The URL can be used to link to this page

RF-10-783Inspection Number: INSP - 142420 Permit Number: RF -5 -10 -783 Scheduled Inspection Date: November 05, 2010 Inspector: Bruhn, Norman Owner: , BARRY UNIVERSITY Job Address: 11300 NE 2 Avenue Dalton Hall Miami Shores, FL 33138 -0000 Project: <NONE> Contractor: EZ CAULKING & WATERPROOFING INC Building Department Comments Inspection Worksheet Miami Shores Village 10050 N.E. 2nd Avenue Miami Shores, FL Phone: (305)795 -2204 Fax: (305)756 -8972 DALTON DORMERS REMOVE Failed Correction Needed Re- Inspection Fee No Additional Inspections can be scheduled until re- inspection fee is paid. Inspector Comments November 04, 2010 For Inspections please call: (305)762 -4949 Permit Type: Roof Inspection Type: Final Roof Work Classification: Repair Roof Phone Number Parcel Number 1121360010160 -17 Phone: (954)427 -9942 Page 1 of 7 MIAMIDA COUNTY BUILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION NOTICE OF ACCEPTANCE (NOA) Active Ventilation Products 311 First Street Newburg, NY 12550 -4857 MIAMI -DADE COUNTY, FLORIDA METRO -DADE FLAGLER BUILDING WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -2901 FAX (305) 375 -2908 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by Miami -Dade County Product Control Division and accepted by the Board of Rules and Appeals (BORA) to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Division (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BORA reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Division that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Aura -D Ventilator LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. ff any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This renews NOA#04-0622.03 and consists of pages 1 through 3. The submitted documentation was reviewed by Alex Tigera. NOA No.: 09- 0806.08 Expiration Date: 08/05/14 Approval Date: 09/23/09 Page 1 of 3 ROOFING COMPONENT APPROVAL Category: Roofing Sub - Category: 07720 Ventilation Tom: Static Roof Vent Materials Aluminum Deck Wood TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: Test Product Product Dimensions Specification Description Aura -D (AV -24) Vent Vent : 28" dia. x 10" high Deck Flange: 30" x 30" x 6-1/2" All parts 0.40" thick MANUFACTURING LOCATION: 1. Newburgh, NY EVIDENCE SUBMITTED Test Agency PRI Asphalt Technologies, Inc. APPROVED ASSEMBLY: System Type A: Cutout: Test Identifier TAS 100(A) Mechanical attachment of static vent over composite shingles. Factory assembled 24" opening aluminum static ventilation system. Description Date AVP- 005 -02 -01 TAS 100 09/24/03 At chosen location and centered between two roof rafters and aligned a minimum of 18" from the ridge, cut a 24" diameter hole through shingles and sheathing boards. Installation: Starting with a shingle course down roof edge closest to horizontal centerline of the 24" cutout, roll all shingles in the area carefully upward, and completely remove all shingle nails that are exposed and within the area enclosed by the flange. Apply 3 4" continuous bead of approved roofing cement around the outside perimeter of the opening and two 4" beads of roofing cement beneath the vent flange at 1" and 2" respectively from the perimeter of vent flange, carefully slide upper half of flashing up roof beneath shingles previously rolled back, until base is centered over 24" cutout. Secure the base unit to roof using 11 ga. ring shank nails 1" from the edge at all four corners. Next place nails at approximately 7" o.c. from the corners and 1" from the outside edge of the flange. Use a minimum of (16) sixteen nails (See Fastening Pattern below). Nails shall be of sufficient length to penetrate through roof sheathing a minimum of 3 /16 " . Apply approved roofing cement to underside of shingles overlapping flashing, and press them down onto the flashing. Seal all nails and shingles edges with an approved roofing cement. Net Free Area: Refer to manufacturers published literature. NOA No.: 09- 0806.08 Expiration Date: 08/05/14 Approval Date: 09/23/09 Page 2 of 3 1 LmirrATIONS: 1. Refer to applicable Building Codes for required ventilation. 2. Aura -D (AV -24) Vent shall comply with applicable Building Code. 3. This acceptance is for installations over asphaltic shingle or low slope roofing. 4. Aura -D (AV -24) Vent Vent shall not be installed on roof mean heights greater than 33 feet. 5. Aura -D (AV -24) Vent shall comply with 1517.6 of the Florida Building Code (FBC). 6. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 9B -72 of the Florida Administrative Code. DETAIL 30" 30" Aura D Vent END OF THIS ACCEPTANCE NOA No.: 09 -0806.08 Expiration Date: 08/05/14 Approval Date: 09/23/09 Page 3 of 3 OW 10 -906 NOTICE OF COMMENCEMENT A RECORDED COPY MUST BE POSTED ON THE JOB SITE AT TIME OF FIRST INSPECTION PERMIT Nag-C10 to TAX FOLIO NO 000 -0050 STATE OF FLORIDA: COUNTY OF MIAMI -DADE: THE UNDERSIGNED hereby gives notice that improvements will be made to certain real property, and in accordance with Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement. 4S'Pi Ind..by -i i (Na. ALA4 5 A 6� " ° 3 w lob► Ave 5 zo w iL 356 1. Legal description of property and street/address: 11300 NE 2 AVE MIAMI SHORE 36 52 41 40 AC SE1 /4 OF NE1 /4 LESS E35FT & LESS W4OFT LOT SIZE 1740400 SQUARE FEET 2. Description of improvement: Dalton Dormers 3. Owner(s) name and address: BARRY UNIVERSITY, INC. 11300 NE 2ND AVE. MIAMI FL 33161 Interest in property: Name and address of fee simple titleholder: 4. Contractor's name, address and phone number: INFINITY ROOFING AND SHEET METAL, INC. 1150 SW 10TH AVE STE 201W POMPANO BEACH FL 33069 5. Surety: (Payment bond required by owner from contractor, if any) Name, address and phone number: NA Amount of bond $ 6. Lender's name and address: NA 7. Persons within the State of Florida designated by Owner upon whom notices or other documents may be served as provided by Section 713.13(1)(a)7., Florida Statutes, Name, address and phone number: NA 8. In addition to himself, Owners designates the following person(s) to receive a copy of the Lienor's Notice as provided in Section 713.13(1)(b), Florida Statutes. Name, address and phone number: NA 9. Expiration date of this Notice of Commencement: (the expiration date is 1 year from the date of recording unless a different date is specified) WARNING TO OWNER: ANY PAYMENTS MADE BY THE OWNER AFTER THE EXPIRATION OF THE NOTICE OF COMMENCEMENT ARE CONSIDERED IMPROPER PAYMENTS UNDER CHAPTER 713, PART I, SECTION 713.13. FLORIDA STATUTES, AND CAN RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY A NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE COMMENCING WORK OR RECORDING YOUR NO • COMMENCEMENT Signature(s) of Owne By Print Name Title /Office )' Authorized Officer /Director/Partner /Manager By Print Name Title /Office A d - Z . 1 / . . 4 S S 7 /. 4) • STATE OF FLORIDA COUNTY OF MIAMI -DADE The foregoing instrument was acknowledged before me this Q l day of F! p By 13r. c-' , a r ❑ Individually, or Z11 as VP fi). r rM, for - Bca- -- =� ! Personally known, or ❑ produced the following type of identificat • n: Signature of Notary Public: Print Name: (SEAL) VERIFICATION PURSUANT TO SECTION 92,525. FLORIDA STATUTES Under penalties of perjury, I declare that I have read the foregoing and that the facts stated in i e true, to the best of my knowledge and belief. Signature(s) of 0 7 By 123.01 -52 PAGE3 11/07 S. iv 111111111111111111111111111111111111111111111 Space above reserved for use of recording office 1; ^ � `i • — CFN 2010R0309946 OR Bk 27277 Ps 4855; (fps) RECORDED 05/10/2010 09:19:50 HARVEY RUVII'dp CLERK OF COURT 11IA11I —DADE COUI'ITYp FLORIDA LAST PAGE 204, LINnA S. MITTS Notary Public - State of Florida My Comm. Expires Jun 16, 2013 Commission N DD 863031 Bonded Through National Notary Assn. er(s)'s Authorized Officer /Director /Partner/Manager who signed above: By ts2c n�r� BUILDING PERMIT APPLICATION FBC 2004 Permit Type (circle): Building (hoofing) Owner's (Fee Simple Titleholder) BARRY UNIVERSITY Owner's Address 11300 NE 2 AVE City MIAMI SHORES Tenant/Lessee Name Job Address (where the work is being done) 11300 NE 2 AVE - Dalton Hall City Miami Shores Village County Miami -Dade FOLIO / PARCEL # 11- 2136- 000 -0050 Contractor's Address 1150 SW 10TH AVE STE 201W City POMPANO BEACH State FL Qualifier Name JOHN B MITALA State Certificate or Registration No. CCCO57467 r Value of Work For this Permit Miami Shores Village 13011IT311 Building Department `'= 7,C)1 Tel: (305) 795.2204 Fax: (305) "al 10050 N.E.2nd Avenue, Miami Shores, Florida 33138 756.8972 BY:... Permit No. gr-10 Master Permit No. State FL Zi 33161 Phone # Type of Work: ❑Addition ❑Alteration ['New Describe Work: Dalton Dormers q a L, ) Is Building Historically Designated YES NO D r Contractor's Company Name INFINITY ROOFING AND SHEET METAL, INC. phone # 954 917_7107 S4 Zip Zip 33069 Phone # 954 - 8494778 Certificate of Competency No. Architect/Engineer's Name (if applicable) Phone # (700 / rare / Linear Footage Of Work: +/ / /f eplace ❑ Demolition ******** , * * * * * * ** * * * * * * * * * * * * * * * * * * * * ** F ees * * * * * * * * * * * * * *** * * * * * * * * * * ** * * ** * * * * * * * *** r Submittal Fee $ Permit Fee $ 1127 CCF $ '(_12. J CO/ C Notary $ 1 raining/Education Fee $ �p Technology Fee $ la • Vu Scanning $q .00 Radon $ DPBR $ Zoning $ Code Enforcement $ Double Fee $ Bond $ Structural Review. $ Total Fee Now Due $ 1 34•(0( See Reverse side - Bonding Company's Name (if applicable) N/A Bonding Company's Address City State Zip Mortgage Lender's Name (if applicable) N/A Mortgage Lender's Address City State Zip Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRICAL WORK, PLUMBING, SIGNS, WELLS, POOLS, FURNACES, BOILERS, HEATERS, TANKS and AIR CONDITIONERS, ETC OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. "WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT." Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must promise in good faith that a copy of the notice of commencement and construction lien law brochure will be delivered to the person whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site for the first inspection whi ' occurs seven (7) days after the building permit • issued In the absence of such posted notice, the inspection will not be ap ; ed r a reinspection fee will be charged. Signature Owner or Agent The foregoing instrument was acknowledged before me this e? day of Apr, l , 20 10 , by L� � �r a �c%. r X 5 , day of M , 20 , b JOHN B MITALA who is ,personally known to me or who has produced who i ersonally known to me r who has produced As identification and who did take an oath. NOTARY PUBLIC: Sign: 4 Print: L LINDA S. MITTS Notary Public - State of Florida • • = My Comm. Expires Jun 18, 2013 • . 1 Bonded Through Natal Notary Assn. (Revised 07/10/07) , My Commission Expires: AN, ANL a a a a a Signature The foregoing in Contractor ent was acknowledged before me this 5 as identification and who did take an oath. NOTARY P C: Sign: Print: My Com issi Fxpj e _ , k ********* * ** * * ** * * * * * * * * * * * * * * * * * * * * ** ** * * * 4 * ** ,� g �,s��y pt�i . tr a s r ° = N otary Public - State of Florda My Comm. Expires Jun 10 APPLICATION APPROVED BY: J c 0 �.•• Commisiltban0 > 14 , 2013 Engineer Zoning Permit No: 10 -783 Job Name: May 11, 2010 Building Critique Sheet M iami Shores Viiiage Building Department 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 1) Plans must be reviewed and approved by Miami Dade County DERM. 2) A demolition permit application is required from a licensed general contractor. 3) Provide structural repair detail from a licensed architect or engineer. Plan review is not complete, when all items above are corrected, we will do a complete plan review. If any sheets are voided, remove them from the plans and replace with new revised sheets and include one set of voided sheets in the re- submittal drawings. Norman Bruhn CBO 305 - 795 -2204 Page 1 of 1 05/11/2010 08:48 FAX 1 800 685 7530 DATA SCAN FIELD SERVICES II001 TRANSMISSION OK * * * * * * * * * * * * * * * * * * * ** * ** TX REPORT * ** * *** * * * * * * * * * * * * * * * ** TX /RX NO 0001 RECIPIENT ADDRESS 9549177108 DESTINATION ID ST. TIME 05/11 08:47 TIME USE 00'19 PAGES SENT 1 RESULT OK RECEIPT PERMIT #: 1 9 ~ 7 &3 DATE: 507(0 Contractor ❑ Owner ❑ Architect Picked up 2 sets of plans and (other) Address: From the building department on this date in order to have corrections done to plans And /or get County stamps. I understand that the plans need to be brought back to Miami Shores Village Building Department to continue permitti g process. Acknowledged by: PERMIT CLERK INITIAL: RESUBMITTED DATE: 2,0 I l PERMIT CLERK INITIAL: ,s-} n R 'c dnsr M iami Shores Viiiage Building Department 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 / 40,6, , a ( Lirip and Removal Glove Bag Bulldozer Wrecking Ball V Wet Method • Dry Method Explode Bum Down OTHER: MI ICT f'1n-relt.t Dotno neoa ♦ nnn.l.r.. v.,-........ ........ _ . __... .. —___– TYPE OF NOTICE (CHECK ONE ONLY): ❑ REVISED Q CANCELLATIO TYPE OF PROJECT (CHECK ONE ONLY):0 DEMOLITION 0 RENOVATION ROOFING IF DEMOLITION, WAS IT AN ORDERED DEMOLITION? ❑ YES ❑ NO IF RENOVATION: IS IT AN EMERGENCY RENOVATION OPERATION? ❑ YES IS IT A PLANNED RENOVATION OPERATION? ❑ YES ❑ NO v is 0, FE:MOr FLORTDA Florida Department of Environmental Protection Division of Air Resource Management NOTIC OF ASBESTOS RENOVATION OR DEMOLITION : OR Facility Name • &tl ' n /rf2rs /it' _ Dvr1 Address /A 0 2444 ill/ 41Ae. Cit maim 6 '4 q .p, j Zip 33/6 / County Q 6 Site Building Size 8v aJ Prior Use: (Square Feet) # of Floors 02- Age in Years Residence Small Business Other Present Use = ool/College/Unlvers Residence Small Business Other e/Universi Facility Owner fc� f / ` Sl � • /Coll _ Address / /•300 0✓ � /97,/e„40., City / cSAorej Contractor's Name Address /50 .S /0 City f O1pO4O Gds, Florida Licence No. C_G . 175 ?4 IV. Scheduled Dates: Asbestos Removal (mm/dd/yy) Start /VA Finish: V. Procedures to be Used (Check All That Apply): VII. Asbestos Waste Transporter: Name •S •S •7 Address l i///6/ Cit L41473Ji14 State VIII. Waste Dis osal Site: Name sas Address M S, ra D Cit 1-1:10 IX. Amount of RACM OF ACM square feet surfacing material linear feet pipe cubic feet of RACM off facility components square feet cementitious material square feet resilient flooring square feet asphalt roofing ES, /Pe Name of Owner ►: 1 D US ONLY Postmark/Date Recejved State 1GL State rite 3316 cry( ,� % -• 02114) State FL. Zip 3- State P6.- Is the contractor exempt from licensure under section 469.004(7), F.S.? o I m1 5/20/i4 dd/yy) Start Finish: / VI. - Procedures for Unexpected RACM: Ut7U6 (Signature o * wner /O._ -rator (Date) fL- Zip File # ❑ NO °� Process # A i () tit n. e y Ma g ment Consultant Inspecting Site /Wig Zi 3 3 6 �IIrAI�ir�L7,4 E D.I.R•M. AIR QUALITY MANAGEANT DIVISION This is to certify that thregwred Notifications) Regarding asbestos have been submitted in Compliance with plicable r - - - ' ns 4, Signed 33 V-Z ID# Phone (3Of)X99'395J Phone 6 f,9 90 Phone ( ) ceder eo0 Class to I certify that the above•information is correct and that an individual trained in the provisions of this regulation (40CFR Part 61, Subpart M) will be on -site during the demolition or renovation and evidence that the required training has been accomplished by this person will be available for inspection during normal business hours. U4 a 'ze (Contact Phone #) Dept. of Environmental Resources Mgmt. Air Section 33 S.W. 2nd Avenue, Suite 9 -223 Miami, Florida 33130 -1540 Date ❑ YES LlJ" NO (c7 HIGH- VELOCITY HURRICANE ZONES HIGH - VELOCITY HURRICANE ZONES 4 UNIFORM PERMIT APPLICATION model SuUftr Code Edition* 01 Val 01 >..u..:u.. -., iv• ;. mo w,. ;kV 06 2010 COMPLETE PLETE THE NECESSARY SECTIONS • .OF _o ®000ee THE UNIFORM ROOFING PERMIT APPLICATION FORM AND ATTACH THE REQUIRED DOCUMENTS AS NOTED BELOW: 44.20R ATTACHMENTS: REQUIRED: :. Fire Directory Paring Pads 2. From Frotludt Approve!: Proat Pegs SPeC S 1. Deeratitiop Sperm Sy** UrnitOolos ral Lireitetions Applicable Lett Dry Design Calculation per Section R4403, or if Applicable, RAS 127 or RAS 128 Otter Dem Produce ° ro w .�'�• ., - •. � ers .��Qr+i� � . ... iL'_.' " =��., £•: °13 Lid °. -.�� • X i Roofs ri : uttee rati Miami Shores VillagQ DATE. SUBJECT i O CCMPLIANCE WITH ALL FEDERAL ST,ATE AND UL UN ill MULES AND REGULATIONS INSTRUCTION .PAGE FLORIDA BUILDING CODE — RESIDENTIAL. Phut& lin Soto roam UK= .Holt. lid A .a 1 0 1 g Pr Contrictoest Woe. .: _,r A . A any(. , //300 `✓I 02 Low siopee. Mer.hanicalltriastimeiVnte atiotarikoosIve Set The itoOliffEc tee. :13-11.ittomong Reitor ! Mottesince Okr 71/6 'ir) 4.... • FLORIDA BUILDING CODE • RESIDENTIAL • hore.i 4 04LRAj HIGH - VELOCITY HURRICANE ZONES ES • • e•.... .. • > n ,� ' Fes:IllI r e . scuff ;a o w 11 . 6 00. Iris ! ` raj a f .e,.. ' r t.. m c. s! e Y t, qq • S ^ g �'+ d 2 # x ��g• i � ( r , fi b ? S .h r : 3 4... . -..j i^} � S, �,.... :1 17. 6.«t ° . 4 ' '• •s.w .c — . c .€ � p •M �5 S �#'�w.'` - T I ° y �£ f E- �- z• .; • '{ t 1 �. F I .� f 4 R #^: '3' a '"'e- w• A i i a -» s( ; , ▪ . t„r 4 S S .„ ,, t.... l .., , ....j.. # a 3 S , e S ' . 3 F I F c • F ., . 3 t £ ' ' —£ .+s. w 1.-.4.-.-4.!--' }} „' ( °•W s 1 . £ + _! .,,,1� • - ,y • ..t • - . • r f ..€,"' `t"' •� b L,. ,.t - - " ''i• t _ t tN£ c .s�.•. s r. ^ .- 3 I 3 4..,..: --7 w • • 5 :E i -.� e., c i •t,'•• t"i t £ - Y ' § w-. ,� t. -1.7• 5S.0. t ...'s C �' 1 f s 'e' € 1 } . !. ^✓ ... 3 F "t —'- } t t ....•r s t44 3 s t . '1I e t f t..l . y K e . F 3 k• 1 3 , s..• F # ! s t i.. y f ."., f d...3 ,. «S t i £.� yI >"P` £ . '.£ 4 ` i s _ 41 i • i .#..,.5 �t ' 1 , ...i....4:.$...14-1.1—t4-i. ' t = # F J.4.— i, ,--1-1.11 g a. -F f c F .�. ' .y • y i . r F s # i t i t -�.-o: x •., I - I. L. + ,+t j.- t ..f. 3 R e.,,�,7, .; . . r te > , A. •s }.. • 5 3 } �` ti(_�,,� S { Q t - ` f s S {. (y 1 F £- - r t .. ;. �-'. - ${ .°`. 4 7 F 7 .i 4 3' � '�' 4 ± .w.l �..; .. xL t 't .�.. 4 r # t at ,.....• .1 *1 fi t r € a # v t� Y � Xt€ f 7'y p # . F r te :' . ., x z , i '4. € .. t ' 8 ...4 '-- 1....'.- 1,...L. ) � . 4 � t 4 F i..,�. ,. g..•. 3 ' •a ' 3 x e- . d-- ! . • i F ..L.. . f 4. �^ ' 4 . 1 • f ° ! P f M S # M -•vr # • 1 .. • . • • • .. • • • .... 4421R • b 3 • • R • • R • • • • • e� • • • • • . ••■•• iii 2010 Googt 201 Tecinoiolies 25 52'39.35" N 80` W OFev iwe f SXStem i it rturer: 1 ' Product Approval Number: 07-,0015;/v Mlnknum Dato res It ... . �#ebte c+t'`atadons #: &Welton Design Pressure Product roved Specific System: Root S#: 12 Ridge Ventilation? S 0 Deck TYPO: fi f fedulagan; Mean Roof Helot 22 SI FLORIDA BUILDING CODE — RESIDENTIAL Fastener Typ &Spa cap: HIGH- VELOCITY NUR RCA lE ZONES • • . ••, •• • • • •• • • • (ASS 4 t c verI 15-44004 1),(4 paitsizebrio 31311 tit' • • •' • •:•..I • .:. •:• • i`r••.; •••• • • • •••• •,.wii •••• . ... • • • •, • • • •i • • • • ••••a•t_x •• ' f t . ' 4 6 S. ••••I; 44.24R HIGH - VELOCITY HURRICANE ZONES Simon � E l . : :. b ,. **1 C o K the *bin iinnodu lf':tll i -iral $ o f • vain* fbr ii tithe: atbe: t: d e r • • mil '. 1 x. ®. IA li/3, ell X 5: I I PraductApproval (Pi :''x .PBZ "` ' : _ , g ��566 ProductApprevaI sht � ;! �'•/ : C' ' /.�,f ffi��i �i � +ae 4. c5:6L Product Approval W. 19, 1 4444 2 "5ped1tili Bets': • Itiqutoodoninntntaititininin fsa *rom: C'a P crw duct Approval M,.. 41446 lace 0 .s4 ... p d : }o VS* C11 .:3. ;o Aridy 1 *. :ir 44146 r Fri H'th r er gar. than ••! 1, t ; ? • .v • enoit ' imistit" piste ` s B '1 12. " R• ,. ' +�• ° ProductAppro . `? 1 is "r..�, v. 4v¢ ,•_,..)~:Ws _._._ x Product '�.�" �%;� �.�: Approval x �s'_ � W _ )-Wit - ' � : l4 Product Approval .. • • . : : ;■;= rt NNW y MUM •1'112`. _ . ir RFAIA alr = L }.. �S� :, F .' P Drake .:FLORIDA WtILOINGI'CODE- RESIDENTIAL • • • • • MIAM CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION , NOTICE OF ACCEPTANCE (NOA) Entegra Sales, Inc. 819 S. Federal Highway, Suite 300 Stuart, FL 34994 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by Miami -Dade County Product Control Division and accepted by the Board of Rules and Appeals (BORA) to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Division (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve•tiCtMght to have this product or material tested for quality assurance purposes. If this product or materiel fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AJill o may hwi d ately revoke, modify, or suspend the use of such product or material within their jurisdiction. JQLA reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Divisio n•that this product or • material fails to meet the requirements of the applicable building code. • •••• This product is approved as described herein, and has been designed to comply with the Higf Alelocity Th i ic'tue Zone of the Florida Building Code. DESCRIPTION: Skandia Roof Tile This NOA renews NOA No. 00- 1106.03 and consists of pages 1 through 6. The submitted documentation was reviewed by Jor L. Nebo„ MIAMI -DADE COUNTY, FLORIDA METRO -DADE FLAGLER BUILDING 140 WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -2901 FAX (305) 375 -2908 •••• •••• • • • • • • • • • • • • • •• • •••• LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and • • following statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date. may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. NOA No.: 05- 0413.01 Expiration Date: 12/08/10 Approval Date: 12108/05 Page 1 of 6 • • • • • • • • • • • • • • ROOFING ASSEMBLY APPROVAL Category: Sub Category: Material: 2. PRODUCT DESCRIPTION Manufactured by Applicant Skandia. Skandia ABC Duratile USA "E" USA Trim Pieces Product Tile Nails Tile Screws Rainproof II Ice and Water Shield TU Underlayment Roofing Roofing Tiles Concrete 1. SCOPE This renews a roofing system using Entegra " Skandia" concrete roof tile, as manufactured for Entegra Sales, Inc. as described in Section 2 of this Notice of Acceptance. For the locations where the pressure requirements, as determined by applicable Building Code, does not exceed the values listed in section 4 herein. The attachment calculations shall be done as a moment based system. Dimensions Length: 16V" Width: 13" Length: varies Width: varies Thickness: varies 2.1 COMPONENTS OR PRODUCTS MANUFACTURED BY OTHERS Dimensions Min. 10dx 3" #8x 2V2" long 0.335" head dia. 0.131" shank dia. 0.175" screw thread dia. 30" x 75' roll 36" x 75' roll 60" x 75' roll 36" x 75' roll 39%8 "x32'10" roll Test Specifications Flat concrete roof tile fqr c1j j deck'tyr • ; TAS 112 batten nail -on. • • TAS 112 Test Specification s TAS 114 Appendix E TAS 114 Appendix E TAS 104 TAS 103 TAS 103 Product Description Corrosion resistant screw or smooth shank nails Corrosion resistant, coated, square drive, galvanized, coarse thread wood screws Single ply, nail -on underlayment with 2" self adhering top edge Self - adhering Underlayment Self-adhering Underlayment Product • •••• • Descriptlign• •••• .... •••• • .... • Accessory trim, concrett'iptf pieces far ; • . use at hips, rakes ridges'dnd'alley " • • terminations • • • • • • • • • .• • Manufacturer Generic (With current NOA) Generic (With current NOA) . • • •• •• Protect -O -Wrap, Inc. W.R. Grace Co. Polyglass USA, Inc. NOA No.: 05- 0413.01 Expiration Date: 12/08/10 Approval Date: 12/08/05 Page 2 of 6 Roof Tile Mortar ( "TileTiteTM") Roof Tile Mortar ( "Quickrete® Roof Tile Mortar #1140) Roof Tile Mortar (`BONSAL® Roof Tile Mortar Mix) Roof Tile Adhesive ( "Polypro® AH 160 ") Roof Tile Adhesive ( "Tile Bond ") Hurricane Clip & Fasteners N/A N/A N/A Various Factory premixed containers Clips Min. IA" width Min. 0.060" thick Clip Fasteners Min. 8d x 1 Vs" TAS 123 Prepared mortar mix designed for mortar set roof tile applications TAS 123 Prepared mortar mix designed for mortar set roof tile applications TAS 123 Prepared mortar mix designed for mortar set roof tile applications See NOA Two component polyurethane adhesives designed for adhesive set roof tile applications See NOA Single component polyurethane adhesives designed for adhesive set roof tile applications TAS 114 Appendix E Corrosion resistant clips with corrosion resistant nails 3. LIMITATIONS 3.1 Fire classification is not part of this acceptance. 3.2 For mortar or adhesive set tile applications, a static field uplift test in RAS 106 may required, refer to applicable building code. 3.3 Applicant shall retain the services of a Miami -Dade County Certified 4. INSTALLATION 4.1 "Entegra Sales Inc. Skandia Flat and its components shall be installed in strict compliance with Roofing Application Standard RAS 118,119, & 120 4.2 Data For Attachment Calculations Bermuda Roof Company, Inc. Quickrete Construction Products W.R. Bonsai Co. Polyfoam Products, Inc. Flexible Products ••.• • . Generic "" • wi$I currant ° AIDA) 00 . • •• •. • • . .... • • • •• • • • • • • •• • • . • • • • • 3ccc8 once With .. • •• • Laboratory to perform quarterly test in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Building Code Compliance Office for review. 3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed section 4.1 herein. 3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated otherwise by the underlayment material manufacturers published literature. 3.6 This acceptance is for wood deck applications Minimum deck requirements shall be in compliance with applicable building code. NOA No.: 05- 0413.01 Expiration Date: 12/08/10 Approval Date: 12108/05 Page 3 of 6 • . • • • • • • • • • • • • • • • • •• Table 3: Attachment Resistance Expressed as a Moment - Mf (ft -Ibf) For Nail -On Systems Tile Fastener Type Direct Deck plywood) Direct Deck plywood).. • Battens . : .... • • • Skandia 2 -10d Ring Shank Nails 30.9 38.1 •••:, • 17.2. 1 -10d Smooth or Screw Shank Nail 7.3 9.8 •••• • 4.9••. • 2 -10d Smooth or Screw Shank Nails 14.0 18.8 . • • •' : 7,4•:•. • • • 1 #8 Screw 30.8 30.8 : •':' : 18.2 • 2 #8 Screw 51.7 51.7 ; , - 244• • : • 1 -10d Smooth or Screw Shank Nail (Field Clip) 24.3 24.3 • .. • : 24.2.. • • • • .. • 1 -10d Smooth or Screw Shank Nail (Eave Clip) 19.0 19.0 22.1 2-10d Smooth or Screw Shank Nails (Field Clip) 35.5 35.5 34.8 2 -10d Smooth or Screw Shank Nails (Eave Clip) 31.9 31.9 32.2 2 -10d Ring Shank Nails' 50.3 65.5 48.3 1 Installation with a 4° tile headfap and fasteners are located a minimum of 2'h" from the head of tile. Table 4: Attachment Resistance Expressed as a Moment Mf (ft -Ibf) For Two Pa Adhesive Set S stems Tile Profile Tile Application Minimum Attachment Resistance Skandia Adhesive 31.3 2 See manufactures component approval for installation requirements. 3 Flexible Products Company TfleBond Average weights per patty 13.9 grams. Polyfoam Product, Inc. Average weight per patty 8 grams. Table 2: Restoring Moments due to Gravity - Mg (ft-Ibf) Tile Profile 3 ":12" 4 ":12" 5 ":12" 6 ": 12" 7 ":12 greater Battens "Or Direct Deck Battens Direct Deck Battens Direct Battens Direct Deck Battens Direct Deck Entegra Skandia 6.85 7.79 6.75 7.67 ' 6.61 7.52 6.44 7.32 6.26 N/A NOA No.: 05- 0413.01 Expiration Date: 12/08/10 Approval Date: 12/08/05 Page 4 of 6 Table 1: Aerodynamic Multipliers - ?. (ft Tile Profile a , ( ) Batten Application Direct a , ( ) p tion Skandia 0.267 0.289 NOA No.: 05- 0413.01 Expiration Date: 12/08/10 Approval Date: 12/08/05 Page 4 of 6 Table 4A: Attachment Resistance Expressed as a Moment - Mf (ft -ibf) For Single Patty Adhesive Set Systems Tile Profile Tile Application Minimum Attachment Resistance Skandia Poly ProTM a PolyProTM 40.4 4 Large paddy placement of 45 grams of PolyProTM. Medium paddy placement of 24 grams of PolyProm. Table 4B: Attachment Resistance Expressed as a Moment - Mt (ft-Ibf) for Mortar Set Systems Tile Profile Tile Application See specific mortar manufacturer's Notice of Acceptance. Attachment Resistance 5. LABELING .... • • 5.1 All tiles shall bear the imprint or identifiable marking of the manufactiZrerc'name • or .8 . or following statement: "Miami -Dade County Product Control Approved • : • • • • • • • 5.2 Entegra Sales Inc., Skandia Roof Tile bears the following markings; 1 dia, Skanilia ABC, Duratile, USA "E" USA, where the E is a stylized logo. •••• • • • • • • 6. BUILDING PERMIT REQUIREMENTS • • • • • 6.1 Application for building permit shall be accompanied by copies of the fdfodrtng: � ' • • • • 6.1.1 This Notice of Acceptance. : . : • • 6.1.2 Any other documents required by the Building Official or applicable J3uildin; Code in order to properly evaluate the installation of this systent • • ; • • • • • • 7. MANUFACTURING LOCATIONS 7.1 Indiantown, FL NOA No.: 05-0413.01 Expiration Date: 12/08/10 Approval Date: 12/08/05 Page 5 of 6 • • • • • • PROFILE DRAWING SKANDIA FLAT CONCRETE TILE 2 4 SKANDIA END OF THIS ACCEPTANCE • • ••• • • • • •• • • •••• • • •••• •••• • • • • • • 831•••• •••• • • • • to •• •• •• • NOA No.: 05- 0413.01 Expiration Date: 12108110 Approval Date: 12/08/05 Page 6 of 6 • • • • • • • • • • • • • • • • • • •• • •••• • • • • MIAMIDADE BUILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION NOTICE OF ACCEPTANCE (NOA) Polyglass USA Inc. 150 Lyon Drive Fernley, NV 89408 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by Miami -Dade County Product Control Division and accepted by the Board of Rules and Appeals (BORA) to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County rrotkrq Control Division (In Miami Dade County) and/or the AHJ (in areas other than Mianmi•Pade C8drIty) reserve the right to have this product or material tested for quality assurance purpose's'If this prodLc'ol material fails to perform in the accepted manner, the manufacturer will incur the ex grlsmf such testing and the AHJ may immediately revoke, modify, or suspend the use of such product,Qr Imaterial their jurisdiction. BORA reserves the right to revoke this acceptance, if it is deterin?rpad,b) Miari'Ur 1 County Product Control Division that this product or material fails to meet the •retirements of the applicable building code. • • • • • • • • This product is approved as described herein, and has been designed to comply with the ! k rida Building Code and the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Polystick P, Basik, IR/mX, TU ,1 Pl : TU Polyester and Mt .enti • LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved ", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA No. 06- 0505.01 and consists of pages 1 throu: ' 6. The submitted documentation was reviewed by Jorge L. Acebo. MIAMI -DADE COUNTY, FLORIDA METRO -DADE FLAGLER BUILDING 140 WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -2901 FAX (305) 375 -2908 • • • • • • NOA No.: 07- 1025.10 Expiration Date: 09/13/11 Approval Date: 04 /10/08 Page 1 of 6 ROOFING COMPONENT APPROVAL Category: Sub - Category: Material: PRODUCTS DESCRIPTION: Product Polystick P underlayment Polystick Basik underlayment Polystick IR/IRX underlayment Polystick TU underlayment Polystick TU Plus underlayment (Facer of Membrane Labeled in Orange or Black Ink) Polystick TU Polyester Polystick MU underlayment Test Dimensions Specification Roll: 75' x 3' 40 mils thick Roll: 65'8"x3'3- 60 mils thick Roll: 65'8" x 3'3 - / 80 mils thick Roll: 32' 10" x 3'3 100 mils thick Roll: 65'8" x 3'3 80 mils thick Roll: 32'10" x 3'3 -3/8" 130 mils thick Roll: 65'8" x 3'3 80 mils thick Roofing Underlayment SBS , APP Self - Adhering Modified Bitumen ASTM D 1970 A polyethylene top surface, self- adhering, SBS polymer modified bituminous sheet material for use as an underlayment in sloped roof assemblies. Designed as an ice & rain shield. ASTM D 1970 A homogeneous, rubberized asphalt waterproofing membrane, glass fiber reitinfees1 with polyolefinic film on tit • upper surface ti use an underlayment for m aJ jppfing. • • • • TAS 103 and A fine granular /sand top sur€aaoself- adhering, ASTM D 1970 APP polymer modified, filetghs§ reintitur11. bituminous sheet material f&'i? as an • • • • underlayment in sloped rodf Ls fnblies. • •: • • Designed as an ice & rain s'liiefd and as Pitt r of tile tderlayment. TAS 103 and ASTM D 1970 TAS 103 and ASTM D 1970 TAS 103 TAS 103 and ASTM D 1970 Product Description • •. • A heavy granuled surface %elf adhering, AW polymer modified, fiberglass br polyester • • • • reinforced, bituminous sheet material fonts as an underlayment in sloped roof assemblies. Designed as a a roof tile underlayment. A non - wicking fabric surfaced, self - adhering, APP polymer modified, fiberglass reinforced with a high strength polyester fabric, bituminous sheet material for use an an underlayment in sloped roof assemblies. Designed as a metal roofing and roof tile underlayment. A rubberized asphalt waterproofing membrane, glass- fiber /polyester reinforced, with a granular surface designed for use as a tile roof underlayment. A non - wicking fabric surfaced, self - adhering, APP polymer modified, fiberglass reinforced, bituminous sheet material for use an an underlayment in sloped roof assemblies. Designed as a metal roofing and roof tile underlayment. NOA No.: 07- 1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 2 of 6 EVIDENCE SUBMITTED: Test Agency Test Identifier Test Name/Renort Date Exterior Research & Design, LLC #11756.04.01 -1 TAS 103 04/27/01 #11756.08.01 -1 ASTM D 1970 08/14/01 #02202.08.05 TAS 103 08/29/05 Trinity I ERD #P5110.08.07 TAS 103 08/29/07 PRI Asphalt Technologies PRI01111 ASTM D 4977 04/08/02 PUSA-005 -02 -01 ASTM D 4977 01/31/02 PUSA -018 -02 -01 ASTM D 2523 07/14/03 PUSA -035 -02 -01 TAS 103 09/29/06 PUSA -033 -02 -01 ASTM D 1970 01/12/06 Momentum Technologies, Inc. JX20H7A ASTM D 4798 04/01/08 ASTM G 155 INSTALLATION PROCEDURES: Deck Type 1: Wood, non - insulated, new construction Base Sheet: One or more plies of ASTM D 226 Type II or ASTM D 2626 or Polyprotector UDj, p; • • Polyprotector UDL AS. • • • • • Fastening: Nails and tin caps 12" grid, 6" o.c. at laps. (for base sheet only) • ' • Membrane: Polystick membranes self - adhered. •••••• • • • • • • Surfacing: None •••• • • ° • panels, and sweep the deck thoroughly to remove any dust and debris prior to apptitat,ion. • • 1. All nails in the deck shall be carefully checked for protruding heads. Re- fasterparyMoose decking • • • • • 2. Place the underlayment over metal drip edge in accordance with RAS 111. 3. Place the first course of membrane parallel to the eave, rolling the membrane to bbtaii maxi Ptti• • contact. Remove the release film as the membrane is applied. . All side laps shall be a minirM& of 3-'/s" and end laps shall be a minimum of 6." Roll the membrane into place after removing the release strip. Vertical strapping of the roof with Polystick is acceptable. Membrane shall be back nailed in accordance with applicable building code. 4. When applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane from the center outward in both directions. 5. For ridge applications, center the membrane and roll from the center outward in both directions. 6. Roll or broom the entire membrane surface so as to have full contact with the surface, giving special attention to lap areas. 7. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control Notice of Acceptance. 8. All protrusions or drains shall be initially taped with a 6" piece of underlaynent. The flashing tape shall be pressed in place and formed around the protrusion to ensure a tight fit. A second layer of Polystick shall be applied over the underlayment. NOA No.: 07-1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 3 of 6 Tile Profile Polystick IR/IRX Polystick MU Pol ,TU, TUB 71J•Eillyeste?r• • • • • •Nrlimitation• • • • •No •ltmitation• • • • Flat Tile 5:12 No limitation Profiled Tile Prohibited 5:12 GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance. 2. Polystick P, Basik and IR/1RX may be used in asphaltic shingles, wood shakes and shingles, non- structural metal roofing, and quarry slate roof assemblies. Polystick P and Basik shall not be used as roof tile underlayment. 3. Deck requirements shall be in compliance with applicable building code. 4. Polystick membranes shall be applied to a smooth, clean and dry surface. The deck shall be free of irregularities. 5. Polystick membranes shall not be adhered directly over a pre - existing roof membrane as a recover system. 6. Polystick P, Basik, IR/IRX TU, TU Polyester and MU Underlayments shall not be left exposed as a temporary roof for longer than 30 days after application. Polystick TU Plus shall not be left exposed as a temporary roof for longer than 180 days after application. Polyglass reserves the right to revise or alter product exposure times; not to exceed the preceeding maximum time limitations. 7. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 9B -72 of the Florida Administrative Code. 8. In roof tile application, data for the attachment resistance of roof tiles shall be as set forth in the roof the manufacturer's Notice. Polystick TU, TU Plus and MU may be used in both adhesive set and mechanically fastened roof tile applications. Polystick IR/MX is limited to mechanically fastened roof tile applications. Polystick TU Polyester may be used in both adhesive set and • • • . • mechanically fastened roof tile applications with the exception of mortar set tilt apgkcations •T maximum roof slope for use as roof tile underlayment for (direct -to -deck) tile assemblies shoji by • as described below: 6 Roofing Tiles (6 Max. Per Stack) 12 • • • • . • NOA No.: 07- 1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 4 of 6 •. • • • • • • • e above slope limitations can be exceeded only by using battens and counter battens in accordance ' • with the Approved Tile System Notice of Acceptance and applicable Florida Building,Codg requirements. • 9. Care should be taken during the loading procedure to keep foot traffic to a minimum and to avoid • • dropping of tile directly on the underlayment. Refer to Polyglass Tile loading detail for loading procedure. GENERAL LIMITATTIONS: (CONTINUED) 10. Refer to prepared roofmg system Product Control Notice of Acceptance for listed approval of this product with specific prepared roofing products. Polystick P, Basik, IR/IRX, TU, TU Plus, TU Polyester & MU may be used with any approved roof covering Notice of Acceptance listing Polystick P, Basik, IR/1RX, TU, TU Plus, TU Polyester & MU as a component part of an assembly in the Notice of Acceptance. If Polystick P, Basik, IR/1RX, TU, TU Plus, TU Polyester & MU is not listed, a request may be made to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control Department for approval provided that appropriate documentation is provided to detail compatibility of the products, wind uplift resistance, and fire testing results. LABELING: 1. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo and the following statement: "Miami -Dade County Product Control Approved" or the Miami -Dade County Product Control Seal as shown below. BUILDING PERMIT REQUIREMENTS: Application for building permit shall be accompanied by copies of the following: 1. This Notice of Acceptance. .. • • • • •••• • • . . • •• • • •. • • • • • • • .. • 2. Any other documents required by the Building Official or applicable building code t Mi er to prore evaluate the installation of this materials. • • •••• POLYGLASS GENERAL APPLICATION GUIDELINES FOR POLYSTICK MEMBRAI:.. • ..' 1. Polyglass does accept the direct application of Polystick underlayment membratps to vg ood decks., Installers are cautioned to refer to applicable local building codes prior to direct,deckinstalla6.5h "' • to ensure this is acceptable. Please also refer to applicable Product Data Sheets c€tl e : •••• • corresponding products. •••• • 2. All rolls, with the exception of Polystick TU Plus and Polystick MU should be back-nailed in selvage edge seam as per Polyglass Back Nailing Guide. Nails shall be, 11 gauge ring shank type, applied with a minimum 1" metal disk as required in Dade County or simplex type nail as otherwise allowable in other regions, at a minimum rate of 12" o.c. Polystick TU Plus and Polystick MU should be back nailed in designated area marked "nail area, area para clavar" on the face of membrane, with the above stated nails and/or disks. The head lap membrane is to cover the area being back - nailed. (Please refer to applicable local building codes prior to installation.) 3. All seal lap seams (selvage laps) must be rolled with a hand roller to ensure full contact. 4. All fabric over fabric; and granule over granule end laps, shall have a 6" wide, uniform layer of Polyglass Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, Polyglass PG500 MB Flashing Cement, Mule -Hide 241 Premium Modified Plashing Cement, Mule -Hide 251 Premium Wet/Dry Elastomeric Flashing Cement, or Mule -Hide 421 Mod Bit Flashing Adhesive Trowel Grade mastic, applied in between the application of the lap. The use of mastic between the laps does not apply to Polystick Basik. 5. A maximum of 6 tiles per stack are allowed when loading tile on the underlayments. Refer to the Polyglass Tile Loading Guidelines. NOA No.: 07 1025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 5 of 6 • • • • • • • 6. Battens and/or Counter- battens, as required by the tile manufacturers NOA' s, must be used on all projects for pitch/slopes of T' /12" or greater. It is suggested that on pitch/slopes in excess of 6 1 /a "/12 ", precautions should be taken, such as the use of battens to prevent tile sliding during the Ioading process. 7. Minimum cure time after membrane installation & before loading of roofing tiles is Forty Eight (48) Hours. 8. Polystick TU Plus, Polystick MU may not be used in any exposed application such as crickets, exposed valleys, or exposed roof to wall details. 9. Repair of Polystick membranes is to be accomplished by applying Polyglass Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, Polyglass PG500 MB Flashing Cement, Mule -Hide 241 Premium Modified Flashing Cement, Mule -Hide 251 Premium Wet /Dry Elastomeric Flashing Cement, or Mule -Hide 421 Mod Bit Flashing Adhesive Trowel Grade mastic to the area in need of repair, followed by a patch of the Polystick material of like kind should be set and hand rolled in place over the area needing such repair. Patching membrane shall be a minimum of 6 inches in either direction. The repair should be installed in such a way so that water will run parallel to or over the top of all laps of the patch. 10. All self- adhered membranes must be rolled to ensure full contact with approved substrates. Polyglass requires a minimum of 40 lbs for a weighted roller for the rolling of the field membrane. Hand rollers are acceptable for rolling of patches or small areas of the roof. 11. All approved substrates should be dry, clean and properly prepared, before any:application of• ••• Polystick membranes commences. An approved substrate technical bulletin can Abe furnishe4 up x request. It is recommended to refer to applicable building codes prior to installfttd4 td verify • • • acceptable substrates. • 12. The Polyglass Miami -Dade Notice of Acceptance (NOA) approval for Polystick►mbranes and. • PolyProtector UDL can be furnished upon request by our Technical Services Departautent by ••:.. calling 1 (800) 894 -4563. 13. Polyglass offers • a 10 year Limited Material Warranty on all properly installed $olyttiCk self ° • adhered underlayments. Warranty must be requested and registered by Polyglass to be in face. 14. Questions in regards to the application of Polyglass products should be directed re our Techui'c' • Services Department at 1(800) 894 -4563. ° ° a1 ° 15. Polyglass recommends that applicators follow good roofing practices and applicable procedures as outlined by the National Roofing Contractors Association (NRCA). PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC APPLICATIONS. LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS. END OF THIS ACCEPTANCE •••• • NOA No.: 074025.10 Expiration Date: 09/13/11 Approval Date: 04/10/08 Page 6 of 6 M1AMI�DADE BUILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION NOTICE OF ACCEPTANCE, (NOA) Polyfoam Products, Inc. 11715 Boudreaux Road Tomball, TX 77375 MIAMI -DADE COUNTY, FLORIDA METRO -DADE FLAGLER BUILDING 140 WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130 -1563 (305) 375 -2901 FAX (305) 375 -2908 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed by the BCCO and accepted by the Building Code and Product Review Committee to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The BCCO (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BCCO reserves the right to revoke this acceptance, if it is determined by BCCO that this product or material fails to meet the requirements of the applicable building code. • "' • • • • •••• This product is approved as described herein, and has been designed to comply with the High Velocity„Hu>xtc;ane Zone of the Florida Building Code. • DESCRIPTION: Polypro® A11160 • • .... .... . . •••• •••• RENEWAL of this NOA shall be considered after a renewal application has been filed and :here has keettrica change in the applicable building code negatively affecting the performance of this product' • • • • • • • • • • • been a fevision or camp to the as an emlors&nent ofanv this NOA. Failure to %rawly TERMINATION of this NOA will occur after the expiration date or if there has materials, use, and/or manufacture of the product or process. Misuse of this NOA product, for sales, advertising or any other purposes shall automatically terminate with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA No.01- 0521.02 and consists of pages 1 through 7 The submitted documentation was reviewed by JR rge L. Acebo. NOA No.: 06- 0201.02 Expiration Date: 05/10/11 ,.,Approval Date: 04/13/06 Page 1 of 7 • ROOFING ASSEMBLY APPROVAL: Category: Roofing Sub Category: Roof tile adhesive Materials: Polyurethane SCOPE: This approves Polypro® AH160 as manufactured by Polyfoam Products, Inc. as described in Section 2 of this Notice of Acceptance. For the locations where the design pressure requirements, as determined by applicable building code, does not exceed the design pressure values obtained by calculations in compliance with Roofing Application Standard RAS 127, for use with approved flat, low, and high profile roof tiles system using Polypro® AH 160. Where the attachment calculations are done as a moment based system for single patty placement, and as an uplift based system for double patty systems PRODUCTS MANUFACTURED BY APPLICANT: Product Dimensions Polypro® AH160 N/A Foampro® RTF1000 N/A ProPack® 30 & 100 N/A PRODUCTS MANUFACTURED BY OTHERS: PHYSICAL PROPERTIES: Property Density Compressive Strength Tensile Strength Water Absorption Moisture Vapor Transmission Dimensional Stability Closed Cell Content Test Specifications TAS 101 Test ASTM D 1622 ASTM D 1621 ASTM D 1623 ASTM D 2127 ASTM E 96 ASTM D 2126 ASTM D 2856 Product Description Two component polyurethane foam adhesive Dispensing Equipment Dispensing Equipment • • Any Miami -Dade County Product Control Accepted Roof Tile Assembly having a curfaia•OA wluela..' list moment resistance values with the use of Polypro AH160 roof tile adhesive. ..•• • • • • • • Results • ..' 1.6 lbs. /ft.' 18 PSI Parallel to rise 12 PSI Perpendicular to rise 28 PSI Parallel to rise 0.08 Lbs./Ft 3.1 Perm / Inch +0.07% Volume Change @ -40 F., 2 weeks +6.0% Volume Change @158°F., 100% Humidity, 2 weeks 86% .•. • • • • .... .... .. • • • • • .... .... Note: The physical properties listed above are presented as typical average values as determined by accepted ASTM test methods and are subject to normal manufacturing variation. NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04/13/06 Page 2 of 7 EVIDENCE SUBMITTED; Test Agency Center for Applied Engineering Miles Laboratories Polymers Division Ramtech Laboratories, Inc. Southwest Research Institute Trinity Engineering Celotex Corp. Testing Services LIMITATIONS: 1. • • • • .. Fire classification is not part of this acceptance. Refer to the Prepared Roof Tile Assembly for Fire.. rating. 2. Polypro® AI1160 shall solely be used with flat, low, & high tile profiles. 3. Minimum underlayment shall be in compliance with the Roofing Application Standard RAS 120. 4. Roof Tile manufactures acquiring acceptance for the use of Polypro their tile assemblies shall test in accordance with TAS 101. 5. Roof Tile manufactures acquiring acceptance for the use of HANDI -STICK roof tile adhesive with their tile assemblies shall test in accordance with TAS 101 with section 10.4 as modified herein. I F S : 2 F MS Test Identifier #94 -060 257818 -1PA 25- 7438 -3 25- 7438 -4 25- 7438 -7 25 -7492 NB -589 -631 9637 -92 01- 6743 -011 01- 6739- 062b[1] 7050.02.96 -1 528454 -2 -1 528454 -9 -1 528454 -10 -1 520109 -1 520109 -2 520109 -3 520109 -6 520109 -7 520191 -1 520109 -2 -1 W Test Name/Report TAS 101 'TAS 101 SSTD 11 -93 SSTD 11 -93 SSTD 11 -93 ASTM D 1623 ASTM E 108 ASTM E 108 ASTM E 84 TAS 114 TAS 101 TAS 101 TAS 101 • Date 04/08/94 12/16/96 10/25/95 11/02/95 12/12/95 02/01/94 04/30/93 11/16/94 01/16/95 03/14/96 10/23/98 .... • • .72/28/98" .. • • ..• • • .. • • .... .. • • • .... .. .. .... A3/02/99.. • . • • • .. .. .. .. • • • • • • • AH160 roof tile adhesive with NOA No.: 06-0201.02 Expiration Date: 05/10/11 Approval Date: 04/13/06 Page 3 of 7 Table 1: Adhesive Placement For Each Generic Tile Profile. • • • • - • Tile Profile Placement Detail Single Paddy Weight Min. (grams) Two Paddy IlVeight per pltdcbp j 4in. • • (gf'drns) .• N/A —` Flat, Low, High Profiles #1 35 High Profile (2 Piece Barrel) #1 17 /side on cap and 34 /pan N/A Flat, Low, High Profiles #2 24 N/A Flat, Low, High Profiles #3 8 INSTALLATION: 1. Polypro® AH160 may be used with any roof tile assembly having a current NOA that lists uplift resistance values with the use of Polypro® AH160. 2. Polypro'i A11160 shall be applied in compliance with the Component Application section and the corresponding Placement Details noted herein. The roof tile assembly's adhesive attachment with the use of Polyproe AH160 shall provide sufficient attachment resistance, expressed as an uplift based system, to meet or exceed the uplift resistance determined in compliance with Miami -Dade County Roofing Application Standards RAS 127. The adhesive attachment data is noted in the roof tile assembly NOA 3. Polypro® AH160 roof the adhesive and its components shall be installed in accordance with Roofmg Application Standard RAS 120, and Polyfoam Products, Inc. Polypro® AH160 Operating Instruction and Maintenance Booklet. 4. Installation must be by a Factory Trained 'Qualified Applicator' approved and licensed by PoIyfoam Products, Inc. Polyfoam Products Inc. shall supply a list of approved applicators to the authority having jurisdiction. 5. Calibration of the Foampro® dispensing equipment is required before application of any adhesive. The mix ratio between the "A" component and the "B" component shall be maintained between 1.0- 1.15 (A): 1.0 (B). The dispense timer shall be set to deliver 0.0175 to 0.15 pounds per tile as determined at calibration. No other settings shall be approved. 6. Polypro® AH160 shall be applied with Foampro RTF1000 or ProPack® 30 & 100 dispensing equipment only. •••• 7. Polypro® AH160 shall not be exposed permanently to sunlight. � . • •• • 8. Tiles must be adhered in freshly applied adhesive. Tile must be set within 2 to 3 minutes after • • • Polypro® AH160 has been dispensed. • ' 9. Polypro® AH160 placement and minimum patty weight shall be in accordance with] • Details' herein. Each generic tile profile requires the specific placement noted hergip.. • • • LABELING: All Polypro® AH160 containers shall comply with the Standard Conditions listed herein. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or applicable building code in order to properly evaluate the installation of this system. •. • • •• • • • • •. • •• • NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04 /13/06 Page 4 of 7 Nail tuough plastic cement Underlarnent EaveCoar 10 tn. Ease coarse only Keep adhesive approx. 4 In. up from modeles ADHESIVE PLACEMENT DETAIL 1 SINGLE PATTY Fascia Ems Chore 11 Pleee enough adhesive toaddeva1Tto23 mod214'stor square Inches In contact with the pan tile Ste" Pitch aPPLicaftims 2) Turn e upsidedown. c Mle. Then install the 4* • e top portion of the save course covaUle. Abut to second course of pan tiles. Ensure ease and of pan and cover tiles are flush at ease fine. Eave (mater shown) Weaphole Fascia Nab through plastic cement •••• • • • •••• • • • ••• • • • •• • • ••• Sheathing •••• • Optiornal•••• Pohdup Mortar on longimdhml edges of file • NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04 /13/06 Page 5 of 7 1 / i ADHESIVE PLACEMENT DETAIL 2 SINGLE PATTY •••• • • •••• • • • ... • •• • • • • • •• •• • • • NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04 /13/06 Page 6 of 7 • • • • • • • • • • • • • • • • • • • • • • • • • • • •• • •••• • • • • Nail through plastic cement 1 in. x3ln. Single paddy on underiayment Single paddy on top of the ADHESIVE PLACEMENT DETAIL 3 DOUBLE PATTY Eave Course Nail through plastic cemen Underlayment *} in.x 3 in. S 41n. paddy on under layment Single paddy on top of tile Ens Course Single paddy under the Single paddy between tite 21n. x 7 fn. medium she paddy eave course only • • - 11.11 - • Fascia Weephole 1111•• ar. • t •Dr dse • • • Single paddy between tile Eave Closure 2 In. x 7 In. medium Fasd � paddy save course only END OF THIS ACCEPTANCE • •••• • 00.41 • • • • •••• 80•0 0410• • • • • • .• 00 •. • • • • • • • • • • • • • • • • • • •• • 0000 • • •00• NOA No.: 06- 0201.02 Expiration Date: 05/10/11 Approval Date: 04/13/06 Page 7 of 7 • • • • • • • • • 1524.1 As it pertains to this section, it is the responsibility of the roofing contractor to provide the owner with the required roofing permit, and to explain to the owner the content of this section.. The provisions of Chapter 15 of the Florida Building Code, Building govem the minimum requirements and standards of the industry for roofing system installations. Additionally, the following items should be addressed as part of the agreement between the own: a d the contractor. The owner's initial in the adjacent box indicates that the item has been explained. 1. Aesthetics Workmanship: The workmanship provisions of Chapter 15 (High Velocity Hurricane Zone) are for the purpose of providing that the roofing system meets the wind resistance and water intrusion performance standards. Aesthetics (appearance) issues are not a consideration with respect to workmanship provisions. Aesthetic issues such as color or architectural appearance, that are not part of a zoning code, should be addressed as part of the agreement between the owner and the contractor. 2 . Renalling Wood Decks: When replacing roofing, the existing wood roof deck may have to be renailed in accordance with the current provisions of Chapter 16 (High Velocity Hurricane Zones) of the Florida Building Code. (The roof deck is usually concealed prior to removing the existing roof system). 3. Common Roofs: Common roofs are those which have no visible delineation between neighboring units (i.e. townhouses, condominiums, etc.). In buildings with common roofs, the roofing contractor and/or owner should notify the occupants of adjacent units of roofing work to be performed. 4. Exposed Ceilings: Exposed, open beam ceilings are where the underside oZ the ?oof decltfti 'can be • viewed from below. The owner may wish to maintain the architectural appearance,iherrfore, loo r nail '• penetrations of the underside of the decking may not be acceptable. The Florida Buldi? 'Code • pr the option of maintaining this appearance. "' " ' • ' 5. Ponding Water: The current roof system and /or deck of the building may :of drain weTl may . • cause water to pond (accumulate) in low -lying areas of the roof. Ponding can be an ri ation o� 9Vuctural distress and may require the review of a professional structural engineer. Pondiri� may shorten the life expectancy and performance of the new roofing system. Ponding conditions may not bet evictor until the original • roofing system is removed. Ponding conditions should be corrected. • • • 6 Overflow scuppers (wall outlets): It is required that rainwater flow off so that the• roof 4s not • overloaded from a build up of water. Perimeter /edge walls or other roof extensions may block this discharge if overflow scuppers (wall outlets) are not provided. It may be necessary to install overflow scuppers in accordance with the Florida Building Code, Plumbing. E Most roof structures should have some ability to vent natural airflow through the interior of the structural assembly (the building itself). The existing amount of attic ventilation shall not be reduced. It may be beneficial to consider additional venting which can result in exte Aging the service life of the roof. y e SECTION 1524 HIGH VELOCITY HURRICANE ZONES REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIONS Owner's Agent's Sr 11300 NW 2ND AVE MIAMI SHORES Property Address Permit Number Rev:1/20/2005,Computer Services, Building Department •••• •••• • • • • • • • • 0 / OS /Zo)O Date Co actor's Signature ••••