The URL can be used to link to this page

RF-17-1336 (2)aFioRioA Project Address Miami Shores Village 10050 N.E. 2nd Avenue NE Miami Shores, FL 33138-0000 Phone: (305)795-2204 Parcel Number Permit No. RF-5-17-1' 336 Permit Type: Roof IM, Work Classification: Tile Permit Status: APPROVED issue Date: 5/1612017 1 Expiration: 11/12/2017 Applicant 94 NE 93 Street 1132060130150 Miami Shores, FL 33138- Block: Lot: CHARLES WALTER MARIA PAU Owner Information Address Phone Cell CHARLES WALTER MARIA PAULA 838 SALZEDO Street - - - CORAL GABLES FL 33134- 838 SALZEDO Street CORAL GABLES FL 33134- Contractor(s) Phone Cell Phone FLORIDA E-Z REMODELING INC (305)796-6753 Type of Work: Re Roof Additional Info: NEW TILE ROOF (ADDITION ONLY) Classification: Residential Scanning: 3 Fees Due Amount CCF $4.20 DBPR Fee $4.13 DCA Fee $4.13 Education Surcharge $1.40 Permit Fee - New Roof $275.00 Scanning Fee $9.00 Technology Fee $5.60 Total: $303.46 Valuation: $ 7,000.00 Total Sq Feet: 1500 Pay Date Pay Type Amt Paid Annt Due Invoice # RF-5-17-64027 05/16/2017 Credit Card $ 50.00 $ 253.46 05/16/2017 Credit Card $ 253.46 $ 0.00 Avauame Inspection Type: Up Lift Report Tin Cap Tile In Progress Renailing Affida Review Roof Cap Sheet In consideration of the issuance to me of this permit, I agree to perform the work covered hereunder in compliance with all ordinances and regulations pertaining thereto and in strict conformity with the plans, drawings, statements or specifications submitted to the proper authorities of Miami Shores Village. In accepting this permit I assume responsibility for all work done by either myself, my agent, servants, or employes. I understand that separate permits are required for ELECTRICAL, PLUMBING, MECHANICAL, WINDOWS, DOORS, ROOFING and SWIMMING POOL work. OWNERS AFFIDAVIT that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoni rmore, I authorize the above -named contractor to do the work stated. May 16, 2017 Au ri Signature: Owner / Applicant / Contractor / Agent uate Buil 'ng Department Copy May 16, 2017 1 Miami Shores Village _ Building Department + MqY szo,� 10050 N.E.2nd Avenue, Miami Shores, Florida 33138 Tel: (305) 795-2204 Fax: (305) 756-8972 INSPECTION LINE PHONE NUMBER: (305) 762-4949 f 9 5!"N FBC 20 BUILDING Master Permit No. P-NC 16-1623 PERMIT APPLICATION Sub Permit No. ?� \I - 133� ❑BUILDING ❑ ELECTRIC [ZROOFING ❑ REVISION ❑ EXTENSION ❑RENEWAL ❑ PLUMBING ❑ MECHANICAL ❑ PUBLIC WORKS ❑ CHANGE OF ❑ CANCELLATION ❑ SHOP CONTRACTOR DRAWINGS JOB ADDRESS: 94 NE 93 Street City: Miami Shores County: Miami Dade Zip: Folio/Parcel#:11-3206-013-0150 Is the Building Historically Designated: Yes NO Occupancy Type: Load: Construction Type: OWNER: Name (Fee Simple Titleholder): Charles Walter Address:94 NE 93 Street City. Miami Shores State: FL Tenant/Lessee Name: Email Flood Zone: BFE: FFE:. Phone#: 347-281-0407 Zip: 33138 Phone#: CONTRACTOR: Company Name: r-Va,:i.6d :E-Z Phone#: 3CFY-A(e• (o-153 Address: 10051 SW u3 S-f+-rtGt ;y - (�o� City: Mkgrrw State: GL Zip: 33((a5 Qualifier Name: "rotor' C,arra�hala Phone#: State Certification or Registration #: CG.4 . 192SO'S5 Certificate of Competency #: _ DESIGNER: Architect/Engineer: Address: Value of Work jor this,Permit: $_ Type of 1Nork:,❑` 'Addition tI.- z Description 6f Wo'r'.k r. • •4 Alteration Phone#: - City: State: Zip: Square/Linear Footage of Work: ❑ New ❑ Repair/Replace ❑ Demolition r,. i.t'w--•! ..t F. "f7 i� �^-t v' Seir r' '`, .;, •y. . 4if !I(t}� t + _ '�' •. � �+7 .i+f,' i l ",^�,2tiF a, t4';w' Specify color of color ,thrutile: Submittal Fee rY� , -1 rl�'d: s" r ��•s .�' :::,t � :� ' $ �J� }��i . Permit Fee $ _�^ l 5 CCF $ Td•� CO/CC Scanning Fee $ Radon Fee $ `! • 1 3 DBPR $ -I 3 Notary $ Technology Fee $ Training/Education Fee $ • 4y Double Feenp$ 2 Structural Reviews $ Bond $g'1 Ci I - 6 Z.3 TOTAL FEE NOW DUE $ Z5 3 .646 (Revised02/24/2014) Bonding Company's Name (if applicable) Bonding Company's Address City State Mortgage Lender's Name (if applicable) Mortgage Lender's Address City State Zip Zip Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to,meet the standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRIC, PLUMBING, SIGNS, POOLS, FURNACES, BOILERS, HEATERS, TANKS, AIR CONDITIONERS, ETC..... OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. "WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT." Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must promise in good faith that a copy of the notice of commencement and construction lien law brochure will be delivered to the person whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site for the first inspection which occurs seven (7) days after the building permit is issued. In the absence of such posted notice, the inspection will not be approved and a reinspection fee will be charged. i Signature /(' _ y _ Signature OWNER or AGENT The foregoing instrument was acknowledged before me this _ day of ,� )Lloe- 20 I(o by C')Dar �-C 5 WQJ}t.N who is personally known to me or wh as produc FL IX on -F lt, as identification and who did take an oath. NOTARY PUBLIC: CONTRACTOR The foregoing instrument was acknowledged before me this clay of JAI 20J(D by }!«i�or CA✓YA� 4�A who is personally known to me or who has produced or% ({ as identification and who did take an oath. NOTARY PUBLIC: Sign: Sign: Print: i _ Print: Seal: `1OFF",� �''-, Suyapa T. Vasquez Seal: - Commission # FF942611 =� =" = ''-';�;a ',��.•�`' Expires: December 9, 2019 Bonded Aaron Notary-• thru APPROVED BY Plans Examiner Suyapa T. Vasquez mmission # FF942611 fas: December 9, 2019 OAAru Avon, Notary `�•,, Suyapa T. Vasquez rs Commission # FF9C-: "= Expires: December 9• Bonded thru Aaron ************************************* Zoning Structural Review Clerk (Revised02/24/2014) ROOMM AND GENERAL ICOMTRACTOR 10051 SW 43th ST MIAMI FL 33165 PHONE (305)796-6753 EMIAL: HECTOP191 @YAHOO, COM Date: -112 2. 1 1 (1 State of County of Before mi this day Personally appeared ,Aa_\0 being duly sworn, deposes and say: who, That he will be the only person on the project working at .._j1A NEqg !SN%aml IFL 333T Swofn to(4affied) and subscribed before me this Vol day of __djA 1201� by 14t(A'01( Car r'A+'d 0, Personally Know OR It Type of Identification Produced Print, or 4Staaim; of Noj 71 ggbj 1 F�/ SuyW T. Vasquez STATE UCENSE CCC-1328085.,U,, Commission # FF942611 STATE LICENSE CGC-058612 3" Z r 9,2019 Expires December V Bonded thru Aaron Notary% Notice to Owner -- Workers' Corn Miami shores Village Building Department 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 nsation Insurance Exemption Florida Law requires Workers' Compensation insurance coverage under Chapter 440 of the Florida Statutes. Fla. Stat. § 440.05 allows corporate officers in the construction industry to exempt themselves from this requirement for any construction project prior to obtaining a building permit. Pursuant to the Florida Division of Workers' Compensation Employer Facts Brochure. An employer in the construction industry who employs one or more part-time or full -rime employees, including the owner, must obtain workers' compensation coverage. Corporate officers or members of a limited liability company (LLC) in the construction industry may elect to be exempt if: 1. The officer owns at least 10 percent of the stock of the corporation, or in the case of an LLC, a statement attesting to the minimum 10 percent ownership; 2. The officer is listed as an officer of the corporation in the records of the Florida Department of State, Division of Corporations; and 3. The corporation is registered and listed as active with the Florida Department of State, Division of Corporations. No more than three corporate officers per corporation or limited liability company members are allowed to be exempt. Construction exemptions are valid for a period of two years or until a voluntary revocation is filed or the exemption is revoked by the Division. Your contractor is requesting a permit under this workers' compensation exemption and has acknowledge that he or she will not use day labor, part-time employees or subcontractors for your project. The contractor has provided an affidavit stating that he or she will be the only person allowed to work on your project. In these circumstances, Miami Shores Village does not require verification of workers' compensation insurance coverage from the contractor's company for day labor, part-time employees or subcontractors. BY SIGNING BELOW YOU ACKNOWLEDGE THAT YOU HAVE READ THIS NOTICE AND UNDERSTAND ITS CONTENTS. Signature: Owner—, State of Florida County of Miami -Dade The foregoing was acknowledge before me this 30 day of ,LIr W , 201. By C,)nar kCS QA \ktr- who is personally known to me or as produce M as identification. l / Notary: ,,,��' apa'. asquez SEAL: _f iCo mission # FF942611 r 9, 2019 Expires: Decembe Miami shores Village Building Department 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 OWNERS'S AFFIDAVIT OF EXEMPTION ROOF TO WALL CONNECTION HURRICANE MITIGATION RETROFIT FOR EXISTING SITE - BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES PERSUANT TO SECTION 553.844 F.S. To: Miami Shores Village Building Department Date: 10050 NE 2nd Ave Miami Shores, A 33138 Re: Owner's Name: C'k�arlt� Weja *-et' Property Address:6H 1.1E Nkiorvr, SHore� %L Roofing Permit Number: Dear Building Official: certify that I am not required to retrofit the roof to wall connections of my building because: #he just valuation for the structure for purpose of ad valorem taxation is less than $300,000,00, Please attach proof of ad valorem taxation. o The building was constructed in compliance with the provisions of the Florida Building Code (FBC) or with the provisions of 1994 edition of the South Florida Building Code (1994 SFBC) AN/104 Signature State of Florida County of Dade nr e5 IfYr Print Name The undersigned, being the first duly swom, deposes and says that he/she is the owner for the above property mentioned. Swom to and subscribed before me this Notary Public, Sate of Florida at Large of ,jurc 20110 When the just valuation of the structure for purpose of ad valorem taxation is equal to or more than $300,000.00, and Suyapa T. Vasquez Commission if FF942611 Expires: December 9, 2019 Bonded thru Aaron Notary was not constructed with FBC nor a 1994 SFBC. Then you must provide a building application from a General Contractor for the Roof to Wall connection Hurricane Mitigation. Revised on 5121/2009 Property Search Application - Miami -Dade County Page 1 of 1 OFACE OF THE PROPERTY APPRAISER Summary Report Property Information Folio: 11-3206-013-0150 Property Address: 94 NE 93 ST Miami Shores, FL 33138-2816 Owner CHARLES WALTER MARIA PAULA GARCIA Mailing Address ............_......._._..__._..._.._...._._ 94 NE 93RD ST MIAMI, FL 33138 USA PA Primary Zone 1000 SGL FAMILY - 2101-2300 SQ Primary Land Use 0101 RESIDENTIAL - SINGLE FAMILY: 1 UNIT Beds / Baths / Half ^� 3/2/0 Floors 1 Living Units 1 Actual Area 1,943 Sq.Ft Living Area 1,412 Sq.Ft Adjusted Area 1,714 Sq.Ft Lot Size 13,639.68 Sq.Ft Year Built 1940 Assessment Information Year 2016 2015 2014 Land Value $341,301 $258,6591 $258,659 Building Value 84139,177 $141,165 $139,451 XF Value $41,662 $28,201 $28,510 Market Value $522,140 $428,025 $426,620 Assessed Value $431,021 $428,025 L $426,620 Benefits Information Benefit Type 2016 2015 2014 ................. Save Our Homes Cap Assessment Reduction $91,119 Homestead Exemption $25,000 $25,000 $25,000 ................_...................-_.._._.__ Second Homestead Exemption $25,000 $25,000 $25,000 Note: Not all benefits are applicable to all Taxable Values (i.e. County, School Board, City, Regional). Short Legal Description MIAMI SHORES SEC 1 AMD PB 10-70 LOTS 1 & 2 BLK 2 LOT SIZE IRREGULAR COC 24977-2853 09 2006 3 Generated On : 5/16/2017 Taxable Value Information 2016 2015 2014 County Exemption Value $50,000 $50,000 $50,000 Taxable Value $381,0211 $378,0251 $376,620 School Board Exemption Value Taxable Value $25,000 $406,021 $25,000 ._....___... $403,025 $25,000 __............_...................................... $401,620 City Exemption Value $50,000 $50,000 $50,000 Taxable Value $381,021 $378,025 $376,620 __._-._..._.._ m Regional Exemption Value $50,000 $50,000 $50,000 __ Taxable Value -...........___._.._.__...__.. $381,021 _______.�®_ $378,025 _..-_............ $376,620 Sales Information Previous Sale Price OR Book -Page Qualification Description 05/07/2013 $550,000 28623-0609 Qual by exam of deed 09/01/2001 $267,000 19923-4609 Sales which are qualified 03/01/1998 $128,000 18047-3730 Sales which are qualified 08/01/1996 $80,000 17314-1896 Sales which are qualified The Office of the Property Appraiser is continually editing and updating the tax roll. This website may not reflect the most current information on record. The Property Appraiser and Miami -Dade County assumes no liability, see full disclaimer and User Agreement at http://www.miamidade.gov/info/disclaimer. asp Version http://www.miamidade.gov/propertysearch/ 5/16/2017 . RT-_ 11 - )336 SECTION R4402.14 RECEIVE D HIGH VELOCITY HURRICANE ZONES — UNIFORM PERMIT APPLICATION ' MAY 16 2017 Florida Building Code Edition 2010 High Velocity Hurricane Zone Uniform Permit Application Form INSTRUCTION PAGE COMPLETE THE NECESSARY SECTIONS OF THE UNIFORM ROOFING PERMIT APPLICATION FORM AND ATTACH THE REQUIRED DOCUMENTS AS NOTED BELOW: Roof System Required Sections of the Attachments Required Permit Application Form See List Selow • • • •' Low Slope Application A,B,C 1,2,3,4,5,frZ.. • Prescriptive BUR-RAS 150 A,B,C 4,5,6,7 •••.•• :...;. ...... Asphaltic Shingles A,B,D 1,2,4,5,6,7 •• •. Concrete or Clay Tile A,B,D,E 1.2.3.4.F,637. ' Metal Roofs A,B,D 1,2,3,4,5,6,7 •• Wood Shingles and A,B,D 1,2,4,5,6,7 Shakes Other As Applicable 1,2,3,4,5,6,7 ATTACHMENTS REQUIRED: 1. Fire Directory Listing Page 2. From Notice Of Acceptance: Front Page Specific System Description Specific System Limitations General Limitations Applicable Detail Drawings 3. Design Calculations per Section R4403, or If Applicable, RAS 127 or RAS 128 4. Other Component Notice of Acceptances 5. Municipal Permit Application 6. Owners Notification for Roofing Considerations (Re -Roofing Only) 7. Any Required Roof Testing Calculation Documentation Att Florida Building Code Edition 2010 High Velocity Hurricane Zone Uniform Permit Application Form Section C (Low Sloped Roof System) Fill in Specific Roof Assembly Components and Identify Manufacturer (If a component is not used, identify as "NA") System Manufacturer: NOA No.: Design Wind Pressures, From RAS 128 or Calculations: Pmax1: Pmax2: Pmax3: Max. Design Pressure, Fr a Specific NOA System: Deck: Type: Gauge/Thickness: Slope: Anchor/Base Sheet & No. of Ply(s): Anchor/Base Sheet Fastener/Bonding Material: Insulation Base Layer: Base Insulation Size and Thickness: Base Insulation Fastener/Bonding Material: Fastener Spacing for Anchor/Base Sheet Attachment Field: " oc @ Lap, # Rows @ " oc Perimeter: " oc @ Lap, # Rows " oc Corner: ° oc Ca) Lap, #Rows C " oc Number of Fasteners Pe nsulation Board Field: Perimete • • Corner ....' • • • • ...... . : V • • . ..... Illustrate Com onents lygi�ed and ...... Details as Ap icable: ....' • • • % • • • • • • oodblocking, Gutter, �ci�g�a. Terniin ation, •••••� tripping, Fla ing, Co t Cleal,, .ant ' • • • • trip, Base Flashing, au tier- Flashing, '•••�• Coping, Etc. • Indicate: can Roof Hei ht, Para •44eight, "••�• Height of Base Flashing, Gemponent.j� terial • Material Thickness, Fast ner Type, Fay ner p • Spacin or Submit Manuf cturersDetails •th Com v with RAS 111 and Cha er 16. Top Insulation Layer: FT Parapet Top Insulation Size and Thickness: Height Top Insulation Fastener/Bonding Material: Base Sheet(s) & No. of Ply(s): Mean Base Sheet Fastener/Bondin aterial: Roof Height Ply Sheet(s) & No. of PI s): Ply Sheet Fastene onding Material: Top Ply: Top Fastener/Bonding Material: Florida Building Code Edition 2010 High Velocity Hurricane Zone Uniform Permit Application Form Section D (Steep Sloped Roof System) Roof System Manufacturer: CROWN BUILDING PRODUCTS OF FLORIDA, LLC Product Approval Number: 14-1006.02 Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations): P1:47.6 P2:100.6 P3:100.6 Maximum Design Pressure Product Approval Specific System. 45.5 19000 go,• 'Poe* Method of Tile Attachment: ICP ADHESIVES POLYSET AH-160 • • • • • • ;•; ...... Steep Sloped System Description Deck Type: Roof Slope: 3 : 12 Ridge Ventilation? to match existing 5/8 INCH PLYWOOD Underlayment: Mean Roof Height: 141 lation: . ,go ASTM D 226 TYPE II #30 N/A re Barrier: N/A Fastener Type &Spacing: 1 1/4" R.S. CORROSION RESISTANT give Type: ICP ADHESIVES POLYSET AH-160 Type Cap Sheet: POLYGLASS POLYSTICK (PEEL & STICK) Roof Covering: Tuscany Roof Tile (Color-Thru) Type & Size Drips Edge: 3 INCH 26 GAUGE1 0% Florida Building Code Edition 2010 High Velocity Hurricane Zone Uniform Permit Application Form Section E (Tile Calculations) For Moment based tile systems, choose either Method 1 or 2. Compare the values for Mr with the values from K. If the Mr values are greater than or equal to the Mr values, for each area of the roof, then the tile attachment method is acceptable. Method 1 "Moment Based Tile Calculations Per RAS 127" (Pt: 47.6 X a .313 14.90 ) - M9: 6.99 Mri 7.91 Product Approval Mf 45.5 (P2: 100.6 X .313 = 31.49 ) _ Mg: 6.99 _ Mr2 24.50 Product Approval Mf 45.5 (P3: 100.6 X .313 _ 31.49 } _ M9: 6.99 = Mr3 24.50 Product Approval Mf 45.5 Method 2 "Simplified Tile Calculation Per Table Below" • • • • Required Moment of Resistance (Mr) From Table Below Product App1=ftI1V1100000. • • M Re uired Moment Resistance" •""' • Mean Roof Height -♦ Roof Slope 15' 20' 25' • • 30' • • • : • .. 40' 2:12 34.4 36.5 38.2 39.7 ' • ..' •12 32.2 34.4 36.0 37.4 • • 39.8 • 4:1 30.4 32.2 33.8 35.1 • 37 • - 5:12 28.4 30.1 31.6 3Zf" 34A • 6:12 26.4 28.0 29.4 30.5 32.4 • 7:12 24.4 25.9 27. 28.2 30.0 'Must be used in conjunction with a i f moment based ' systems endorsed by the Broward County Board of Rules and App Is. For Uplift based tile systems use Method 3. mpare the values for F' with the values for Fr. If the F' values are greater than or equ o e Fr values, for each area of the roof, then the the attachment method is acceata Method 3 "U Based Tile Calculation er RAS 127" (P,: x 1: = x w:- _) - W: x cos 0: - = Fr, Product Approval F' (Pz: x 1: _ _ _� - W: x cos 0: - -F duct Approval F (P3: x 1: = x W.: _� - W: x cos 0: - = Fr3 Pro pproval F Where to Obtain Information Description Symbol Where to find Design Pressure P1 or P2 or P3 RAS 127 Table 1 or by an engineering analysis prepared by PE based on ASC Mean Roof Height H Job Site Roof Slope 0 Job Site Aerodynamic Multiplier A Product Approval Re oring Moment due to Gravity Ma Product Approval Attachment Resistance Mf Product Approval Required Moment Resistance M, Calculated Minimum Attachment Resistance F Product Approval Required Uplift Resistance F, Calculated Average Tile Weight W Product Approval Tile Dimensions I = length w = width Product Approval All calculations must be submitted to the Building Official at the time of permit application. • 4NUR� 7 F'�ORi�Un SECTION 1524 HIGH VELOCITY HURRICANE ZONES REQUIRED OWNERS NOTIFICATION FOR R ROOFING 1524.1 Scope. As it pertains to the section, it is the responsibility of roofing contractor to provide the owner JNith the required roofing permit, and to explain to the owner the content of the section. The provisions of Section 134402 govern the minimum requirements and standards of the industry for roofing system installations. Additionally, the following items should be addressed as part of the agreement between the owner ant the contractor. The owner's initial in the designated space indicates that the item has been explained. 2. ... Renailing wood decks: When replacing roofing, the existing woad rodf deck roaX.oo to • . (The is us��ll� be renailed in accordance with the current provisions of Section R4403; .. •.•. concealed prior to removing the existing roof system). •..%. 4. _.�_---- _--Exposed Ceiling: Exposed, Open beam ceilings are where the uric%rMe of tt� U%eckin ••oo• can be viewed from below. The owner may wish to maintain the architectural .appearance; the�efo�'e, g•••. • roofing nail penetration of the underside of the decking may not be acceptablThisprovide�s the optinn of••'. • maintaining the appearance. 6. •• --4 _—Overflow scuppers (wall outlets): It is required that rainwater flows off so that the ero�of is not overloaded from a buildup of water. Perimeter/ed discharge if overflow scuppers (wall outletsge wall or other roof extension may block this ) are not provided. It may be necessary to install overflow scuppers in accordance with the requirements of Sections R4402#Signa�ture R4403 and I,1413. Owner/Agent's Signature Date --" Con� - Date 9y NE 613 513 a.i R A__arn ��CreS Property Address Permit Number Revised on 7/9/2009 LD,07/01/2015; � r O MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miarrn, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.eov/economy ICP Adhesives and Sealants, Inc. 12505 NW 44"' Street Coral Springs, FL. 33065 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the rigtt to hare, bis product': • or material tested for quality assurance purposes. If this product or material fails to perforn? ft? Me accepts n t' nner.#Le* � • manufacturer will incur the expense of such testing and the AHJ may immediately revoke,* Mddi'fy, or suspend the•use of such product or material within their jurisdiction. RER reserves the right to rev0%%.tills acc fie, if f �3'': determined by Miami -Dade County Product Control Section that this product or material fails4 meet the requiretmt;ta•0 of the applicable building code. • • � • .' • • This product is approved as described herein, and has been designed to comply wits tb; Plorida Building Code• including the High Velocity Hurricane Zone of the Florida Building Code. ...:. • •:. DESCRIPTION: ICP Adhesives Polysee AH-160 LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA 16-0315.01 and consists of pages 1 through 11. The submitted documentation was reviewed by Alex Tigera. ridffl,06� _� NOA No.: 17-0322.03 Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 1 of 11 ROOFING COMPONENT APPROVAL: Category: Roofing Sub Category: Roof tile adhesive Materials: Polyurethane SCOPE: This approves ICP Adhesives Polyset® AH-160 as manufactured by ICP Adhesives and Sealants, Inc. as described in this Notice of Acceptance. For the locations where the design pressure requirements, as determined by applicable building code, do not exceed the design pressure values obtained by calculations in compliance with Roofing Application Standard RAS 127. For use with approved flat, low, and high profile roof tile systems using ICP Adhesives Polyset® AH-160. PRODUCTS MANUFACTURED BY APPLICANT: Product Dimensions Test Product Description Specifications ICP Adhesives N/A TAS 101 Two component polyurethane f9w adhesive Polyset®AH-160 00. •....' .. • . ... ICP Adhesives Foam N/A Dispensing Equipmppl • . • • • Dispenser RT71000 ' ICP Adhesives ProPack® N/A Dispensing Equipment • .... . ..... ...... 30 & 100 .. .. .. . ...... PRODUCTS MANUFACTURED BY OTHERS: • • • • : • Any Miami -Dade County Product Control Accepted Roof Tile Assembly having a current WO gwhiclaJist attachrpento •; resistance values with the use of ICP Adhesives Polyset® AH-160 roof tile adhesive. • •: MANUFACTURING LOCATION: 1. Tomball, TX. PHYSICAL PROPERTIES: Property Test Results Density ASTM D 1622 1.6 lbs./ft 3 Compressive Strength ASTM D 1621 18 PSI Parallel to rise 12 PSI Perpendicular to rise Tensile Strength ASTM D 1623 28 PSI Parallel to rise Water Absorption ASTM D 2127 0.08 Lbs./Ft2 Moisture Vapor Transmission ASTM E 96 3.1 Perm / Inch Dimensional Stability ASTM D 2126 +0.07% Volume Change @ -400 F., 2 weeks +6.0% Volume Change @158°F., 100% Humidity, 2 weeks Closed Cell Content ASTM D 2856 86% Note: The physical properties listed above are presented as typical average values as determined by accepted ASTM test methods and are subject to normal manufacturing variation. NOA No.: 17-0322.03 MIAMI•DADE COUNTY Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 2 of 11 EVIDENCE SUBMITTED: Test Aeency Center for Applied Engineering Miles Laboratories Polymers Division Ramtech Laboratories, Inc. Southwest Research Institute Trinity Engineering Celotex Corp. Testing Services Test Identifier #94-060 257818-IPA 25-7438-3 25-7438-4 25-7438-7 25-7492 NB-589-631 9637-92 01-6743-011 01-6739-062b[ 1 ] 7050.02.96-1 P36700.04.12 P39740.02.12 528454-2-1 528454-9-1 528454-10-1 520109-1 520109-2 520109-3 520109-6 520109-7 520191-1 520109-2-1 Test Name/Renort TAS 101 TAS 101 SSTD 11-93 SSTD 11-93 SSTD 11-93 ASTM D 1623 ASTM E 108 ASTM E 108 ASTM E 84 TAS 114 :�•.'- ASTM D 1623 ...... TAS 101 ...%. TAS 123 •••• TAS 101 TAS 101 TAS 101 Date 04/08/94 12/16/96 10/25/95 11 /02/95 12/12/95 02/01 /94 04/30/93 11/16/94 01/16/95 • M7f4/96 •.0.a'ri /12 '. 02J21/12 • . ..... . ...... . *r=/98 :'t2;M/98 03/02/99 LIMITATIONS: 1. Fire classification is not part of this acceptance. Refer to the Prepared Roof Tile Assembly for fire rating. 2. ICP Adhesives Polyset`' AH-160 shall solely be used with flat, low, & high tile profiles. 3. Minimum underlayment shall be in compliance with the Roofing Application Standard RAS 120. 4. Roof Tile manufactures acquiring acceptance for the use of ICP Adhesives Polyset® AH-160 roof the adhesive with their tile assemblies shall test in accordance with TAS 101. 5. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61G20-3 of the Florida Administrative Code. NOA No.: 17-0322.03 MIMMADeCOU Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 3 of 11 INSTALLATION: 1. ICP Adhesives Polyset® AH-160 may be used with any roof tile assembly having a current NOA that lists attachment resistance values with the use of ICP Adhesives Polyset'' AH-160. 2. ICP Adhesives Polyset® AH-160 shall be applied in compliance with the Component Application section and the corresponding Placement Details noted herein. The roof tile assembly's adhesive attachment with the use of ICP Adhesives Polyset® AH-160 shall provide sufficient attachment resistance to meet or exceed the resistance value determined in compliance with Miami -Dade County Roofing Application Standards RAS 127. The adhesive attachment data is noted in the roof tile assembly NOA. 3. ICP Adhesives Polyset® AH-160 and its components shall be installed in accordance with Roofing Application Standard RAS 120, and ICP Adhesives and Sealants, Inc.'s Operating Instruction and Maintenance Booklet. 4. Installation must be by a Factory Trained 'Qualified Applicator' approved and licensed by ICP Adhesives and Sealants, Inc. ICP Adhesives and Sealants, Inc. shall supply a list of approved applicators to the authority having jurisdiction. 5. Calibration of the ICP Adhesives Foam Dispenser RTF 1000 dispensing equipment is required before application of any adhesive. The mix ratio between the "A" component and the "B" component shall be maintained between 1.0-1.15 (A): 1.0 (B). sees . . sees sees.. 6. ICP Adhesives Polyset' AH-160 shall be applied with ICP Adhesives Foam DispenserRT;F1000 or�fP Adhesives ProPack' 30 & 100 dispensing equipment only. "' •' • .. sees.* o sees. •. 7. ICP Adhesives Polyset® AH-160 shall not be exposed permanently to sunlight. e e e e ; • • • • • sees.. 8. Tiles must be adhered in freshly applied adhesive. Tile must be set within 1 to 2 minutes after ICP Adhesives • • • Polyset® AH-160 has been dispensed. • .. .. .. . sees.. 9. ICP Adhesives Polyset® AH-160 placement and minimum patty weight shall be in Wftd4nce with the • • 'Placement Details' herein. Each generic tile profile requires the specific placement notedliereitt...:. • • • • • • • . s .sees. NOA No.: 17-0322.03 Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 4 of 11 Table 1: Adhesive Placement For Each Generic Tile Profile Tile Profile Placement Detail Minimum Paddy Contact Minimum Paddy Gram Area Weight Eave Course - Flat, Low, High All Eave Course 17-23 sq. inches 45-65 Profiles Flat, Low, High Profiles #1 17-23 sq. inches 45-65 Flat Profile #2 10-12 sq. inches 30 Low Profile #2 12-14 sq. inches 30 High Profile #2 17-19 sq. inches 30 Flat, Low, High Profiles #3 Two Paddys: 8-9 sq. inches at 12 grams per paddy head of tile 9-11 sq. inches at overlap Two -Piece Barrel (Cap Tile) Two Piece 2 Beads (1 each longitudinal 17 grams per bead edge) 20-25 sq. inches each bead 0*00 • Two Piece Barrel (Pan Tile) Two Piece 65-70 sq. inches ... .. 34 gibs T* der pan • .... ...... .... . ..... LABELING: ...... .. All approved products listed herein shall be labeled and shall bear the imprint or identifiabte rittrking of -the ...... manufacturer's name or logo and following statement: "Miami -Dade County Product ContsdrA%roved" of the Miami Dade County Product Control Seal as shown below. :... :. ****go Mwrn�►o� courm • • • • • • BUILDING PERMIT REQUIREMENTS: As required by the Building Official or applicable building code in order to properly evaluate the installation of this system. NOA No.: 17-0322.03 Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 5 of 11 ADHESIVE PLACEMENT DETAIL # 1 Mail thr"h plastic ceen.nt Paddy Mon.ath Tips) (whentoyulted) s 10 Ilk ` Battens option �. Ew. Closure d Hail through plastic cement lwhen required) \ �A Paddy 1 4Mth TRIO I. tMdariaytrwnt 101n.x Batters optional tare Closure tiara Course `. ' casaa to through plastic M c++, W dwhenrequiredl f {Paddy lUnrmthVial t 10in.a 2 in. wade Battens optional CAN" count 'd a weepf l 10Im 21 Env closure /� Drip *do* APPROVED Flat/Low Profile Tile 1. Starting at the eave course, apply a minimum 2" (50.8 mm) x 10" (254 mm) x 1" (25.4 mm) foam paddy onto the underlayment positioned as shown, under the strengthening rib closest to the overlock of the tile being set. 2. Continue in same manner. Insure approximately 17 (109.7 cm2) — 23 (148.4 cm2) square inch adhesive contact with the underside of the tile. Medium Profile / Double Pan Tile 1. Starting at the eave conrseJ apply a "vAum 2 ...... (50.8 mm) x 10" (254 nun) x 1" (254pan) foam paddy onto the underla3hi bI positietfedas shown•: • under the pan portion off' W file closest to the overlock of the tile beir� s;t • ... • . • • ..... 000000 of** 2. Continue in same mamtext Insure app?b4matejx J 7.. (109.7 cm2) — 23 (148;4 tWj square inch adhesive • contact with the underside Of the 4Le, , ; , • • • • • . .. High Profile / Single Pan Tile 1. Starting at the eave course, apply a minimum 2" (50.8 mm) x 10" (254 mm) x 1" (25.4 mm) foam paddy onto the underlayment positioned as shown under the pan portion of the tile closest to the overlock of the tile being set. 2. Continue in same manner. Insure approximately 17 (109.7 cm2) — 23 (148.4 cm) square inch adhesive contact with the underside of the tile. NOA No.: 17-0322.03 Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 6 of 11 ADHESIVE PLACEMENT DETAIL ## 2 #ail ehrov¢h platti+n c�rnrnt � P►ddy iRarauth'ral�) UrAdac,l ymarot Rattans optional � '� ,� .r,`> IOin\ . f 1 ``'✓+ Ewe Closure •._„�..� ¢ d,,,✓' "I through plastic cement twlren rertuaredl Paddy 4ReneathTile) 71 Battens optional M�49 ` � Iwati�cibvr, Etv. Coon• \ fate%& Flat/Low Profile Tile Starting at the cave course, apply a minimum 2" (50.8 mm) x 10" (254 mm) x 1" (25.4 mm) foam paddy onto the underlayment positioned as shown under the strengthening rib of the the closest to the overlock of the tile being set. Insure approximately 17 (109.7 cm') — 23 (148.4 cmZ) square inch adhesive contact with the underside of the tile. 2. At the second course, apply a minimum 2" (50.8mm) x 7" (177.8 mm) x 1" (25.4 mm) foam paddy onto the underlayment positioned as shown under the strengthening rib closest to the overlock of the file being set. 3. Continue in same manner. Insure approximately 10" (64.5 cm) - 12 (77.4 cmZ) square inc4'atlhb8 ive contact with the undersideagfit%e tile. "' • • • . . a ...... .. . ...... Medium Profile / Double PgngNf :"• •; .... . ..... • 1. Starting at the cave cour�eJ$F y a n0t4ftn 2" (050:6• mm) x 10" (254 mm) x la'; (;a.4 nun) %am paddy " • ; • onto the underlayment p4sitto4ed as , howgi under the a a pan portion of the file closest -to the dVdi'iddk of the rile being set. Insure apprblunntely i i (109.7 cnfj •- 23 (148.4 cmZ) square inch adhesive contact with the underside of the tile. 2. At the second course, apply a minimum 2" (50.8mm) x 7" (177.8 mm) x 1" (25.4 nun) foam paddy onto the underlayment positioned as shown under the pan portion of the tile closest to the overlock of the tile being set. 3. Continue in same manner. Insure approximately 12" (77.4 cm2) -14 (90.3 cmZ) square inch adhesive contact with the underside of the tile. (Instructions continued on next page) NOA No.: 17-0322.03 Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 7 of 11 ADHESIVE PLACEMENT DETAIL ## 2 (CONTINUED) uaii tlw� P#"t'k c• Cwh•nF'WWIr•d? paddyriMnn d+Tll•) ' 2 in. �64 - Famis Win, in, 2 in. the deswe brip •dpe High Profile / Single Pan Tile 1. Starting at the eave course, apply a minimum 2" (50.8 mm) x 10" (254 mm) x 1" (25.4 mm) foam paddy onto the underlayment positioned as shown under the pan portion of the tile closest to the overlock of the tile being set. Insure approximately 17 (109.7 cm) — 23 (148.4 cm') square inch adhesive contact with the underside of the tile. 2. At the second course, apply a minimum 2" (50.8mm) x 7" (177.8 mm) x 1" (25.4 mm) foam paddy onto the underlayment positioned as shown under the pan portion of the tile closest to the overlock of the tile being set. 3. Continue in same manner. Insure approximately 17" (109.7 cm2) - 19 (122.6 c n).square inch Udhesive • • • • • . • contact with the underside of the tile... . ... • • ...... #00 NOA No.: 17-0322.03 Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 8 of 11 ADHESIVE PLACEMENT DETAIL ## 3 NaH dlmAcirbr�d)�went (�+reeatks) (whsattens op4ionai Paddy omder die) modde 4 x 4 [n.`` 2x41n. 10 Gs 2 Em closure Rat/Low Prattle Tile 7� 11MM0711daffn APPROVED 1. On the cave course only, apply a minimum 2" (50.8 mm) x 10" (254 mm) x 1" (25.4 nun) foam paddy onto the underlayment positioned as shown, under the strengthening rib for flat tile or under the pan portion of the tile for low or high profile tile closest to the overlock of the tile being set. Leave approximately 4" (101.6 mm) up from the cave edge free of foam to prevent the expanded adhesive from blocking the weep holes. Insure approximately 17-23 in' (109.7-148.4 cm) of adhesive contact with the underside of the tile 2. Apply a 4" (101.6 mm) x 4" (101.6 mm) x 1 " (25.4 mm) foam paddy onto the underlayment just below the second course line positioned foam paddy under the strengthening rib for flat tile, pr under the pan portion of the the„ clojgt to t1ie•underlock.Av1. •. the second course tile td be ihstallgd. tWe approximately 8-9 inZ IM;(M.1 crA) of adhegivv' contact with the undersl4� p the tile. ; • .... . ..... (Instructions continued Olt fiexlpage) • • ...... NOA No.: 17-0322.03 Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 9 of 11 ADHESIVE PLACEMENT DETAIL # 3 (CONTINUED) MAdfroagho"* Siagiepaftundadle 4when Freiufre� Paddy ibrtweet► tiirs} GOO Paddy (under cF1e} Si "* 4xiin. 2xs top of ule Enft �. YVeephok 10},,. 2}n. 6aredosum Drfp edify Htg!► ProfileT& 3. Also apply a 2" (50.8 mm) x 4" (101.6 mm) x 3/4" (19 mm) paddy on top of the eave course tile surface as shown, on top of the strengthening rib for flat tile or on top of the pan portion of the tile, closest to the underlock of the first course of tile. Install second course of tile. Insure approximately 9 (58.1 cm2) - 11 (71cm2) square inch adhesive contact with the underside of the tile at the overlap and 7 (45.2 cmZ) - 9 (58.1 cm2) square inch adhesive contact with the underside of the tile at the head of the tile. Continue in same manner. .... . ..... .. .. .. . ...... %09% ...... .. . ... . .609% NOA No.: 17-0322.03 MAWDADE COUNTY Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 10 of 11 t) Place enough adhesive to achieve 65 to 70 a in contact with the pan tile. 2) Turn covers upside down. Place adhesive in to 1 in. from outside edge of cover tile. Then install the tile. Ensure 20 to 25 s%In. contact area. -y c Underlayment Eon closure (motar shown) Fascia ADHESIVE PLACEMENT DETAIL TWO PIECE BARREL Steep pitch applications (when required) Remove top portion of the save course cover the Abut to second course of pan tiles. Ensure ewe end of pan and cover tiles are flush at eave line. Two Piece Barrel - High Profile Tile Two Piece Barrel (Cap and Pan) Tile 1. Starting at the eave course, apply a minimum 2" (50.8 mm) x 10" (254 mm) x 1" (25.4 mm) foam paddy onto the underlayment positioned as shown under two adjacent pan tiles. Support eave tiles from rocking until adhesive has a chance to cure. 2. Continue in same manner bringing two pan courses up toward the ridge. Insure approximately 65 (419.4 cmZ) — 70 (451.6 cm) square inch adhesive contact with the underside of the pan tile. 3. Turn covers upside down exposing the underside of the tile. Apply a minimum 1" (25.4 mm) x 10" (254 nun) bead of adhesive direatf} b%the inner edge of each side ot'tlVjgver tile,' I *av e approximately 3/4" (19 a=) to t ; J25;I nun) • • ,' • from the outside edge 44he tile, inward, free of • foam to allow for eX11trMpn. • : • • • • • .. .. e 4. Turn cover tile over i t; r* loam is alil3Ged anti• • • • place onto pan tile wu . Insure a minimum oY: • 20 (129 cmZ) - 25 (; 61 � i�mZ) square inch • • � • contact area on each side pf the cover the to the 000000 pan tile. Continue in•stme manner. Trim away any cured exposed foam adhesive. PtAnting of longitudinal edges of the cover tiles are considered optional. S. When additional nailing is required, 2" (50.8 mm) x 4" (101.6 mm) nailers or the tie wire system using galvanized, stainless steel, or copper wire and compatible nails may be used. END OF THIS ACCEPTANCE NOA No.: 17-0322.03 Expiration Date: 05/10/22 Approval Date: 04/27/17 Page 11 of 11 mmmbk MIAMFQADE * MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.2ov/economy Polyglass USA Inc. 1111 W. Newport Center Drive Deerfield Beach, FL 33442 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to wW4 the requirements of the applicable building code. s • • • • • . •' goose* This product is approved as described herein, and has been designed to comply with the Flcrtda Suildin fojie • including the High Velocity Hurricane Zone of the Florida Building Code. e' • • • • • • • go ...... .... :so**: DESCRIPTION: Polyglass Polystick Underlayments • • . o .' ; g • • 0 • 0 s s • e g • . •.... LABELING: Each unit shall bear a permanent label with the manufacturer's name or lobo �dity, state and fellowi V o:. statement: "Miami -Dade County Product Control Approved", unless otherwise noted heron. • • RENEWAL of this NOA shall be considered after a renewal application has been filed and• 1hare has been po chi • in the applicable building code negatively affecting the performance of this product. •.: TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews and revises NOA No.14-0717.08 and consists of pages 1 through 8. The submitted documentation was reviewed by Gaspar J Rodriguez. 44 NOA No.: 15-0410.04 Expiration Date: 09/13/21 Approval Date: 08/11/16 Page 1 of 8 ROOFING COMPONENT APPROVAL Cateeory Roofing Sub-Cateeory: Underlayment Material: SBS , APP Self -Adhering Modified Bitumen PRODUCTS DESCRIPTION: Test Product Product Dimensions Specification Description Polystick IR-Xe 65' x 3'33/s" ASTM D 1970 A fine granular/sand top surface self -adhering, APP Manufacturing Or 65' x 3' polymer modified, fiberglass reinforced, bituminous Location #1 & #2 60 mils thick sheet material for use as an underlayment in sloped roof assemblies. Designed as an ice & rain shield. Polystick Dual Pro 61' x 313/8" TAS 103 and A rubberized asphalt self -adhering, glass-fiber/polyester Manufacturing 60 mils thick ASTM D 1970 reinforced waterproofing membrane. Designed as a Location #2 metal roofing and roof tile underlayment. Polystick Tile Pro 61' x 3'3 3/8" TAS 103 and A rubberized asphalt self -adhering, glass-fiber/polyester Manufacturing 60 mils thick ASTM D 1970 reinforced waterproofing membrane. Designed as a metal Location #2 roofing and roof file underlayment. • • • • • Polystick TU Max 65'8" x 3'3-3/8" TAS 103 and A rubberized asphalt self-adr'ng, polyectarowinforced• • Manufacturing 60 mils thick ASTM D 1970 waterproofing membrane. 15ego*d as a epro& tile ....:. ...... Location #1 & #2 underlayment. • .... ...... Polystick TU P 32'10" x 3'33/8" TAS 103 and A rubberized asphalt waterpibMg mei;brane, glass. • • • Manufacturing 130 mils thick ASTM D 1970 fiber/polyester reinforced, UWa granul %Race • • � • • • • • • • • • Location #2 designed for use as a tile ropf �erlayment.- •' • •.' Polystick TU Plus 65' x 3'3- 8" TAS 103 and A rubberized asphalt self-aii 0 0, glas••s.fibh/polyCst�2' • (Surface Printing) 80 mils thick ASTM D 1970 reinforced waterproofing nfwbrVc. Dgfigned as a66t-ali Manufacturing roofing and roof file underlayment. •. Location #1 & #2 Polystick MTS 65'8" x 33 3/g" TAS 103 A homogeneous, rubberized asphalt waterproofing Manufacturing 60 mils thick membrane, glass fiber reinforced with polyolefinic film Location #2 on the upper surface for use as an underlayment for metal roofing, roof tile, slate tiles and shingle underlayment. Polystick MTS Plus 6518" x 3133/8" TAS 103 A homogeneous, rubberized asphalt waterproofing Manufacturing 60 mils thick membrane, glass fiber reinforced with polyolefinic film Location #2 on the upper surface for use as an underlayment for metal roofing, roof tile, slate tiles and shingle underlayment. Elastoflex S6 G 32'10" x 33 %" TAS 103 and Polyester reinforced, SBS modified bitumen membrane Manufacturing ASTM D 6164 with a sanded back face and a granule top surface. For Location #2 use in roof tile underlayment systems. NOA No.: 15-0410.04 � ! Eta . Expiration Date: 09/13/21 UivjoApproval Date: 08/11/16 Page 2 of 8 MANUFACTURING PLANTS: 1. Hazelton, PA 2. Winter Haven, FL Test Agency Trinity I ERD PRI Asphalt Technologies Momentum Technologies, Inc. LABELING: EVIDENCE SUBMITTED Test Identifier Test Name/Report Date P10870.09.08-R1 P 10870.04.09 P33360.06.10 P33370.03.11 P33370.04.11 P36900.09.11 P37300.10.11 P40390.08.12-2 P37590.07.13-1 P45270.05.14 P46520.10.14 P44360.10.14 P43290.10.14 PLYG-SC 10130.06.16-3 PLYG-10130.06.16-1 PUSA-035-02-01 PUSA-055-02-02 PUSA-089-02-01 TAS 103 TAS 103/ASTM D4798 & G155 ASTM D1970 TAS 103 ASTM D 1623 TAS 103/ASTM D4798 & G155 TAS 110/ASTM D4798 & D 1970 ASTM D 1623 ASTM D6164 TAS 103, TAS 110 & ASTM D1623 ASTM D1623 TAS 103 & TAS 110 ASTM D 1970 & TAS 110 TAS 103 & TAS 110 ASTM D1970 & TA$ 110• TAS 103 ' TAS 103 TAS 103/ASTM D4798 &Z 55 JX20H7A TAS 103/ASTM D4798'&:M5 RX14E8A TAS 103/ASTM D479e& U155 DX231)8B TAS 103/ASTM D479$& fik55 DX23D8A TAS 103/ASTM D4799 & G155 .. 12/04/08 04/13/09 07/01/10 03/02/11 04/26/11 09/01 /11 10/19/11 08/07/12 07/02/13 05/12/14 10/03/14 10/07/14 10/17/14 06/27/16 • : •'66/27/16 .... ...... :62/29/06 •, • • 12/10/07' • 97/06/+ • • - • ..... • • 101/09/09 • •: • 02/18/10 ...:02/18/ 140*0 .... ...... 1. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo, city and state of manufacturing facility and the following statement: "Miami -Dade County Product Control Approved" or the Miami -Dade County Product Control Seal as shown below. BUILDING PERMIT REQUIREMENTS: Application for building permit shall be accompanied by copies of the following: 1. This Notice of Acceptance. 2. Any other documents required by the Building Official or applicable building code in order to properly evaluate the installation of this materials. NOA No.: 15-0410.04 Expiration Date: 09/13/21 Approval Date: 08/11/16 Page 3 of 8 INSTALLATION PROCEDURES: Deck Type 1: Wood, non -insulated Deck Description: Min. 19/32" plywood or wood plank System Type E(1): Anchor sheet mechanically fastened to deck, membrane adhered Anchor/Base Sheet: One or more plies of ASTM D 226 Type II or ASTM D 2626. Fastening: Per FBC 1518.2 & 1518.4 Nails and tin caps 12" grid, 6" o.c. at a minimum 4" head lap. (for base sheet only) Membrane: Polystick IR-Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU Plus, Polystick MTS or Polystick MTS Plus, self -adhered. Surfacing: See General Limitations Below. Deck Type 1: Wood, non -insulated Deck Description: Min. 19/32" plywood or wood plank System Type E(2): Anchor sheet mechanically fastened to deck, membrane adhered Anchor/Base Sheet: One or more plies of ASTM D 226 Type II or ASTM D 2626. Fastening: Per FBC 1518.2 & 1518.4 Nails and tin caps 12" grid, 6" o.c. at a minimum 4" head lap. (for base sheet only) • • • • Membrane: .... Elastoflex S6 G, hot asphalt applied .. . . • • • Surfacing: See General Limitations Below. • • •: • • • • • ....:. .... ...... Deck Type 1: .... . ..... Wood, non -insulated .... �. Deck Description: Min. 19/32" plywood or wood plank " • • • System Type E(3): Base sheet mechanically fastened to deck, subsequent cap tneiht:rane Self jadhered •:: • • • • • • . Anchor/Base Sheet: One or more plies of ASTM D 226 Type H or ASTM D 2626.: 0 *: • Fastening: Per FBC 1518.2 & 1518.4 Nails and tin caps 12" grid, 6" o.c. at a minimum 4"Held lap. (for base sheet only) Ply Sheet: Polystick MTS Plus, self -adhered with minimum 3" horizontal laps and minimum 6" vertical laps. Membrane: Polystick TU Plus, self -adhered. Surfacing: See General Limitations Below. NOA No.: 15-0410.04 °E C Expiration Date: 09/13/21 Approval Date: 08/11/16 Page 4 of 8 INSTALLATION REQUIREMENTS: 1. All nails in the deck shall be carefully checked for protruding heads. Re -fasten any loose deck panels, and sweep the deck thoroughly to remove any dust and debris prior to application. 2. Place the underlayment over metal drip edge in accordance with RAS 111. 3. Place the first course of membrane parallel to the eave, rolling the membrane to obtain maximum contact. Remove the release film as the membrane is applied. All side laps shall be a minimum of 3-%" and end laps shall be a minimum of 6". Roll the membrane into place after removing the release strip. Vertical strapping of the roof with Polystick is acceptable. Membrane shall be back nailed in accordance with applicable building code. 4. When applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane from the center outward in both directions. 5. For ridge applications, center the membrane and roll from the center outward in both directions. 6. Roll or broom the entire membrane surface so as to have full contact with the surface, giving special attention to lap areas. 7. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control Notice of Acceptance. 8. All protrusions or drains shall be initially taped with a 6" piece of underlayment. The flashing tape shall be pressed in place and formed around the protrusion to ensure a tight fit. A second layer of Polystick shall be applied over the underlayment. GENERAL LIMITATIONS: ' • •' ... , • 1. Fire classification is not part of this acceptance. " ""'. 2. Polystick Dual Pro, Polystick Tile Pro, Polystick TU Plus, Polystick MTS and $aly5tick M37,S, bus maybe used in asphaltic shingles, wood shakes and shingles, non-structural metal roofing, roof the systems and quatq • • ...... .... slate roof assemblies. .. .. .. . ...... Polystick TU P may be used in all the previous assemblies listed except metal roof".... • Polystick IR-Xe may be used in all the previous assemblies listed except metal roofing and roof tile-systemw...;. Polystick TU Max may be used in non-structural metal roofing and roof file systenis..'. • Elastoflex S6 G may be used in roof tile systems only. 0000 IF 00. . .. 3. Deck requirements shall be in compliance with applicable building code. 4. Polystick IR-Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU Plus, Polystick MTS and Polystick MTS Plus shall be applied to a smooth, clean and dry surface. The deck shall be free of irregularities. 5. Polystick IR-Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU Plus, Polystick MTS and Polystick MTS Plus shall not be adhered directly over a pre-existing roof membrane as a recover system. 6. Polystick IR-Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU Plus, Polystick MTS and Polystick MTS Plus shall not be left exposed as a temporary roof for longer than the amount of days listed in the table below after application. Polyglass reserves the right to revise or alter product exposure times; not to exceed the preceeding maximum time limitations. Ex osure Limitations (Days) MTS IR-Xe Elastoflex S6 G TU Plus TU P Tile Pro Dual Pro TU Max MTS Plus Winter Haven, FL 180 90 180 180 180 180 180 180 180 Hazelton, PA N/A 90 N/A 180 N/A N/A N/A 180 N/A rye Coin NOA No.: 15-0410.04 � Expiration Date: 09/13/21 LumpjApproval Date: 08/11/16 Page 5 of 8 7. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61 G20-3 of the Florida Administrative Code. 8. In roof tile application, data for the attachment resistance of roof tiles shall be as set forth in the roof tile manufacturer's Notice of Acceptance. Polystick Tile Pro, Polystick TU Max, Polystick TU Plus or Elastoflex S6 G may be used in both adhesive set and mechanically fastened roof tile applications. Polystick Dual Pro is limited to mechanically fastened roof tile applications. Polystick MTS and Polystick MTS Plus are limited to mechanically fastened with the limitations outlined in Section 9. Polystick TU P may be used in mechanically fastened roof tile applications with the exception of mortar set tile applications. 9. When loading roof tiles on roof tile underlayment for (direct -to -deck) tile assemblies, the maximum roof slope shall be as follows: (See Table Below) 10. Tile Profile Polystick MTS Elastoflex Polystick TU Plus, TU P, Polystick Polystick S6 G Tile Pro, Dual Pro TU Max MTS Plus Flat Tile Prohibited 4:12 6:12 6:12 5:12 without battens Profiled Tile Prohibited 4:12 6:12 6:12 4:12 without battens The above slope limitations can be exceeded only by using battens in accordance with the Approv ed.Tile System Notice of Acceptance and applicable Florida Building Code requirements. When bajten§-qe requrreclt they shall... • . . . . . . be utilized during loading and installation of tiles. .� • • Care should be taken during the loading procedure to keep foot traffic to a minimurrrandto avoid dropping of tile directly on the underlayment. Refer to Polyglass' Tile loading detail below for lg3ditprocggCe -, two tire's' •: laid perpendicular to slope followed by a maximum four tile stack parallel to the slope,• Mr a totJI of 6 tiles -•fqr • all underlayments except Polystick MTS which shall be loaded onto battens. so • • • • . 00000 d I Q. O N tarot Deck prepared vdtn. POLYSnCKTU Plus .... NOA No.: 15-0410.04 Expiration Date: 09/13/21 Approval Date: 08/11/16 Page 6 of 8 11. Refer to prepared roofing system Product Control Notice of Acceptance for listed approval of this product with specific prepared roofing products. Polystick IR-Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU Plus, Polystick MTS, Polystick MTS Plus or Elastoflex S6 G may be used with any approved roof covering Notice of Acceptance listing Polystick IR-Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU Plus, Polystick MTS, Polystick MTS Plus or Elastoflex S6 G as a component part of an assembly in the Notice of Acceptance. If Polystick IR-Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU Plus, Polystick MTS, Polystick MTS Plus or Elastoflex S6 G are not listed, a request may be made to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control Section for approval provided that appropriate documentation is provided to detail compatibility of the products, wind uplift resistance, and fire testing results. POLYGLASS GENERAL APPLICATION GUIDELINES FOR POLYSTICK MEMBRANES PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC APPLICATIONS. LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS. 1. Polyglass does accept the direct application of Polystick underlayment membranes to wood decks. Installers are cautioned to refer to applicable local building codes prior to direct deck installation to ensure this is acceptable. Please also refer to applicable Product Data Sheets of the corresponding products. -*see 2. All rolls, with the exception of Polystick TU Plus should be back -nailed in selvage edge -seam as 13df Polyglasg • • ; • Back Nailing Guide. Nails shall be, 11 gauge ring shank type, applied with a mining �hs�8" met4*l disk as required in Miami -Dade County or simplex type nail as otherwise allowable in other+�fficans, at a minimum date • of 12" o.c. Polystick TU Plus should be back nailed in designated area marked "nail area, area par �alavar" OA•' •; 00 the face of membrane, with the above stated nails and/or disks. The head lap membrahVis to cover the area being. .. ... back -nailed. (Please refer to applicable local building codes prior to installation.) .... 0.090 .. ... . ...... 3. All seal lap seams (selvage laps) must be rolled with a hand roller to ensure full cor4;ei •; • 4. All fabric over fabric; and granule over granule end laps, shall have a 6" wide, uniform layer ofrulyglass Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium AD 1711shing."ment, ; • • • •; XtraFlex 50 Premium Modified Wet/Dry Cement, Polyglass PG500 MB Flashing Cement, applied in between the application of the lap. The use of mastic between the laps does not apply to Polystick MTS. 5. A maximum of 6 tiles per stack are allowed when loading tile on the underlayments. Refer to the Polyglass Tile Loading Guidelines. See General Limitations #9 and #10. 6. Battens and/or Counter -battens, as required by the the manufacturers NOA, must be used on all projects for pitch/slopes of 7/12" or greater. It is suggested that on pitch/slopes in excess of 6'/4"/12", precautions should be taken, such as the use of battens to prevent tile sliding during the loading process. 7. Minimum cure time after membrane installation & before loading of roofing tiles is Forty -Eight (48) Hours. S. Polystick membranes may not be used in any exposed application such as crickets, exposed valleys, or exposed roof to wall details. 9. Repair of Polystick membranes is to be accomplished by applying Polyglass Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, XtraFlex 50 Premium Modified Wet/Dry Cement, Polyglass PG500 MB Flashing Cement to the area in need of repair, followed by a patch of the Polystick material of like kind should be set and hand rolled in place over the area needing such repair. Patching membrane shall be a minimum of 6 inches in either direction. The repair should be installed in such a way so that water will run parallel to or over the top of all laps of the patch. NOA No.: 15-0410.04 Expiration Date: 09/13/21 Approval Date: 08/11/16 Page 7 of 8 10. All self -adhered membranes must be rolled to ensure full contact with approved substrates. Polyglass requires a minimum of 40 lbs for a weighted roller for the rolling of the field membrane. Hand rollers are acceptable for rolling of patches or small areas of the roof. Brooming may be used where slope prohibits rolling. 11. All approved substrates should be dry, clean and properly prepared, before any application of Polystick membranes commences. An approved substrate technical bulletin can be furnished upon request. It is recommended to refer to applicable building codes prior to installation to verify acceptable substrates. 12. The Polyglass Miami -Dade Notice of Acceptance (NOA) approval for Polystick membranes can be furnished upon request by our Technical Services Department by calling 1 (800) 894-4563. 13. Questions in regards to the application of Polyglass products should be directed to our Technical Services Department at 1 (800) 894-4563. 14. Polyglass recommends that applicators follow good roofing practices and applicable procedures as outlined by the National Roofing Contractors Association (NRCA). PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC APPLICATIONS. LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS. END OF THIS ACCEPTANCE • •••• • ••••• •• •• •• • •••••• •••••• • • • • • • • • • • • • • • • *90 • NOA No.: 15-0410.04 Expiration Date: 09/13/21 Approval Date: 08/11/16 Page 8 of 8 MIAMI-DARE COUNTY MIAMFDA EE PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.sov/economy Crown Building Products of Florida, LLC 6018 HAW 72 Arcadia, FL 34266 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. ••.. This product is approved as described herein, and has been designed to comply with* t4e Florida JVul1ding Me: including the High Velocity Hurricane Zone of the Florida Building Code. ...... • , , .... ...... DESCRIPTION: Tuscany Roof Tile • • • • • . • , LABELING: Each unit shall bear a permanent label with the manufacturer's name or logoCity, state-464 folloixlg.. statement: "Miami -Dade County Product Control Approved", unless otherwise noted herem.. • RENEWAL of this NOA shall be considered after a renewal application has been filed'lad'thtre h4oeetj no A in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA consists of pages I through 7. The submitted documentation was reviewed by Juan E. Collao, R.A. NOA No.: 14-1006.02 Expiration Date: 01/29/20 Approval Date: 01/29/15 Page 1 of 7 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub -Category: Roofing Tiles Material: Concrete 1. SCOPE This approves a roofing system using Tuscany Roof Tile, as manufactured by Crown Building Products of Florida, LLC as described in Section 2 of this Notice of Acceptance. For locations where the pressure requirements, as determined by applicable Building Code does not exceed the design pressure values obtained by calculations in compliance with RAS 127 using the values listed in section 4 herein. The attachment calculations shall be done as a moment based system. 2. PRODUCT DESCRIPTION Manufactured by Dimensions Test Applicant Specifications Tuscany Roof Tile L = 17" TAS 112 W = 13" H = 2.3" Thickness: 0.5" Trim Pieces L = varies TAS 112 W = varies Varying thickness 2.1 PRODUCTS MANUFACTURED BY OTHERS Product Name Product Description Product Description Low profile, interlocking, concrete tile equipped with two nail holes. For direct deck'o}'hattened . . ........ nail -on, mortar or adhe�s•iveset applic..ations. • • ...... .. . ...... Accessory trim, concrete roof pieces To:use ai....: ..6 hips, rakes, ridges and. ,alley terrnkMions. ..... Manufactured for each file }profile..... .. ; , . • . . 000000 .. . ...... 3MTm 2- Component Foam Roof Tile Two component polyurethane Adhesive AH-160 foam adhesive. TILE BONDTM Roof Tile Adhesive "Tile Tite" Roof Tile Mortar Bonsal Roof Tile Mortar "QuArete" Roof Tile Mortar, FL-15 Single component polyurethane foam roof tile adhesive. Premixed, pre -bagged roof tile mortar. Premixed, pre -bagged roof tile mortar. Premixed, pre -bagged gray roof tile mortar. 2.2 MANUFACTURING LOCATION 1. Arcadia, FL . . . . ...... Maut acturer • 0Mth'Cu0rrent140A1 :0600• 3M Company The Dow Chemical Company Bermuda Roof Co. Inc. Bonsal American The Quikrete Companies, Inc. NOA No.: 14-1006.02 Expiration Date: 01 /29/20 Approval Date: 01/29/15 Page 2 of 7 2.3 SUBMITTED EVIDENCE: Test Aeency Test Identifier Redland Technologies 7161-03 Appendix III 7161-03 Appendix II Letter P0631-01 P0402 The Center for Applied. Engineering, Inc. Celotex Corporation Testing Service Walker Engineering, Inc. American Test Lab of South Florida 94-083 94-084 25-7094-(1, 4, & 7) 25-7183-(1, 2 & 7) 25-7214-(2 & 6) 25-7487-1 25-7496-(2 & 3) 25-7804-5 528454-2-1 520109-2 Calculations Evaluation Calculations Evaluation Calculations Evaluation Calculations Evaluation Calculations Evaluation Calculations Evaluation Calculations Evaluation Calculations Evaluation Calculations Evaluation Calculations RT0908.02-14 RT0912.02-14 Test Name/Renort Date PA 102 & PA 102(A) Dec. 1991 PA 108 (Nail -On) Dec. 1991 PA 108 (Nail -On) Aug. 1994 PA 108 (Mortar Set) July 1994 Withdrawal Resistance Testing of screw Sept. 1993 vs. smooth shank nails PA 101 (Adhesive Set) April 1994 PA 101 (Mortar Set) May 1994 PA 102 Oct. 1994 PA 102 Feb. 1995 PA 102 March, 1995 PA 102 Dec. 1995 PA 102 Dec. 1995 PA 102 ••••Sgp.1996 . . .... ...... PA 101 •••••• ••�•�ep.1998•�;• PA 101 .. • ; . • •Dec. 1998 • Aerodynamic Multiplier • • • • : • • IVlarch 1991--. 25-7183 • • : • • ; . • • March 1995 • • 25-7094 • • • • • • • Ve bi uary 10 • 25-7496 ; ; Qpril 199,E • ; • 25-7584 : *WUmber.1996 . 25-7804b-8 • • • • • q�lgcjmber-7994 : 25-7804-4 & 5 DeHmber 1996 25-7848-6 December 1996 Aerodynamic Multipliers April 1999 Two Patty Adhesive Set System April 1999 TAS 112 09/18/14 Restoring Moments 09/18/14 Aerodynamic Multiplier MIAMFQADADE COUNTY Expiration No.: 14-1006.02 Expiration Date: 01/29/20 Approval Date: 01/29/15 Page 3 of 7 3. LIMITATIONS 3.1 Fire classification is not part of this acceptance. 3.2 For mortar or adhesive set tile applications, a static field uplift test shall be performed in accordance with TAS 106. 3.3 Applicant shall retain the services of a Miami -Dade County Certified Laboratory to perform quarterly test in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Miami -Dade Product Control office for review. 3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed section 4.1 herein. 3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated otherwise by the underlayment material manufacturers published literature. 3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with applicable building code. 3.7 All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61 G20-3 of the Florida Administrative Code. 4. INSTALLATION 4.1 Tuscany Roof Tile and its components shall be installed in strict compliance with Roof n,% Application Standard RAS 118, RAS 119, and RAS 120. • • • • • • • • • • • • 4.2 Data For Attachment Calculations : . ...' .: Table 1: Average Weight (W) and Dimensions (I x v/ ...... Tile Profile Weight-W (lbf) Length-1 (ft) " ' Wi th-w (ft} •; • • • Tuscany Roof Tile 10.0 1.42 ..' .' •001.Q8 ...... Table 2: Aerodynamic Multipliers - A (ft) Tile Profile A (ft) • • A•(ft) • • • • • Batten Application Direct Deck Application Fuscany Roof Tile 0.289 0.313 Table 3: Restoring Moments due to Gravity - M9 (ft-lbf) Tile Profile 2":12" 3":12" 4":12" 511:12" 611:12" 7":12" or greater Tuscany Roof Tile Battens Direct Deck Battens Direct Deck Battens Direct Deck Battens Direct Deck Battens Direct Deck Battens Direct Deck 7.06 7.06 6.99 6.99 6.88 6.88 6.73 6.74 6.57 6.57 6.38 6.39 MCOUNOA No.: 14-1006.02 Mi a�►ueExpiration Date: 01/29/20 Approval Date: 01/29/15 Page 4 of 7 Table 4: Attachment Resistance Expressed as a Moment - Mf (ft-lbf) for Mechanically Attached Systems Tile Fastener Type Direct Deck Direct Deck Battens Profile (min 15/32" (min. 19132" plywood) plywood) Tuscany Roof Tile 2-10d Ring Shank Nails 27.8 37.4 28.8 1-10d Smooth or Screw Shank 8.8 11.8 4.1 Nail 2-10d Smooth or Screw Shank 16.4 21.9 7.1 Nails 1 #8 Screw 25.8 25.8 22.9 2 #8 Screw 47.1 47.1 49.1 1-10d Smooth or Screw Shank 24.3 24.3 24.2 Nail (Field Clip) 1-10d Smooth or Screw Shank 19.0 19.0 22.1 Nail (Eave Clip) . • • • •. 2-10d Smooth or Screw Shank 35.5 .•3515 ... 34.8 .' Nails (Field Clip) ...... .. . ...... 2-10d Smooth or Screw Shank 31.9 . al.9 32.j• • • •; Nails (Eave Clip) . •... ...... ..... 2-10d Ring Shank Nails 43.0 " 87.5 " ' 50.900.;. ...... . . 1 Installation with a 4" the headlap and fasteners are located a min. of 2'/" from head of tile. ; •.... 0 0 Table 5: Attachment Resistance Expressed as a Moment Mf (ft4bf) 00 for Two Patty Adhesive Set Systems Tile Profile Tile Application Minimum Attachment Resistance Tuscany Roof Tile Adhesive 26.13 2 See manufacturer's component approval for installation requirements. 3 TILE BOND Roof Tile Adhesive; Average weight per patty 11.4 grams. 3MTm 2-Component Foam Roof Tile Adhesive AH-160; Average weight per patty 8 grams. NOA No.: 14-1006.02 Expiration Date: O1/29/20 Approval Date: 01/29/15 Page 5 of 7 Table 6: Attachment Resistance Expressed as a Moment - Mf (ft-lbf) for Single Patty Adhesive Set Systems Tile Profile Tile Application Minimum Attachment Resistance Tuscany Roof Tile 3M 2-Component Foam Roof Tile Adhesive AH-160 86.61 Wm 2-Component Foam Roof Tile Adhesive AH-160 45.5 4 Large paddy placement of 54 grams of 3MTm 2-Component Foam Roof Tile Adhesive AH-160. 5 Medium paddy placement of 24 grams of 3M 2-Component Foam Roof Tile Adhesive AH-160. Table 7: Attachment Resistance Expressed as a Moment - Mt (ft-lbf) for Mortar Set Systems Tile Profile Tile Application Attachment Resistance Tuscany Roof Tile Mortar Setb 20.6 6 Seespecific mortar manufacturer's Notice of Acceptance .... . . 5. LABELING " • • All tiles shall bear the imprint or identifiable marking of the manufacturer's name 0 r•1tf&d jSee Dptail•Belo",* ti• following statement: "Miami -Dade County Product Control Approved". " . . ...... .... . ..... .... .... ..... Q. .. .. . ...... .. . . . . . ...... . . ...... .. . ... 0 n .. V TUSCANY ROOF TILE (LOCATED ON UNDERSIDE OF TILE) 6. BUILDING PERMIT REQUIREMENTS: 6.1 Application for building permit shall be accompanied by copies of the following: 6.1.1 This Notice of Acceptance. 6.1.2 Any other documents required by Building Official or Applicable building code in order to properly evaluate the installation of this system. NOA No.: 14-1006.02 Expiration Date: 01/29/20 Approval Date: 01/29/15 Page 6 of 7 4 PROFILE DRAWINGS FASTENER HOLE TuscANY ROOF TILE END OF THIS ACCEPTANCE NOA No.: 14-1006.02 Expiration Date: 01/29/20 Approval Date: 01/29/15 Page 7 of 7