RF-19-1296Miami Shores Village
10050 NE 2 Ave
Miami Shores FL 33138
305-795-2204
_nh
Issue Date: 06/07/2019
Location Address Parcel Number
134 NW 94TH ST, Miami Shores, FL 33150 1131010330760
Contacts
Permit NO.: RF-06-19-1296
Permit Type: Roof
Work Classification: Tile
Permit Status: Approved
Expiration: 12/04/2019
MARI ARISTIZABAL Owner PRECISION ROOFING CORP Contractor
134 NW 94 ST, MIAMI SHORES, FL 33138 JOANNA TALLET
12410 SW 18 ST, MIRAMAR, FL 33027
Business: 3058229969 11
Inspection Description: RE -ROOF TILE TO TILES Valuation: $ 20,500.00 Inspection Requests:
4949
Total Scl Feet: 2,400.00
Fees
Amount
Application Fee - Other
$50.00
CCF
$12.60
DBPR Fee
$4.50
DCA Fee
$3.00
Education Surcharge
$4.20
Roofing Fee
$250.00
Scanning Fee
$12.00
Technology Fee
$7.50
Total:
$343.80
Building Department Copy
Payments
Date Paid Amt Paid
Total Fees
$343.80
Check # 38139
06/07/2019 $343.80
Amount Due:
$0.00
In consideration of the issuance to me of this permit, I agree to perform the work covered hereunder in compliance with all ordinances and regulations
pertaining thereto and in strict conformity with the plans, drawings, statements or specifications submitted to the proper authorities of Miami Shores
Village. In accepting this permit I assume responsibility for all work done by either myself, my agent, servants, or employes. I understand that separate
permits are required for ELECTRICAL, PLUMBING, MECHANICAL, WINDOWS, DOORS, ROOFING and SWIMMING POOL work.
OWNERS AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws
regulating construction and zoning. Futhermore, I authorize the above named contractor to do the work stated.
Authorized Signature: Owner
/ Applicant / Contractor _T_Agent
Date
June 07, 2019 Page 2 of 2
gECEIVED
Miami Shores Village
r�
Building Department
10050 N.E.2nd Avenue, Miami Shores, Florida 33138
Tel: (305) 795-2204 Fax: (305) 756-8972
INSPECTION LINE PHONE NUMBER: (305) 762-4949
BUILDING
PERMIT APPLICATION
❑ BUILDING ❑ ELECTRIC ❑■ ROOFING
JU 0 6 Z019
BY:
FBC 20 I _I.
Master Permit No.1� - 66 M —12
Sub Permit No.
❑ REVISION ❑ EXTENSION ❑RENEWAL
❑PLUMBING ❑ MECHANICAL [:]PUBLICWORKS ❑ CHANGE OF ❑ CANCELLATION ❑ SHOP
CONTRACTOR DRAWINGS
JOB ADDRESS: 17 _I N W " 1 1 S X�
City: Miami Shores
County:
Miami Dade
Zip: S .5 1 1 CJ
Folio/Parcel#: It — 31 Q ( —_() n
^ o ^% (0 D
Is the Building Historically Designated: Yes NO
Occupancy Type: Load:
Construction Type: ADO F Flood Zon
BFE: FFE:
OWNER: Name (Fee Simple Titleholder):
N�C1fT 1 �-
! `�t�7��
Phone#: ZY6).DS—SO08
I/ 437—
Address: a/'; A A4 / '9'7
City: M I �>W E; t� State: 47-o/L1/2y Zip: 33 I
Tenant/Lessee Name: Phone#:
Email
CONTRACTOR: Company Name: Pjt4OV5 to �OOIJ� �,"r Phone
Address: a b q (o W —7- P L- i
City:
Qual
_Zip:W��3> I b
+ ne)80 Z
/
State Certification or Registration #: C e � 2 1 7Z� (O 3 Certificate of Competency #: ll,�
DESIGNER: Architect/Engineer: Phone#:
Address: City: State: Zip:
Value of Work for this Permit: $ '0 J CJl / Square/Linear Footage of Work: 02 Y O C0
Type of Work: ❑ Addition ❑ Alteration ❑ New Rep ' Replace ❑ Demolition
Description of Work:
(l.E -Pow' -me3 Tt) Ti LES .
Specify color of color thru tile:
Submittal Fee $
Scanning Fee $
Permit Fee $
Radon Fee $
Technology Fee $ Training/Education Fee $
Structural Reviews $,
CCF $ CO/CC $
DBPR $
Notary $
Double Fee $
Bond $ �I co
TOTAL FEE NOW DUE $ 343 -
(Revised02/24/2014) G3
Bonding Company's Name (if applicable)
Bonding Company's Address
City
State
Mortgage Lender's Name (if applicable)
Mortgage Lender's Address
City
State
Zip
Zip
Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has
commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating
construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRIC, PLUMBING, SIGNS, POOLS,
FURNACES, BOILERS, HEATERS, TANKS, AIR CONDITIONERS, ETC.....
OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all
applicable laws regulating construction and zoning.
"WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY
RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND
TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING
YOUR NOTICE OF COMMENCEMENT."
Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must
promise in good faith that a copy of the notice of commencement and construction lien law brochure will be delivered to the person
whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site
for the first inspection which urs seven (7) days after the building permit is issued. In the absence of such posted notice, the
inspection will not be approvqld p reinspection fee will be charged.
or AGENT
The foregoing instrument was acknowledged before me this
("I day of f4f> q A 20 tel by
( who is personally known to
me or who has produced
as
Signature
_�J�r
() CONTRACTOR
The foregoing instrument was acknowledged before me this
day oJW
20 J ' by
a l�Q wo'k- who is personally known to
me or who has produced as
identification and who did take an oath.
identification and who did take an oath.
NOTARY PUBLIC:
NOTARY PUBLIC:
Sign:
Sign:
✓r�S �
��,
jj
r�03/A4� -
Print:
Print:iw
V
Seal:
�.'� ,., CARLOS At a of
Notary Public • State of Florida
Seal:
;y. �, •..
""' CARLOS A URBINA
r'f!��'' Notary Public
r r ' Commission < GG 329383
My Comm. Expires Jul 31, 2023
- State o(JFlorida
?�,o jj Commission ; GG 329
Nadanal Notary Assn.
•
r n,::' My Comm. Expires Jul 3thrpuq'r•
Sonded through National Nota
APPROVED BY
W q Plans Examiner
Zoning
Structural Review Clerk
(Revised02/24/2014)
r
Miami shores Village
Building Department
10050 N.E.2nd Avenue
Miami Shores, Florida 33138
Tel: (305) 795.2204
Fax: (305) 756.8972
CONTRACTORS' REGISTRATION
IF CONTRACTOR IS A FLORIDA STATE CERTIFIED CONTRACTOR:
A. X COPY OF QUALIFIER'S STATE LICENCES
B. X COPY OF LOCAL BUSINESS TAX RECEIPT
C. X COPY OF LIABILITY INSURANCE*
D. X COPY OF WORKERS COMPENSATION INSURANCE*
(Workers Compensation EXEMPTION must have NOTICE TO OWNER form and Contractor Affidavit)
IF CONTRACTOR HAS A MIAMI DADE COUNTY CERTIFICATE OF COMPETENCY:
A. COPY OF CERTIFICATE OF COMPETENCY OF QUALIFIER
B. COPY OF LOCAL BUSINESS TAX RECEIPT
C. COPY OF STATE REGISTERED CONTRACTOR LICENSE OR MIAMI DADE COUNTY MUNICIPAL
CONTRACTOR'S TAX RECEIPT.
D. COPY OF LIABILITY INSURACE*
E. COPY OF WORKERS COMPENSATION INSURANCE*
(Workers Compensation EXEMPTION must have NOTICE TO OWNER form and Contractor Affidavit)
*YOUR INSURANCE COMPANY MUST ISSUE A CERTIFICATE AS FOLLOW:
Certificate Holder:
MIAMI SHORES VILLAGE BLDG DEPT
10050 NE 2ND AVE
MIAMI SHORES, FL 33138
Certificate must specify the description of operations or contractor license number.
...........................................................................................
BUSINESS NAME:
PRECISION ROOFING CORP
BUSINESS ADDRESS: 2646 W 77 PL CITY HIALEAH STATE FLA ZIP 33016
BUSINESS PHONE: 31 05 ) 822-9969 FAX NUMBER( 305) 822-492
CELL PHONE (305 ) 345-5725 QUALIFIER'S NAME: JOANNA TALLET
QUALIFIER'S LIC NUMBER: CCC 1329365
Florida Building Code 6th Edition (2017) • • • • •
High -Velocity Hurricane Zone Uniform Permit Application Fo1M
000:0* ..
Section A (General Information) """ •
Master Permit Number Process Number "" • • •
Contractor's Name PRECISION ROOFING CORP • • **-
Job Address 134 NW 94 ST MIAMI SHORES, FL 33150 _• •
ROOF CATEGORY • •
❑ Low Slope ❑ Mechanically Fastened Tile ® Mortar/Adhesive Set Tile
❑ Asphalt Shingles ❑ Metal Panels/Shingles ❑ Wood Shingles/Shakes
Is there an existing Roof Top Solar System? (' Yes a, No Will it be reinstalled? (', Yes (R__ Na. TX ET-)
E
Are there gas vents on the roof? (`) Yes Q No Type? ❑Natural ❑ LPGX
ROOF TYPE
❑ New Roof ❑ Repair ❑ Maintenance ® Reroofing
ROOF SYSTEM ROOF INFORMATION
Low Slope Roof Area (ft) N/A Steep Slope Roof Area (ft) 2,400
Section B (Roof Plan)
J U NN L016) Lt,
❑ Recovering ..
Total (ft) 2,400
Sketch the Roof Plan: Illustrate all levels and sections, roof drain, scuppers, overflow scuppers and overflow drains.
Include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and locations of parapets.
i
ti
W .r.
ij
r
~ <
{
>
i j
Ct7 T S
m
cn
Q i
.ram.►
r
i i
n .t Y.
123 01-48 4/19 PAGE 2
t
Florida Building
. . .... .. ....
Code 6th Edition (2017) '
High -Velocity Hurricane Zone Uniform Permit Application FoAp.' .•.. •'
.... .... . .
Section C (Low Slope Application)
Top Ply Fastener/Bonding Mateft* '
... .... .....
Fill in specific roof assembly components and identify
-""
"""
manufacturer
" Surfacing: 00 60 000000
(If a component is not used, identify as "NA")
000m.. '.
Fastener Spacing for Anchor/Base Slhee�t Attac�ment .
..••.•
System Manufacturer:
y
Field: " oc @Lap, #Rows : 00 4_ • " oc � • • • • •
• . •
Perimeter: " oc @ Lap, # Rows @ ' oc
Product Approval No.:
_
Corner: oc @ Lap, # Rows @ oc
" "
Design Wind Pressures, From RAS 128 or Calculations:
Number of Fasteners Per Insulation Board:
P1: P2: P3:
Field Perimeter Corner
Max. Design Pressure, from the specific product
approval system:
Illustrate Components Noted a Details as Applicable:
Woodblocking, Gutter, Ed ermination, Stripping, Flashing,
Deck:
Continuous Cleat, Cant ip, Base Flashing, Counterflashing,
Type:
Coping, Etc.
Indicate: Mean Ro Height, Parapet Height, Height of Base
Gauge/Thickness:
Flashing, Comp ent Material, Material Thickness, Fastener
Type, Fasten Spacing or Submit Manufacturers Details that
Slope:
Comolv wi AS 111 and Chaoter 16.
Anchor/Base Sheet & No. of Ply(s):
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insulation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation Layer:
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding
aterial:
Base Sheet(s) & No. of Ply:
Base Sheet Fastener/Bonding Material:
Ply Sheet(s) & No. of Ply(s):
Ply Sheet Fastener/Bonding Material:
Top Ply:
III
FT. {
L�arapet
eight
FT.
Mean
Roof
Height
123 01-48 4/19 PAGE 3
t
....
Florida Building Code 6th Edition (2017)
• • • • •
PIGS**
High -Velocity Hurricane Zone Uniform Permit Application Form"
.";'.
1 '.
Section D (Steep Sloped Roof System) ....
....
:1"':
Roof System Manufacturer: BORAL ROOFING LLC ..•...
.•..
l•
oleo*
Notice of Acceptance Number: 18-0829.02 so
0 • 0
01.::.
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations):
• •
• 1 •• : •
P1: -39.1 P1: -68.1 P1: -100.7
......
•
:1...:
� •••
• ...
1
Deck Type: CDX PLYWOOD 5/8 = 19/32"
1
_�
\ Type Underlayment: (1) ASTM D226 FELT TYPE 11 PAPER #30
1
Roof Slope:
\�
3.5 12
Insulation:
f -
N/A
1
\
`
1
Ridge Ventilation?
n/a
rNMean Roof Height
1 1<1
Fire Barrier: N/A
Fastener Type & Spacing: 1=1/4 R/S NAILS& 1578TIN CAPS 1
Ups @.6" Field 2 Rows 12" O.01
1
Adhesive Type: [ ICP AH-160 TILE ADHESIVE ] 1
_ 1
Type Cap Sheet: CORAL TILE SEAL SELF ADHERED 1
� 1
\ Roof Covering: oral Plantation Cement Tiles ,
Type &Size Drip 30 G-,aly 26Ga. Drip Edge l 1
\� Edge: W/1-1/4 R/S Nails a 4" O:G 1
1
123 01-48 4/19 PAGE4
Florida Building Code 6th Edition (2017)
• • • •
••••••
High -Velocity Hurricane Zone Uniform Permit Application Forth
••••••
.. .
•.•• •
Section E (Tile Calculations) 000000
•
For Moment based tile systems, choose either Method 1 or 2. Compare the values for Mr with the vajLWffgm M,.
are greater than or equal to the Mr values, for each area of the roof, then the tile attachment method is•arooeptable.
Ut1T21t11•, value; •
• • • • • • • • •
• •
••••••
•••• •••••
Method 1 "Moment Based Tile Calculations Per RAS 127" be 00
(P1:-39.1 x k.289 = 11.30) _ Mg: 7.67 = Mr, 3.63 Product Approval M, 31.3 • • • • • •.
(P2:-68.1 xk .289 = 19.68) - Mg: 7.67 = Mrz 12.01 Product Approval M, 31.5 • 0...0 000000
(P3-100.7xk.289 = 29.10) - Mg: 7.67 = Mr3 21.43 Product Approval M, 31.1 .'. ' :..••:
Method 2 "Simplified Tile Calculations Per Table Below"
Required Moment of Resistance (Mr) From Table Below Product Approval M,
Mr required Moment Resistance`
Mean Roof Height
Roof Slope
15'
20'
25'
30'
40'
2:12
34.4
36.5
38.2
39.7
42.2
3:12
32.2
34.4
36.0
37.4
39.8
4:12
30.4
32.2
33.8
35.1
37.3
5:12
28.4
30.1
31.6
32.8
34.9
6:12
26.4
28.0
29.4
30.5
32.4
7:12
24.4
25.9
27.1
28.2
30.0
'Must be used in conjunction with a list of moment based tile systems endorsed by the Broward County Board of Rules and
Appeals.
For Uplift based tile systems use Method 3. Compared the values for F with the values for Fr. If the F' values are greater than or
equal to the Fr values, for each area of the roof, then the tile attachment method is acceptable.
Method 3 "Uplift Based Tile Calculations Per RAS 127"
(P1: x L = x w: _ ) - W: x cos 0 = Fr, Product Approval F'
(P2: x L = x w: _ ) - W: x cos 0 = Frz Product Approval F'
(P3: x L = x w: _ ) - W: x cos O = Fri Product Approval F'
Where to Obtain Information
Description
Symbol
Where to find
Design Pressure
P1 or P2 or P3
RAS 127 Table 1 or by an engineering analysis pre-
pared by PE based on ASCE 7
Mean Roof Height
H
Job Site
Roof Slope
0
Job Site
Aerodynamic Multiplier
x
Product Approval
Restoring Moment due to Gravity
M9
Product Approval
Attachment Resistance
M,
Product Approval
Required Moment Resistance
M9
Calculated
Minimum Attachment Resistance
F'
Product Approval
Required Uplift Resistance
Fr
Calculated
Average Tile Weight
W
Product Approval
Tile Dimensions
L = length W = width
Product Approval
All calculations must be submitted to the
building official at the time of permit application.
123 01-48 4/19 PAGE 5
•
••••••
••••
SECTION 1524
• • • •
• • •
HIGH VELOCITY HURRICANE ZONES — REQUIRED OWNERS NOTIFICITION•FOR ROOFING
CONSIDERATIONS
• •. • • •
1524.1 Scope. As it pertains to the section, it is the responsibility of roofing contractor to provide the owner with
the required roofing permit, and to explain to the owner the content of the section. The provisions of Section R440;
govern the minimum requirements and standards of the industry for roofing system installations. Additionally, the
following items should be addressed as part of the agreement between the owner ant the contractor. The owner's
initial in the designated space indicates that the item has been explained.
2. _Renailing wood decks: When replacing roofing, the existing wood roof deck may have to
be renailed in accordance with the current provisions of Section R4403. (The roof deck is usually
concealed prior to removing the existing roof system).
4. 14, A" Exposed Ceiling: Exposed, open beam ceilings are where the underside of the roof decking
can be viewed from below. The owner may wish to maintain the architectural appearance; therefore,
roofing nail penetration of the underside of the decking may not be acceptable. This provides the option of
maintaining the appearance.
6. MOverflow scuppers (wall outlets): It is required that rainwater flows off so that the roof is
not overloaded from a buildup of water. Perimetededge wall or other roof extension may block this
discharge if ov rflow scuppers (wall outlets) are not provided. It may be necessary to install overflow
scu rs ' or th the requirements of Sections R4402, R4403 and R4413.
S/7 1�1
Owner/Agent Signature Date Contrac4Sigre t D to
k3L'1 �Jwqyo
Pro 7rty Address�QV Skim'
Revised on 7/9/2009 LD;07/01/2015;
Permit Number
Miami Shores Village
Building Department
10050 N. E.2nd Avenue
Miami Shores, Florida 33138
Tel: (305) 795.2204
Fax: (305) 756.8972
OWNERS'S AFFIDAVIT OF EXEMPTION
ROOF TO WALL CONNECTION HURRICANE MITIGATION RETROFIT FOR EXISTING SITE -
BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES
PERSUANT TO SECTION 553.844 F.S.
To: Miami Shores Village Building Department Date:
10050 NE 2nd Ave • • • • •
. . sees sees..
Miami Shores, FI 33138 •
.. sees
Re: Owner's Name: MARI ARISTIZABAL • •';' • *.so
• • • • • •
sees..
Property Address: 134 NW 94 ST MIAMI, FL 33150 e
sees sees :*see:
.. sees.
Roofing Permit Number: ••;••;9 0 0••�••�
Dear Building Official: • • • • • • • -
.. s
. . . . .sees.
MARI ARISTIZABAL • • • • • •
certify that I am not required to retrofit the rogf togll connections of rrty.....
building because: so 0 •.;.. •
V/The just valuation for the structure for purpose of ad valorem taxation is less than $300,000.00, Please attach proof of ad
valorem taxation.
o The building was constructed in compliance with the provisions of the Florida Building Code (FBC) or with the provisions
of 1994 edition of e South Florida Building Code (1994 SFBC)
Signature Print Name
State of Florida
County of Dade
The undersigned, being the first duly sworn, deposes and says that he/she is Pe owner for the above property mentioned.
Sworn to and subscribed before me this 1-7 d y of ?A910
Notary Public, Sate of Florida at Large
CARLOS A URBINA
Notary Public - State of Florida
Commission ; GG 329183
My Comm. Expires Jul 31, 2023
Banded through National Notary Assn.
When the just valuation of the structure for purpose of ad valorem taxation is equal to or more than $300,000.00, and the building was not constructed with FBC nor a 1994
SFBC. Then you must provide a building application from a General Contractor for the Roof to Wall connection Hurricane Mitigation.
Revised on 5/21/2009
Miami Shores Village
Building Department
10050 N.E.2nd Avenue
Miami Shores, Florida 33138
Tel: (305) 795,2204
Fax: (305) 756.8972
AFFIDAVIT OF COMPLIANCE WITH ROOF TO WALL CONNECTION HURRICANE MITIGATION
RETROFIT FOR EXISTING SITE -BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES PURSUANT
TO SECTION 553.844 F.S.
To: Miami Shores Village Building Department
10050 NE 2nd Ave
Miami Shores, FI 33138
Re: Owner's Name: k by (
Date: .5" 17 " 1 t*1
•ee
•• • ....
Property Address: 13q AJW qq ST 11IA-lA I S ,��. � �O •. •
Roofing Permit Number: •.... • • • • • • •
...... ....
.....
.....
Dear Building Official: r �� .. .
I L Gl certify that I have improved the roof to wallconeeetions of the refereNeed•:
•• • . •• •
property as required by the Manual of Hurricane Mitigation Retrofits for Existing Site -Built Single Family %tfdential
Structures as adopted by the Florida Building Commission by Rule 9B-3.047 F.A.C.
Signature
State of Florida
County of Dade
The undersigned, being the
Sworn to and subscribed bE
Notary Public, Sate of Florio
(SEAL)
Revised on 5/21/2009
Print Name
)erty mentioned.
FINAL COMPLIANCE
MIAMI•DADE
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
HOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.aov/economy
Boral Roofing LLC.
7575 Irvine Center Drive, Suite 100
Irvine, CA 92618
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Contr.01 Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to htw."l •, •• •.
product or material tested for quality assurance purposes. If this product or material fails to pe*forwn in thaaawpted .'
manner, the manufacturer will incur the expense of such testing and the AHJ may immediatelyVwke, Amify *'or • • • • •
suspend the use of such product or material within their jurisdiction. RER reserves the right I(T Woke this atceptanc:, •, •;
if it is determined by Miami -Dade County Product Control Section that this product or matorial'fails to rucefthe '
requirements of the applicable building code. • •
......... .....
This product is approved as described herein, and has been designed to comply with the Florj�i'9. ;ilding "hle: , • • • • •
including the High Velocity Hurricane Zone of the Florida Building Code. 000000
. . . • •••.••
DESCRIPTION: BORAL TileSeal • • • •
•
. . ...0..
.. • •
. .
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state anlronowing
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This new NOA consists of pages I through 4.
The submitted documentation was reviewed by Alex Tiger•a.
NOA No.: 18-0502.03
QMIAMI.DAD; COUNTY Expiration Date: 08/02/23
Approval Date: 08/02/18
Page 1 of 4
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Underlayment
Material: SBS
PRODUCTS DESCRIPTION:
Product Dimensions
BORAL TileSeal 36" x 36' rolls
36" x 72' rolls
Boral Citadel Plus 36" x 72' rolls
MANUFACTURIGN LOCATION:
l . Brentwood, NH.
2. Houston, TX.
EVIDENCE SUBMITTED:
Test Agency
PRI Construction Materials
Technologies, LLC.
Trinity ERD
Test Product
Specification Description
TAS 103 SBS self -adhering asphalt sheet material with a
ASTM D 1970 white glass re -enforced polyester surfacing fabric;
for use as an underlayment in sloped roof
assemblies.
ASTM D1970
Test Identifier
OCF-356-02-04
OCF-3 56-02-02
OCF-3 56-02-01
OCF-424-02-04
OCF-424-02-01
OCF-424-02-03
BRLRF-SC 16810.1 1.17
SBS self -adhering asphalt sheet material with a
poly film -facer; for use as a mid-plyup4erlayment
in sloped roof assemblies.
Y •
.Y.. ......
......
.• . ......
....•.
•...
.•.. . •
• •
• •
. ••.
•••• •••••
.•••.•
•••• ••••••
•• ••
•• • •010•0
••••..
.
• •
Test Name/Report
• ••••••
• • • •• Date
•
• •
ASTM D16230•••
407/25/18�••••:
•0•1061/24/18
TAS 103
ASTM D1970
07/26/18
ASTM D1623
07/25/18
ASTM D1970
07/25/18
TAS 103
07/25/18
ASTM D 1876 11/28/17
NOA No.: 18-0502.03
Expiration Date: 08/02/23
Approval Date: 08/02/18
Page 2 of 4
APPROVED ASSEMBLIES:
Deck Type 1: Wood, non -insulated
Deck Description: 15/32" or greater plywood or wood plank
System E(1): Anchor sheet mechanically fastened deck, membrane adhered.
Base Sheet:
One or more plies of ASTM D226 Type II or ASTM D2626 with a minimum 4" head lap and a
6" end lap mechanically fastened to deck with approved nails and tin caps 6" o.c. at the laps
and two staggered rows 12" o.c. the field of the roll.
Ply Sheet
Apply one layer of Boral Citadel Plus over Base sheet as per current approval.
(Optional):
Membrane:
One or more plies of BORAL TileSeal Underlayment with a minimum 3; head tba .Oa ld
.....
minimum 6" end lap. Place the first course of membrane parallel to the*eave, rollirigihe .'
membrane to obtain maximum contact. Remove the release membrane:2"the ryWra;e is ....:.
applied. Vertical strapping of the roof with BORAL TileSeal UnddrlVrtrtnt is acceptable. All...
end laps and laps without black selvage area shall be sealed under lap rising an SAS*Udified •
... .... .....
mastic. ...... .... .....
.. .. .. . ......
Note: When used in Tile roof systems BORAL TileSeal Underlaynaentsball be back nailed to .•
deck with approved annular ring shank nails and tin caps at a maxi;nA It" o.c. at the side ......
......
. . . .
laps. No nails or tin caps shall be exposed.
.. . . ..
Surfacing:
. . .
Approved for Adhered Roof Tile using TILE BOND or AH-160, Mechanically Fasfelhed Roof
Tile, Metal Roofing, Wood Shake & Shingles, and Asphaltic Shingle assemblies.
NOA No.: 18-0502.03
Expiration Date: 08/02/23
Approval Date: 08/02/18
Page 3 of 4
LIMITATIONS:
1. Fire classification is not part of this acceptance.
2. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code. BORAL TileSeal underlayment shall be installed in strict compliance with applicable
Building Code.
3. BORAL TileSeal underlayment shall be applied to a smooth, clean and dry surface with deck free of irregularities.
4. BORAL TileSeal underlayment shall not be applied over an existing roof membrane as a recover, but may be
applied over a roofing Base/Anchor sheet underlayment.
5. BORAL TileSeal underlayment shall not be left exposed as a temporary roof for longer than 180 days of
application.
6. The standard maximum roof pitch for BORAL TileSeal underlayment shall be 6:12 when tiles are loaded directly
to the BORAL TileSeal underlayment; loading boards or battens are required on roof pitches "greater R * 6:12". •
7. Refer to Prepared Roofing system Product Control Notice of Acceptance for listed appr;waro;this prp�;:t with
specific prepared roofing products. • • • • • • •. ......
8. Tiles shall be stored on battens on roof pitches greater than 6:12". """ •
9. BORAL TileSeal underlayment may be used with any approved roof covering Notice of A�Ptance*Utjgg � � •
BORAL TileSeal underlayment as a component part of an assembly in the Notice of Acceptance. If FIQAAL .., • •
TileSeal underlayment is not listed, a request may be made to the Authority Having Jurrsdiot4n (A1-1.>,)•or tie ......
Miami -Dade County Product Control Department for approval provided that appropriatrkIlVentation•is •�
provided to detail compatibility of the products, wind uplift resistance, and fire testing ►'esults.' • • • • • •
10. All nails in the deck shall be carefully checked for protruding heads. Re -fasten any I00%Itcting pjnel�,, SweeC••••:
the deck thoroughly to remove any dust and debris prior to application. :.. •
11. When applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane
from the center outward in both directions. For ridge applications, center the membrane and roll from the center
outward in both directions.
12. Roll or broom the entire membrane surface so as to have 100% contact with the surface, giving special attention to
overlap areas.
13. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance and applicable Building Code.
14. All protrusions or drains shall be initially taped with a 6" piece of underlayment. This target piece shall be pressed
in place and formed around the protrusion to ensure a tight fit. A second layer of BORAL TileSeal underlayment
shall be applied over the underlayment, and sealed using an SBS modified mastic.
15. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
16. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo, city
and state of manufacturing facility, and the following statement: "Miami -Dade County Product Control Approved"
or the Miami -Dade County Product Control Seal as shown below
END OF THIS ACCEPTANCE
NOA No.: 18-0502.03
Expiration Date: 08/02/23
Approval Date: 08/02/18
Page 4 of 4
MIAMI-DADE COUNTY
MIAMI-DiADE PRODUCT CONTROL SECTION
7111-1. 11805 SW 26 Street, Room 208
DEPARTMENT OF RECULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.sov/economv
Boral Roofing, LLC
7575 Irvine Center Drive, Suite 100
Irvine, CA 92618
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade Courlty Pr
oduct Gortrol• Section
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) res%x4C t:e right iY have this • •
product or material tested for quality assurance purposes. If this product or material fails.to.porform hUlfe :cceptrJ..;,
manner, the manufacturer will incur the expense of such testing and the AHJ may immee ialaly revoke, modify, or...
suspend the use of such product or material within their jurisdiction. RER reserves the riglIt'tboityoke tD>' aNeptanee, •
if it is determined by Miami -Dade County Product Control Section that this product or 3rtatLrial failS'tb'meet tttp;••.
requirements of the applicable building code.
...... 0 .... 0 .....
.. .. .. . ......
This product is approved as described herein, and has been designed to comply with :he lorida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code. • • •• %
DESCRIPTION: Plantation Roof Tile '.:..'
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA #15-0721.04 and consists of pages 1 through 7.
The submitted documentation was reviewed by Freddy Semino 0
NOA No.: 18-0829.02
Expiration Date: 12/08/20
Approval Date: 10/11/18
Page 1 of 8
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub -Category: Roofing Tiles
Material: Concrete
1. SCOPE
This approves a roofing system using Boral Plantation Concrete Roof Tile, as manufactured by Boral Roofing, LLC
in Okeechobee, FL as described in Section 2 of this Notice of Acceptance, designed to comply with the Florida
Building Code for High Velocity Hurricane Zone. For use in locations where the pressure requirements, as determined
by applicable Building Code, do not exceed the design pressure values obtain by calculations in compliance with RAS
127 using the values listed in section 4 herein. The attachment calculations shall be prepared as a moment based
system.
2. PRODUCT DESCRIPTION
Manufactured by Dimensions
Applicant
Plantation Tile Length: 16'/z"
Width: 13"
Trim Pieces ' L = varies
W = varies
Varying thickness
2.1. MANUFACTURING LOCATION
1. Okeechobee, FL
•
• • •••• ••••••
...... .. . ......
Test
..Product :"":
Specifications
� •. •
•D*ceriptio%...'
TAS 112
.�..�
Flat concrete r(Wdle fordiNA•deck c1i'
battened
nail Qn,* mortar or adhesive set •.
applications
0 ••••:•
.••••.
TAS 112
Accessory tritons c41cretewooilDieces for*
use at hips, rakes, ridges ardm3ley
terminations. Manufactured for each tile
profile.
2.2 PRODUCTS MANUFACTURED BY OTHERS
Product Name
ICP Adhesives Polyset® AH-160
TILE BOND TM Roof Tile Adhesive
DAP Foam Touch N Seal
StormBond® 2 Roof Tile Adhesive
Quikrete" Roof Tile Mortar, FL-15
Product Description
Two component polyurethane
foam adhesive.
Single component polyurethane
foam roof tile adhesive.
Two component polyurethane
foam adhesive.
Premixed, pre -bagged gray roof tile
mortar.
Manufacturer
(With Current NOA)
ICP Adhesives and Sealants, Inc.
The Dow Chemical Company
Dap Foam, Inc.
The Quikrete Companies, Inc.
NOA No.: 18-0829.02
Expiration Date: 12/08/20
Approval Date: 10/11/18
Page 2 of 8
2.3 SUBMITTED EVIDENCE:
Test Agency
American Test Lab of South
Florida
Redland Technologies
The Center for Applied
Engineering, Inc.
Redland Technologies
Redland Technologies
Redland Technologies
Redland Technologies
The Center for Applied
Engineering, Inc.
Walker Engineering, Inc.
Walker Engineering, Inc.
Walker Engineering, Inc.
Walker Engineering, Inc.
Farabaugh Engineering and
Testing Inc.
Farabaugh Engineering and
Testing Inc.
Farabaugh Engineering and
Testing Inc.
PRI Construction Material
Technologies
3. LIMITATIONS
Test Identifier
RT0624.05-14
7161-03
Appendix III
94-060B
94-084
7161-03
Appendix 11
Letter Dated Aug. 1, 1994
P0631-01
P0402
Project No. 307025
Test #MDC-76
Calculations
Calculations
Calculations
Calculations
T295-11
T306-11
T279-1 1
DA PF-004-02-08
DA PF-004-02-09
DA PF-004-02-10
Test Name/Report
TAS 112
Static Uplift Testing
PA 102 & PA 102(A)
Static Uplift Testing
PA 101 (Adhesive Set)
(Mortar Set)
Wind Tunnel Testing
PA 108 (Nail -On)
Wind Tunnel Testing
PA 108 (Nail -Oro •••
Wind Tunnel Testirig•
PA 108 (Mortar Seo.:.•
. ....
Withdrawal Resistance Tq„ 44 g of
screw vs. smooth shan%ia4i19'
Wind Driven Rain....
PA 100 ••••••
Aerodynamic MultiPfi%*:
25-7183 o •••
•• •
25-7094
25-7496
25-7584
25-7804b-8
25-7804-4 & 5
25-7848-6
Two Patty Adhesive Set System
TAS-108
TAS-108
TAS-108
TAS 101
Static Uplift Resistance
Adhesive Set
Date
07/03/14
Dec. 1991
March, 1994
May 1994
Dec. 1991
0.Amg61994
•••• ••••••
.•141%1994 •,
. apt. 1993: • •..
0000
0". 1994..;.. •
March 1999 •,
March 194....:
'F.epr:ttry 146 •
April 1996
December 1996
April 1999
10/05/11
10/04/ 1 1
09/23/11
07/26/18
07/26/18
07/26/18
3.1 Fire classification is not part of this acceptance.
3.2 For mortar or adhesive set tile applications, a static field uplift test shall be performed in accordance with
TAS 106.
3.3 Applicant shall retain the services of a Miami -Dade County Certified Laboratory to perform quarterly test
NOA No.: 18-0829.02
6M►•DADE COUNTY Expiration Date: 12/08/20
Approval Date: 10/11/18
Page 3 of 8
in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Miami -Dade Product
Control office for review.
3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed
section 4.1 herein.
3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated
otherwise by the underlayment material manufacturers published literature.
3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with
applicable building code.
3.7 All products listed herein shall have a quality assurance audit in accordance with the Florida Building
Code and Rule 61 G20-3 of the Florida Administrative Code.
4. INSTALLATION • • • • • • • • • •
4.1 Plantation Roof Tile and its components shall be installed in strict compliant. wej. Roofir";A*licat"j::•
Standard RAS 1 18, RAS 119 and RAS 120. •.•:..
4.2 Data For Attachment Calculations • • • • 660860
•
*000
Table 1: Average Weight (W) and Dimensions (I x w )••:••: •••:•. ••• •
.. •• gig • ... . .
Tile Profile
Weight-W (Ibf)
Length-1 (ft)
••••••Width-w (ft) •
Plantation Tile
11.6
1.375
j.06••• •
6.0
. • • • • • •
Table 2: Aerodynamic Multipliers -X (ft3) ••••
Tile
Profile
X (ft3)
Batten Application
ft )
Direc k App ication
Plantation Tile
0.267
0.289
1�I
Table 3: Restoring
Moments due to Gravity - M (ft.-Ibf)
Tile
Greater than
Profile
2":12"
3":12"
4":12"
5":12"
6":12"
7":12"
Battens
Direct
Battens
Direct
Battens
Direc
Battens
Direct
Battens
Direct
Battens
Direct
Deck
Deck
Deck
Deck
Deck
Deck
Plantation
7.22
7.91
6.85
7.79
6.75
7.67
6.61
7.52
6.44
7.32
6.26
7.04
Tile
NOA No.: 18-0829.02
MIAMI•DADECOUNTY Expiration Date: 829.02
/08/20
Approval Date: 10/11/18
Page 4of8
Table 4: Attachment Resistance Expressed as a Moment - Mr (ft-Ibf)
For Nail -On Systems
Tile
Fastener Type
Direct Deck
Direct Deck
Battens
Profile
(Min 15/32"
(Min. 19/32"
plywood)
plywood)
Plantation Tile
2-10d Ring Shank
30.9
38.1
17.2
Nails
1-10d Smooth or
7.3
9.8
4.9
Screw Shank Nail
2-10d Smooth or
14.0
18.8
7.4
Screw Shank Nails
1 #8 Screw
30.8
30.8
'.18.2 ...
2 #8 Screw
51.7
51.7
•24A
1-10d Smooth or
24.3
24.3 •••;••
•24.2 •••
Screw Shank Nail
Field Clip)."'•.
.��". '
1-10d Smooth or
19.0
19.0 00•00•
1 �•�
Screw Shank Nail
.. ..
•
.. . ...
Eave Clip)
......
2-10d Smooth or
35.5
35.5
• 34.-8 • • •
Screw Shank Nails
Field Clip)
2-10d Smooth or
31.9
31.9
"1212
Screw Shank Nails
Eave Clip)
2-10d Ring Shank
50.3
65.5
48.3
Nails'
l Installation with a 4" the
headiap and fasteners are located a minimum of 2'/z'from the head of tile.
Table 5: Attachment Resistance Expressed as a Moment Mf (ft-Ibf)
For Two Patty Adhesive Set Systems
Tile Profile
Tile Application
Minimum Attachment
Resistance
Plantation Tile
Adhesive
2 See manufactures component approval for installation requirements.
3 The Dow Chemical Co. TILE BONDTm Roof Tile Adhesive weight per patty 13.9 grams. 31.3
4 ICP Adhesive and Sealants, Inc. ICP Adhesve Polyset® AH-160 Two -Component weight per patty 8 grams. 31.3
DAP Foam Touch N Seal StormBond® 2 Roof Tile Adhesive weight per paddy 8 grams. 45
NOA No.: 18-0829.02
Expiration Date: 12/08/20
Approval Date: 10/11/18
Page 5 of 8
Table 6: Attachment Resistance Expressed as a Moment - Mf (ft-Ibf)
For Single Patty Adhesive Set S stems
Tile Profile
Tile Application
Minimum Attachment Resistance
Plantation Tile
Adhesives
6
See manufactures component approval for installation requirements.
7
ICP Adhesive and Sealants, Inc. ICP Adhesve Polysetg AH-160 Two -Component weight per patty 45 grams.
118.9
8
ICP Adhesive and Sealants, Inc. ICP Adhesve Pol set® AH-160 Two -Component weight per patty 24 grams
40.4
9
DAP Foam Touch N Seal StormBondo 2 Roof Tile Adhesive weight per paddy 45 grams.
73
10
DAP Foam Touch N Seal StormBondo 2 Roof Tile Adhesive weight per paddy 24 grams
48
Table 7: Attachment Resistance Expressed as a Moment - Mf(ft-Ibf) ••••
for Mortar Set Systems 0 000000 ...
••••Atachrnegt•
Tile Profile
Tile Application
••••f2esistate• •••
Plantation Tile
Mortar Sets
000000
•'••• 39.0 • :..
Seespecific mortar manufacturer's Notice of Acceptance!*.... •
...... .... .....
5. LABELING •
.. .. .. . ......
All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo:as 9eI below or.followin�•��•
statement: "Miami -Dade County Product Control Approved". • • • • •
W,
� ENTEGRA
BORAL PLANTATION ROOF TILE LABEL (LOCATED ON UNDERSIDE OF TILE)
6. BUILDING PERMIT REQUIREMENTS:
6.1 Application for building permit shall be accompanied by copies of the following:
6.1.1 This Notice of Acceptance.
6.1.2 Any other documents required by Building Official or Applicable building code in order to properly
evaluate the installation of this system.
NOA No.: 18-0829.02
CMIAMI-D�ADECOUNTY�' Expiration Date: 12/08/20
Approval Date: 10/11/18
Page 6 of 8
. .
....
......
......
.. .
......
•..•
••.•
Y•••
••.•
.....
0900
NOA No.: 18-0829.02
Expiration Date: 12/08/20
Approval Date: 10/11/18
Page 7 of 8
PROFILE DRAWING
BORAL PLANTATION FLAT CONCRETE TILE
END OF THIS ACCEPTANCE
NOA No.: 18-0829.02
Expiration Date: 12/08/20
Approval Date: 10/11/18
Page 8 of 8
MTAM - MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamldade.sov/economy
ICP Adhesives and Sealants, Inc.
12505 NW 44' Street
Coral Springs, FL. 33065
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Contrgl*Se( ion to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdi4tiota TAHJ). "" """
This NOA shall not be valid after the expiration date stated below. The Miami -Dade Countojor"duct Nmtro; Section••:•
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve thtletgM to have this prodq("..:
or material tested for quality assurance purposes. If this product or material fails to performA*thisaccep6e'd'iT%mer, ?he '
.... .... *fee&
manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use. .
of such product or material within their jurisdiction. RER reserves the right to i
revoi F :t J; accep}ot-rice••if ito s
0 ......
determined by Miami -Dade County Product Control Section that this product or material faj,ls tp.rpeet the requirements .•
of the applicable building code. ....:.
,.....
This product is approved as described herein, and has been designed to comply with :he .F'lorida'$uilding Cc:i,-o..:
including the High Velocity Hurricane Zone of the Florida Building Code. o e ' : .". ' '
...
DESCRIPTION: ICP Adhesives Polyset° AH-160
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA 16-0315.01 and consists of pages 1 through 11.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 1 of 11
ROOFING COMPONENT APPROVAL:
Category: Roofing
Sub Category: Roof tile adhesive
Materials: Polyurethane
SCOPE:
This approves ICP Adhesives Polyset® AH-160 as manufactured by ICP Adhesives and Sealants, Inc. as described
in this Notice of Acceptance. For the locations where the design pressure requirements, as determined by applicable
building code, do not exceed the design pressure values obtained by calculations in compliance with Roofing
Application Standard RAS 127. For use with approved flat, low, and high profile roof the systems using ICP
Adhesives Polyset° AH-160.
PRODUCTS MANUFACTURED BY APPLICANT:
Product Dimensions Test
Specifications
ICP Adhesives N/A TAS 101
Polyset°AH-160
ICP Adhesives Foam N/A
Dispenser RTF1000
Product Description
Two component polyurethane foam adhesive
Dispensing Equipment
ICP Adhesives ProPacV' N/A Dispensing Equipment
."".
. .
....
......
30 & 100 •••� 9
••••
••
.
.
......
.. .
......
PRODUCTS MANUFACTURED BY OTHERS: ....
..:a*•
• • •
. .
. ..
Any Miami -Dade County Product Control Accepted Roof Tile Assembly having a current N(;A
.........
list
which
gtjgchment.•:•.•
the of ICP Adhesives Polyset® AH-160 roof tile adhesive.
•..'
resistance values with use ••'..'
......
•
MANUFACTURING LOCATION: . .
. .
......
......
'..'
:•••�:
1. Tomball, TX.
..
PHYSICAL PROPERTIES:
Property Test
Density ASTM D 1622
Compressive Strength ASTM D 1621
Tensile Strength ASTM D 1623
Water Absorption ASTM D 2127
Moisture Vapor Transmission ASTM E 96
Dimensional Stability ASTM D 2126
Closed Cell Content ASTM D 2856
Results
1.6 lbs./ft.'
18 PSI Parallel to rise
12 PSI Perpendicular to rise
28 PSI Parallel to rise
0.08 Lbs./Ft2
3.1 Perm / Inch
+0.07% Volume Change @ -40' F., 2 weeks
+6.0% Volume Change @158'F., 100% Humidity, 2
weeks
86%
Note: The physical properties listed above are presented as typical average values as determined by
accepted ASTM test methods and are subject to normal manufacturing variation.
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 2 of 11
EVIDENCE SUBMITTED:
Test Agency
Center for Applied Engineering
Miles Laboratories
Polymers Division
Ramtech Laboratories, Inc.
Southwest Research Institute
Trinity Engineering
Celotex Corp. Testing Services
Test Identifier
Test Name/Report
Date
494-060
TAS 101
04/08/94
257818-IPA
TAS 101
12/16/96
25-7438-3
SSTD 11-93
10/25/95
25-7438-4
25-7438-7
SSTD 11-93
11/02/95
25-7492
SSTD 11-93
12/12/95
NB-589-631
ASTM D 1623
02/01/94
9637-92
ASTM E 108
04/30/93
01-6743-011
ASTM E 108
1 1/16/94
01-6739-062b[1]
ASTM E 84
01/16/95
7050.02.96-1
TAS 114
03/14/96
P36700.04.12
ASTM D 1623
04/18/12
P39740.02.12
TAS 101
02/21/12
TAS 123
sees
. .
....
•....e
528454-2-1
TAS 101
• • s
N.8
00
528454-9-1
" " "
" '
" " "
528454-10-1
"
520109-1
TAS 101
s • s •
12/I J%9-8
....
.. .
.....
520109-2
s '
......
....
.....
520109-3
000000
' '
.. .
......
520109-6
ss.sss
s
••
•
520109-7
0
. .
. .
......
520191-1
TAS 101
•eeee•
05/02/99
,00e0;
••e
520109-2-1
•• '
'
•e•
LIMITATIONS:
1. Fire classification is not part of this acceptance. Refer to the Prepared Roof Tile Assembly for fire rating.
2. ICP Adhesives Polyset' AH-160 shall solely be used with flat, low, & high tile profiles.
3. Minimum underlayment shall be in compliance with the Roofing Application Standard RAS 120.
4. Roof Tile manufactures acquiring acceptance for the use of ICP Adhesives Polyset® AH-160 roof tile adhesive
with their tile assemblies shall test in accordance with TAS 101.
5. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 3 of 1 I
INSTALLATION:
1. ICP Adhesives Polyset® AH-160 may be used with any roof tile assembly having a current NOA that lists
attachment resistance values with the use of ICP Adhesives Polyset® AH-160.
2. ICP Adhesives Polyset® AH-160 shall be applied in compliance with the Component Application section and the
corresponding Placement Details noted herein. The roof tile assembly's adhesive attachment with the use of ICP
Adhesives Polyset® AH-160 shall provide sufficient attachment resistance to meet or exceed the resistance value
determined in compliance with Miami -Dade County Roofing Application Standards RAS 127. The adhesive
attachment data is noted in the roof tile assembly NOA.
3. ICP Adhesives Polyset® AH-160 and its components shall be installed in accordance with Roofing Application
Standard RAS 120, and ICP Adhesives and Sealants, Inc.'s Operating Instruction and Maintenance Booklet.
4. Installation must be by a Factory Trained 'Qualified Applicator' approved and licensed by ICP Adhesives and
Sealants, Inc. ICP Adhesives and Sealants, Inc. shall supply a list of approved applicators to the authority having
jurisdiction.
5. Calibration of the ICP Adhesives Foam Dispenser RTF 1000 dispensing equipment is required before application
of any adhesive. The mix ratio between the "A" component and the "B" component shall be maintained between
1.0-1.15 (A): 1.0 (B).
6. ICP Adhesives Polyset® AH-160 shall be applied with ICP Adhesives Foam Dispenser RTF 1000 or ICP
Adhesives ProPack' 30 & 100 dispensing equipment only.
7. ICP Adhesives Polyset° AH-160 shall not be exposed permanently to sunlight. ....
8. Tiles must be adhered in freshly applied adhesive. Tile must be set within l to 2 minut$s after ICP Al etives • • • •: •
Polyset® AH-160 has been dispensed. •• •••• •
...... .. . ......
9. ICP Adhesives Polyset® AH-160 placement and minimum patty weight shall be in acco+darooe with the• •
'Placement Details' herein. Each generic tile profile requires the specific placement note4+i%ein. •••••• •0000
...... .... .....
.. .. .. . ......
. . . . ......
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 4 of 11
Table 1: Adhesive Placement For Each Generic Tile Profile
Tile Profile
Placement Detail
Minimum Paddy Contact
Minimum Paddy Gram
Area
Weight
Eave Course - Flat, Low, High
All Eave Course
17-23 sq. inches
45-65
Profiles
Flat, Low, High Profiles
#1
17-23 sq. inches
45-65
Flat Profile
42
10-12 sq. inches
30
Low Profile
42
12-14 sq. inches
30
High Profile
42
17-19 sq. inches
30
Flat, Low, High Profiles
#3
Two Paddys: 8-9 sq. inches at
12 grams per paddy
head of tile 9-1 1 sq. inches at
overlap
Two -Piece Barrel (Cap Tile)
Two Piece
2 Beads (1 each longitudinal
17 grams per bead
edge) 20-25 sq. inches each
bead
Two Piece Barrel (Pan Tile)
Two Piece
65-70 sq. inches
34 grams under pan
. . ....
......
LABELING:
All approved products listed herein shall be labeled and shall bear the imprint or identifiable naarkaa of tRa•' :
•••.:6
manufacturer's name or logo and following statement: "Miami -Dade County Product Control•Approved" or the Miami:
• •.:
Dade County Product Control Seal as shown below. 0000 • • • •
•
.... ....
.....
'
mi...... ....
..:..
l■
•• •• •• •
•.....
•
•..••• .
•
• •
BUILDING PERMIT REQUIREMENTS:
......
. •
As required by the Building Official or applicable building code in order to properly evaluate' r� n:tallatipn (4this
.
;••••;
system.' •:..'
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/t7
Page 5 of I 1
ADHESIVE PLACEMENT DETAIL # I
14anthrsugis plastic ceanau Nddp MmaadhTirk)
jwhm aqulrod * i4
Und.f"tnOO r-A 5
r
L3 4-
Batt.e�soptiona9 ° `�• .� /
Y\. 101n. � �/ �,.• �. J f�'' ^.Fes la
Nall ibra ghv4.u-tccement
(when rew1red1
)1 � ftcw r lBrmr.eh Tavl
nd•r►ay ty �`•..
fattens oplio+aial t ``�`'°`` s�
s� SUP6
�wne
E�r•Zaerse `._ Fascia
FlailsfMouu}hPlisRle nr�,�,�Y�
�,wMnr•grdralh P�Jd'}�IBin..shlrllel
�'ndarlryrwgr b�•
tdlli.d -+ J•�
2 in, wide
aptbonaC � e /�
„ Fascia
. i'YeerrFivle
Eire dasure
1QIm ��.In. > �3iripadga
Flat/Low Profile Tile
I . Starting at the eave course, apply a minimum 2"
(50.8 mm) x 10" (254 mm) x 1" (25.4 mm) foam
paddy onto the underlayment positioned as shown,
under the strengthening rib closest to the overlock
of the tile being set.
2. Continue in same manner. Insure approximately 17
(109.7 cm2) — 23 (148.4 cm2) square inch adhesive
contact with the underside of the tile.
Medium Profile / Double Pan Tile
1. Starting at the eave course, apply a minimum 2"
(50.8 mm) x 10" (254 nim) x 1" (25.4 mm) foam
paddy onto the underlayment positionP4,ac shown
under the pan portion of the tale closesx 4a 411e • • • • • •
overlock of the the beingset •••• •
•••••• •• • ••••••
2. Continue in same mannel-'Ms' -e approximately 1:...•:
(109.7 cm2) — 23 (148.4 cinv square ixiNa4hesive
contact with the underside o the tile. •
...... .... .....
.. .. .. . ......
•• • • •• • •
High Profile / Single Pan Tile '•"
l . Starting at the eave course, apply a minimum 2"
(50.8 inm) x 10" (254 mm) x 1" (25.4 mm) foam
paddy onto the underlayment positioned as shown
under the pan portion of the tile closest to the
overlock of the tile being set.
2. Continue in same manner. Insure approximately 17
(109.7 cm2) — 23 (148.4 cm2) square inch adhesive
contact with the underside of the tile.
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 6 of 11
ADHESIVE PLACEMENT DETAIL # 2
ItAlld+tOughOAX11cOrO*nr PnodyMmm.7hTOO
twhen r•quhad)� " 5 I
Umdadaymma Y i�
V
�,*
EaM•courw
:aWL
•,, a / ,' Fascia
r @rraClosuro
Nail dhraugh plastic cwnnm
;when required)
.4 _-3�od�iy'JBenrathTlla�
nd.rl'ay�ewnl
7Jn.
tKtensorytiona! .ti�
�. .'''.
n.
MIAMI•DADE COUNTY
9. r
Flat/Low Profile Tile
Starting at the eave course, apply a minimum 2" (50.8
min) x 10" (254 min) x 1" (25.4 min) foam paddy
onto the underlayment positioned as shown under the
strengthening rib of the tile closest to the overlock of
the tile being set. Insure approximately 17 (109.7 c1112)
— 23 (148.4 cm2) square inch adhesive contact with the
underside of the tile.
2. At the second course, apply a minimum 2" (50.8mm)
x 7" (177.8 min) x 1" (25.4 min) foam paddy onto the
underlayment positioned as shown under the
strengthening rib closest to the overlock of the tile
being set.
3. Continue in same manner. Insure approximately 10"
(64.5 cm2) - 12(77.4 cm2) square inch adhesive
contact with the underside of the tile.
Medium Profile / Double Pan:Tile�. •�•� •••���
•• • •••• •
•••••• •• • ••••Y•
l . Starting at the eave course,"Qyga minimu►,i 2" (50,8
min) x 10" (254 min) x I" (2.S41nm) fou-apaddy ":
onto the underlayment posiiic",d as shownt0der tha••••
pan portion of the tile closeso r fi a ove►Jeet of the • •' • • •
tile being set. Insure approAtnAP-ly 17 (169.7 em2)
23 (148.4 cm2) square inch: ► &e contactwith the '.
underside of the tile. • ' :•••:• ••••••
2. At the second course, apply a minimum'�;(�Sp'8mm) •
x 7" (177.8 min) x 1" (25.4 mm) foam paddy onto the
underlayment positioned as shown under the pan
portion of the tile closest to the overlock of the tile
being set.
3. Continue in same manner. Insure approximately 12"
(77.4 cm2) - 14 (90.3 cm2) square inch adhesive
contact with the underside of the tile.
(Instructions continued on next page)
NOA No.: 17-0322.03
Expiration Date: 0.5/10/22
Approval Date: 04/27/17
Page 7 of 11
ADHESIVE PLACEMENT DETAIL # 2 (CONTINUED)
N&H t1waugk µbsticcnrnsnt--
t.meArage,trod'I 'v.a r16.r�F�Til.j
r
N-1
7 fi r t
Uattensnptimm.l
f ave IC
Fascia
W.rpha.
1G 21n
E.re dosuwe
brlpedga
High Profile / Single Pan Tile
l . Starting at the eave course, apply a minimum 2" (50.8
mm) x 10" (254 min) x 1" (25.4 mm) foam paddy
onto the underlayment positioned as shown under the
pan portion of the tile closest to the overlock of the
tile being set. Insure approximately 17 (109.7 cmz) —
23 (148.4 cmz) square inch adhesive contact with the
underside of the tile.
2. At the second course, apply a minimum 2" (50.8mm)
x 7" (177.8 mm) x 1" (25.4 mm) foam paddy onto the
underlayment positioned as shown under the pan
portion of the tile closest to the overlock of the tile
being set.
3. Continue in same manner. Insure approximately 17"
(109.7 cmz) - 19 (122.6 cmz) square inch adhesive
contact with the underside of the tile.
. .
....
......
......
.. .
......
....
....
. .
....
....
• .. • .
......
....
.....
.. ..
•• •
......
. .
. .
......
.. •
• ••
•
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 8 of 11
ADHESIVE PLACEMENT DETAIL # 3
Kalf through plastic cement
Paddy (between tiles]
iwhen required)
6attensoptionai °
Paddy {under tire)
" singlepaddy
- on top of tle
r
a xs in,
6�q
Uhl d
under
single paddy
on undedaymenx 4 fn.
tin.
Fare closure
FlatfLow Praflle Tile
Mail through plastic cement
Single paddy under tile.
(when requiredl
Paddy lbetween tiles]
MUM
Paddy runder tlel
aptianal
Al
ontapoftRe
�.
4x4in.
.,
2x4in-
gg a paddy on
sinUnl
+_4-
Yrnrnt �..
to in. F"
2in.
t
Eave Closure
Eare Course
fascia
Madlum ProflleTile
l . On the eave course only, apply a minimum 2" (50.8
mm) x 10" (254 mm) x 1" (25.4 mm) foam paddy
onto the underlayment positioned as shown, under
the strengthening rib for flat tile or under the pan
portion of the tile for low or high profile the closest
to the overlock of the tile being set. Leave
approximately 4" (101.6 mm) up from the eave
edge free of foam to prevent the expanded adhesive
from blocking the weep holes. Insure
approximately 17-23 in' (109.7-148.4 cm') of
adhesive contact with the underside of the tile
2. Apply a 4" (101.6 rnm) x 4" (101.6 mm) x 1" (25.4
rmn) foam paddy onto the underlaymentjust below
the second course line positioned foam paddy
under the strengthening rib for flat tile, or under the
pan portion of the tile, closest to the underlock for
the second course tile to be installed. Insure
approximately 8-9 in (51.6-58.1 cmz) of adhesive
contact with the underside of the tile.
• • •••• ••••••
(Instructions continued on ngxt ,Uaje)
•• • .. . ••••••
•
•••• •••• • •
•••• •••• •••••
•••••• •••• •••••
• • • • • • • • • • • • •
•••••• • •
• • • • •••••••
••••••
• • • •
• • • • • • 000*0
• •
9000
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 9 of 1 l
Al" through plastic
Wien required)
aattem - '.
IN ti—.1 f
'1,�O.n urnne
'4 x 4In.
Sin* 2x43r
paddy on
209
of
die - ,
Eave Course
ADHESIVE PLACEMENT DETAIL # 3 (CONTINUED)
Single paddy under the
Paddy lbetweeo tiksl
Paddy (uncki tile)
High Pro1I142Ttle
Weephak
Eave dosure
Drip edge
3. Also apply a 2" (50.8 mm) x 4" (101.6 mm) x 1/4"
(19 mm) paddy on top of the eave course tile
surface as shown, on top of the strengthening rib
for flat tile or on top of the pan portion of the tile,
closest to the underlock of the first course of tile.
Install second course of tile. Insure approximately
9 (58.1 c1112) - 11 (71 c1112) square inch adhesive
contact with the underside of the tile at the overlap
and 7 (45.2 cm2) - 9 (58.1 cm2) square inch
adhesive contact with the underside of the the at
the head of the tile. Continue in same manner.
• •
••••
••••••
••••••
•• •
••••%
•
••••
••••
• •
••••
••••
•••••
••••••
••••
•••••
•• ••
•• •
••••••
•
• •
• •
••••••
•
•
• •
•• •
• ••
• •
• • •
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 10 of 11
ADHESIVE PLACEMENT DETAIL
TWO PIECE BARREL
1) Place enough adhesive to achieve 65 to 70 sq.In. Steep pitch applications
in contact with the pan tile. (when required)
2) Turn covers upside down. Place adhesive in
to 1 in. from outside edge of cover tile.
Then install the tile. Ensure 20 to
25sq.In.contactarea. ,-Z�
Underlayment
0
Eave closure
(motar shown)
Fascia Board
Remove top portion of the eave course cover tile. Abut to second course of
pan tiles. Ensure eave end of pan and cover tiles are flush at eave line.
Two Piece Barrel - High Profile Tile
Two Piece Barrel (Cap and Pan) Tile
1. Starting at the eave course, apply a minimum 2"
(50.8 mm) x 10" (254 mm) x 1" (25.4 mm) foam
paddy onto the underlayment positioned as
shown under two adjacent pan tiles. Support eave
tiles from rocking until adhesive has a chance to
cure.
2. Continue in same manner bringing two pan
courses up toward the ridge. Insure
approximately 65 (419.4 cm2) — 70 (451.6 cm2)
square inch adhesive contact with the underside
of the pan tile.
Turn covers upside down exposing the underside
of the tile. Apply a minimum 1" (25.4 mm) x 10"
(254 mm) bead of adhesive directly on the inner
edge of each side of the cover tile. Leave
approximately 3/4" (19 mm) to 1" (25.4 mm)
from the outside edge of the tile, irl,Gt&fC, free of
foam to allow for expi'ns i.As "" • • • • • •
• • Y •
Turn cover the over ajl:j fQ:m is al; lJ j and • •
place onto pan tile couly. jnsure a lnipvnum ot••••;
20 (129 cm2) - 25 (161 of ss0) squg"i,r►Gn •...
contact area on each slid@q)fthe cove* We to tha.:..'
Y t .
pan ti le. Continue in !?AiC manner. i'tirn away • • • • • •
any cured exposed fo$tf►'Jd Jesive. Pofiting of •,
longitudinal edges oflhe coLer tilcLare% """
considered optional. • • • • • • • •
of • • .. . •
When additional nailing is required, 2" (50.8
mm) x 4" (101.6 mm) nailers or the tie wire
system using galvanized, stainless steel, or
copper wire and compatible nails may be used.
END OF THIS ACCEPTANCE
NOA No.: 17-0322.03
Expiration Date: 05/10/22
Approval Date: 04/27/17
Page 11 of 11
Miami shores Village
Building Department
10050 N.E.2nd Avenue
Miami Shores, Florida 33138
Tel: (305) 795.2204
Fax: (305) 756.8972
RE: Permit # R f — 06 — 19 — 1 29
DATE:
INSPECTION AFFIDAVIT
1 7— W n In el 11-1 I It �_ licensed as a (n) Contractor / Engineer / Architect,
(Print name and circle License Type) FS 468 Building Inspector
License #: CC( - t 3 2� . ,q3,(!�57-
On or about 7-3— L , 1 did personally inspect the roof deck nailing
(Date 8 time)
work at liq q
(Complete Job Site Address)
oiyS PL 3?iS`b
Based upon that examination I have determined the installation was done according to the Hurricane Mitigation Retrofit
Manual (Based on 553.844 F.S)
Signature
State of Florida
County of Dade:
The undersigned, being the first duly sworn, deposes and says that he/she is the contractor for the above property
mentioned.
Sworn to and subscribed before me this
Notary Public, Sate of Florida at Large
of U�
CARl05 A URBINA
�j Notary Public - State of Florid,
ICJ Commission # GG 329387
My Comm. Expires Jul 31, 20,11
Bonded through Naticnal Nctary Assn!
'General, Building, Residential, or Roofing Contractors or any individual certified under 468 F.S. to make such an inspection. Include photographs of each plane of the roof with
permit # and address # dearly shown marked on the deck for each inspection