Loading...
RF-17-2243Project Address Miami Shores Village 10050 N.E. 2nd Avenue NE Miami Shores, FL 33138-0000 Phone: (305)795-2204 Permit Issue Date: 9120/2017 Permit NO. RF -9-17-2243 Permit Type: Roof Work Classification: Flat Permit Status: APPROVED Expiration: 03/19/2018 Parcel Number Applicant 9342 NE 9 Avenue Miami Shores, FL 1132060020050 Block: Lot: FRANCES PEAKE Owner Information Address Phone Cell FRANCES PEAKE 9342 NE 9 AVE MIAMI SHORES FL 33138-2904 Contractor(s) Phone CeII Phone ISAACS ROOFING & INSULATION COI (305)234-5234 (786)277-9756 Type of Work: Re Roof Additional Info: RE -ROOF FLAT TO FLAT Classification: Residential Scanning: 3 Fees Due Bond Type - Contractors Bond CCF DBPR Fee DCA Fee Education Surcharge Permit Fee - New Roof Scanning Fee Technology Fee Total: Amount $500.00 $4.20 $3.75 $3.75 $1.40 $250.00 $9.00 $5.60 $777.70 Pay Date Invoice # 09/20/2017 09/19/2017 Bond #: 3511 Pay Type RF -9-17-65091 Credit Card Credit Card Amt Paid Amt Due $ 727.70 $ 50.00 $ 50.00 $ 0.00 Available Inspections: Inspection Type: Tin Cap Final Roof Roof in Progress Renailing Affidavit Review Roof In consideration of the issuance to me of this permit, I agree to perform the work covered hereunder in compliance with all ordinances and regulations pertaining thereto and in strict conformity with the plans, drawings, statements or specifications submitted to the proper authorities of Miami Shores Village. In accepting this permit I assume responsibility for all work done by either myself, my agent, servants, or employes. I understand that separate permits are required for ELECTRICAL, PLUMBING, MEC ANICAL, WINDOWS, DOORS, ROOFING and SWIMMING POOL work. OWNERS AFFIDAVIT- - at the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and z• mg. Futherm.r- I authorize the above-named contractor to do the work stated. Authorized igna ur er / Applicant / Contractor / Agent Building Department Copy September 20, 2017 Date September 20, 2017 1 BUILDING PERMIT APPLICATION Miami Shores Village Building Department 10050 N.E.2nd Avenue, Miami Shores, Florida 33138 Tel: (305) 795-2204 Fax: (305) 756-8972 INSPECTION LINE PHONE NUMBER: (305) 762-4949 Master Permit No. RECEIVED SEP 19 2017 FBC 2014 11- 7243 Sub Permit No. El BUILDING ❑ ELECTRIC ROOFING ElREVISION ElEXTENSION ❑RENEWAL ❑PLUMBING ❑ MECHANICAL ❑PUBLIC WORKS ❑ CHANGE OF ❑ CANCELLATION ❑ SHOP CONTRACTOR DRAWINGS JOB ADDRESS: 3l -i2_. ': g -t H i0416 City: Miami Shores County: Folio/Parcel#: I_ 3'2-0 - 002,- ©0 5 7 Miami Dade Zip: Is the Building Historically Designated: Yes NO 1Y Occupancy Type: Load: Construction Type: Flood Zone: BFE: FFE: OWNER: Name (Fee Simple Titleholder) 'v Y"� te- Phone#: 0S 31 Address: CI '34 L1�E ° l if / V" �+ City: Mt AM 1 , by 7 State: - Zip: 913 Tenant/Lessee Name: Email: '�r'o.Vl Ct i ro-Ate 3wlei..11. Goy„ CONTRACTOR: Company Name:i4C Jam}- Phone#: 3( 23 V ,S L3 NJ Phone#. Address: City: ®Gve144 Qualifier Name: 414* lOv (9.1-7 6 S', t t'Y'''( (4 -by State: 4 c_ Phone#: Zip: 3 7/fa 1416 2 State Certification or Registration #: C e C S JSA Certificate of Competency #: DESIGNER: Architect/Engineer: Phone#: Address: City: State: Zip: Value of Work for this Permit: $ (OCI g® Square/Linear Footage of Work: Type of Work: ❑ Addition ❑ AlterationA ❑ New ��g,� Description of Work: rl7 � 11-,� `� -"" k Goo Repair/Replace ❑ Demolition Specify color of color thru tile: Submittal Fee $ 50 • Cl Permit Fee $%' l CCF $ CO/CC $ Scanning Fee $ $ Radon Fee $ DBPR $ Notary $ Technology Fee $ Training/Education Fee $ Double Fee $ Structural Reviews $ Bond $ 5-106 ' 6V TOTAL FEE NOW DUE $ 22-- • .4C) (Revised02/24/2014) • , ,t? • ,+ A qor ; t ; • 1•1 jr,441, •-; • Bonding Company's Name (if applicable) Bonding Company's Address City State Zip Mortgage Lender's Name (if applicable) Mortgage Lender's Address City State Zip Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRIC, PLUMBING, SIGNS, POOLS, FURNACES, BOILERS, HEATERS, TANKS, AIR CONDITIONERS, ETC OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. "WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT." Notice to Applicant: As a condition to the issuance of a building permit with an estimated value exceeding $2500, the applicant must promise in good faith that a copy of the notice of commencement and construction lien low brochure will be delivered to the person whose property is subject to attachment. Also, a certified copy of the recorded notice of commencement must be posted at the job site for the first inspection which occurs seven (7) days after the building permit is issued. In the absence of such posted notice, the inspection will not be approved and a reinspection fee will be charged. (Signature ()tiire-tk OWNER or AGENT The f going instr nt as ac nowledged before me this dayot m✓ 20 1 " 1 by r fetrez is personally kno to Signature CONTRACTOR ing instru as acknowledged before me this "e- 20 IT to me or who has produced as me or who has produced as identification and who did take an oath. NOTARY PUBLIC: Print: Seal: Commission +M GG 027219 dri My Comm. Expires Sep 6, 2020 JO' Bonded through National Notary Asse. APPROVED BY (Revised02/24/2014) identification and who did take an oath. NOTARY PUB :'a� Pr S Plans Examiner Commission +9 SG 027219 1„'N rc' My Comm. Expires Sep 6, 2020 I "''` Bonded through National Notary Msn, Zoning Structural Review Clerk • Miami Shores Village Building Department 10050 N.E.2nd Avenue Miami Shores, Florida 33138 Tel: (305) 795.2204 Fax: (305) 756.8972 OWNERS'S AFFIDAVIT OF EXEMPTION ROOF TO WALL CONNECTION HURRICANE MITIGATION RETROFIT FOR EXISTING SITE - BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES PERSUANT TO SECTION 553.844 F.S. To: Miami Shores Village Building Department 10050 NE 2nd Ave Miami Shores, FI 33138 Re: Owners Name: Date: --13T' 1 Z.oj.� P�K� Property Address: 34 2- 1\1 '9 rt fi Avg Roofing Permit Number. Dear Building Official: AA 1 t-r(‘an C 15 p-{ oUK certify that I am not required to retrofit the roof to wall connections of my building because: )The just valuation for the structure for purpose of ad valorem taxation is less than $300,000.00. Please attach proof of ad valorem taxation. o The building was constructed in compliance with the provisions of the Florida Building Code (FBC) or with the provisions of 1994 edition of the South Florida Building Code (1994 SFBC) 1-r-117) 6Slgna re \-(J4 r -s M rt1V-fr FrirlfName State of Florida County of Dade The undersigned, being the first duly swom, de es and says that h Swom to and subscribed before me this da of Notary Public, Sate of Florida at e is the o er for the above • roperty mentioned. 1111' ' �� N— IDAL,L CASTELLANOS r `'V : Notary Public State of Florida Commission # GG 027219 A; My Comm. Expires Sep 6, 2020 .M.Bonded through National NotiryMil • When the just valuation of the structure for purpose of ad valorem taxation is equal to or more than $300,000.00, and the budding was not constructed with FBC nor a 1994 SFBC. Then you must provide a building application from a General Contractor for the Roof to Wal connection Hurricane Mitigation. Revised on 5/21/2009 Paid By CORELOGIC TAX SERVICE Miami -Dade County, Florida Paid 11/23/2016 plicate public_user 04/11/2017 Receipt # EEX-17-000360 $3,177.44 2016 Real Estate Property Taxes Notice of Ad Valorem Tax and Non -Ad Valorem Assessments SEE REVERSE SIDE FOR IMPORTANT INFORMATION FOLIO NUMBER MUNICIPALITY 11-3206-002-0050 FRANCES M PEAKE 9342 NE 9 AVE MIAMI SHORES, FL 33138 MIAMI SHORES Property Address 9342 NE 9 AVE Miami -Dade School Board School Board Operating School Board Debt Service State and Other Florida Inland Navigation Dist South Florida Water Mgmt Dist Okeechobee Basin Everglades Construction Proj Childrens Trust Authority Miami -Dade County County Wide Operating County Wide Debt Service Fire Rescue Operating Fire Rescue Debt Service Municipal Goveming Board Miami Shores Operating Miami Shores Debt Service 0' T AD VALOREM TAXES MILL CODE 1100 Exemptions: ADDL. HOMESTEAD, HOMESTEAD 148,661 7.13800 148,661 0.18400 148,661 0.03200 148,661 0.13590 148,661 0.14770 148,661 0.04710 148,661 0.50000 148,661 4.66690 148,661 0.40000 148,661 2.42070 148,661 0.00750 148,661 7.90000 148,661 0.50540 NON -AD VALOREM ASSESSMENTS ZIG 123,661 123,661 98,661 98,661 98,661 98,661 98,661 98,661 98,661 98,661 98,661 98,661 98,661 FO • AGE/UNI 882.69 22.75 3.16 13.41 14.57 4.65 49.33 460.44 39.46 238.83 0.74 779.42 49.86 F0823 MIAMI SHORES STORMWATER F0824 MIAMI SHORES SANITATION 45.0000 @ 705.5200 Save Time. Pay Online. www.miamidade.gov t RETAIN FOR YOUR RECORDS t 1.000 1.000 Combined taxes and assessments 45.00 705.52 $3,309.83, 2016 Real Estate Property a DETACH HERE AND RETURN THIS PORTION WITH YOUR PAYMENT 1 Du.licate .ublic user 04/11/2017 Taxes FOLK) NUMBER 11-3208-002-0050 PROPERTY ADDRESS 9342 NE 9 AVE LEGAL DESCRIPTION PL OF 1ST ADD TO MARILYN HGTS PB 41-80 LOT 5 LOT SIZE 75.000 X 122 OR 15851-2798 0992 1 FRANCES M PEAKE 9342 NE 9 AVE MIAMI SHORES, FL 33138 111111 UNflHIPMlli1II!1VIE]flhI �Ill1IflN 1+ 1 1 3 2 0 6 0 0 2 0 0 5 0+ 2 0 1 6+ Make checks payable to: Miami -Dade Tax Collector (in U.S. funds drawn on U.S. banks) Amount due May be Subject to Change Without Notice Mail payments to: 200 NW 2nd Avenue, Miami, FL 33128 PAY ONLY ONE AMOUNT If Paid By Please Pay Nov 30, 2016 $0.00 l_I (-)1 ciu J� 1000000000000000001132060020050201600000000000000000000000 Property Search Application - Miami -Dade County OFFICE F T PROPERT APP A SER .dry Page 1 of 1 Summary Report Property Information Folio: 11-3206-002-0050 Property Address: 9342 NE 9 AVE Miami Shores, FL 33138-2904 Owner FRANCES M PEAKE Mailing Address 9342 NE 9 AVE MIAMI SHORES, FL 33138 USA PA Primary Zone 1100 SGL FAMILY - 2301-2500 SQ Primary Land Use 0101 RESIDENTIAL - SINGLE FAMILY : 1 UNIT Beds / Baths / Half 2 / 1 / 0 Floors 1 Living Units 1 Actual Area Sq.Ft Living Area Sq.Ft Adjusted Area 1,995 Sq.Ft Lot Size 9,150 Sq.Ft Year Built 1939 Assessment Information Year 2017 2016 2015 Land Value $247,029 $255,878 $278,737 Building Value $141,141 $141,411 $141,679 XF Value $710 $716 $631 Market Value $388,880 $398,005 $421,047 Assessed Value $151,782 $148,661 $147,628 Benefits Information Benefit Type 2017 2016 2015 Save Our Homes Cap Assessment Reduction $237,098 $249,344 $273,419 Homestead Exemption $25,000 $25,000 $25,000 Second Homestead Exemption $25,000 $25,000 $25,000 Note: Not all benefits are applicable to all Taxable Values (i.e. County, School Board, City, Regional). Short Legal Description PL OF 1ST ADD TO MARILYN HGTS PB 41-60 LOT 5 LOT SIZE 75.000 X 122 OR 15651-2798 0992 1 Generated On : 9/19/2017 Taxable Value Information 2017 20163 2015 County Exemption Value1 $50,000 $50,000 $50,000 Taxable Value $101,782 $98,661 $97,628 School Board Exemption Value $25,000 $25,000 $25,000 Taxable Value $126,782 $123,661 $122,628 City Exemption Value $50,000 $50,000 $50,000 Taxable Value $101,782 $98,661 $97,628 Regional Exemption Value $50,000 $50,000 $50,000 Taxable Value $101,782 $98,661 $97,628 Sales Information Previous Sale Price OR Book -Page Qualification Description 09/02/2015 $200,000 29763-4616 Affiliated parties 09/01/1992 $94,500 15651-2798 Sales which are qualified The Office of the Property Appraiser is continually editing and updating the tax roll. This website may not reflect the most current information on record. The Property Appraiser and Miami -Dade County assumes no liability, see full disclaimer and User Agreement at http://www.miamidade.gov/info/disclaimer.asp Version: http://www.miamidade.gov/propertysearch/ 9/19/2017 Florida Building Code Edition 2010 High Velocity Hurricane Zone Uniform Permit Application Form Section A (General Information) Master Permit No. Process No. = 1 1 ekCS 1046 9 3 - N.� Contractor's Name Job Address Low Slope ❑ Asphaltic Shingles 0 New Roof ROOF CATEGORY ❑ Mechanically Fastened Tile ❑ Metal Panel/Shingles r ❑ Mortar/Adhesi=bet Tile, ❑ Wood Shingles/Sliaks ❑ Prescriptive BUR -RAS 150 ROOF TYPE 1;14Reroofing 0 Recovering 0 Repair ROOF SYSTEM INFORMATION Low Slope Roof Area (SF) Steep Sloped Roof Area (SF) SECTION B (Roof Plan) Sketch Roof Plan: Illustrate all levels and sections, roof drains, scd13PeYh, overflbw scuppers and overflow drains. Include dimensions of sections and IeKels, c�etarly identify dimensions of elevated pressure zones and location of palagrefls. • • • • 0 Maintenance • • • • ••• • TotalfSfi• 6.6244 .•.. • • • .. • . •• �• . . •• ... • . •.. •• •• .... i r r i�. i1 J t • • •• • • 7✓ V L Olt i( TE SUBJECT TO COMPLIANCE WI i H ALL FEDERAL STATE AND CC_"JTY RULES AND REGJLATIO'IS • Florida Building Code Edition 2010 High Velocity Hurricane Zone Uniform Permit Application Form Section C (Low Sloped Roof System) Fill in Specific Roof Assembly Components and Identify Manufacturer (If a component is nod identify as "NA") System Manufacturer: ./1,7^: )/ 4.1) r3 dz /77 d/ NOA No.: Design Wind Pressures, From RAS 128 or Calculations: f 4s 0 Pmax1: /.2 Pmax2: 1/ Pmax3: /£`%!l • Max. Design Pressure, From the Specific NOA System: =- • 4 Deck: Type: Gauge/Thickness: Slope: Anchor/Base Sheet & No. of Ply(s): `%9 Anchor/Base Sheet Fastener/Bonding Material/ r 41 insulation Base Layer: t� },i_ 'v4rV,A"'er/%ij Base Insulation Size and Thickness: 1ti 'a G.1/ 7 Base Insulation Fastener/Bonding Material: A//4 Top Insulation Layer: Top Insulation Size and Thickness: A Top Insulation Fastener/Bonding Material:t 4 °j ej 4 Base'oheet(s) & No. of Ply(sj: Base Sheet Fastene.r�Bond' g Material: Ply Sheet(s) & No. of Ply(s): / /4 Ply Sheet Fasten rlBonding M lariat: Top PIy: E .57.i!' '' it' . <';:lit� ',47/"; Top Top Ply Fastener/Bo/ding Materi Surfacino: Fastener Spacing for Anchor/Base Sheet Attachment Field: �'°" oc @ Lap, # Rows " @ /26" oc t rfi " oc @Lap, #Rows � @ ^ " oc "oc @ Lap, # Rows @ P• ^ oc of Fasteners Per Insulation j i If Peri mee' Corner Perimeter: Corner: Number Board Field: Illustrate Components Noted and Details as Applicable: Woodblocking, Gutter, Edge Termination, Stripping, Flashing, Continuous Cleat, Cant Strip, Base Flashing, Counter- Flashing,...• Coping, Etc. • • • • •••. Indicate: Mean Roof Height, ira et• Height, Height of Base Flashing, Component tiaterial, . • �. Material Thickness, Fastener "WV' astener•• • • Spacing or Submit Manufactureps•Oenails that Comply with RAS 111 and Chapter 16. • • • . • • • • a.•• • L 54 y3 ; „4/y` • • . • •1 / • • • • •• • • • •••• • • • Parapet • •. etiat Y A d—'T Mean Roof Height ••• • • • •• MIAMI. DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) BOARD AND CODE ADMINISTRATION DIVISION NOTICE OF ACCEPTANCE (NOA) Polyglass USA, Inc. 150 Lyon Drive Fernley, NV 89408 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 www.miamidade._ov/economy SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. •.... • DESCRIPTION: Polyglass Self -Adhered Roof System over Wood Decks • • • •• ••• • • ..•• • LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city. vote and f'ollo}ying statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. •.... • . . •. • RENEWAL of this NOA shall be considered after a renewal application has been filed and there ltas been Ifo Change • in the applicable building code negatively affecting the performance of this product. . • . • • TERMINATION of this NOA will occur after the expiration date or if there has been a revilip• pbr• hang� lii the. • materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County; Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA# 13-0514.10 and consists of pages 1 through 33. The submitted documentation was reviewed by Alex Tigera. MIAMI•DADE COUNTY APPROVED NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 1 of 33 • ROOFING ASSEMBLY APPROVAL Category: Sub -Category: Materials Deck Type: Maximum Design Pressure Roofing Modified Bitumen SBS/APP/TPO Wood -112.5 psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Product Dimensions Specification Description Elastobase XtraFlex SBS Glass Base Polyglass G2 Base Polyanchor Elastobase P Elastoflex SA V FR (1.5 -mm) Elastoflex SA V PLUS FR 65' 2" x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced Type I base sheet. 65' 8" x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced Type I base sheet. 108' x 36" ASTM D 4601 Asphalt -coated fiberglass reinforced base sheet Type II 250' x 48" ASTM D 4601 A polymer woven, high performance, synthetic base Type II sheet. 65' 8" x 3' 3-3/8" ASTM D 6164, SBS modified asphalt coated polyester retie fgrFed bash Type I sheet. • • ••• •• 66' 8" x 3' 3-3/8" ASTM D 6163, Self -adhered, fire -rated, fib>SfglaSs•reinforeed,BS Type I modified bitumen membrane fit? a self -adhering bac$ face and a smooth top surface ...• • 66' 8" x 3' 3-3/8" ASTM D 6163, Self -adhered, fire -rated, fiberllass.reinforced,SBS • • Type I modified bitumen membrarierwih a self-adhring back face and a smooth top surf ,: • •• • ASTM D 6163, Self -adhered, fiberglass reiQforesd, SBSrxadified . Type I bitumen membrane with a s2,1adI ering back face ant a smooth top surface.•.; 66' 8" x 3' 33/$" ASTM D 6163, Self -adhered, fiberglass reinforced, SBS modified Type I bitumen membrane with a self -adhering back face and a smooth top surface. ' • Elastoflex SA V (1.5- 66' 8" x 3' 33/$" mm) Elastoflex SA V PLUS XtraFlex SBS Base SA Elastoflex SA P FR XtraFlex SBS G SA MIAMI•DADE COUNTY APPROVED 66' 8" x 3' 3-3/8" ASTM D 6163, Self -adhered, fiberglass reinforced, SBS modified Type I bitumen membrane with a self -adhering back face and a smooth top surface. 32' 10" x 3' 3-3/8" ASTM D 6164, Self -adhered, fire -rated, polyester reinforced, SBS Type I modified bitumen membrane with a self -adhering back face and a granule top surface. 32' 10" x 3' 3-3/8" ASTM D 6164, Self -adhered, fire -rated, polyester reinforced, SBS Type I modified bitumen membrane with a self -adhering back face and a granule top surface. NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 2 of 33 • • • • . Elastoflex SA P Polyflex XtraFlex APP S Polybond Polyflex G Polyflex SA P Polyflex SA P FR XtraFlex APP G SA Polyfresko G SBS SA Polyfresko G SBS SA FR Polyfresko G APP SA Polyfresko G APP SA FR PolyKool 32' 10" x 3' 3-3/8" ASTM D 6164, Type I 32' 10" x 3' 3-3/8" ASTM D 6222 32' 10" x 3' 3-3/8" ASTM D 6222 32' 10" x 3' 3-3/8" ASTM D 6222 32' 10" x 3' 3-3/8" ASTM D 6222 32' 10" x 3' 3-3/8" ASTM D 6222, Type I 32' 10" x 3' 33/$" ASTM D 6222, Type I 32' 10" x 3' 3)/8" ASTM D 6222, Type I 32' 10" x 3' 3-3/8" ASTM D 6164, Type I 32' 10" x 3' 33/$" ASTM D 6164, TypeI 32' 10" x 3' 3-3/8" ASTM D 6222, Type I 32' 10" x 3' 3-3/8" ASTM D 6222, Type I 32' 10" x 3' 3-3/8" XtraFlex Kool APPS 32' 10" x 3' 3-3/8" SA Polyglass APP Base MIAMI•DADE COUNTY APPROVED ASTM D6222 Type 1 ASTM D6222 Type I 65' 8" x 3' 3-3/8" ASTM D 6509 Type I Self -adhered, fiberglass reinforced, SBS modified bitumen membrane with a self -adhering back face and a granule top surface. Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface. Self -adhered, polyester reinforced, APP modified bitumen membrane with a self -adhering back face and a granule top surface. Self -adhered, fire -rated, polyester reinforced, APP modified bitumen membrane with a self -adhering back face and a granule top surface. Self -adhered, fire -rated, polyister l•einforced,..E3P modified bitumen membrane•40 ae1f-acjherjrig back face and a granule top surface+...• •• • • ••.• . Self -adhered, fiberglass reinforced; SBS modified bitumen membrane with a selacih'esing ba'r.14fs�L`e and • a granule top surface. .... . • Self -adhered, fire -rated, fibesglarsbreinforcodAIS modified bitumen membrana withal self -adhering back face and a granule top surface. • Self -adhered, polyester reinfkcier1,3PP fie�i bitumen membrane with a self -adhering back fa and a granule top surface. Self -adhered, fire -rated, polyester reinforced, APP modified bitumen membrane with a self -adhering back face and a granule top surface Self -adhered, polyester reinforced, APP modified bitumen membrane with a self -adhering back face and a white film laminate on the top surface. Self -adhered, polyester. reinforced, APP modified bitumen membrane with a self -adhering back face and a white film laminate on the top surface. APP modified asphalt coated fiberglass reinforced base sheet. NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 3 of 33 . . PG325 Cold Process Adhesive PG100 Asphalt Primer XtraFlex 10 Asphalt Primer PG350 Mod Bit Adhesive PG400 Plastic Roof Cement PG425 Wet/Dry Roof Cement PG450 Flashing Cement PG500 MB Flashing Cement Polyplus 35 Premium Mod Bit Adhesive XtraFlex 35 Premium Mod Bit Adhesive Polyplus 45 Premium Flashing Cement Polyplus 50 Premium MB Flashing Cement XtraFlex 50 Premium Modified Wet/Dry Cement Polyplus 55 Premium Modified Flashing Cement MIAMI•DADE COUNTY APPROVED 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal, tube or 17 oz. spray can 1, 3, 5, 50, 55 gal, tube or 17 oz. spray can 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube 1, 3, 5, 50, 55 gal. or tube ASTM D3019 Type III ASTM D41 ASTM D41 ASTM D3019 Type III ASTM D4586 ASTM D3409 ASTM D4586 ASTM D3409 ASTM D4586 ASTM D4586 ASTM D3019 Type III ASTM D3019 Type III ASTM D4586 ASTM D4586 ASTM D4586 ASTM D4586 A fibered cold process adhesive for use with roll or BUR roofing. A penetrating solution of solvent and a blend of selected asphalts used to promote adhesion. A penetrating solution of solvent and a blend of selected asphalts used to promote adhesion. A fibered rubberized adhesive designed for use with modified bitumen membranes. A thick, fibered, rubberized flashing cement for use in dry or damp conditions. A thick, fibered, rubberized flashing cement for use in dry or damp conditions. A thick, fibered, rubberized flashing cement. A thick, fibered, rubberized flashing cement for use with modified bitumen membranes. A fibered rubberized adhesive designed for use with modified bitumen membranes. A fibered rubberized adhesive designed fQf1 st•yith modified bitumen membranct. . •. •••• .. . . •. A thick, fibered, rubberized 1;10.41aipg cemc'r ;.. • • . A thick, fibered, rubberized Th I ilig cemj.fpepse with modified bitumen membranes.' . . . . . A thick, fibered, rubberized ilidlaiing cemeritrog use with modified bitumen membranes• . . . • A mastic compound for.use n� rotf flashipg • adhesive. • • es NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 4 of 33 .1 . . . . . APPROVED INSULATIONS: Product Name Polytherm-H Polytherm ACFoam-II ACFoam-III High Density Wood Fiberboard DensDeck, DensDeck Prime H -Shield H -Shield CG ENRGY-3, JM ISO 3 Fesco Board Multi -Max FA -3 SECUROCK Gypsum -Fiber Roof Board MIAMI-DADE COUNTY' APPROVED TABLE 2 Product Description Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Wood fiber insulation board Gypsum insulation board Polyisocyanurate foam insulation Polyisocyanurate/perlite composite insulation Polyisocyanurate foam insulation Expanded mineral fiber Polyisocyanurate foam insulation Fiber reinforced coverboard Manufacturer (With Current NOA) Polyglass USA, Inc. Polyglass USA, Inc. Atlas Roofing Corp Atlas Roofing Corp Generic Georgia-Pacific Gypsum LLC Hunter Panels, LLC Hunter Panels, LLC Johns Manville Corp. Johns Manville Corp. Rmax Operating, LLC. United States Gypsum Corporation • • • . • •• • • •. • • ••.• • •. •.•. •••• • • • ••.• • •• .• . • • • • • . . ••• • • . • • •• • . • • • • • • • • • • •.. • • NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 5 of 33 APPROVED FASTENERS: Fastener Number Product Name 1. Dekfast Fasteners 12, 14 & 15 HS 2. Dekfast Galvalume Steel Hex Plate 3. #14 Roofgrip 4. Flat Bottom Metal Plate 5. Trufast 414 HD Fastener 6. Trufast 3" Metal Insulation Plate 7. Polygrip Fasteners #12, #14 & #15 8. Polygrip Hex Plates MIAMI•DADE COUNTY APPROVED TABLE 3 Product Description Insulation fastener for wood, steel and concrete decks Galvalume hex stress plate. Insulation and membrane fastener A2 -SS aluminized steel plate Insulation fastener for steel and wood decks Round Galvalume AZ50 steel plate Insulation fastener for wood, steel and concrete decks Galvalume hex stress plate. Dimensions 2 7/g" x 3 '/" Various 3" square 3.23 round 3" round Various. 27/a"x 3 'A" Manufacturer (With Current NOA) SFS Intec, Inc. SFS Intec, Inc. OMG, Inc. OMG, Inc. Altenloh, Brinck & Co. U.S., Inc. Altenloh, Brinck & Co. U.S., Inc. Polyglass USA, Inc Polyglass USA, Inc • • • • • •• • • • • • • •••• • •• • • • • ••• • • • • • •• • • • • • •• •• • • . • • • • • • • • • • •• • ••• • NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 6 of 33 APPROVED SURFACING: Product Name PG200 Non-Fibered Roof Coating XtraFlex 20 Bituminous Roof Coating PG300 Fibered Roof Coating XtraFlex Bituminous Roof Coating Fibered PG600 Non-Fibered Aluminum Roof Coating PG650 Fibered Aluminum Roof Coating PG700 Elastomeric Roof Coating PG800 Non-Fibered Asphalt Emulsion Roof Coating XtraFlex 80 Emulsion Roof Coating PG850 Fibered Asphalt Emulsion Roof Coating Polyplus 65 Premium Fibered Aluminum Roof Coating XtraFlex 65 Aluminum Roof Coating Fibered Polyplus 60 Premium Non- Fibered Aluminum Roof Coating XtraFlex 60 Aluminum Roof Coating MIAMI•DADE COUNTY APPROVED TABLE 4 Product Description A non fibered asphaltic coating used to add life and rejuvenate existing BUR roofing substrates. A non fibered asphaltic coating used to add life and rejuvenate existing BUR roofing substrates. An asphalt cutback fibered roof coating. May be applied by brush or spray equipment to rejuvenate aged BUR An asphalt cutback fibered roof coating. May be applied by brush or spray equipment to rejuvenate aged BUR Application Rate 11/2-2 gal/sq Specification Manufactur er TAS 140 Polyglass USA, Inc. 11/2-2 gal/sq TAS 140 Polyglass USA, Inc. 11/2-2 gal/sq ASTM D4479 Polyglass USA, Inc. 11/2-2 gal/sq ASTM D4479 Polyglass USA, Inc. Non-fibered aluminum roof coating. ''/2-1 gal/sq Fibered aluminum roof coating. A premium white elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. An asphalt base, un-fibered clay emulsion An asphalt base, un-fibered clay emulsion An asphalt base, fibered clay emulsion Fibered aluminum roof coating. Fibered aluminum roof coating. Non-fibered aluminum roof coating. Non-fibered aluminum roof coating. ASTM D2824 Polyglass Type I USA, Inc. •.•. 1'/2-2 gal/sq ATM.D2824••Poiyglass. iTypeZI1 : •€A, Inc. 1-1'/2 gal/sq A91%6156083 "Itlyglass. • USA, Inc. 3 gal/sq in two coats 3 gal/sq in two coats 3 gal/sq in two coats 11/2-2 gal/sq 11/2-2 gal/sq 1/2-1 gal/sq 1/2-1 gal/sq . •••• • • •.•• • • • • • ••• • AS'fml'D 1227 • • P5lyglass" • • • • • USA, Inc. •• • • ASTM.D1227: Wyglass. • • • • USA, Inc. • ASTM D1227 Polyglass USA, Inc. ASTM D2824 Polyglass Type III USA, Inc. ASTM D2824 Polyglass Type III USA, Inc. ASTM D2824 Polyglass Type I USA, Inc. ASTM D2824 Polyglass Type I USA, Inc. NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 7 of 33 APPROVED SURFACING: Product Name Polybrite 70 Premium Grade Elastomeric Roof Coating XtraFlex 70 Premium Acrylic FR Roof Coating Polybrite 90 High Solids Silicone Roof Coating XtraFlex SRC 9600 High Solids Silicone Roof Coating Polybrite 95 Silicone Roof Coating XtraFlex SRC 8000 Silicone Roof Coating Gravel Slag MIAMI.DADE COUNTY APPROVED TABLE 4 Product Description A premium white elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. A premium white elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. A premium grade high solids, single component, moisture cure, fluid applied silicone coating A premium grade high solids, single component, moisture cure, fluid applied silicone coating A single component, solvent, moisture cure silicone coating. A single component, solvent, moisture cure silicone coating. To be installed in a flood coat of approved asphalt at 60 lbs/sq To be installed in a flood coat of approved asphalt at 60 lbs/sq Application Rate 1-1 /2 gal/sq ASTM D6083 1-1 /2 gal/sq ASTM D6083 1.25 gal/sq ASTM D6694 1.25 gal/sq ASTM D6694 1.25 gal/sq ASS M D6694 •• • 1.25 gal/sq AO'M X8.694 400 lbs/sq 300 lbs/sq Specification • .•• . . • • n/A. • • • • • • • • ••• • Manufactur er Polyglass USA, Inc. Polyglass USA, Inc. Polyglass USA, Inc. Polyglass USA, Inc. •••• • •Aolyglass 1J AA Inc. •13olyglass • • USA, Inc. • • Generic • •. • • • •••• generic • • • ••• • NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 8 of 33 • • Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: 19/32" or greater plywood or wood plank. System Type D(1): All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently mechanically fastened through insulation to the roof deck. Membranes subsequently adhered. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more la e a ion La er, Any approved Polyisocyanurate listed in Table 2 Minimum 1" thick Top Insulation Layer (Optional) Fesco Board Minimum 3/4" thick Approved High Density Wood Fiberboard Minimum '/2" thick DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum %" thick Insulation Fasteners (Table 3) Fastener Density/ft2 N/A • N/A Insulation Fasteners Fa9tener (Table 3) •• • • Det► �2• • ••• • • •• • • • •••• N/A N/A •••• • • •••• • • •• •• • • 111,t1 • • • •• • • • • N/A :•dY�A • • • • • • • • • • Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a minimum a ' slication rate of two fasteners per board for insulation boards having no dimension greater than 4 rs for any insulation board having no dimension greater than 8 ft. or more plies of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor tened to the deck as described below: MIAMI•DADE COUNTY APPROVED Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast 14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners #14 with Polygrip Hex Plates or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet. One or more plies of Elastoflex SA V (1.5 -mm), Elastoflex SA V PLUS, XtraFlex SBS Base SA, Elastoflex SA V FR (1.5 -mm) or Elastoflex SA V PLUS FR, self -adhered. NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 22 of 33 • • One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self - adhered. Or One ply of Polyflex G, torch -applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General limitation #7.) MIAMI•DADE COUNTY APPROVED • • • •••• • • • ..• • .. • • • •••• • • • • • • .... • • .. • . . . • . . .. • • ........ • • • • • • • . • • • • • • .. . • • • ... • • • NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 23 of 33 WOOD DECK SYSTEM LIMITATIONS: 1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet. GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of-45ipsf. • • ....• 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force(U'vatue of i75112f., as • • tested in compliance with Testing Application Standard TAS 105. If the fastener value,. ,f1e141-testetl.hg,Below • 275 lbf. insulation attachment shall not be acceptable.• • 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment•is &sed ox a minimum• fastener resistance value in conjunction with the maximum design value listed within a specific system •S��iould the fastener resistance be less than that required, as determined by the Building Official!a:evised fa ener'. spacing, prepared, signed and sealed by a Florida registered Professional Engineer,, Regfsteif:t1 Architetf,'dl- Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilianie withdrawal' resistance value taken from Testing Application Standards TAS 105 and calculations inc ompliance witiq.lZoofing Application Standard RAS 117. • •• • • 7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements• of these areas. ¶ stener• densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61G20-3 of the Florida Administrative Code. END OF THIS ACCEPTANCE MIAMI.DADE COUNTY APPROVED NOA No.: 13-1217.01 Expiration Date: 10/11/17 Approval Date: 11/06/14 Page 33 of 33 • • • • • • • • TGFU.R14571 - Roofing Systems ONLINE CERTIEJCATWNS DJRECTOIY Pave Bottom See General Information for Roofing Systems POLYGLASS USA INC 1111 W NEWPORT CENTER DR DEERFIELD BEACH, FL 33442 USA TGFU.R14571 Roofing Systems Roofing Systems R14571 Page 1 of 10 SINGLE PLY MEMBRANE SYSTEMS Unless otherwise indicated, the insulation and base sheet are mechanically fastened in place; the membrane i5 heat welded in place. (Optional) Noncombustible deck classifications are applicable for use over combustible (15/32 in. min plywood) decks when 1/2 in. (min) gypsum board or 1/4 in. (min) G -P Gypsum "DensDeck @ Roofboard", "DensDeck Prime® Roofboard", "DensDeck DuraGiiard"' Roofboard" or V4 Si (rain) USG Corp SECUROCKTM Roof Board Type FRX-G are used directly over the combustible deck with all joints staggered.6 in. (r in) from AiYvopl • joints. • • • • Unless otherwise indicated, In any noncombustible roof deck Classification any UL Classified insulation may be utilized"•ndd•r•esth a !a en • • (min) G -P Gypsum "DensDeck ® Roofboard", "DensDeck Prime® Roofboard", "DensDeck DuraGuard•" Roofboard" or•l Minn)(iUSG Corp h4•n •• SECUROCKTM Roof Board Type FRX-G. • • • •••• • • • • General statement for use of vapor retarders and/or deck/insulation adhesives (NC decks only): When such vapor reta•d•r• •r deck/insolation adhesives are acceptable to POLYGLASS they may be utilized. • •• "POLYGLASS BASE", "MODIBASE", 'Polyglass G2 Base" may be used in lieu of any Type G2 base sheet in any NC Clas fs• icat8n. These predt&• may also be used in any C-15/32 Classification in which a generic Type G2 is referenced (i.e. not brand specific). "POSYC10656•Ply 4", "POLYGLASS Ply 6" (Type GI) and "POLYGLASS VENTED BASE" may be used in any NC Classification. These products may also.be%sedlh a: y C"15/2 • Classification in which a generic Type G1 is referenced (i.e. not brand specific). "BASE PRO" or "POLYFLEX SA BASE" may be used as an acceptable alternate of "ELASTOFLEX SA V" base sheet. References to polyisocyanurate insulation may include Polyglass Products "POLYTHERM®" and "POLYTHERM® Tapered". Acceptable alternates to the membranes listed are given below: • • ••• • • • • • • • • •• • ••• • • • • • •• Membrane Listed Acceptable Alternatives "POLYBOND" "MODIBOND" or 'Torch Pro Smooth" "POLYBOND G" "MOOIBONO G" or "Torch Pro Granular" "Polytherm", "Polytherm Tapered" or "Polytherm Composite" Insulations may be used wherever polyisocyanurate insulations are specified in the Classifications below. Insulation may be optional for any non-combustible deck roofing System unless the insulation acts as a coverboard over another insulation. The "Cure Technology" finish may be added to any Polyglass membrane without adversely affecting the UL Classification for that product/assembly. The product/assembly would maintain the same Classification with or without the "Cure Technology" process. Class A - Ballasted Incline: 3 1. Deck: C-15/32 Insulation: — Polyisocyanurate, urethane, perlite/polyisocyanurate composite, perlite/urethane composite, glass fiber, phenolic or perfite, any thickness. Ply or Base Sheet: — One ply "ELASTOBASE", "XtraFlex SBS GLASS Base", "ELASTOFLEX V", "ELASTOFLEX V -C", "XtraFlex SBS G HP" or "ELASTOSHIELD TS G. http://database.ul.com/cgi-bin/XYV/tem plate/LISEXT/1 FRAME/showpage.html?name=TGFU.R 14571 &cons... 11/27/2013 TGFU.R14571 - Roofing Systems Page 2 of 10 Membrane: — One or more layers "DUPLEX", "DUFLEX G", "POLYGLASS 350 CAP", "POLYFRESKO 350 CAP", "POLYBOND", "POLYBOND G", "POLYFLEX", "Xtraflex APP 5", "POLYFRESKO TORCH", "Xtraflex APP G", "XtraFlex APP G HP TOR" or "POLYFLEX G" (modified bitumen), heat welded, or one or more layers "ELASTOFLEX V", "ELASTOFLEX V -C", "ELASTOBASE", "XtraFlex SBS GLASS Base", "ELASTOFLEX S6", "XtraFlex SBS POLY Base", "ELASTOFLEX P -C", "XtraFlex SBS G HP" or "ELASTOSHIELO TS G", mopped In hot asphalt or heat fused. Surfacing: — Gravel, embedded in hot mopping asphalt. Class B - Ballasted 1. Deck: C-15/32 Incline: 3 Base Sheet: — Type G2. Membrane: — "DUFLEX", "DUPLEX G", "POLYBOND", "POLYGLASS 350 CAP", "POLYFRESKO 350 CAP", "POLYBOND G", "POLYFLEX", "Xtraflex APP 5", "POLYFRESKO TORCH", "POLYFLEX G° -dXtraF exaaPP-G'AP TOR" or "Xtraflex APP G" (modified bitumen), heat welded, or one or more layers "ELASTOFLEX V", "ELASTOFLEX V'C", "Ek. TOBASE", "XtraP'IL SBS GLASS Base", "ELASTOFLEX 56", "XtraFlex SBS POLY Base", "ELASTOFLEX P -C", "XtraFlex 555 G•fiP" of:'ELASTOSHIELD TS G ", mopped In hot asphalt. Surfacing: — Gravel, embedded in hot moppi g as It or heat fused. t / Class A -Fully Adhered 1. Deck: NC Incline: 1/2 , Insulation (Optional): — Polyisocyanurate,_urethane, perlite/polyisocyanurate composite, perlite/urethane composite, glass fiber, phenolic\or perlite, any thickness. Base Shket: — One or more layers "EIASTOBASE", "XtraFlex SBS GLASS Base", "POLYFLEX", "Xtraflex APP 5", "ELASTOFLEX V", "ELASTOFLEX V -C" or Type G2 base sheet, Membrane:,— "POLYBOND", "POLYBOND G", "POLYFLEX", "Xtraflex APP 5", "POLYFRESKO TORCH", "Xtraflex APP G", "XtraFlex APP 0 HP TOR" or "POL"(FLEX G" (modified bitumen), heat welded. •••• Surfacing: — 'PG 800 Asphalt Emulsion Roof Coating", applied at 3-4 gal/sq, or Kokem Products "Sunguard Piryfic P of Ceatint a� j • gal/sq; or Karna No. 97 Fibrated Aluminum Asphalt Roof Coating or Karnak No. 97 Asbestos Free Aluminum of Coatjng at 1. to i gal/. • sq; or Brewer "Fo ress 5001 Asphalt Emulsion", applied at 4 gal./sq., followed by "PolyPlus 60", applied at V.-1 yI./sqe. • • • • • • 2. Deck: C-15/32•••• Incline: 1/2 • • • Insulation: — Two or mor layers (insulation joints staggered a min of 6 in. from plywood deck'oints •••• • • P Y'joints) . �nyr�l4, • perlite/polylsocyanurate com site, perlite/urethane composite, glass fiber, phenolic or perlite, any thickness. Base Sheet: — One or more layers "ELASTOBASE", "XtraFlex SBS GLASS Base", "POLYFLEX", "Xtraflex APP 54116i.iSTOFLEX V'S, • • • • "ELASTOFLEX V -C" or Type 62 base sheet.• • • • • • Membrane: — "POLYBONO", "PQt BOND G", "POLYFLEX", "Xtraflex APP 5", "POLYFRESKO TORCH", "Xtraflex %l?P c'�"XtraFlex AFP 4 P TOR" or "POLYFLEX G" (modified bitumen), heat welded. • • • Surfacing: — "PG 800 Asphalt Emulsion Roof Coating", applied at 3-4 gal/sq, or Kokem Products "Sunguard rylicltot: Coating at 1 gal/sq; or Karnak No. 97 Fibrated Alumih(:m Asphalt Roof Coating or Karnak No, 97 Asbestos Free Aluminum orf Coating at 1 to Z 4344y,� • • sq; or Brewer "Fortress 5001 Asphalt Emulsion", applied at 4 gal./sq., followed by "PolyPlus 60", applied at 3/.-4 gat./sq., • • , • • • 3, Deck: C-15/32 • • • • •• • • • • N Incline: 1/2 • • •• • • Insulation: — 1/4 in. thick G -P Gypsum DensOeckQ;,perlite, wood fiber or glass fiber, 1 in., mechanically fastened. Base or Ply Sheet — One or more layers "POLYFLEX"'or "Xtraflex APP S" (mechanically fastened or heat welded), "ELASTOBA$E", "XtraFlex SBS GLASS Base", "ELASTOFLEX V", "ELASTOFIEX V -C" or Type G2 base sheet (mechanically fastened or hot mopped). Membrane: — "POLYBOND", "POLYBOND G", "POLYFLEX',ti:Xtraflex APP S", "POLYFRESKO TORCH", "Xtraflex APP G", "XtraFlex APP G HP TOR', or "POLYFLEX G" (modified bitumen), heat welded or rot mopped. Surfacing: — "PG 800 Asphalt Emulsion Roof Coating", applied'at 3-4 gal/sq. or Monsey Products "Endure Aluminum Roof Coating", "Weather Check" or "Pro -Grade Aluminum Roof Coating', 1.5 gal/Sp; or Karnak No. 97 Fibrated Aluminum Asphalt Roof Coating or Karnak No. 97 Asbestos Free Aluminum Roof Coating at 1 to 2 gal/ sq; or Brewer "Fortress 5001 Asphalt Emulsion", applied at 4 gal./sq., followed by "PolyPlus 60', applied at 3A-1 gal./sq.. 4. Deck: NC Incline: 1 Insulation (Optional): — Polyisocyanurate, glass fiber, perlite, wood fiber, any".combination, any thickness. Base Sheet: — "POLYFLEX" or "Xtraflex APP S" (mechanically fastened or heat welded) or Type G2, mechanically fastened or hot mopped. Membrane: — "POLYBOND", "POLYBOND G", "POLYFLEX", "Xtraflex APP 5", "POLYFRESKO TORCH', "Xtraflex APP G", "XtraFlex APP G HP TOR" or "POLYFLEX G" (modified bitumen), heat welded. Surfacing: — "PG 800 Asphalt Emulsion Roof Coating", applied at 3-4 gal/sq. or Grundy,)ndustries "al MB Aluminum Roof Coating" at 1-2 gal/sq; or Brewer "Fortress 5001 Asphalt Emulsion', applied et 4 gal./sq., followed by "PolyPlus 60", applied at 3/4-1 gal./sq.. 5. Deck: NC Incline: 1 • • • • • Insulation (Optional): — Polyisocyanurate, urethane, perlite/polyisocyanurate composite, perlite/Urethane composite, glass fiber, phenolic, perlite or wood fiberboard, any thickness, Base Sheet: — One or more layers "DUFLEX" or "POLYFLEX" or "XtraFlex APP S" (heat fused or mechanically fastened), "ELASTOBASE", "XtraFlex SBS GLASS Base", "ELASTOFLEX v", "ELASTOFLEX V -C" or Type G2 base sheet (hot mopped, heat fused or mechanically fastened), Membrane: — "DUPLEX G FR", "XtraFlex APP Dual", "POLYFRESKO TORCH FR", "Xtraflex APP G FR", "XtraFlek,APP G HP" or "POLYFLEX G http://database.ul.com/cgi-bin/XYV/template/LISEXT/IFRA ME/sh owpage.h tm 1?name=TGFU.R14571&ccns,.. 11/27/2013 TGFU.R14571 - Roofing Systems FR" \\(modified bitumen), heat fused. 6. Deck: C•'t5/32 Incline: 1/2 Page 3 of 10 Base Sh et: — One or more layers "DUFLEX" or "POLYFLEX" or "Xtraflex APP S" or "POLYGLASS Base" (heat fused or mechanically fastened), LASTOBASE", "XtraFlex SBS GLASS Base", "ELASTOFLEX v", "ELASTOFLEX v -C" or Type G2 base Sheet (hot mopped, heat fused or me anically fastened). Ply Sheet — , ne or more layers "DUPLEX" or "POLYFLEX" or "Xtraftex APP 5" or "POLYGLASS Base" (heat fused) or "POLYGLASS Base", "ELASTOBASE"",xtraFlex S8$ GLASS Base", "ELASTOFLEX V", "ELASTOFLEX V -C" or Type G2 base sheet (hot mopped) or mechanically attached. Membrane: — "D L.EX G FR", "XtraFlex APP Dual", "POLYFRESKO TORCH FR", "Xtraflex APP G FR", "XtraFlex APP G HP or "POLYFLEX G FR" (modified bitumen), heat fused, 7. Deck: C-15/32 Incline: 1/2 Insulation: — Polyisocyanurat�e (2 in, min), perlite (3/4 In. min), glass fiber (7/16 in. min), periite/polyisocyanurate composite, perlite/urethane composite (2 idmin) or (2 in. min) polyisocyanurate covered with 1/2 in. perlite or wood fiberboard. Base Sheet: — One or more !aye,.5 "DUPLEX" or "POLYFLEX" or "Xtraflex APP 5" (heat fused or mechanically fastened), "ELASTOBASE", "XtraFlex 565 GLASS Base", "ELAS ,0 FLEX V", "ELASTOFLEX V -C" (heat fused, mechanically fastened or hot mopped) or Type G2 base sheet (hot mopped or mechanically fbtened). Ply Sheet: — One or more layers "DU EX" or "POLYFLEX" or "Xtraflex APP S" (heat fused) "ELASTOBASE', "XtraFlex SBS GLASS Base", "ELASTOFLEX V", "ELASTOFLEX V -C" or pe G2 base sheet (hot mopped) or mechanically fastened. ' Membrane: — "DUFLEX G FR", "XtraFlex APP Dual", "POLYFRESKO TORCH FR", "Xtraflex APP G FR", "XtraFtex APP G HP" or "POLYFLEX G FR" (modified bitumen), heat fused. 8. Deck: NC '`,l Incline: 1/2 Insulation (Optional): — Polyisocyanurate, urethan'e,perlite/polyisocyanurate composite, perlite/urethane ormposire, glass fibe••rwrood fiberboard, phenolic or perlite, any thickness. 11, Base Sheet: — One or more layers "DUPLEX" or "POLYFL'EX" or "Xtraflex APP 5" (heat fused or mechanically fassltned),"ELASTQBAW, • "XtraFlex 585 GLASS Base", "ELASTOFLEX V", "ELASTOFLEX V -C" (hot mopped, mechanically fastened or hear f•sei)•o• Type G2 baes • sheet (hot mopped or mechanically fastened). ".. Membrane: — "ELASTOFLEX VG FR", "ELASTOSHIELD TS G FRt, "ELASTOFLEX 56 G FR", "XtraFlex SBS POLY ,V,•1tiyllftlex SBS POL'PG • T', "XtraFlex SBS GLASS 5", "XtraFlex SBS GLASS GT" or "POLYF\RESKO MOP FR" (modified bitumen), hot mopped orheat fused. • • • • •••• • 9. Deck: C-15/32 Incline: 1/2 Base Sheet "XtraFlex SBS Ply Sheet: — "ELASTOFL-EX Membrane: r , "XtraFlex 10. Deck: C-15/32 • •• • • • • • — One or more layers "DUFLEX" or "POLYFLEX" or "Xtraflex PP S" (heat fused or mechanically fastene• • • d, "ELASTOBASE•"", GLASS Base", "ELASTOFLEX V" or Type G2 base sheet (hot nkopped or mechanically fastened).: • One or more layers "DUFLEX" or "POLYFLEX" or "Xtraflex APP • 5" (heat fused), "ELASTOBASE", "YtreFlex $85 GLASS Baseil, V", "ELASTOFLEX V -C" or Type G2 base sheet (hot mopped or Mechanically attached). — "ELASTOFLEX VG FR", "ELASTOFLEX S6 GFR', 'POLYFRESKIS..MOP FR", "XtraFlex SBS POLY Q" "Y s ex SBS AOLY G SBS GLASS 5", "XtraFtex SBS GLASS GT" or "ELASTOSHIELD TS G'`FR" (modified bitumen), hot mapped or heat fuseid• • • • •• Incline: 1/2 Insulation: — Polyisocyanurate (2 in. min), perlite (3/4 in. min), glass fiber (15/16 in. mih), perlite/polyisocyanurate composite, perlite/urethane composite (2 in. min). Base Sheet: — One or more layers "DUFLEX" or "POLYFLEX" or "Xtraflex APP 5" (heat fuseddr mechanically fastened), "ELASTOBASE", "XtraFlex 585 GLASS Base", "ELASTOFLEX V", "ELASTOFLEX V -C" or Type G2 base sheet (hot mopped or mechanically fastened). Ply Sheet: — One or more layers "DUPLEX" or'POLYFLEX" or "Xtraflex APP S" (heat fused), "ELASTO6ASE","XtraFlex SBS GLASS Base", "ELASTOFLEX V", "ELASTOFLEX V -C" or Type G2 base sheet (hot mopped or mechanically attachedj:',, Membrane: — "ELASTOFLEX VG FR", "ELASTOFLEX 56 5 FR", "POLYFRESKO MOP FR", "XtraFlex SBS'QOLY G", "XtraFlex SBS POLY G T" , "XtraFlex SBS GLASS 5", "XtraFlex SBS GLASS GT" or "ELASTOSHIELD TS 5 FR" (modified bitumen), hat,mopped or heat fused. 11, Deck: NC Incline: 1 Insulation (Optional): — Cellular concrete, gypsum concrete, vermiculite concrete, perlite concrete or structura�'concrete. Primer: — Not UL Classified — as required by manufacturer. Membrane: — "POLYBOND", "POLYBOND G", "POLYFLEX", "Xtraflex APP S", "POLYFLEX G", "XtraFtex APP G HP TOR";Xtraflex APP 5", "Xtraflex APP G FR", "POLYFRESKO TORCH FR", "POLYFLEX", "Xtraflex APP 5", "POLYFLEX G", "XtraFlex APP G HP TOR"\"DUFLEX G FR", "XtraFlex APP Dual", "Xtraflex APP G FR", "XtraFlex APP G HP" or "POLYFLEX GFR". \ Surfacing: — (not required for "POLYFLEX G FR", "XtraFlex APP G HP", "XtraFlex APP Dual", "Xtraflex APP G FR", "POLYFRESKO TORCH FR" or °DUFLEX G FR') "PG 800 Asphalt Emulsion Roof Coating", applied at 3-4 gal/sq. or Monsey Products "Endure Aluminum Roof Coating", at 1.5 gat/Sq; or Grundy Industries "al MB Aluminum Roof Coating", at 1-2 gal/sq; or Brewer "Fortress 5001 Asphalt Emulsion",`applied at 4 gal./sq., followed by "PolyPlus 60", applied at 3/4-1 gal./sq, 12. Deck: NC Incline: 1 Insulation (Optional): — Any thickness, one or more layers UL Classified perlite, wood fiber, glass fiber, polyisocyanurate, polyisocyanurate/composite, EPS/wood fiber, EPS/perlite or EPS/composite. Base Sheet: — One or more layers Type 51 or G2. http://database.ul.com/egi-bin/XYV/template/LISEXT/l FRAME/showpage,html?name=TGFU.R14571&ccns... 11/27/2013 TGFU.R14571 - Roofing Systems 20. Deck: C-15/32 Incline: 2-1/2 Barrier Board: — 1/4 in. (min) G -P Gypsum DensDeck® with all joints staggered 6 in. from the plywood joints. Base Sheet: — Type G2, mechanically fastened. Membrane: — "POLYFLEX G FR", "XtraFlex APP G HP", "XtraFlex APP GFR" or "POLYFRE5K0 TORCH FR", heat fused in place. 21. Deck: C-15/32 Incline: 2 Page 5 of 10 Insulation (Optional): — Polyisocyanurate, penile, wood fiber or polylsocyanurate/periite board, any thickness. Barrier Board: — 1/4 in. (min) G -p Gypsum DensDeck®, mechanically fastened with all joints staggered 6 in. from the plywood joints. Base Sheet: — "ELAST08ASE", "XtraFlex SBS GLASS Base" (poly/sand), mechanically fastened or "ELASTOFLEX SA V PLUS FR", ELASTOFLEX SA V FR" or "ELASTOFLEX SA V FR BASE VENT" (self adhered). Ply Sheet (Optional): — "ELASTO8ASE", "XtraFlex SBS GLASS Base"(poly/sand), heat fused or mechanically fastened, or "ELASTOFLEX SA V PWS FR", "ELASTOFLEX SA V FR" or "ELASTOFLEX SA V FR BASE VENT", (self adhered). ,.,'Membrane: — "POLYFLEX SA P FR", "POLYFRESKO APP SA P FR", "ELASTOFLEX SA P FR", "POLYFRESKO SBS SA PFR", "ELASTOFLEX SA V FR HT", (self adhered) or "POLYFLEX G FR", "XtraFlex APP G HP", "Xtraflex APP G FR", G "POLYFRESKO TORCH FR", "DUFLEX G FR", "XtraFlex APPP Dual", "ELASTOFLEX S6 G FR", "POLYFRESKO MOP FR", "ELASTOFLEX VG FR", "XtraFlex SBS POLY G", "XtraFlex SBS POLY T", KaFiex SBS GLASS G", "XtraFlex SBS GLASS GT" or "ELASTOSHIELD TS G FR", heat fused. 5/32 Incline: 1/2 nsulation Polyisocyanurate Sheet: — Type G2, mechanically fastened followed by "ELAStTOBASE , " traF ex SBS GLASSp 5 Bae",m ch ni ally Base) with fastened. Ply Sheet (Optional): — "ELASTOFLEX SA V PLUS FR" , "ELASTOFLEX SA V FR" or "ELASTOPLEX SA V FR BASE VENT", (self adhered). Membrane: — "POLYFLEX SA P FR", "POLYFRESKO APP SA P FR", "ELASTOFLEX SA P FR", "POLYFRESKO S8S SA P FR", or "DUFLEX G FR", "XtraFlex APP Dual", "POLYFLEX G FR", "XtraFlex APP G HP", "Xtraflex APP G FR", "ELASTOFLEX S6 G FR", "POLYFRESKO MOP FR", "ELASTOFLEX VG FR", "XtraFlex SBS POLY G", "XtraFlex SBS POLY G T', "XtraFlex 565 GLASS G", "XtraFlex SBS GLASS GT" or "ELASTOSHIELD TS G FR", heat fused. • • • • • • • • •••• 23. Deck: NC Incline: 2 • • • •• • • •• • • • •••• • • • Insulation (Optional): — Atlas Roofing "ACFoam 1II" or "ACPoam II" or Hunter Panels "H -Shield", any thicknesse • • • • • • • Base Sheet: — "ELASTOBASE", "XtraFlex SBS GLASS Base"(poly/sand), heat fused or mechanically fastened or•lIigTOFLEX Se V FRS • • "ELASTOFLEX SA V PLUS FR" or "ELASTOFLEX SA V FR BASE VENT", (self adhered). Membrane: — "POLYFLEX SA P FR", "POLYFRESKO APP SA P FR", "ELASTOFLEX SA P FR", "POLYFRESKO SB5 SA0iA","ELASTSFLEX SA V • FR NT", (self adhered) or "POLYFLEX G FR", "XtraFlex APP G HP", "Xtraflex APP G FR", "POLYFRESKO TORCH FES" Flex APPguar,. • • "DUFLEX G FR", "ELASTOFLEX S6 G FR", "POLYFRESKO MOP FR", "ELASTOFLEX VG FR", "XtraFlex SBS POLY G*,i trarlex SES PLY•''s "XtraFlex S85 GLASS G", "XtraFlex SES GLASS GT" or " ELASTOSHIELD TS G FR", heat fused. • • • • •••• • • • 24. Deck: C-15/32 Incline: 3 • • • • • • • • Insulation /)_ fiber or Polyisocyanurate, wood lboard, �do n• • • • • • • Barrier Board: —4in. (min) G - Gypsum DesDeck®mechanically fastened with all joints staggered 6 in. from the plywoojts. Base Sheet: — "ELASTOBASE", "XtraFlex SBS GLASS Base' (poly/sand), mechanically fastened. • • Ply Sheet (Optional): — "ELASTOFLEX SA V PLUS FR" , "ELASTOFLEX SA V FR" or "ELASTOFLEX SA V FR BASE VENT", (self adhered). Membrane: — "ELASTOFLEX S6 G FR", "XtraFlex 555 POLY G", "XtraFlex SES POLY G T" or "POLYFRESKO MOP FR", heat fused. 25. Deck: NC Incline: 3 Insulation (Optional) ; — AtlaS Roofing "ACFoam III" or "ACFoarn II" or Hunter Panels "H -Shield", any thickness. Base Sheet: — "ELASTOFLEX SA V PLUS FR", "ELASTOFLEX SA V FR" or "ELASTOFLEX SA V FR BASE VENT" (self adhered). Membrane; — "POLYFLEX SA P FR", "POLYFRESKO APP SA P FR', "ELASTOFLEX SA P FR" or "POLYFRESKO SBS SA P FR." (self adhered). 26. Deck: NC Incline: 1/2 Base Sheet: — Type 61 or G2, mechanically fastened. Membrane: — "POLYFLEX G", "XtraFlex APP G HP TOR", "Xtraflex APP G" or "POLYBOND G", heat fused. 27. Deck: NC Incline: 3 Membrane: — "POLYFLEX SA P FR", "POLYFRESKO APP SA 9 FR", "POLYFRESKO SBS SA P FR"or "ELASTOFLEX SA P FR" (self adhered). 25. Deck: NC Incline: 1 Insulation (Optional): — Polyisocyanurate, any thickness. Base sheet (Optional): — "ELASTOFLEX SA V", "ELASTOFLEX SA V PLUS", "Xtrafiex SBS Base SA" or "ELASTOPLEX SA V BASE VENT", self -adhered or "ELASTOBASE", "XtraFlex SBS GLASS Base" (poly/sand), mechanically fastened. Membrane: — "POLYFLEX SA P", "Xtraflex APP G SA" "XtraFlex Kool APP G SA", or "POLYFRESKO APP SA P" self -adhered or "POLYFLEX FG FR", heat fused. http://database.ul.com/cgi-bin/XYV/template/LISEXT,' IFRAMEJshowpage.litml?name=TGFU.R 14571 &ccns... 11/27/2013 ►1 1) s4.022-1 33 MIAMFQADE COUNTY "Delivering Excellence Every Day" MIAMI-DADE COUNTY REQUIRED OWNERS NOTIFICATION FOR ROOFING CONSIDERATIONS It is the responsibility of the roofmg contractor to provide the owner with the required roofmg permit, and to explain to the owner the content of this form. The owner's initials in the designated space indicates that the item has been explained. 1. Aesthetics -workmanship: The workmanship provisions of Chapter 15 (High Velocity Hurricane one) are for the purpose of providing that the roofmg system meets the wind resistance and water intrusion performance standards. Aesthetics (appearance) are not a consideration with respect to workmanship provisions. Aesthetic issues such as color or architectural appearance, that are not part of a zoning code, should be addressed as part of the agreement between the owner and the contractor. 12. Renailing wood decks: When replacing roofmg, the existing wood roof deck may have to be renailed in accordance with the current provisions of Chapter 16 (High Velocity Hurricane Zones) of the Florida Building Code. (The roof deck is usually concealed prior to removing the existing roof system). 7-1/w/9 .... • • 3. Common roofs: Common roofs are those which have no visible delineation between i1Eig.orutg hb": • units (i.e. townhouses, condominiums, etc.). In buildings with common roofs, the roof�.ag,‘ontraCtorarid/or •• • owner should notify the occupants of adjacent units of roofmg work to be performed. • • .... •. . . 4. • Exposed ceilings: Exposed, open beam ceilings are where the underside of the roof ;acting can by • • viewed from below. The owner may wish to maintain the architectural appearance; tlleeTpte, roof nail penetrations of the underside of the decking may not be acceptable. The owner provideo•th option of • • • maintaining this appearance. • . . . . . 1 5. Ponding water: The current roof system and/or deck of the building may iibt drain AttLand may •• cause water to pond (accumulate) in low-lying areas of the roof. Ponding can be an indication of structural distress and may require the review of a professional structural engineer. Ponding may shorten the life expectancy and performance of the new roofmg system. Ponding conditions may not be evident until the original roofmg system is removed. Ponding conditions should be corrected. 171 6.Overflow scuppers (wall outlets): It is required that rainwater flow off so that the roof is not overloaded from a build up of water. Perimeter/edge walls or other roof extensions may block this discharge if overflow scuppers (wall outlets) are not provided. It may be necessary to install overflow scuppers in accordance with the requirements of: Chapter 15 and 16 herein and the Florida Building Code, Plumbing. 7. Ventilation: Most roof structures should have some ability to vent natural airflow through the interior of the structural assembly (the building itself). The existing amount of attic ventilation shall not be reduced. Owner's/Agent's Signature: Contractor's Signature: Property Address: Date: j / l / 1 Permit Number: 95t-12, r 1-rH 13