shadow.ne,
PRODUCT CONTROL SECTION
(305) 3 -2902
FAX (305) 372-6339
Altusa Tile Nail-On, Mortar Set or Adhesive Set One Piece "S" Tile Roofing Tile
under Chapter 8 of the Metropolitan Dade County Code governing the use of Alternate Materials and Types of
Construction, and completely described in the plans, specifications and calculations as submitted by:
Redland Technologies, The Center for Applied Engineering, Inc.
has been recommended for acceptance by the Building Code Compliance Office to be used in Dade County,
Florida under the specific conditions set forth on pages 2 -16 and the standard conditions on page 17.
This approval shall not be valid after the expiration date stated below. The Building Code Compliance Office
reserves the right to secure this product or material at any time from a jobsite or manufacturer's plant for quality
control testing. If this product or material fails t3 perform in the approved manner, the Building
Compliance Office may revoke, modi � Code
ilding fy, or suspend the use of such product or material immediately. The
Code Compliance Office reserves the right to revoke this approval, if it is determined by the Building
Code Compliance Office that this product or material fails to meet the requirements of the S th Florida Building
Code.
The expense ofsucli.testing will be incurred by the manufacturer.
ACCEPTANCE NO.: 96- 1030.03
Renews 94- 0914.0
EXPIRES: 02 /13/00
Raul Rodriguez
Product Control Division
Supervisor
THIS IS THE COVERSHEET. SEE ADDITIONAL PAGES FOR SPECIFIC AND GENERAL
CONDITIONS
BUILDING CODE COMMITTEE
This application for Product Approval has been reviewed by the Metropolitan Dade County B ding Code
Compliance Office and approved by the Building Code Committee to be use. in P de County, F under the
conditions set forth above.
Charles Danger, P.E.
Director
Building Code Compliance Dept.
Metropolitan Dade County
Applicant:
Altusa Tile
Alfareria del Turbio, S.A.
Barquisimeto, Venezuela
PRODUCT CONTROL NOTICE OF ACCEPTANCE
ROOFING SYSTEM APPROVAL
Category: Prepared Roofing
;Sub - Category: Tile
Type: Nail-on/Mortar SetUAdhesive Set
Sub -Type: Clay
Contact:
Carlos J. Fernandez
General Manager
Altusa Tile, Almar (USA), Inc.
6645 Northwest 77t; Avenue
Miami, FL 33166
(305) 471 -5830
Product Control
Approval Date:
Expiration Date:
- System Description
Alfareria del Turbio, S.A. (Altusa), located in Barquisimeto, Venezuela, manufacturers clay roof
tile for nail -on, mortar set or adhesive set applications. All tile is manufactured from natural Venezuelan
clays. This Product Control Approval relates to Altusa's "Altusa S" tile profile. Refer to appropriate
Product Control Approvals for other tile profiles.
The "Altusa S" tile profile is available in a variety of natural clay colors and has matching trim
pieces used for rake hip, ridge hip, and valley terminations. These accessories are manufactured for all
profiles and form a part of this Product Control Approval. Optional rubber or clay eave closures are also
available.
Product Control No.: 96 1030.03
February 13, 1997
February 13, 2000
No.: 96- 1030.03
Altusa rooftiles have been tested in compliance with the South Florida Building Code
requirements for clay, nail -on, mortar set or adhesive set tile applications. The minimum roof slope for
the "Altusa S" nail -on tiles shall be 2 ":12 ". See the "?rofile Drawing" section in this approval for the
"Altusa S" profile drawing. The "Altusa S" profile has been tested for both wind characteristics and static
uplift performance, therefore, any consideration for installation shall be done as a'tMoment Based
System'. Data for attachment calculations is noted in Tables 1 through 4 of this Approval.
Almar (USA), Inc., located in Miami, Florida, is the sole approved importer under contract for
selling and distributing Altusa products in the South Florida jurisdiction.
Frank Zuloaga
Plans Examiner, Product Control Division
Product
#30 Felt
#43 Coated Base
Sheet
Mineral Surface Cap
Sheet
Lenzingtex -ZB 140 59" x 164' roll
Underlayment 22 Ibs/roll
Rainproof 1I
Ice and Water Shield
Ivfopping Asphalt
Flashing Cement
Product Control No.: 96- 1030.03
TRADE NAMES OF PRODUCTS MANUFACTURED OTHERS
Dimensions
N/A
N/A
N/A
30" x 75' roll
36" x 75' roll
or
60" x 75' roll
36" x 75' roll
N/A
N/A
Test
Specifications
ASTM D 226
type 11
ASTM D 2626
•
ASTM D 249
PA 104
PA 104
PA 103
ASTM D3I2
type III or IV
ASTM D 4586
Product
Description
Saturated organic felt
to be used as a nailed
anchor sheet.
Saturated and coated
or base sheet for
single or double ply
un
Mineral surfaced
asphalt roll roofing
for use as a top ply in
a double ply
underlayment system.
Single ply, nail -on
underlayment.
Single ply, nail -on
underlayment with 2"
self - adhering top
edge.
Self - adhering
underlayment for use
as a top ply in a two
ply underlayment
system with
Approved #30 or #43
as the base layer.
Asphalt for bonding a
mineral surface cap to
a mech_ arached base
sheet in a double ply
underlayment system.
Cut back, asphalt
based, asbestos free,
fiber reinforced,
trowel grade cement
for repair and flashing
applications.
Frank Zuioaga
Piar.s 4xarniner, -oduct Cor.troi Division
Manufacturer
generic
generic
generic
Lenzing
Performance, Inc.
with current PCA
Protect -O -Wrap, Inc.
with current PCA
W.R. Grace Co.
with current PCA
generic
generic
Tat Product
Product Dimensions Specifications Description Manufacturer
Asphalt Primer N/A ASTM D 4 I Cut back, asphalt S cneric
based coating used to
facilitate bonding of
dissimilar materials.
Roofing Nails
Tin Caps
Wood Battens
Roof Tile Mortar
( "Ti leTiteTM")
min. 12 ga. with
" head
min. 32 ga.
min. I' /." o.d.
max. 2" o.d.
horizontal
min. I "x4 "for use
with vertical battens
or
min. 1" x 2" for use
alone
PA 114
Appendix E
PA 114
Appendix E
Annular ring shank,
hot dipped, electro or
mechanically gale.
roofing nails for use
in underlayment
attachment.
Corrosion resistant
circular disc for use in
underlayment
attachment
vertical Wood Preservers Salt pressure treated
min. 1" x 4" Institute LP - 2 or decay resistant
lumber battens
Hurricane Clip & Clips PA 114 Corrosion resistant
Fasteners min. '/•" width Appendix E bronze, aluminum,
min. 0.062" thick stainless steel,
galvanized steel or
Clip Fasteners plastic attachment
min. 8d x 1'V." clips for supplemental
tile attachment. Clips
are installed with
corrosion resistant
roofing nails
compatible with the
clip. A hurricane clip
is required on all
nail -on eave tiles.
Frank Zuloaga
Plans Examiner, Product Control Division
Product Control No.: 96- 1030.03
generic
generic
generic
generic
N/A PA 123 Prepared mortar mix Bermuda Roof
designed for mortar Company, Inc.
set roof tile with current PCA
applications.
Product
Roof Tile Mortar
( "Quikrete® Roof
Tile Mortar tt 1 140")
Roof Tile Adhesive
( "Polypro® AH 160 ")
Valley Flashing
Drip Edge
Dimensions
N/A
N/A
min. 26 ga.
min. 16" width
min. 26 ga.
min. 2" face flange
min. 2" deck flange
Test
Specifications
PA 123
See PCA
ASTNI A 525
PA 111
Product
Description
Prepared mortar mix
designed for mortar
set roof tilt
applications.
Two component
polyurethane adhesive
designed for adhesive
set roof the
applications.
Galvanized steel
valley flashing
Galvanized steel drip
edge
Frank Zuloaga
Pars Examiner, Product Control Division
Product Control No.: 96- 1030.03
Manufacturer
Quikrete Construction
Products
with current PCA
Polyfoam Products,
Inc.
with current PCA
generic
generic
Test Azencv
Testwell Craig Laboratories
& Consultants, Inc.
Redland Technologies
Redland Technologies
Redland Technologies
Redland Technologies
Redland Technologies
Redland Technologies
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
The Center for Applied
Engineering, Inc.
Test Identifier
Lab. #AAP -2
7161 -03
Appendix 111
7161 -03
Appendix 11 .
- .• 7161 -03
Appendix 111
94 -83
94 -084
25- 7200 -1
Project No. 307025
Test #MIDC -73
TEST REPORTS
Test Name/Renort
ASTN1 1 167
Static Uplift Testing
PA 102
Wind Tunnel Testing
PA 108
(Nail -On)
Letter Dated Aug. 1, 1994 Wind Tunnel Testing
PA 10S
(Nail -On)
P0631 -01 Wind Tunnel Testing
PA 108
(Mortar Set)
PO402 Withdrawal Resistance Testing
of screw vs. smooth shank nails
Static Uplift Testing
PA 102(A)
Static Uplift Testing
PA 101
(Adhesive Set)
Static Uplift Testing
PA 101
(Mortar Set)
Static Uplift Testing
PA 102
(Quick -Drive Screws, Battens)
Wind Driven Rain
PA 100
Frank Zuloaga
Plans Examiner, Produc: Control Division
Product Control No.: 96- 1030.03
Date
Oct. 1994
Dec. 1991
Dec. 1991
Aug. 1994
July 1994
Sept. 1993
Dec. 1991
April 1994
May 1994
Feb. 1995
Oct. 1994
Deck Type: Wood, Non - insulated
Deck Description: New Construction
19 / 32 " or greater plywood or wood plank.
SYSTEM A: Counter -Batten Application
Slope Range:
SYSTEMS
Product Control No.: 96- 1030.03
2 ":12" to 7" :12"
Note: Counter - Battens, as noted below, are required for slope range
2 ":12" to less Than 4 ":12" and are optional for slopes of 4 ":12" to
7 ":12 ". For slopes exceeding 7 ":12 ", refer to System C.
Underiayment: Install underlayment system in compliance with Dade County Application
Standard PA 118.
Vertical Battens: Install vertical battens in compliance with Dade County Application Standard
PA 1 18
Horizontal Battens: Install horizontal battens in compliance with Dade County Application
Standard PA 118.
Roofing Tile: Install tile in compliance with Dade County Application Standard PA 118.
(See "Data for Attachment Calculations" included in this Approval.)
Comments: I. For re -roof applications ' plywood is an acceptable substrate.
Frank Zuloaa
Pars Examiner, Product Control Division
Product Control No.: 96- 1030.03
SYSTEMS
(CONTINUED)
Deck Type: Wood, Non - insulated
Deck Description: New construction 19 /72" or greater plywood or wood plank.
SYSTEM 13: Direct Deck Application
Slope Range: 4":12" to 7":12"
Note: System /3 is on'sv acceptable in this slope range. For slopes less than
4 ":12 ", refer to System A. For slopes in excess of 7 " :12 ", refer to
System C.
Undcrlayment:
Rooting Tile:
Comments:
Install underlayment system in compliance with Dade County Application
Standard PA 118.
install tile in compliance with Dade County Application Standard PA 118.
(See "Data for Attachment Calculations" included in this Approval.)
1. For re -roof applications, "/ plywood is an acceptable substrate.
Fran.; Zcloaga
P!an:. r xaminer, Product Controi Division
Product Control No.: 96- 1030.03
• SYSTEMS
(CONTINUED)
Deck Type: Wood, Non - insulated
Deck Description: New construction 19 / or greater plywood or wood plank.
SYSTEM C: Horizontal Batten Application
Slope Range: 4":12" or greater
Note: Horizontal battens, as noted below, arc required for slopes in excess
of 7 ":12" and are optional for slopes of 4 ":12" to 7 ":12 ". For slopes
less than 4 ":12 ", refer to System A.
Underlayment:
Install underlayment system in compliance with Dade County Application
Standard PA 119.
Horizontal Battens: Install horizontal battens in compliance with Dade County Application
Standard PA 119.
Roofing Tile:
Comments: 1. For re -roof applications, ' plywood is an acceptable substrate.
Install tile in compliance with Dade County Application Standard PA 119.
(See "Data for Attachment Calculations" included in this Approval.)
10
Frank Zuloaga
FL: r.s Exs<iirer Pr ,duct Cont; of Division
Product Control No.: 96- 1030.03
SYSTEMS
(CONTINUED)
Deck Type: .Wood, Non - insulated
Deck Description: New construction t / „” or greater plywood or wood plank.
SYSTEM D: Mortar or Adhesive Set Application
Slope Range: 2 ":12" to 7" :12"
Note: System D is only acceptable in this slope range. For slopes in excess
of 7 ":12 ", refer to System C.
Underlayment:
Roofing Tile:
Comments:
Install underlayment system in compliance with Dade County Application
Standard PA 120. (See System Limitation #5.)
Install tile in compliance with Dade County Application Standard PA 120.
(See "Data for Attachment Calculations" included in this Approval.)
I. For re -roof applications, 'S /,," plywood is an acceptable substrate.
Frank Zuloaga
:Fiats Exzminer, Froduct Control Division
DATA FOR ATTACHMENT
CALCULATIONS
Altusa 'S' Tile
Tile
Profile
Altusa 'S' Tile
Altusa 'S' Tile
Tile
Profile
Tile
Profile
Battens
4.47
3 ":12"
or less
Table 1: Aerodynamic Multipliers -A (ft')
Table 2: Restoring Moments due to Gravity - M (ft-Ibf)
from PA 102 Testing
Direct I Battens
Deck ( I
5.35 I 4.40
4 ":12"
X (ft')
Batten Application
Direct
Deck
5.27
Tile
Application
Adhesive Set
12
0.29 0.31
Product Control No.: 96- 1030.03
X (ft')
Direct Deck Application
5 ":12" 6 ":12" 7 ":12" or
greater
Battens Direct Battens Direct Battens Direct
Deck Deck Deck
4.31 5.16 I 4.20 I 5.03 4.08 N/A
Table 3: Attachment Resistance Expressed as a Moment - M, (ft-Ibf)
from PA 102 and PA 102(/‘) Testing
TILE APPROVED APPROVED' APPROVED
APPLICATION NAILS SCREWS FIELD CLIP
WITH:
Tile
APPROVED
Profile
EAVES CLIP
WITH:
1 nail 1 2 nails 1 screw 2 screws' 1 nail j 2 nails 1 nail 12 nails
Altusa 'S' Tile I Battens I N/A I N/A I N/A 26.80 I N/A I NIA N/A N/A
Direct Deck 6.20 I 8.40 I 28.70 58.20 I 21.20 I 25.30 26.90 34.90
1. Quik -Drive screws installed in two manufactured holes located 1' /8" and 1 5 / 5 " from the head of the tile.
Table 4: Attachment Resistance Expressed as a Moment - M, (ft-Ibf)
from PA 101 Testing
Attachment -
Resistance
Mortar Set 24.50
66.50
Franc Zuloaga
P;a s Exar.!iner, Product Control Divisior.
•
PROFILE DRAWING
ALTUSA "S" CLAY ROOF TILE
10"
DOVE TAIL
LOCKS
i3
Franc. uloaga
?fans Examiner, Product Control i
D ;vision
• Product Control No.: 96- 1030.03
Ntb
-. 'e -0 O]•'
PROFILE DRAWING
APPROVED SCREW
15
0 1 3 1 - -
Frank Zuloaga
Plar.s Examiner, Pr•oc'jc: Control Division
Product Control No.: 96- 1030.03
•
BIRD STOP
PROFILE DRAWING
ALTUSA "S" CLAY ROOF TILE
ACCESSORIES
NAIL
ROLE -
14
Product Control No.: 96- 1030.03
GABLE-RAKE
Fran • uloaga
Plans Examiner, Product Control Division
Altusa Tile, Almar (USA), Inc.
6645 Northwest 77th Avenue.
Miami Fl 33166
Product Control No.: 96- 1030.03
ACCEPTANCE NO.: 96 - 1030.03
APPROVED : February 13 1997
EXPIRES : February 13 2000
NOTICE OF ACCEPTANCE STANDARD CONDITIONS
I . Renewal of this Acceptance (approval) shall be considered after a renewal application has been filed and
the original submitted documentation, including test supporting data, engineering documents, are no older
than eight (3) years.
2. Any and all approved products shall be permanently labeled with the manufacturer's name, city, state, and
the following statement: "Dade County Product Control Approved ", or as specifically stated in the specific
conditions of this Acceptance.
3. Renewals of Acceptance will not be considered if:
a) There has been a change in the South Florida Building Code affecting the evaluation of
this product and the product is not in compliance with the code changes;
b) The product is no longer the same product (identical) as the one originally approved;
c) If the Acceptance holder has not complied with all the requirements of this acceptance,
including the correct installation of product;
d) The engineer who originally prepared, signed and sealed the required documentation
initially submitted , is no longer practicing the engineering profession.
4. Any revision or change in the materials, use, and/or manufacture of the product or process shall
automatically be cause for termination of this Acceptance, unless prior Nvritten approval has been requested
(through the filing ofa revision application wit't appropriate fee) and granted by this office.
5. Any of the following shall also be grounds for removal of this Acceptance:
a) Unsatisfactory performance of this product or process:
b) Misuse of this Acceptance as an endorsement of any product, for sales, advertising or any
other purposes.
6. The Notice of Acceptance number preceded by the words Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the Notice of Acceptance is
displayed, then it shall be done in its entirety.
7. A copy of this Acceptance as well as approved drrwings and other documents, where it applies, shall be
provided to the user by the manufacturer or its distributors and shall be available for inspection at the job
site at all times. The copies need not be resealed by the engineer.
8. Failure to comply with any section of this Acceptance shall be cause for termination and removal of
Acceptance.
9. This Acceptance contains pages 1 through 17.
END OF THIS ACCEPTANCE
17
Fran • Lu oaga
Plans Examiner, Product Control Division
9
•
1
SYSTEM LIMITATIONS
16
Franz Zuloa ,a
P :.ns Examiner, Product Control Division
Product Control No.: 16- 1030.03
I. The standard minimum roof pitch for Altusa "S" high profile tile shall comply with Dade County
Application Standards PA 118, PA 119 0- PA 120. depcndin�tt on the method of installation.
For nail -on applications, fasteners for mechanical attachment of tiles shall have a head diameter
larger than that of the preformed holes in the tile.
3. System installation shall be in compliance with the system specifications outlined in this Product
Control Approval. The method of attachment utilized shall provide sufficient attachment resistance
expressed as a moment to meet or exceed the required moment of resistance determined in
compliance with Dade County Protocol PA 115 or PA 127. Altusa "S" Tile tile profile has been
tested for both wind characteristics and static uplift performance, therefore, attachment calculations
for installation in compliance with PA 115 or PA 127 shall be done as a 'Moment Based System'.
4. For mortar or adhesive set tile applications, a field static uplift test by a Dade County accredited
testing agency, in compliance with Dade County Protocol PA 106, shall be performed.
5. For mortar set tile applications, 30/90 hot mopped underlayment applications may be installed
perpendicular to the roof pitch unless stated otherwise by the underlayment material manufacturer's
published literature.
6 All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo for
identification in the field.
7. Applications for roofing permits shall include a completed Sectionll of the Uniform Building
Permit, a copy of Pioneer's current specifications and details, a copy of this Product Control
Approval and a copy of the Product Control Approval of any Roofing Component used in the
proposed tile application. Reference shall be made to appropriate data for the required fire rating.
8. The applicant shall retain the services of a Dade County certified testing laboratory to maintain
quality control in compliance with the South Florida Building Code and related protocols. Samples
taken shall be in compliance with Dade County Protocol PA 112, Appendix 'A'.
!AN Setak
3731 SW. 47th Avenue, Suite #401, Davie, Florida 33314 Ph: (954) 584 -4475 Fax: (954) 584 -3887
TESTING ENGINEERS • CONCRETE • SOIL • ASBESTOS 0 STEEL • ASPHALT • ROOFING • ENVIRONMENTAL AUDIT
Client: Arguelles & Arguelles
9455 S. W. 78th Street
Miami, Florida 33173
Att. Mr. Daniel Arguelles
Project: 366 N.E. 93rd Street Tech. R. Binns
Miami Shores, Florida
Tile /Manufacturer: Altusa, clay, Spanish "S"
Test Required: South Florida Building Code Protocol PA 106 -95
Project Description
The roof of the above listed structu:ce had been set with approximately 37
squares of roof tile.
Tile Description
The tiles were a mortar set, clay, Spanish "S ", roof tile manufactured by
Altusa.
Test Procedure
CERTIFICATE OF TEST AND ANALYSIS
The roof was first examined for loose tile by hand lifting one hundred
sixteen (116) field tiles and one hundred thirty six (136) corner and
perimeter tiles. Forty five (45) single tiles, were randomly selected and
tested. Twenty five (25) tests were conducted in the field area, ten (10)
in the perimeter area, and ten (10) __n the corner areas. The single tiles
were subjected to a concentrated uplf_ft force measured with a manually
operated, Chatillon mechanical dial push /pull gauge, series DPPH. The
gauge was connected to a steel "L" shaped angle that was inserted under the
nose of the tile and gradually pulled upward until reaching the required
test pressure of 35 lbs. +/- 5 lbs.
As the load was applied, observations for failure of the component and the
attachment, if any, were recorded. Tests were performed in respective order
as illustrated on the attached sketch.
PO -109
Date: 7/31/98
Lab #: ABM -67
ALL STATE ENGINEERING & TESTING CONSULTANTS, INC.
Client: Arguelles & Arguelles
Project: 366 N.E. 93rd Street
Miami Shores, Florida
Completion Date: > 30 days as per client
Required Testing Force: 35.0 + 5 lbf.
Date: 7/31/98
Tech. R. Binns
Lab #: ABM -67
Comments: The above listed test meets the South Florida Building Code,
Protocol PA 106 -95 static uplift test criteria. The Protocol PA 106 -95
test reported in report No. ABM -67 has been performed in full accordance to
the requirements of Dade County, with no deviations.
Rahimuddi Rahimi, P.E.
Reg. State of Florida # 51484
Field
Field
Perimeter
Corner
1.
pass
19.
pass
1.
pass
1.
pass
2.
pass
20.
pass
2.
pass
2.
pass
3.
pass
21.
pass
3.
pass
3.
pass
4.
pass
22.
pass
4.
pass
4.
pass
5.
pass
22.
pass
5.
pass
5.
pass
6.
pass
23.
pass
6.
pass
6.
pass
7.
pass
24.
pass
7.
pass
7.
pass
8.
pass
25.
pass
8.
pass
8.
pass
9.
pass
9.
pass
9.
pass
10.
pass
10.
pass
10.
pass
11.
pass
12.
pass
13.
pass
14.
pass
15.
pass
16.
pass
17.
pass
18.
pass
ALL STATE ENGINEERING & TESTING CONSULTANTS, INC.
Client: Arguelles & Arguelles
Project: 366 N.E. 93rd Street
Miami Shores, Florida
Completion Date: > 30 days as per client
Required Testing Force: 35.0 + 5 lbf.
Date: 7/31/98
Tech. R. Binns
Lab #: ABM -67
Comments: The above listed test meets the South Florida Building Code,
Protocol PA 106 -95 static uplift test criteria. The Protocol PA 106 -95
test reported in report No. ABM -67 has been performed in full accordance to
the requirements of Dade County, with no deviations.
Rahimuddi Rahimi, P.E.
Reg. State of Florida # 51484
ALL STSTE ENGINEERING & TESTING & CONSULTANTS,
Client: Arguelles & Arguelles
Project: 366 N.E. 93rd Street
Miami Shores, Florida
INC.
Date: 7/31/98
Tech. R. Binns
Lab #: ABM -67